Bissell SPINWAVE 2307 User manual

SPINWAVE®
CORDLESS
_______________
USER GUIDE
2307, 2315 SERIES

www.BISSELL.com
2
WARNING
TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK OR INJURY:
» Do not use outdoors.
» Do not allow to be used as a toy.
Close attention is necessary when
used by or near children.
» Do not use for any purpose
other than described in this user
guide. Use only manufacturer’s
recommended attachments.
» Do not charge with damaged cord
or plug. If appliance is not working
as it should, has been dropped,
damaged, left outdoors, or
dropped into water, have it
repaired at an authorized service
center.
» Do not unplug by pulling on
cord. To unplug, grasp the plug,
not the cord.
» Do not handle charger, including
charger plug and charger
terminals, with wet hands.
» Do not put any object into
openings. Do not use with any
opening blocked; keep openings
free of dust, lint, hair, and anything
that may reduce air flow.
» Keep hair, loose clothing, fingers,
and all parts of body away from
openings and moving parts.
» Turn off all controls before
plugging or unplugging appliance.
» Use extra care when cleaning
on stairs.
» Do not use appliance in an
enclosed space filled with vapors
given off by oil-based paint, paint
thinner, some moth-proofing
substances, flammable dust, or
other explosive or toxic vapors.
» Use only BISSELL cleaning
formulas intended for use with
this appliance to prevent internal
component damage.
» Do not immerse. Use only on hard
floor surfaces moistened by the
cleaning process.
» Keep appliance on a level surface.
» Do not carry appliance while in use.
» Do not charge the unit outdoors.
» Use only the charger supplied by
the manufacturer to recharge.
» Do not incinerate the appliance
even if it is severely damaged. The
batteries can explode in a fire.
» Battery cell leaks can occur under
extreme conditions. If battery cell
contents comes in contact with the
skin or eyes: immediately flush with
water for 15 minutes. Seek medical
attention if irritation persists.
» Follow all charging instructions
and do not charge the battery
pack or appliance outside of the
temperature range specified in the
instructions. Charging improperly
or at temperatures outside of the
specific range may damage the
battery and increase the risk of fire.
» Do not expose a battery pack
or appliance to fire or excessive
temperature. Exposure to fire or
temperature above 130°C or 265°F
may cause explosion.
» Do not pull or carry by cord, use
cord as a handle, close a door on
cord, or pull cord around sharp
edges or corners. Do not run
appliance over cord. Keep cord
away from heated surfaces.
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING YOUR SPINWAVE®CORDLESS.
When using an electrical appliance, basic precautions should be observed, including the following:
WARNING
RISK OF INJURY. MOP PADS MAY
START UNEXPECTEDLY. UNPLUG
BEFORE CLEANING OR SERVICING.
This model is for household use only.
SAVE THESE INSTRUCTIONS
WARNING
›› Plastic film can be dangerous. To avoid danger of suocation, keep away from children.
›› To reduce the risk of electrical shock, turn power switch OFF and disconnect charger plug
from electrical outlet BEFORE performing maintenance or troubleshooting checks.

www.BISSELL.com 3
What’s In The Box?
NOTE: Standard accessories may vary by model. To identify what should be included with
your purchase, please refer to the “Carton Contents” list located on the carton top flap.
Thanks for buying a BISSELL®
SpinWave® Cordless
We love to clean and we’re excited to share one of our innovative
products with you. We want to make sure your hard surface floor
cleaner works as well as it does today for years to come, so this guide
has tips on using, maintaining, and if there’s a problem, troubleshooting.
Your cleaner needs a little assembly before getting to work, so flip to
the Assembly section on page and let’s get started!
Safety Instructions...........2
Product View & Assembly ...4
Formula .....................5
Operations ................5-11
Maintenance & Care ......12-13
Troubleshooting ............14
Warranty & Service .........15
Product Registration........16
(2) Scrubby
Pads
Handle (2) Soft Touch
Pads
(2) 8oz BISSELL
Multi-Surface Formula
Body of
Unit
Charging
Adapter
Plug
Storage Tray

