BioLAB 200 Series User manual

Operation Manual
Orbital Shaker
Series 200
Thank you for Choosing Biolab products. Please read the “Operating Instructions” and
“Warranty” before operating this unit to assure proper operation.

Index
C APTER 1 SAFETY WARNINGS AND GUIDELINES----------------------------------3
C APTER 2 INTRODUCTION----------------------------------------------------------5
C APTER 3 SPECIFICATION-----------------------------------------------------------5
C APTER 4 PREPARATION------------------------------------------------------------6
C APTER 5 OPERATION GUIDE------------------------------------------------------9
C APTER 6 FAILURE ANALYSIS AND TROUBLE S OOTING------------------------11
APPENDIX A: WIRING DIAGRAM OF ORBITAL S AKER----------------------------12
www.biolabscientific.com
2
Orbital Shaker BSOT series 200

01 Safety Warnings and Guidelines
1 Important operation information of the security
Users should have an entire conception of how to use the instrument properly before
operating it. Please read this operation manual carefully before using the instrument.
2 Security
The operation, maintenance and repair of the Instrument should comply with the basic
guidelines and the remarked warning below. Otherwise, it will affect the scheduled using life
of the Instrument and the protection provided.
www.biolabscientific.com 3
Orbital Shaker BSOT series 200
It is forbidden operating before read the operation manual. Read the
guidelines and directions below and carry out the countermeasure
according to them.
Before operation, read the manual carefully. These units are designed
for using in the laboratory environments by who’re knowledgeable in
safe laboratory practices.
This product is a normal and an indoor Instrument which conforms to
Standard B style- I.
The operator should not open or repair the instrument by himself.
Otherwise, the instrument will lose the qualification of repair guarantee
or cause accidents. The company will repair the instrument based on
warranty description.
The instrument should be put in the place where of low temperature,
little dust, no water, no sunshine or hard light, and of good aeration,
no corrosively gas or strong disturbing magnetic field, and far away
from central heating, camp stove and other hot resource. Do not put the
instrument in wet and dusty place. The vent on the instrument is
designed for aeration. Do not wall up or cover the vent.
A.C. power’s grounding should be reliable to safeguard against an
electric shock. The 3-pin plug supplied with thermo-shaker’s power
cable is a safety device that should be matched with a suitable
grounded socket.

3 Instruments Maintenance
The instrument and the accessories should be cleaned by cloth drenched with alcohol.
If there are smudges on the instrument, clean them with cloth.
4 After Service
1) Warranty Description
Within one month of delivery, the company is responsible of exchange for
breakdown caused by material or manufacture.
Within 12 months of delivery, the company is responsible of free repair for
breakdown caused by material or manufacture. Proven with defect under warranty, the
company will repair instrument.
Freight from user to maintenance department will be borne by user. Freight for
instrument resent to user will be borne by the company.
Repair out of warranty will be charged reasonable cost.
2) Warranty Coverage
Breakdown due to improper use, operation in inappropriate conditions, maintain or
refitting without authorization are not in warranty coverage.
www.biolabscientific.com
4
Orbital Shaker BSOT series 200
Pull the connector plug from the jack at once in the following case, and
contact the vendor.
There is some liquid flowing into the instrument;
Drenched or fire burned;
Abnormal operation: such as abnormal sound or smell;
Instrument dropping or outer shell damaged;
The function has obviously changed.
Power off when operation finished. If do not use the instrument for a
long period, pull off the connector plug, cover a piece of cloth on the
instrument to prevent from dust.

02 Introduction
The orbital shaker is powerful variable speed shaker which provides efficient orbital
motion. It is microprocessor controlled instrument with long-life brushless motor. It can be
applicable in different laboratories in microbiology, chemistry, immunology, biochemistry and
molecular biology.
Features:
1. Applicable in different laboratories.
2. Microprocessor control digital speed and working time
3. Low voltage designed
. Gentle, reliable mixing with long-life brushless motor
5. Universal platform, flat platform or platforms with clamps
03 Specifications
1. The Normal Operation Condition
Ambient Temperature: 4°C ~ 45°C
Relative umidity: ≤70%
Power: AC100-240V~ 1A
2. The Basic Parameters and Specifications
ype
Parameter BSO -201 BSO -202 BSO -203
Mixing Range 50 ~ 350rpm 50 ~ 300rpm 50 ~ 250rpm
Orbit 10mm 20mm 30mm
Timing Range 1min ~99h59min 1min ~99h59min 1min ~99h59min
www.biolabscientific.com 5
Orbital Shaker BSOT series 200

