Bissell EV675 User manual

NOTE : Be sure to install batteries in the remote.
Set the time by
pressing and
holding the clock
button on the
Remote Control
until the clock icon
on the Remote
Control display
begins to flash.
Use the
directional
arrows to set the
hour and minute.
Press the clock
button again to
save the time
setting.
NOTE: The robot
will beep once to
confirm the time
has been saved.
While the Power Switch
on the side of the robot is
OFF(0), press and hold the
play button on the remote
for 5 seconds until the clock
icon on the display flashes.
Continue to hold the play
button and turn the robot
ON (I).
NOTE: The robot will beep
three times to indicate that
it has successfully paired.
Assembly Instructions
Setting Up Your Robot Set the ClockPair the Remote to the Robot
WARNING
Refer to the enclosed user guide for complete
instructions and important safety notices.
EV675 ROBOTIC VACUUM
QUICK START GUIDE 2503 SERIES
161-8186 Rev 01/19
Package Contents
NOTE: Standard accessories may vary by model.
40"
79" 40"
Pleated Filter
(Located inside Dust Bin)
B I S S E L L®
EV675
Rechargeable
Li-Ion Battery
(Pre-installed)
Dust Bin
(Pre-installed)
Edge Cleaning
Brushes
Docking
Station
Power Adapter
(Charger)
Remote Control
(2 AAA Batteries included)
Cleaning ToolFoam Filter
(Located inside Dust Bin)
Place the back of Docking
Station firmly against a wall.
Ensure there are at least 40
inches to one side, 40 inches
to the opposing side and no
obstructions in front of the
Docking Station.
Insert the Docking Station
power adapter plug into
the port on the side of the
Docking Station and then
plug the other end into the
wall outlet. Turn ON the
unit’s Power Switch and put
on the Docking Station.
The first charge will take
4-5 hours.
1 12 2 1 2 3
NOTE : Be sure to install batteries in the remote.
Set the time by
pressing and
holding the clock
button on the
Remote Control
until the clock icon
on the Remote
Control display
begins to flash.
Use the
directional
arrows to set the
hour and minute.
Press the clock
button again to
save the time
setting.
NOTE: The robot
will beep once to
confirm the time
has been saved.
While the Power Switch
on the side of the robot is
OFF(0), press and hold the
play button on the remote
for 5 seconds until the clock
icon on the display flashes.
Continue to hold the play
button and turn the robot
ON (I).
NOTE: The robot will beep
three times to indicate that
it has successfully paired.
Assembly Instructions
Setting Up Your Robot Set the ClockPair the Remote to the Robot
WARNING
Refer to the enclosed user guide for complete
instructions and important safety notices.
EV675 ROBOTIC VACUUM
QUICK START GUIDE 2503 SERIES
161-8186 Rev 01/19
Package Contents
NOTE: Standard accessories may vary by model.
40"
79" 40"
Pleated Filter
(Located inside Dust Bin)
B I S S E L L®
EV675
Rechargeable
Li-Ion Battery
(Pre-installed)
Dust Bin
(Pre-installed)
Edge Cleaning
Brushes
Docking
Station
Power Adapter
(Charger)
Remote Control
(2 AAA Batteries included)
Cleaning ToolFoam Filter
(Located inside Dust Bin)
Place the back of Docking
Station firmly against a wall.
Ensure there are at least 40
inches to one side, 40 inches
to the opposing side and no
obstructions in front of the
Docking Station.
Insert the Docking Station
power adapter plug into
the port on the side of the
Docking Station and then
plug the other end into the
wall outlet. Turn ON the
unit’s Power Switch and put
on the Docking Station.
The first charge will take
4-5 hours.
1 12 2 1 2 3

