Toshiba BMS-CT2560U-E User manual

Central Control Device (Touch Screen Controller)
Installation Manual
• Save These Instructions!
ENGLISH
Model name:
BMS-CT2560U-E
(BMS-CT1280TU)
(BMS-CT2560U-TR)
For commercial use

2-EN
Central Control Device (Touch Screen Controller) Installation Manual
Contents
1 Precautions for safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3-1. Installation of Main Unit Box and Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3-1-1. When Installing from the Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3-1-2. When Installing from the Rear. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3-2. Attaching the Power Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3-3. Power, Signal, and Earth Line Connections . . . . . . . . . . . . . . . . . . . . . . . . . . 11
•Thank you for purchasing the system controller.
•Please read this installation manual carefully before installation, and perform the work only in the correct manner.

EN
3-EN
Central Control Device (Touch Screen Controller) Installation Manual
1Precautions for safety
• Read these “Precautions for safety” carefully before installation.
• The precautions described below include important items regarding safety. Observe them without fail.
Understand the following details (indications and symbols) before reading the body text, and follow the instructions.
• After the installation work has been completed, perform a trial operation to check for any problems. Explain how to use and
maintain the unit to the customer.
Ask customer to keep this Manual at accessible place for future reference.
Indication Meaning of Indication
Text set off in this manner indicates that failure to adhere to the directions in the warning could result in serious bodily
harm (*1) or loss of life if the product is handled improperly.
Text set off in this manner indicates that failure to adhere to the directions in the caution could result in serious bodily
injury (*2) or damage (*3) to property if the product is handled improperly.
*1: Serious bodily harm indicates loss of eyesight, injury, burns, electric shock, bone fracture, poisoning, and other injuries which leave
aftereffect and require hospitalization or long-term treatment as an outpatient.
*2: Bodily injury indicates injury, burns, electric shock, and other injuries which do not require hospitalization or long-term treatment as an
outpatient.
*3: Damage to property indicates damage extending to buildings, household effects, domestic livestock, and pets.
Symbols Meaning of Symbols
“ ” Indicates prohibited items.
The actual contents of the prohibition are indicated by a picture or text placed inside or next to the
graphic symbol.
“ ” Indicates compulsory (mandatory) items.
The actual contents of the obligation indicated by a picture or text placed inside or next to the
graphic symbol.
WARNING
•Ask an authorized dealer or qualified installation professional to install or reinstall
this unit.
Inappropriate installation may result in electric shock or fire.
•Electrical work must be performed by a qualified electrician in accordance with
this installation manual.
The work must satisfy all local, national and international regulations.
Inappropriate work may result in electric shock or fire.
•Be sure to turn off all main power supply switches before starting any electrical
work.
Failure to do so may result in electric shock.
•Do not modify the unit.
A fire or an electric shock may occur.
•Always connect to ground
Improper grounding may result in an electric shock.
Before connecting the power, carry out Class D grounding according to the “Engineering Standard
for Electric Work” and the “Internal Wiring Regulations”.
WARNING
CAUTION
Warning
This is a class A product. In a domestic environment this product may cause radio interference in which case the user may
be required to take adequate measures.

4-EN
Central Control Device (Touch Screen Controller) Installation Manual
CAUTION
• Do not install in the following locations:
Locations where combustible gas may leak
Locations with high humidity or water
Dusty locations
Locations in direct sunlight and locations subject to high temperatures
Locations within 1 m from televisions or radios
Outdoors, under awnings, or other locations exposed to rain and dew
Locations exposed to outside air containing corrosive gases or salinity
Locations with frequent vibrations
• Do not operate the touch panel with mechanical pencils or other pointed objects.
• In installation work, use wiring with the correct ampacity.
Failure to do so may result in excessive heat or fire.
• Use specified cables and connect them securely, and do not subject connecting
terminals to external force.
Doing so may result in broken cables, excessive heat or fire.
• Always install a circuit breaker on the primary side of the power supply.
• Clean the touch panel by wiping with an eyeglasses cleaner or other soft cloth .
To remove oil-based ink, wipe with a cloth that has been moistened with a neutral
detergent and then wrung out, and finish by wiping with a soft, dry cloth
.
Do not use commercial OA cleaners, cleansers, or other liquid cleaners containing
abrasives
.
• When attaching to a metal lath, wire lath or wooden structure with metal boards,
attach it to the control panel, etc. without attaching it to the wall.
• Do not swallow the coin cell battery.
There is a risk of injury due to chemical reaction if the battery is accidentally swallowed.
CAUTION This device uses a lithium battery. Follow all local regulations when disposing of it.