www.BISSELL.com
4
Get to Know Your SpinWave® Cordless
Assembly
Insert handle into body of unit
until you hear a “click”.
WARNING
Do not plug in your SpinWave®Cordless until you are familiar with all instructions
and operating procedures.
3
2
1
4
7
10
1 Handle
2 Digital Controls
3 Battery Status Indicator Lights
4 Clean Water Tank
5 Low Profile Foot
6 Power Spin Pads
7 Spray Nozzle
8 Charging Adapter Plug
9 Storage Tray
10 Carry Handle
11 Charging Port
click
5
6
9
8
11

www.BISSELL.com 5
SPINWAVE® CORDLESS FORMULAS
Multi-Surface Formula Wood Floor Formula
Great for cleaning ALL
sealed hard floors Restore your sealed wood floors’ natural shine
WARNING
To reduce the risk of fire and electric shock due to internal component damage, use only
BISSELL cleaning formulas intended for use with the hard floor device.
Keep plenty of SpinWave®
Cordless formulas on hand so
you can clean your sealed hard
floors whenever it fits your
schedule. Always use SpinWave®
Cordless formulas in your
machine. Other solutions may
harm the machine and may void
the warranty.
Cleaning Formulas
Charging the Battery
Plug the adapter into a suitable wall
outlet. The battery status indicator
lights will illuminate when charging.
12
Before charging, make sure unit is
OFF by ensuring the battery status
indicator lights are not illuminated.
For maximum run time, charge unit for 4
hours prior to use. Refer to chart below
for understanding the charging status.
Insert the charging adapter plug into
the charging port on the back, right
side of the unit.
4h
34
NOTE: On first use, make sure unit is fully charged before use. To check the
battery status, turn the unit ON by puling the handle back and pressing the power
button. Battery is fully charged when all three blue status lights are illuminated.

www.BISSELL.com
6
Your BISSELL®SpinWave®Cordless machine has an LED light display that will
turn on when the power key is pushed to show the battery life status. All LED
color is blue.
BATTERY STATUS LIGHT STATUS
100% to 67%
66% to 33%
32% to 10%
> 10%
0%
In Use LED Display
NOTE: Keep the temperature range between 40-104 °F when charging the
battery, storing unit or during use.
WARNING
Overcharging may cause battery damage, fire or explosion.
TIP: Be sure to charge unit when there is less than 10% power left, one LED
flashing blue.

www.BISSELL.com 7
Attaching Mop Pads: Option 1
1
Your BISSELL®SpinWave®Cordless may
have come with two different mop pads:
(2) Scrubby Pads(2) Soft Touch Pads
The Soft Touch Pad is for everyday
use on delicate flooring like sealed
hardwoods and laminate.
The Scrubby Pad is used to power
through tough, sticky messes.
Your SpinWave®
Cordless may have
come with mop
pads attached. If
not, to attach mop
pads, carefully lay
machine down on
the floor.
2
The back of the mop pad
has a small dot in the
center of the pad.
Then, with the mop
pad folded, line up the
small dot in the center
of the pad with the
middle screw on the
bottom of the foot.
First, fold the pad in half,
making sure the cloth
material is inside the fold.
Lastly, line up the edge of
the mop pad with the inner
ring on the foot, attach
the mop pad to the hook
and loop material on the
bottom of the foot.
3
5
4

www.BISSELL.com
8
Attaching Mop Pads: Option 2
Your BISSELL®SpinWave®Cordless may
have come with two different mop pads:
(2) Scrubby Pads(2) Soft Touch Pads
The Soft Touch Pad is best for
everyday use on delicate flooring like
sealed hardwoods and laminate.
The Scrubby Pad is best used to
power through tough, sticky messes.
NOTE: These next steps are to help you apply the mop pads more accurately
onto the machine.
Place clean mop pads upside down in
the storage tray. The dot on each mop
pad should be facing up.
Hover the unit over the mop pads to
align in the center, then place the unit
down on the mop pads. Now they are
attached to the machine.
12