NOTE : Be sure to install batteries in the remote.
Set the time by
pressing and
holding the clock
button on the
Remote Control
until the clock icon
on the Remote
Control display
begins to flash.
Use the
directional
arrows to set the
hour and minute.
Press the clock
button again to
save the time
setting.
NOTE: The robot
will beep once to
confirm the time
has been saved.
While the Power Switch
on the side of the robot is
OFF(0), press and hold the
play button on the remote
for 5 seconds until the clock
icon on the display flashes.
Continue to hold the play
button and turn the robot
ON (I).
NOTE: The robot will beep
three times to indicate that
it has successfully paired.
Assembly Instructions
Setting Up Your Robot Set the ClockPair the Remote to the Robot
WARNING
Refer to the enclosed user guide for complete
instructions and important safety notices.
EV675 ROBOTIC VACUUM
QUICK START GUIDE 2503 SERIES
161-8186 Rev 01/19
Package Contents
NOTE: Standard accessories may vary by model.
40"
79" 40"
Pleated Filter
(Located inside Dust Bin)
B I S S E L L®
EV675
Rechargeable
Li-Ion Battery
(Pre-installed)
Dust Bin
(Pre-installed)
Edge Cleaning
Brushes
Docking
Station
Power Adapter
(Charger)
Remote Control
(2 AAA Batteries included)
Cleaning ToolFoam Filter
(Located inside Dust Bin)
Place the back of Docking
Station firmly against a wall.
Ensure there are at least 40
inches to one side, 40 inches
to the opposing side and no
obstructions in front of the
Docking Station.
Insert the Docking Station
power adapter plug into
the port on the side of the
Docking Station and then
plug the other end into the
wall outlet. Turn ON the
unit’s Power Switch and put
on the Docking Station.
The first charge will take
4-5 hours.
1 12 2 1 2 3

NOTE : Be sure to install batteries in the remote.
Set the time by
pressing and
holding the clock
button on the
Remote Control
until the clock icon
on the Remote
Control display
begins to flash.
Use the
directional
arrows to set the
hour and minute.
Press the clock
button again to
save the time
setting.
NOTE: The robot
will beep once to
confirm the time
has been saved.
While the Power Switch
on the side of the robot is
OFF(0), press and hold the
play button on the remote
for 5 seconds until the clock
icon on the display flashes.
Continue to hold the play
button and turn the robot
ON (I).
NOTE: The robot will beep
three times to indicate that
it has successfully paired.
Assembly Instructions
Setting Up Your Robot Set the ClockPair the Remote to the Robot
WARNING
Refer to the enclosed user guide for complete
instructions and important safety notices.
EV675 ROBOTIC VACUUM
QUICK START GUIDE 2503 SERIES
161-8186 Rev 01/19
Package Contents
NOTE: Standard accessories may vary by model.
40"
79" 40"
Pleated Filter
(Located inside Dust Bin)
B I S S E L L®
EV675
Rechargeable
Li-Ion Battery
(Pre-installed)
Dust Bin
(Pre-installed)
Edge Cleaning
Brushes
Docking
Station
Power Adapter
(Charger)
Remote Control
(2 AAA Batteries included)
Cleaning ToolFoam Filter
(Located inside Dust Bin)
Place the back of Docking
Station firmly against a wall.
Ensure there are at least 40
inches to one side, 40 inches
to the opposing side and no
obstructions in front of the
Docking Station.
Insert the Docking Station
power adapter plug into
the port on the side of the
Docking Station and then
plug the other end into the
wall outlet. Turn ON the
unit’s Power Switch and put
on the Docking Station.
The first charge will take
4-5 hours.
1 12 2 1 2 3

NOTE : Be sure to install batteries in the remote.
Set the time by
pressing and
holding the clock
button on the
Remote Control
until the clock icon
on the Remote
Control display
begins to flash.
Use the
directional
arrows to set the
hour and minute.
Press the clock
button again to
save the time
setting.
NOTE: The robot
will beep once to
confirm the time
has been saved.
While the Power Switch
on the side of the robot is
OFF(0), press and hold the
play button on the remote
for 5 seconds until the clock
icon on the display flashes.
Continue to hold the play
button and turn the robot
ON (I).
NOTE: The robot will beep
three times to indicate that
it has successfully paired.
Assembly Instructions
Setting Up Your Robot Set the ClockPair the Remote to the Robot
WARNING
Refer to the enclosed user guide for complete
instructions and important safety notices.
EV675 ROBOTIC VACUUM
QUICK START GUIDE 2503 SERIES
161-8186 Rev 01/19
Package Contents
NOTE: Standard accessories may vary by model.
40"
79" 40"
Pleated Filter
(Located inside Dust Bin)
B I S S E L L®
EV675
Rechargeable
Li-Ion Battery
(Pre-installed)
Dust Bin
(Pre-installed)
Edge Cleaning
Brushes
Docking
Station
Power Adapter
(Charger)
Remote Control
(2 AAA Batteries included)
Cleaning ToolFoam Filter
(Located inside Dust Bin)
Place the back of Docking
Station firmly against a wall.
Ensure there are at least 40
inches to one side, 40 inches
to the opposing side and no
obstructions in front of the
Docking Station.
Insert the Docking Station
power adapter plug into
the port on the side of the
Docking Station and then
plug the other end into the
wall outlet. Turn ON the
unit’s Power Switch and put
on the Docking Station.
The first charge will take
4-5 hours.
1 12 2 1 2 3