EN
5-EN
Central Control Device (Touch Screen Controller) Installation Manual
2Specifications
* Power cord for 220-240 V power adapter is to be arranged on site.
Outline drawing (Unit: mm)
System Controller
Product name Touch Screen Controller
Model Name BMS-CT2560U-E, BMS-CT2560U-TR
Power supply 220-240 V AC* 50/60 Hz
Consumed current 1.17 A
Number of
connected units
Indoor unit Up to 256 units
(LINK1 terminal: maximum 128 units, LINK2 terminal: maximum 128 units)
ON/OFF unit Maximum 60 units
Power meter interface Up to 4 units
Digital I/O interface Up to 4 units
Communication ports • RS-485 port ×1
• LAN port ×1
USB port USB memory stick connection port ×2
External contact input 8 inputs
External contact output 4 outputs
Operating temperature/humidity range 0°C to 40°C, 10% to 90% RH (no condensation)
Dimensions H136 mm × W205 mm × D10 (+80) mm
(Embedded dimensions shown in parenthesis)
Mass 1.34 kg (System Controller)
0.45 kg (power adapter)
80 10 80
205
152
181
202
20
20
20
20
53
10
5.8 5.8
ø 4.5
ø 4.5
ø 4.5
ø 4.5
90
133
91 136
190.4
90
115
M3 nut
M3 nut

6-EN
Central Control Device (Touch Screen Controller) Installation Manual
Power adapter
Component Names
Name Function
12V DCIN Connect the power adapter
Terminal block for external contact output Connect the external contact output
Terminal block for external contact input Connect the external contact input
LINK terminal block Connect the central control wiring
RS-485 terminal block Connect the RS-485 terminal block
USB For service
LAN Can be connected to a PC via LAN communication and monitored and controlled
Ø15.0
29.6±0.5
1500.0±20.0
30±5
110.0±0.5
62.0±0.5
Ø5.5±0.1
Ø2.5+0.1
-0
0.5 +0.15
-0.0
Ø12.0±0.5
6.5±0.3
33.0±0.5
7.5±0.3
+-
FERRITE AS REQUIRED
WIRE NO:1185
GAUGE:16AWG (BLACK)
SPEC LABEL
LED
31.5
MAX
COM
DI 4
COM
DI 3
COM
DI 2
COM
DI 1
LINK1 (Uh)INPUT LINK2 (Uh) RS-485
U3 U4 U3 U4 FGBA
COM
DI 8
COM
DI 7
COM
DI 6
COM
DI 5
INPUT
COM
DO4
COM
DO3
COM
DO2
COM
DO1
OUTPUT
12V DCIN
USB port ×2
LAN port
LINK1
Terminal block
RS-485 terminal
block
Terminal block for
external contact input
Terminal block for
external contact output
LINK2
Terminal block
<View from bottom>

EN
7-EN
Central Control Device (Touch Screen Controller) Installation Manual
Before Installation
Confirm that all the parts listed below are included in the package.
Included Items
Wiring specifications
Use the following wiring material to connect signal wires and power supply wires. (Locally procured)
No. Component name Quantity Remarks
1 System Controller 1
2 Power adapter 1
3 Owner’s Manual 1
4 Installation Manual 1
5 Fixing screw 4 Fixing screw (M4×12) for attaching the main unit from the front
6 Fixing screw 4 Fixing screw (M3×8) for attaching the main unit from the rear
7 Closed end connector 2 RS-485 cable crimp connector
8 Cable tie 2 For fixing the power adapter
9 Double-sided tape 1 For fixing the power adapter
No. Wiring Wire type / wire diameter / wire length
1 For LINK terminal Refer to "Design of Control Wiring" (P.13).
2 For RS-485 2-core shielded wires
1.25 mm2, up to 500 m (total extension distance)
3 For digital I/O Two-core cable
0.3 mm2, up to 100 m
4 For Ethernet LAN cable (category 5 or above)
Maximum length: 100 m