www.BISSELL.com 9
Filling Your Clean Water Tank
Lift the Clean Water Tank
straight up to remove
from the machine.
The Clean Water Tank is located
on the front of the machine.
Clean
Water
Tank
For small area cleaning
a. Fill Clean Water Tank with warm tap
water to the first water fill line.
b. Add BISSELL®SpinWave®Cordless
formula to the first formula fill line.
A few notes about filling the Clean Water Tank:
• Fill with warm (140°F/60°C MAX) tap water and add the appropriate
BISSELL solution. DO NOT USE BOILING WATER. DO NOT HEAT WATER
OR TANK IN MICROWAVE.
Unscrew the cap from
the Clean Water Tank.
The Clean Water Tank
has two measuring
volumes depending
on the amount of
space you would like
to clean.
For large area cleaning
a. Fill Clean Water Tank with warm tap
water to the second water fill line.
b. Add BISSELL®SpinWave®Cordless
formula to the second formula fill line.
Slide the Clean Water
Tank back into place
until you hear a click.
Screw the cap
back onto the
Clean Water Tank.
123
4
56

www.BISSELL.com
10
Cleaning Sealed Hard Floors
When fully charged, press the ON/OFF
button and the three LED lights will
illuminate.
Recline the body of the unit backward
to start the rotating mop pads.
1
TIP 3: For optimum cleaning, perform overlapping cleaning strokes while dispensing
cleaning solution. Care should be taken to not overwet the floor surface, especially
when cleaning wood and other delicate floor surfaces.
ATTENTION: This machine is designed to be used only on sealed hard floors and
should not be used on carpet or rugs. For best cleaning results, sweep or vacuum the
floor surface prior to using to avoid scratching or damaging floors from sharp debris.
TIP 1: You may feel a slight vibration when turning on the machine if the mop pads
are not aligned correctly. Wait a few seconds for the pads to adjust themselves. If this
doesn’t occur, turn the machine OFF and replace mop pads following the instructions
in “Attaching Mop Pads” sections.
TIP 4: When cleaning near baseboards, edges or furniture you may feel a slight pull
from the unit due to bouncing off the surface.
TIP 2: When you press the ON/OFF button to start the unit the LED lights will
illuminate, but the mop pads will not start rotating until the unit is reclined.
2

www.BISSELL.com 11
To clean, push the SPRAY button to
dispense solution.
Solution will spray out of the nozzle on
the front of the foot. You should hear a
soft buzzing noise each time you press
the SPRAY button to indicate solution
being dispensed.
For more difficult and stuck on messes, spray solution directly on mess and line
up one of the mop pads parallel to the mess. Move mop pad over mess and slowly
move machine back and forth to clean, continuing to spray solution as needed.
4
6
5
NOTE: When finished cleaning, make sure to push the OFF button before standing the
machine upright as the mop pads will continue to spin until the machine is turned OFF.
Cleaning Sealed Hard Floors (cont’d)
3
To power OFF the unit, press the unit ON/OFF
button and put unit into upright position. The
LED lights will turn off.
NOTE: If unit is on and gets placed in the upright position while still on, unit will go into
standby mode. To power OFF, press the ON/OFF button or the unit will turn off by
itself after 10 seconds of no action. You will know it is off when the LED lights are no
longer illuminated.

www.BISSELL.com
12
Cleaning Your SpinWave® Cordless
Machine wash separately in warm water.
Use only liquid detergents. Do not use
bleach or fabric softener. Tumble dry
on low. Do not iron. Do not dry clean.
To remove mop pads, simply pull pads
off the hook and loop material on the
bottom of the machine.
Store upright in storage tray in a dry,
protected area until the next use. Since this
product uses water, it must not be stored
where there is danger of freezing. Store with
dry mop pads. Wet mop pads may damage
wood and other delicate, sealed hard floors.
12
3
WARNING
Do not set the machine on carpet, rug or other fabric surface when mop pad is removed as
hook and loop material on foot may damage them.
WARNING
Do not store machine on wet mop pads as they may damage wood or other delicate floors.
NOTE: Any solution remaining in the Clean Water Tank should be emptied prior to
machine storage.
NOTE: Store cleaner in a protected, dry area. Since this product uses water, it must
not be stored where there is danger of freezing. Freezing may damage internal
components and void the warranty.