NOTE : Be sure to install batteries in the remote.
Set the time by
pressing and
holding the clock
button on the
Remote Control
until the clock icon
on the Remote
Control display
begins to flash.
Use the
directional
arrows to set the
hour and minute.
Press the clock
button again to
save the time
setting.
NOTE: The robot
will beep once to
confirm the time
has been saved.
While the Power Switch
on the side of the robot is
OFF(0), press and hold the
play button on the remote
for 5 seconds until the clock
icon on the display flashes.
Continue to hold the play
button and turn the robot
ON (I).
NOTE: The robot will beep
three times to indicate that
it has successfully paired.
Assembly Instructions
Setting Up Your Robot Set the ClockPair the Remote to the Robot
WARNING
Refer to the enclosed user guide for complete
instructions and important safety notices.
EV675 ROBOTIC VACUUM
QUICK START GUIDE 2503 SERIES
161-8186 Rev 01/19
Package Contents
NOTE: Standard accessories may vary by model.
40"
79" 40"
Pleated Filter
(Located inside Dust Bin)
B I S S E L L®
EV675
Rechargeable
Li-Ion Battery
(Pre-installed)
Dust Bin
(Pre-installed)
Edge Cleaning
Brushes
Docking
Station
Power Adapter
(Charger)
Remote Control
(2 AAA Batteries included)
Cleaning ToolFoam Filter
(Located inside Dust Bin)
Place the back of Docking
Station firmly against a wall.
Ensure there are at least 40
inches to one side, 40 inches
to the opposing side and no
obstructions in front of the
Docking Station.
Insert the Docking Station
power adapter plug into
the port on the side of the
Docking Station and then
plug the other end into the
wall outlet. Turn ON the
unit’s Power Switch and put
on the Docking Station.
The first charge will take
4-5 hours.
1 12 2 1 2 3

NOTE : Be sure to install batteries in the remote.
Set the time by
pressing and
holding the clock
button on the
Remote Control
until the clock icon
on the Remote
Control display
begins to flash.
Use the
directional
arrows to set the
hour and minute.
Press the clock
button again to
save the time
setting.
NOTE: The robot
will beep once to
confirm the time
has been saved.
While the Power Switch
on the side of the robot is
OFF(0), press and hold the
play button on the remote
for 5 seconds until the clock
icon on the display flashes.
Continue to hold the play
button and turn the robot
ON (I).
NOTE: The robot will beep
three times to indicate that
it has successfully paired.
Assembly Instructions
Setting Up Your Robot Set the ClockPair the Remote to the Robot
WARNING
Refer to the enclosed user guide for complete
instructions and important safety notices.
EV675 ROBOTIC VACUUM
QUICK START GUIDE 2503 SERIES
161-8186 Rev 01/19
Package Contents
NOTE: Standard accessories may vary by model.
40"
79" 40"
Pleated Filter
(Located inside Dust Bin)
B I S S E L L®
EV675
Rechargeable
Li-Ion Battery
(Pre-installed)
Dust Bin
(Pre-installed)
Edge Cleaning
Brushes
Docking
Station
Power Adapter
(Charger)
Remote Control
(2 AAA Batteries included)
Cleaning ToolFoam Filter
(Located inside Dust Bin)
Place the back of Docking
Station firmly against a wall.
Ensure there are at least 40
inches to one side, 40 inches
to the opposing side and no
obstructions in front of the
Docking Station.
Insert the Docking Station
power adapter plug into
the port on the side of the
Docking Station and then
plug the other end into the
wall outlet. Turn ON the
unit’s Power Switch and put
on the Docking Station.
The first charge will take
4-5 hours.
1 12 2 1 2 3