8-EN
Central Control Device (Touch Screen Controller) Installation Manual
3Installation
CAUTION
• Do not wire communication lines or input/output wiring next to power supply wiring, etc., or house them in the same metal
pipe. Doing so may result in failure.
• Install the main unit away from noise sources.
3-1. Installation of Main Unit Box and Panel
The main unit box can be mounted either from the front or from the rear.
3-1-1. When Installing from the Front
* Since the left and right mounting screws are attached close to each other, please drill the left and right dimensions as
accurately as possible.
1Connect the TU2C-LINK cable, AC adapter, and LAN cable to the main unit.
2Fit the main unit on to the wall and switch board.
3Insert a flat head screwdriver, etc. into the groove on the left and right of the bottom of the panel.
There will be a snapping sound and the panel will come off.
REQUIREMENT
• Just insert the screwdriver and do not twist it.
• To prevent the panel from falling, support it during removal.
4Fix the 4 main unit screws.
5Close the panel by hooking the panel rear to the top of the main unit.
There will be a snapping sound and the panel will be fixed.
6When installation is completed, peel off the transparent film.
Main unit box
Fix the panel with the
hooks.
Panel
183
120
100
133
20
93
53
202
190.45.8 5.8
20
20
System controller to wall, etc. fixing hole
dimensions
Do not twist
Hole dimensions to drill in wall
4-Ø4.5 round hole
4-M3 nut

EN
9-EN
Central Control Device (Touch Screen Controller) Installation Manual
3-1-2. When Installing from the Rear
* Although the panel and the main unit box are separated to explain the screw attachment part in an easy to understand
manner, it is not necessary to remove the main unit box from the panel in actual installation work.
1Drill four Ø4 holes in the switchboard, wall, etc.
2Fit the main unit on the switch board, wall, etc.
3Fix from the rear of the main unit. Please use the supplied M3 × 8 screws.
4Connect the TU2C-LINK cable, AC adapter, and LAN cable to the main unit.
5When installation is completed, peel off the transparent film.
Main unit box
Panel
183
120
100
133
20
93
53
202
190.45.8 5.8
20
20
System controller to wall, etc. fixing hole
dimensions Hole dimensions to drill in wall
4-Ø4.5 round hole
4-M3 nut

10-EN
Central Control Device (Touch Screen Controller) Installation Manual
3-2. Attaching the Power Adapter
The power adapter can be installed on a flat surface or on a wall. Do not install it in any other orientation.
Fix with the attached binding band and double-sided tape.
REQUIREMENT
Do not install in the following locations.
• Locations with high humidity or water
• Dusty locations
• Locations in direct sunlight and locations subject to high temperatures
• Locations within 1 m from televisions or radios
• Outdoors, under awnings, or other locations exposed to rain and dew
Installation allowed Installation not allowed
* Install so that the power cable that connects
to 220-240 V AC does not face upward.

EN
11-EN
Central Control Device (Touch Screen Controller) Installation Manual
3-3. Power, Signal, and Earth Line Connections
Connect the power, signal and earth lines to the specified terminal blocks.
REQUIREMENT
Attach round crimp terminals to all LINK 1, LINK 2, and RS-485 wiring, and tighten the screws securely. After tightening, check
that the wiring cannot come out.
COM
DI 4
COM
DI 3
COM
DI 2
COM
DI 1
LINK1 (Uh)INPUT LINK2 (Uh) RS-485
U3 U4 U3 U4 FGBA
COM
DI 8
COM
DI 7
COM
DI 6
COM
DI 5
INPUT
COM
DO4
COM
DO3
COM
DO2
COM
DO1
OUTPUT
Attach the AC adapter and
tighten securely until the screw
type fastener is fully fixed.Be
sure to connect the main unit and
the AC adapter before supplying
power to the AC adapter.
Outdoor unit
Indoor unit Remote controller
LINK 1 Outdoor unit
Indoor unit
Remote controller
LINK 2
RS-485 signal line
LINK1 and LINK2
terminals do not have
polarity
The RS-485 cable has polarity
(A, B). It will not work correctly if
it is connected with incorrect
polarity.
Connect the
shielded wire of the
RS-485 signal line
to the FG terminal
block.
Connection with
power meter
interface/digital
I/O interface
(sold separately)
Power connector
(DC 12 V)
Connect the shield of the TU2C-
LINK communication line to the
earth on the air conditioner side.
Leave the shield open (and
insulate it). Do not connect it to the
terminal block.
LAN cable
Functional earth
Connect the functional ground terminal
to the ground near the system
controller.
For DI1 to DI8, DO1 to DO4, and each COM, use a flat head precision screwdriver
to loosen the screws and open the insertion opening. After inserting the wiring,
securely tighten the screws with a precision screwdriver so that the wiring cannot
come out. After tightening, check that the wiring cannot come out.
USB port x2
LAN port
Client