www.BISSELL.com 13
WARNING
This product contains lithium-ion rechargeable batteries. According to
Federal and State regulations, removal and proper disposal of lithium-ion
batteries is required. For removal of batteries in your SpinWave® Cordless,
see instructions on this page.
Disposing the Batteries
NOTICE: Disconnecting the battery will destroy the appliance and invalidate the
warranty.
With a Phillips-head
screwdriver, remove
the 5 screws on the
back of the unit.
Insert a screwdriver
into the hole on the
back of the unit
below the Carry
Handle in order
to disconnect the
handle.
1
4
NOTE: Keep Battery Pack together – DO NOT separate individual batteries.
For specific disposal instructions of batteries, please contact the RBRC
(Rechargeable Battery Recycling Corporation) at 1-800-822-8837
or visit www.Call2Recycle.org.
3
2
Before proceeding, ensure that:
-The unit is disconnected from the charger.
-The Clean Water Tank has been removed from unit.
-You have flat-head and Phillips-head screwdrivers and rubber-handled wire cutters.
Remove the control panel with battery
pack. For leverage, you may need to use
the flat-head screwdriver to help remove.
Insert flat-head screwdriver between
the top front and back plates located
between the Carry Handle and main
handle to remove the front body plate.
56
Disconnect the
8 inputs that
are connected
to the control
panel. Then,
using a Phillips-
head screwdriver,
unscrew the two
screws on the
control board.
Pull the control panel back from the
battery pack. Then, with rubber-handled
wire cutters, clip the two metal poles to
disconnect the battery pack from the
control panel.

www.BISSELL.com
14
Problem Possible causes Remedies
Unit is
vibrating/
wobbling
Mop pads are not aligned with
foot.
Realign the mop pads on the foot.
Reduced
spray OR
no spray
Clean Water Tank may be empty. Refill tank.
Clean Water Tank may not be
seated completely.
Turn power OFF.
Remove and Reseat Tank.
System isn’t completely primed. Hold trigger for 10 to 15 seconds to
make sure the solution has flowed to
the spray tips.
Not holding trigger to spray
solution.
Hold trigger continuously while using
the machine.
Spray tips on foot clogged. Turn power OFF. Use a pin to clean
the spray tip located front and center
of the machine.
Spin plates
are not
turning or are
wobbling
Mop pads are not installed
properly.
Turn Power OFF and follow instructions
on page 6 for replacing mop pads.
Machine is standing upright. Recline machine.
Machine is
leaking
Cap of Clean Water Tank is not
closed properly.
Remove the Clean Water Tank and
re-apply the cap.
Unit will not
charge
Charger plug/cord not
connected.
Make sure charger plug is completely
plugged into wall outlet and charging
cord is completely plugged into port
on the back of unit.
Not the correct charger. Use only the charger that comes with
machine.
All three (3)
LED lights
flashing
Pads forced to stop spinning,
potentially due to stuck debris,
compressed under furniture or
was briefly stepped on.
Turn the unit off or wait 10 seconds for
the lights and machine to turn OFF.
Then, press the ON/OFF to start the
unit again.
Heavy and extended usage may
cause internal temperature of
machine to warm up slightly
past the typical operating
temperature.
Press power button on handle one time
and wait for unit to cool down and
reset.
Two (2) LED
lights flashing
Functional issue with machine. Contact us for additional assistance.
Troubleshooting
WARNING
To reduce the risk of electric shock, turn power switch OFF and disconnect plug from
electrical outlet before performing maintenance or troubleshooting checks.