Max. Capacity 2.0kg 2.0kg 2.0kg
Power 50W 50W 50W
Dimension (mm) 284x264x108 284x264x108 284x264x108
Net Weight (kg) 5.6 5.6 5.6
04 Preparation
This chapter mainly describes the instrument’s mechanical structure, the keyboard and
functions of each key, as well as preparations before power on. Please learn this chapter well
before the orbital shaker is to be operated at the first time.
1 Structure Description
www.biolabscientific.com
6
Orbital Shaker BSOT series 200

2. Keyboard and Display Panel
3.Key Function
S AR /S OP
4. Power Connection
Put the instrument on a horizontal and even working table. Connect power as below
figure. DC socket is on the rear part of the instrument. Voltage should be between 100V
and 240V.
www.biolabscientific.com
Orbital Shaker BSOT series 200
decrease the time value or speed value
increase the time value or speed value
Key for start or stop. Press Start/Stop key to start or stop the
program.
AC100-240V

5. Platform Installation
Six kinds of platforms BX-103555, BX-103551, BX-103554, BX-103553, BX-103552, BX-
103556 are optional for orbital shaker.
1) Installation for BX-103555, BX-103551, BX-103552, BX-103556
www.biolabscientific.com
8
Orbital Shaker BSOT series 200
BX-103555
BX-103551
BX-103554 BX-103553

Take out the pad
of the platform.


Fix the platform with
M X8 screws.
Put back the pad to
the platform.

2) Installation for BX-103554 or BX-103553
05 Operation Guide
1. Speed and Timing Setting
a) All digital of LED display as the right chart when
power on. The instrument enters into the initial
program with beep.
Press  or  of speed key. It displays last running speed.
Refer to the right chart, it is “200” rpm. The unit digit flickers.
Press  or  of speed key to adjust the speed value.
Continuously pressing leads the value to increase or decrease
from unit digit, tens digit to hundreds digit.
E.g., to set the speed to 250rpm, continuously press
”” till speed value displays “250”, release the ””
key. The instrument confirms and saves the setting
value “250”.
www.biolabscientific.com 9
Orbital Shaker BSOT series 200




Take out the 2 flask
clamps in the
middle.
Fix the platform with
4 M4X8 screws.
Put back the 2 flask
clamps to the platform.
200
00:35
250
00:35

b) Press  or  of time key. It displays last setting
time. Refer to the right chart, it is “00:35” (timing is
35 minutes). The last digit flickers. Press  or  of
time key to adjust the timing value. Continuously
pressing leads the value increase or decrease in X10
speed.
E.g., to set the timing at 1hour 20 minutes, press
”” untill time value displays “01:20”, release the
 key. The instrument confirms and saves the
setting value “01:20”.
NO ICE: he timing value displays 00:00 means running timing is ∞.
2. Stop / Start
a) Press “start/stop” key to start or stop the program.
b) Press “start/stop” to run the program after speed and timing are set as requested.
When times up, instrument stops running and alerts.
c) Press “stop/start” to stop the running program.
d) When the program completes, or program stopped by pressing “stop/start” key, the
instrument will be in ready mode. In ready mode, press  or  of speed key or
timing key to reset speed and timing.
e) Press “start/stop” directly without adjust speed or timing in ready mode, the
instrument operate the program as last time.
www.biolabscientific.com
10
Orbital Shaker BSOT series 200
250
00:35
250
01:20

06 Failure Analysis and TroubleShooting
Failure Analysis and Processing Procedures
No. Phenomenon Possible Causes Processing Procedure
1No signal display when
power on.
No power Check the power
Broken switch Exchange the switch
Others Contact with the seller
2 Shaking heavily Samples placed
imbalanced Place the samples evenly
3
Actual speed and
displayed speed are not
matching
Broken controller Contact with the seller
4 Err displays Speed out of control Contact with the seller
www.biolabscientific.com 11
Orbital Shaker BSOT series 200

Appendix A: Wiring Diagram of Orbital Shaker
Below diagram is just for reference. It is subject to change without prior notice.）
Motor
L PE N
Earth
24V +
24V -
N PE
L
J2
J3
DC24V
M O TE R
ey and di splay
ey and di splay
PORT1
AC100V ~ AC240V
Main Board
www.biolabscientific.com
12
Orbital Shaker BSOT series 200

BIOLAB SCIENTIFIC LTD.
3660 Midland Avenue, Suite 300, Toronto, Ontario M1V 0B8 Canada
Email: [email protected] Tel: [phone]
Website: www.biolabscientific.com
www.biolabscientific.com 13
Orbital Shaker BSOT series 200