12-EN
Central Control Device (Touch Screen Controller) Installation Manual
Termination resistance setting
•RS-485 termination resistance setting ...................Set at both ends of the RS-485 communication line. Set one end at the main
unit and the other end at the interface. The termination resistance of the main
unit is already set as a factory default. Refer to the interface installation
manual to set the termination resistance of the interface.
• TU2C-LINK / TCC-LINK
termination resistance setting ............................ <For TCC-LINK>
Leave just 1 line of the termination resistance in the interface board of the
outdoor unit (centre unit) ON, and turn all the others OFF. (Refer to the
wiring diagram attached to the outdoor unit for the position of SW.)
<For TU2C-LINK>
For the central control wiring (Uh line), set the termination resistance that is
farthest away on the wiring between this central controller and the other unit
(VRF, light commercial, air to air heat exchanger, general purpose control
interface, air to water heat pump) to ON.
Refer to the manual of each model for the termination resistance setting method.
Shield grounding process
•RS-485 cable wire shielded wire ......................... Connect to the FG terminal block.
• TU2C-LINK communication line shielded wire ......When using the system controller with one unit, open the shielded wire of the
TU2C-LINK communication line and perform insulation processing.
When using the system controller with multiple units, connect the shield of
the TU2C-LINK communication line to the closed end and open the shield at
the final end of the system controller to perform insulation processing.
Perform TU2C-LINK communication line shield grounding on the air
conditioner side.
REQUIREMENT
• Be sure to install a circuit breaker or all-pole isolating switch (with a contact breaking distance of at least 3 mm) on the
primary side of the power supply.
• Fasten the screws to the terminal block with torque of 0.5 N•m.
TU2C-LINK communication line stripping
length
RS-485 cable wire stripping length Digital I/O cable stripping length
Attach a round crimp terminal to each wire of the power line and
signal line.
Loosen the screws with a screwdriver, insert the digital I/O cable,
and tighten the screws securely.
35
35
55
635
Round crimp terminal
U3 U4
LINK (Uh)
U3 U4
LINK (Uh)
U3 U4
LINK (Uh)
U3 U4
LINK (Uh)
Termination resistance
ON
Termination resistance
OFF
Termination resistance
ON

EN
13-EN
Central Control Device (Touch Screen Controller) Installation Manual
Design of Control Wiring
Communication method and model name
The TU2C-LINK model (U series) can be used together with previous models (other than U series).
For details of the model and communication method, see the following table.
Communication method TU2C-LINK (U series) TCC-LINK (other than U series)
Outdoor unit Other than on the left
(MMY-MAP***, MCY-MAP***, etc.)
Indoor unit Other than on the left
(MM*-AP***, etc.)
Wired remote controller Other than on the left
Wireless remote controller
receiver Other than on the left
System controller Other than on the left
U series outdoor units: Super Multi u series (MMY-MUP***)
Outdoor units other than U series: Super Module Multi i series (MMY-MAP***), etc.
MMY-M P***
U series model
MM*- P***
U series model
RBC-AMS **
U series model
RBC-AXR **
U series model
TCB-AXR **
U series model
***-*** **
U series model