Status Light Notifications
QUICK START GUIDE For further instructions
reference the User Guide or visit
www.BISSELL.ca
Schedule Cleaning Sessions Getting Ready to Clean
With Remote Control
Without Remote Control
Press the schedule button
on the Remote Control. The
icon will begin to flash on the
Remote Control display.
Use the directional arrows to
set the hour and minute for
your robot to start cleaning.
Press the schedule button
again to save the schedule
setting.
NOTE: The robot will beep
once to confirm the schedule
has been saved.
Press the Power
Switch to the ON(I)
position.
1 32
NOTE: Be sure the clock is set to the correct time before scheduling cleaning sessions.
NOTE: To cancel a scheduled cleaning session, press and hold the schedule button on the remote.
1 32 4
NOTE: Be sure the Power Switch on the Robot is set to the ON position.
You can change the cleaning pattern of the robot by pressing one of the following buttons:
Auto Mode
Robot will drive in a straight path until it encounters an obstacle and change direction.
Spiral Mode
Best for concentrated cleaning.
Wall Mode
Best for cleaning along walls and edges.
Single Room Mode
Best for cleaning a single room. It’s recommended that you close any doors to contain the robot.
Manual Mode
Best for directing the robot to a particular area.
Return to Dock
Press to return the robot to the Docking Station.
Status Light Colour Status
Breathing Blue Charging
Power Light O Robot Fully Charged
Solid Blue Cleaning
FOR ADDITIONAL INFORMATION ON ERROR NOTIFICATIONS AND OTHER TROUBLESHOOTING TIPS,
PLEASE REFER TO PAGES 12 AND 13 IN THE USER GUIDE.
Status Light Colour Status
Flashing Blue Returning to Docking Station
Flashing Red Error: Check Cliff Sensors, Battery Power Low, Robot is Trapped
Solid Red Error: Check Wheels, Edge Cleaning Brushes, Brush Roll, and Bumper
Press the Start/
Stop Button on the
top of the robot to
start cleaning.
When finished,
press the Start/
Stop Button again
to stop the robot.
When the vacuum
is in standby mode,
press the Start/
Stop button twice
continuously. The
vacuum goes into
recharging mode
with the button
flashing blue.

Status Light Notifications
QUICK START GUIDE For further instructions
reference the User Guide or visit
www.BISSELL.ca
Schedule Cleaning Sessions Getting Ready to Clean
With Remote Control
Without Remote Control
Press the schedule button
on the Remote Control. The
icon will begin to flash on the
Remote Control display.
Use the directional arrows to
set the hour and minute for
your robot to start cleaning.
Press the schedule button
again to save the schedule
setting.
NOTE: The robot will beep
once to confirm the schedule
has been saved.
Press the Power
Switch to the ON(I)
position.
1 32
NOTE: Be sure the clock is set to the correct time before scheduling cleaning sessions.
NOTE: To cancel a scheduled cleaning session, press and hold the schedule button on the remote.
1 32 4
NOTE: Be sure the Power Switch on the Robot is set to the ON position.
You can change the cleaning pattern of the robot by pressing one of the following buttons:
Auto Mode
Robot will drive in a straight path until it encounters an obstacle and change direction.
Spiral Mode
Best for concentrated cleaning.
Wall Mode
Best for cleaning along walls and edges.
Single Room Mode
Best for cleaning a single room. It’s recommended that you close any doors to contain the robot.
Manual Mode
Best for directing the robot to a particular area.
Return to Dock
Press to return the robot to the Docking Station.
Status Light Colour Status
Breathing Blue Charging
Power Light O Robot Fully Charged
Solid Blue Cleaning
FOR ADDITIONAL INFORMATION ON ERROR NOTIFICATIONS AND OTHER TROUBLESHOOTING TIPS,
PLEASE REFER TO PAGES 12 AND 13 IN THE USER GUIDE.
Status Light Colour Status
Flashing Blue Returning to Docking Station
Flashing Red Error: Check Cliff Sensors, Battery Power Low, Robot is Trapped
Solid Red Error: Check Wheels, Edge Cleaning Brushes, Brush Roll, and Bumper
Press the Start/
Stop Button on the
top of the robot to
start cleaning.
When finished,
press the Start/
Stop Button again
to stop the robot.
When the vacuum
is in standby mode,
press the Start/
Stop button twice
continuously. The
vacuum goes into
recharging mode
with the button
flashing blue.