www.BISSELL.com 15
If your BISSELL product should require service:
Contact BISSELL Consumer Care to locate a BISSELL Authorized Service Center in
your area. If you need information about repairs or replacement parts, or if you have
questions about your warranty, contact BISSELL Consumer Care.
This warranty gives you specific legal rights,
and you may also have other rights which may
vary from state to state. If you need additional
instruction regarding this warranty or have
questions regarding what it may cover, please
contact BISSELL Consumer Care by E-mail or
telephone as described below.
It may be necessary to obtain some of your
personal information, such as a mailing address,
to fulfill terms of this warranty. Any personal data
will be handled pursuant to BISSELL’s Privacy
Policy, which can be found online at
www.BISSELL.com/privacy-policy.
Limited One-Year Warranty
Subject to the *EXCEPTIONS AND EXCLUSIONS
identified below, upon receipt of the product
BISSELL will repair or replace (with new,
refurbished, lightly used, or remanufactured
components or products), at BISSELL’s option,
free of charge from the date of purchase by the
original purchaser, for one year, any defective or
malfunctioning part.
See information below on "If your BISSELL
product should require service”.
This warranty applies to product used for
personal, and not commercial or rental, service.
This warranty does not apply to fans or routine
maintenance components such as filters, belts
or brushes. Damage or malfunction caused by
negligence, abuse, neglect, unauthorized repair,
or any other use not in accordance with the user
guide is not covered. This warranty will only be
valid if the product is used in the same country in
which it was sold.
BISSELL IS NOT LIABLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES OF ANY NATURE
ASSOCIATED WITH THE USE OF THIS PRODUCT.
BISSELL’S LIABILITY WILL NOT EXCEED THE
PURCHASE PRICE OF THE PRODUCT.
Some states do not allow the exclusion or
limitation of incidental or consequential
damages, so the above limitation or exclusion
may not apply to you.
*EXCEPTIONS AND EXCLUSIONS FROM THE
TERMS OF THE LIMITED WARRANTY
THIS WARRANTY IS EXCLUSIVE AND IN LIEU
OF ANY OTHER WARRANTIES, EITHER ORAL
OR WRITTEN. ANY IMPLIED WARRANTIES,
WHICH MAY ARISE BY OPERATION OF LAW,
INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, ARE LIMITED TO THE
ONE-YEAR DURATION FROM THE DATE OF
PURCHASE AS DESCRIBED ABOVE.
Some states do not allow limitations on how long
an implied warranty lasts, so the above limitation
may not apply to you.
Warranty
NOTE: Please keep your original sales receipt. It provides proof of date of purchase in the
event of a warranty claim.
Service
Please do not return this product to the store.
Other maintenance or service not included in the manual should be performed by an
authorized service representative.
For any questions or concerns, BISSELL is happy to be of service.
Contact us directly: US Consumers 1-800-237-7691 Canada Consumers 1-800-263-2533.
Website:
www.BISSELL.com/service-centers
E-mail:
www.BISSELL.com/email-us
Call:
BISSELL Consumer Care
US Consumers 1-800-237-7691
Canada Consumers 1-800-263-2533
Monday – Friday 8am - 10pm ET
Saturday 9am - 8pm ET
Sunday 10am - 7pm ET

16
©2018 BISSELL Homecare, Inc
Grand Rapids, Michigan
All rights reserved. Printed in China
Part Number 161-7187 07/18
Visit our website at: www.BISSELL.com
Registering is quick, easy and offers you benefits over the lifetime of your product.
You’ll receive:
Visit www.BISSELL.com/registration!
Visit the BISSELL website: www.BISSELL.com
When contacting BISSELL, have model number of cleaner available.
Please record your Model Number: ___________________
Please record your Purchase Date: ___________________
NOTE: Please keep your original sales receipt. It provides proof of purchase
date in the event of a warranty claim. See Warranty page for details.
BISSELL Rewards Points
Automatically earn points for
discounts and free shipping on
future purchases.
Faster Service
Supplying your information now
saves you time should you need
to contact us with questions
regarding your product.
Product Support
Reminders and Alerts
We’ll contact you with any
important product maintenance
reminders and alerts.
Special Promotions
Optional: Register your email
to receive notice of offers,
contests, cleaning tips, and more!
We c’t wait to ar from y!
Rate this product and let us (and millions
of your closest friends) know what you think!
www.BISSELL.com
Parts & Supplies
For Parts and Supplies, go to www.BISSELL.com and enter your model
number in the search field.
Register your product today!