BitFenix Spectre ARGB SE User manual

Spectre ARGB SE Controller
Introduction

•Rated voltage DC12V/DC5V
•With 6 ARGB 3Pin 5V sockets, 6 12-volt fan
sockets and ARGB & Fan headers connected
to Motherboard
•A single ARGB socket can bear 36 LEDs
•Fan sockets support a total of 36W
•A total of 60 lighting illumination modes
•If you connect the controller to the
Motherboard, press the switch of M/B sync
on remote to enter the Motherboard follow
mode and press the switch again to switch
the control to controller.
•If you connect the controller to the
Motherboard, press the switch of FAN AUTO
on remote to enter the Motherboard follow
mode and press the switch again to switch
the control to controller.
•This controller compatible with Asus AURA
SYNC, MSI Mystic Light, Gigabyte RGB Fusion
2.0 and Asrock Poloychrome SYNC, it also
can SYNC with BitFenix controller
Spectre ARGB SE Controller

How to connect the fans to the
controller Connect With Motherboard Connect With BitFenix Controller
Gigabyte MB
Please go to page 9 Please go to page 15Please go to page 20
OR

Spectre ARGB SE Controller
Connect to Gigabyte Motherboard
Addressable RGB 3pin socket
Connect to Fan
Addressable RGB 3pin socket
Connect to Motherboard(or Bitfenix controller) Addressable RGB 3pin socket
Front RGB switch
SATA power cable (Connect to Power supply )
Connect to
Motherboard
Fan socket
Please DO NOT connect VDG header and ARGB header together on Motherboard at the same time.+=Cable/LED

M/B sync: Switch to M/B control or controller control
Q1, Q2, Q3, Q4, Q5: Five different preset modes
Fan AUTO: Switch to Motherboard control or controller control
FAN +/-:Switch to High speed (100%RPM) and low speed (70%RPM) on controller
LED SPEED: Light speed adjustment for non-solid color mode(5 different speed)
HOLD: Lighting action play or pause
R: Red lighting mode
G: Green lighting mode
B: Blue lighting mode
Select mode up
Select mode down
Lock or unluck the button on remote
Spectre ARGB SE Remote

Spectre ARGB SE
Spectre ARGB SE Introduction

•This fan compatible with Asus AURA SYNC,
MSI Mystic Light, Gigabyte RGB Fusion 2.0
and Asrock Poloychrome SYNC
Dimension 120 x 120 x 25mm
Rated voltage DC 12V
Start Voltage ≦6V
Bearing Type Hydraulic Bearing
Speed 1200 ±200 RPM
Max Air Flow 33.2 CFM
Noise 24.4 dB-A
Power Consumption Fan: 2.4W LED: 1.5W
LED 8 PCS
Spectre ARGB SE

Connect to ARGB LED
connectoron motherboard
or controller with 3pin
ARGB LED connector
Connect to fan header
on motherboardor
controller for power
Spectre ARGB SE

How to Follow the Motherboard for fan speed
How to connect on Motherboard Fan socket
•If you connect the controller to the Motherboard, press the switch of FAN AUTO
on remote to enter the motherboard follow mode and press the switch again to
switch the control to controller.
•When the fan follow the controller, press FAN +/-to switch to high speed
(100%RPM) or low speed (70%RPM) on controller

How to connect the fans to the controller

ARGB LED connector
Connect to ARGB LED
connectoron motherboard or
controller with 3pin.
Fan power header
Connect to fan header
on motherboardor
controller for power.
How to connect the fans to the controller

How to connect ARGB header on controller
Each socket supports up to 36 LEDs
How to connect the fans to the controller

How to connect the fans to the controller
Please turn it over and plug in
How to connect fan header on controller
Fan sockets support a total of 36W

How to connect the fans to the controller
How to connect ARGB accessories on controller in Spectre ARGB SE Fan kit and use remote to control the
ARGB lighting
SATA
G ND
IN
5V
G ND
IN
5V
G ND
IN
5V

Connect With BitFenix Controller
Control by the button on case

Connect With BitFenix Controller
How to connect with Bitfenix controller (Dawn/ Saber/ Enso /Enso Mesh)
•If you connect the controller to BitFenix controller, press the switch of M/B sync on remote to switch different control method to BitFenix
controller and use the button which connected to the controller to control the ARGB lighting
M/B
sync
1
2
3

Connect With BitFenix Controller
How to connect with BitFenix 6+6 controller (Nova Mesh SE TG/ Enso Mesh 4xARGB)
•If you connect the controller to BitFenix 6+6 controller, press the switch of M/B sync on remote to switch the control method to BitFenix 6+6
controller and use the button which connected to the controller to control the ARGB lighting
1
M/B
sync
2
3

Connect With BitFenix Controller
Control by Remote

Connect With BitFenix Controller
How to connect with BitFenix 6+6 controller (Nova Mesh SE/ Enso Mesh 4xARGB)
•If you connect BitFenix 6+6 controller to the controller in Spectre ARGB SE Fan kit, long press the button on case till the
light flash white twice and it will switch the control method to the Fan kit controller and use the remote to control the
ARGB lighting.
1
2
3
Long press and the light will flash
white twice

Control by Motherboard