Status Light Notifications
QUICK START GUIDE For further instructions
reference the User Guide or visit
www.BISSELL.ca
Schedule Cleaning Sessions Getting Ready to Clean
With Remote Control
Without Remote Control
Press the schedule button
on the Remote Control. The
icon will begin to flash on the
Remote Control display.
Use the directional arrows to
set the hour and minute for
your robot to start cleaning.
Press the schedule button
again to save the schedule
setting.
NOTE: The robot will beep
once to confirm the schedule
has been saved.
Press the Power
Switch to the ON(I)
position.
1 32
NOTE: Be sure the clock is set to the correct time before scheduling cleaning sessions.
NOTE: To cancel a scheduled cleaning session, press and hold the schedule button on the remote.
1 32 4
NOTE: Be sure the Power Switch on the Robot is set to the ON position.
You can change the cleaning pattern of the robot by pressing one of the following buttons:
Auto Mode
Robot will drive in a straight path until it encounters an obstacle and change direction.
Spiral Mode
Best for concentrated cleaning.
Wall Mode
Best for cleaning along walls and edges.
Single Room Mode
Best for cleaning a single room. It’s recommended that you close any doors to contain the robot.
Manual Mode
Best for directing the robot to a particular area.
Return to Dock
Press to return the robot to the Docking Station.
Status Light Colour Status
Breathing Blue Charging
Power Light O Robot Fully Charged
Solid Blue Cleaning
FOR ADDITIONAL INFORMATION ON ERROR NOTIFICATIONS AND OTHER TROUBLESHOOTING TIPS,
PLEASE REFER TO PAGES 12 AND 13 IN THE USER GUIDE.
Status Light Colour Status
Flashing Blue Returning to Docking Station
Flashing Red Error: Check Cliff Sensors, Battery Power Low, Robot is Trapped
Solid Red Error: Check Wheels, Edge Cleaning Brushes, Brush Roll, and Bumper
Press the Start/
Stop Button on the
top of the robot to
start cleaning.
When finished,
press the Start/
Stop Button again
to stop the robot.
When the vacuum
is in standby mode,
press the Start/
Stop button twice
continuously. The
vacuum goes into
recharging mode
with the button
flashing blue.
Status Light Notifications
QUICK START GUIDE For further instructions
reference the User Guide or visit
www.BISSELL.ca
Schedule Cleaning Sessions Getting Ready to Clean
With Remote Control
Without Remote Control
Press the schedule button
on the Remote Control. The
icon will begin to flash on the
Remote Control display.
Use the directional arrows to
set the hour and minute for
your robot to start cleaning.
Press the schedule button
again to save the schedule
setting.
NOTE: The robot will beep
once to confirm the schedule
has been saved.
Press the Power
Switch to the ON(I)
position.
1 32
NOTE: Be sure the clock is set to the correct time before scheduling cleaning sessions.
NOTE: To cancel a scheduled cleaning session, press and hold the schedule button on the remote.
1 32 4
NOTE: Be sure the Power Switch on the Robot is set to the ON position.
You can change the cleaning pattern of the robot by pressing one of the following buttons:
Auto Mode
Robot will drive in a straight path until it encounters an obstacle and change direction.
Spiral Mode
Best for concentrated cleaning.
Wall Mode
Best for cleaning along walls and edges.
Single Room Mode
Best for cleaning a single room. It’s recommended that you close any doors to contain the robot.
Manual Mode
Best for directing the robot to a particular area.
Return to Dock
Press to return the robot to the Docking Station.
Status Light Colour Status
Breathing Blue Charging
Power Light O Robot Fully Charged
Solid Blue Cleaning
FOR ADDITIONAL INFORMATION ON ERROR NOTIFICATIONS AND OTHER TROUBLESHOOTING TIPS,
PLEASE REFER TO PAGES 12 AND 13 IN THE USER GUIDE.
Status Light Colour Status
Flashing Blue Returning to Docking Station
Flashing Red Error: Check Cliff Sensors, Battery Power Low, Robot is Trapped
Solid Red Error: Check Wheels, Edge Cleaning Brushes, Brush Roll, and Bumper
Press the Start/
Stop Button on the
top of the robot to
start cleaning.
When finished,
press the Start/
Stop Button again
to stop the robot.
When the vacuum
is in standby mode,
press the Start/
Stop button twice
continuously. The
vacuum goes into
recharging mode
with the button
flashing blue.