14-EN
Central Control Device (Touch Screen Controller) Installation Manual
When the connected outdoor unit is Super Multi u series (U series)
Follow the wiring specifications in the table below even when there is a mix of U series and non-U series in the connected indoor
units or remote controllers.
Wiring specifications
REQUIREMENT
When wiring the control wiring between indoor and outdoor units (Uv line)/control wiring between outdoor units (Uc line) and
the central control wiring (Uh line), use the same wire type and diameter for each line.
Using a mixture of different wire types and diameters may cause a communication error.
System diagram
* The wiring specifications in the system diagram above are the same even when the indoor unit or remote controller are other
than the U series.
Item Communication line
Central control wiring (Uh line)
Wire diameter 1.0 to 1.5 mm2(up to 1000 m)
2.0 mm2(up to 2000 m)
Wire type 2-core, non-polar
Wire types that can be used Shielded wire
U3 U4
LINK (Uh)
U6
U4
U1 U2
Uv
AB
U6
U4
U1 U2
Uv
AB
U6
U4
U1 U2
Uv
AB
U6
U4
U1 U2
Uv
AB
U2
Uv
U5 U6
Uc
U3 U4
Uh
U1 U2
Uv
U5 U6
Uc
U3 U4
Uh
U1 U2
Uv
U5 U6
Uc
U3 U4
Uh
U1
System
Controller
<U series>
Outdoor unit
(Super Multi
u series)
<U series>
Indoor unit *
<U series>
Remote
controller *
[Central control wiring (Uh line)]
L1 = Up to 2000 m
[Control wiring between indoor and outdoor units (Uv
line)/Control wiring between outdoor units (Uc line)]
L2 = Up to 1000 m
(L3+L4) = Up to 1000 m

EN
15-EN
Central Control Device (Touch Screen Controller) Installation Manual
When the connected outdoor units are other than Super Multi u series (U series)
Wiring specifications
REQUIREMENT
When wiring the control wiring between indoor and outdoor units/central control wiring and the control wiring between outdoor
units, use the same wire type and diameter for each line.
Using a mixture of different wire types and diameters may cause a communication error.
System diagram
* The wiring specifications in the system diagram above are the same even when the indoor unit or remote controller are other
than the U series.
Item
Communication line
Control wiring between indoor and outdoor units and central control
wiring
Wire diameter 1.25 mm2(up to 1000 m)
2.0 mm2(up to 2000 m)
Wire type 2-core, non-polar
Wire types that can be used Shielded wire
U2
U4
U3 U4
U3 U4
U6
U4
U1
Uv Uv Uv Uv
U2
A
B
U6
U4
U1 U2
AB
U6
U4
U1 U2
AB
U6
U4
U1 U2
AB
U1
U3
U2
U5 U6
U3 U4
U1 U2
U5 U6
U3 U4
U1
U2 U5 U6
U3 U4
U1
LINK (Uh)
System
Controller
<Other than U
series>
Outdoor unit
(Super Module
Multi i series
• Super Multi mini)
<U series>
Indoor unit *
<U series>
Remote
controller *
[Central control wiring/Control wiring between indoor
and outdoor units]
(L1+L2+L3) = Up to 2000 m
[Control wiring between indoor and outdoor units]
L4 = Up to 100 m

16-EN
Central Control Device (Touch Screen Controller) Installation Manual
When connecting to a previous model light commercial, air to air heat exchanger, air to water
heat pump, or general purpose equipment control interface
Follow the wiring specifications in the table below even when there is a mix of U series and non-U series in the connected indoor
units or remote controllers.
Wiring specifications
REQUIREMENT
When wiring the control wiring between indoor and outdoor units (Uv line)/control wiring between outdoor units (Uc line) and the
central control wiring (Uh line), use the same wire type and diameter for each line.
Using a mixture of different wire types and diameters may cause a communication error.
System diagram
* The wiring specifications in the system diagram above are the same even when the indoor unit or remote controller are other
than the U series.
Item Communication line
Central control wiring (Uh line)
Wire diameter 1.25 mm2(up to 1000 m)
2.0 mm2(up to 2000 m)
Wire type 2-core, non-polar
Wire types that can be used Shielded wire
U2
U4
U3 U4
U3 U4
U6
U4
U1
Uv
U2
A
B
U2
U5 U6
U3 U4
U1
U3 U4 U3 U4
LINK (Uh)
U6
U4 U4
A
BU6
4
Uh
A
B
System
Controller
Outdoor unit
and Other
Indoor unit *
Hydro unit
<U series>
Remote
controller *
[Central control wiring (Uh line)]
L1 = Up to 2000 m
[Control wiring between indoor and outdoor units
(Uv line)/Control wiring between outdoor units (Uc line)]
L2 = Up to 1000 m
Light Commercial
Air to air heat
exchanger
General purpose
equipment
control
interface
Air to Water
Heat Pump
TCC-LINK
adapter

