Biolase epic 10 User manual

5400442 Rev. C
Quick Setup Guide
BIOLASE, Inc.
4 Cromwell
Irvine, CA 92618 USA
949.361.1200 | 888.424.6527
www.biolase.com
MT Promedt Consulting GmbH
Altenhofstrasse 80
D-66386 St. Ingbert/Germany
[phone]
www.mt-procons.com
https://stomshop.pro/

5400442 Rev. C
For detailed instructions always refer to the EPIC™10 User Manual
SYSTEM PARTS LIST
The EPIC 10 laser system includes the following:
1. Laser Console (lithium ion battery
pack already installed)
2. Screen Protectors (Peel-off clear
screen cover - qty. 30)
3. Delivery System (installed)
4. Assorted Surgical Tips
5. Surgical Handpieces (2)
6. Three (3) pairs of protective laser
eyewear (two (2) pairs of doctor
safety glasses, one (1) pair of
darker patient safety glasses)
7. DC power supply and power cord
(one (1) US and one (1)
International)
8. User Manual
9. Welcome Kit (Welcome Letter,
BIOLASE store information, Quick
Setup Guide, Guide to Online
Training & Product Registration
Card, Limited Warranty
Information)
10.Laser Warning Sign
11.Tip Initiation Kit
12.Remote Interlock cable
13.Philips-head screwdriver (for
installing Footswitch batteries)
14.Footswitch
15.AAA batteries (2)
CAUTION: Federal Law restricts this device to sale by or on the order of a dentist
or physician or other licensed medical practitioner.
https://stomshop.pro/

5400442 Rev. C
THE LASER CONSOLE
SECTIONS 2.3, 2.5
THE HANDPIECE AND TIPS
SECTIONS 2.6, 2.8
Fiber Shaft Protective Cap
Handpiece
Surgical Handpiece Fully Assembled Disconnect the Handpiece
Insert Fiber Tip after assembling the handpiece (turn clockwise)
Remove Fiber Tip (turn counterclockwise)
Seating the Fiber Tip into the Handpiece
Bending the Tip
When the aiming beam is not present or
has a significantly asymmetrical shape:
►For tips that require initiation:
change the tip.
►For tips that do not require initiation:
change the tip; press to bypass
initiation requirement.
Amber > STANDBY
Green > READY
Blinking Green > Lasing
Blinking Blue > Pairing Active
LED Indicator
LED Indicator
Control Button
Handpiece Holder
The Laser Console arrives with the fiber already
inserted into the optical access port.
Fiber Storage Channel
https://stomshop.pro/

5400442 Rev. C
POWER ON
PASSWORD
TOUCH SCREEN DISPLAY
SECTIONS 4.2, 4.11
`
2
Power Switch
3
Wireless Signal
Strength
Laser Console
Battery Strength
Settings
Enter 888
1
NOTE: Before initial use, you must charge the battery!
SECTIONS 4.1, 4.2
https://stomshop.pro/

5400442 Rev. C
INITIATE THE TIP
SECTION 7.3
1
2
3
4
5
PAIRING (
IF NECESSARY
)
SECTION 4.4
1234
5
4
(If not paired)
https://stomshop.pro/

5400442 Rev. C
SECTION 11
MESSAGE REASON FIX
ERROR 1 THERMISTOR OPEN THERMISTOR OPEN
CALL BIOLASE SERVICE
ERROR 2 THERMISTOR SHORTED THERMISTOR SHORTED
ERROR 3 SHUTDOWN TEMPERATURE SYSTEM TOO HOT ALLOW 5-10 MINUTES FOR LASER TO
COOL DOWN
ERROR 4 LASER CURRENT HIGH/LOW OUTPUT IS OUT OF SPECSCALL BIOLASE SERVICE
ERROR 5 FOOTSWITCH SHORTED IN STANDBY FOOTSWITCH IS PARTIALLY
PRESSED OR IS DAMAGED
PRESS
/
RELEASE FOOTSWITCH OR CALL
BIOLASE SERVICE
ERROR 6 ON/OFF BUTTON STUCK KEY STUCK PRESS FRONT KEY
ERROR 7 FLASH CORRUPTED MEMORY CORRUPTED CALL BIOLASE SERVICE
ERROR 8 NO FIBER FIBER NOT INSERTED PLUG IN TRUNK FIBER
ERROR 9 LOST FOOTSWITCH COMMUNICATION WIRELESS INTERFERENCE REPOSITION CONSOLE OR FOOTSWITCH
TO IMPROVE COMMUNICATION
ERROR 10 EMERGENCY SWITCH E-SWITCH PRESSED PRESS E-SWITCH AGAIN
ERROR 11 REMOTE INTERLOCK REMOTE INTERLOCK OPEN CHECK REMOTE INTERLOCK CLOSED
ERROR 12 BATTERY CRITICALLY LOW BATTERY CRITICALLY LOW PLUG IN DC SUPPLY
ERROR 13 INTERNAL ERROR INTERNAL ERROR OCCURRED RESTART UNIT
ERROR 14 FOOTSWITCH BATTERY FOOTSWITCH BATTERY
CRITICALLY LOW
REPLACE FOOTSWITCH BATTERY
WARNING 1 TEMP HIGH SYSTEM IS HOT ALLOW
5-10
MINUTES FOR LASER TO
COOL DOWN
WARNING 2 BATTERY LOW BATTERY IS LOW PLUG IN DC SUPPLY
WARNING 3 BATTERY NOT CONNECTED BATTERY NOT CONNECTED PLUG IN BATTERY
WARNING 4 FOOTSWITCH BATTERY LOW BATTERY ON THE FOOTSWITCH
IS LOW
REPLACE FOOTSWITCH BATTERY
WARNING 5 FOOTSWITCH FOOTSWITCH HELD RELEASE FOOTSWITCH
ALERT 1 WIRELESS NOT PAIRED NO WIRELESS CONNECT RE-ESTABLISH PAIRING (SEE SEC 4)
ALERT 2
SYSTEM MUST BE IN READY MODE TO
LASE
SYSTEM IS NOT IN READY
MODE
PRESS THE CONTROL BUTTON IN ANY
PROCEDURE SCREEN
https://stomshop.pro/