Mix the correct amount of salt and
lukewarm water (approx. 24˚C) in a
bucket following the instructions
shown in the Mixing Salt Water section.
Never add salt directly to the
aquarium as it will kill your fish.
Using the cleaner pads provided,
remove any algae growth using the
rough side on stubborn marks only.
IP: White salt crystals may form
around the top and lid of the
aquarium; this is called ‘Creep’ and
should be wiped away with a damp
cloth. NEVER add these salt crystals
back into the aquarium.
Remove the old filter cartridge by
twisting the bubble tube counter-
clockwise, the bubble tube and filter
will lift away from the base.
Separate the bubble tube from the old
filter cartridge by holding the cartridge
and gently twisting the bubble tube in
a clockwise direction.
Using a jug or Cleaner Pump remove
25% of the aquarium water.
biOrb 30/biUbe = 7.5L/2GAL
LIFE S30/LIFE P45 = 7.5L/2GAL
biOrb 60/LIFE P60 = 15L/4GAL
JAgitating the ceramic media with the
Cleaner Pump will loosen any trapped dirt.
Making sure there is no ceramic media
or fish in the way, take the bubble tube
and filter cartridge assembled in Step 5
and insert into the aquarium giving the
bubble tube a quarter turn (as per
biOrb instructions). When positioned
correctly the bubble tube and filter will
remain in place.
Using the water prepared in Step 1, ensure all
salt has fully dissolved and test the Sg before
adding to your aquarium (see Checking and
adjusting the Sg overleaf). If the Sg is correct
add 50% of the water to your aquarium, wait
30 min and add the remaining 50%. Once
added you will need to re-check the Sg.
LAny sudden changes in the aquarium
water temperature could harm your fish.
1
2
3
4
Remove plastic wrapper from the new
marine filter cartridge and rinse with
water. Fit the new cartridge to the
bubble tube by locating all tabs and
twisting in a counter-clockwise direction.
LNever use a standard filter cartridge.
5
8
7
6
ixing salt water
Always mix salt in a clean bucket, NEVER in a stocked aquarium. If
you have a biOrb 60, two buckets may be required.
Follow the guidelines in the table below for mixing the correct
amount of Reef Salt for your aquarium.
AQUARIU SALT WEIGHT WATER WATER
VOLU E TE P.
biOrb 60/LIFE P60 500g/17.6oz (1 pack) 15L/4GAL 24˚C
biOrb 30/LIFE S30 250g/8.8oz (1
/2 pack)* 7.5L/2GAL 24˚C
biUbe/LIFE P45 250g/8.8oz (1
/2 pack)* 7.5L/2GAL 24˚C
*It is important to accurately weigh the salt before mixing with water.
If you have a biOrb CLASSIC 30, LIFE S30/P45 or biUbe you will have
1/2 pack of salt remaining. his should be kept in case you need to
adjust the salt concentration (Sg).
Measure the lukewarm water
(approx. 24˚C) accurately as you add
it to the bucket (this will ensure less
adjustment later). ow add the
correct amount of Reef Salt (see
table above) stirring continuously to
ensure all the salt is dissolved with
none remaining at the bottom of
the bucket.
NEVER use cold water as it will not mix
well with the Reef Salt and adding it to
your aquarium will harm your fish.
When mixing the saltwater in a
bucket, always add the water first and
then the salt to avoid the formation of
insoluble particles.
Add the sachet of Stress Coat to the
bucket of water and wait 24 hrs
before adding Stress Zyme. Check to
ensure ALL salt is dissolved and
using the thermometer/hydrometer
(provided in the Marine Conversion
Kit) check the water is approximately
24˚C and the salt concentration (Sg)
is correct before adding the water to
the aquarium (see Checking and
Adjusting the Sg for instructions).
15L
4GAL(US)
1
2
24˚C
24˚C
Please read these instructions carefully before starting.
We recommend that you change 25% of the water and the arine
Filter Cartridge every 4 weeks. If you are stocking more fish than
recommended it may be necessary to increase the frequency of the
water changes and invest in a test kit to check the water regularly.
Ideally perform step 1 & 2 at least 24 hours before starting step 3.
You will need:
A large clean bucket A Cleaner Pump
24˚C
3
24˚C
Downloaded from www.watergardeningdirect.com