EN
17-EN
Central Control Device (Touch Screen Controller) Installation Manual
Connection to External Devices
Example of connection to external equipment which is connected to digital input/output terminal.
* Wire the cables so that the user does not touch the power supply directly.
* On the external device side, use a basically insulated power circuit and place it in a location where the user cannot touch it.
Name I/O
Item
System controller side External device side
I/O conditions Terminal name Circuit example I/O conditions
State
output
Transistor
Open collector output
Terminal-to-common
allowable voltage /
current 24 V DC /
35 mA or less
Wiring length:
Within 100 m
* If you want to use
relays, please
refer to page 18.
Control
input
Electric
energy
pulse
Wiring length:
Within 100m
<Control input>
No-voltage
contact A
Pulse or static
<Electric energy
pulse>
No-voltage A
Pulse
Pulse width:
50 msec or more
No-voltage
contact
compatible with a
very small current
(3 mA or less)
DC5 V
DO1
Output
common
DO2
Output
common
DO3
Output
common
DO4
Output
common
DO1
Output common
Digital input
DO2
Output common
DO3
Output common
DO4
Output common
DI1
Input
common
DI2
Input
common
DI3
Input
common
DI4
Input
common
DI5
Input
common
DI6
Input
common
DI7
Input
common
DI8
Input
common
Input common
DI1
Input common
DI2
Input common
DI3
Input common
DI4
Input common
DI5
Input common
DI6
Input common
DI7
Input common
DI8

18-EN
Central Control Device (Touch Screen Controller) Installation Manual
When using a relay for the circuit on the equipment side of the state output
IMPORTANT
Be sure to connect freewheeling diodes to both ends of the relay coil. (A relay with a built-in diode is recommended.)
Wiring connections
This section shows wiring connection examples with the indoor units, power meter interface, digital I/O interface, and remote
monitoring PC.
Air conditioning unit group settings
• Indoor units can be set together for each group unit.
• Groups 1 to 64 correspond to the central control addresses 1 to 64 of the indoor units.
• There is a LINK 1 and a LINK 2 for each TU2C-LINK communication line.
If only U Series outdoor units are connected, each line has 128 groups. LINK1 and LINK2 together have 256 groups and 256
zones.
When outdoor units other than the U Series are connected, each line has 64 groups. LINK1 and LINK2 together have 128
groups and 128 zones.
*When an outdoor unit other than the U series is connected to either line, it is set when an outdoor unit other than the U series
is connected on both lines.
Interface connection
Connect the power meter interface and the digital I/O interface to the RS-485 cable line. For details of the connection method
refer to the interface installation manual.
When using the power meter, connect the power meter separately for each device.
• Multi air conditioners for buildings
• Light Commercial
• Room Air Conditioner (home) (RAC TU2C-LINK I/F connection * For use outside Japan only)
• Air to Water Heat Pump (Hot water supply)
• Air to Water Heat Pump (Air conditioning)
• Air to Water Heat Pump (Air conditioning and Hot water supply)
• General purpose device control interface, External device
35 mA or less
(Locally procured)
X2
Customer’s equipment
(digital input)
External power
supply
35 mA or less
DO1
DO2
Output common
X1
X2
X1

EN
19-EN
Central Control Device (Touch Screen Controller) Installation Manual
NOTE
When you remove the rear panel of this Unit, there is SW100 which is the termination resistance between LINK1 and LINK2
terminals.
For the central control wiring (Uh line), set the two terminating resistors at both ends of the wiring between this Unit and the air
conditioner to ON "Close" as much as possible.
Gr1 Gr5 Gr8 Gr16
Gr32Gr32
Gr32 Gr112
Gr2 Gr10
Gr17
Gr97 Gr99
Gr22 Gr25
Gr105 Gr107
Gr30
Gr109
Gr32 Gr128Gr113 Gr114 Gr119 Gr122 Gr124
Gr19
LINK1 terminal Central control wiring (Uh line)
LINK2 terminal
Central control wiring
(Uh line)
Group
1 to 16
Group
17 to 32
Group
97 to 112
Group
113 to 128
Gr = Group
Hub LAN cable
LAN cable
RS-485
Power meter
interface
Digital I/O
interface
Remote monitoring PC
Control wiring (Uv line)
Control wiring (Uv line)
Control wiring (Uv line)
Control wiring (Uv line)

DEB5869101-3