Salus TRV10RFM User manual

Wireless Radiator Controller
Model: TRV10RFM
INSTRUCTION MANUAL

02 TRV10RFM Instruction Manual
Contents of the box
Icons used in this manual:
Safety
Important info
TRV10RFM
2 AA Batteries
Adapter
Manual
Contents:
Box Contents
Introduction
Product Compliance and
Safety Information
Installation
User Interface
Status/LED indication
Installers notes
Warranty
Box Contents
For the latest PFD Instruction
Manual, go to
www.salus-controls.com

Product Compliance & Safety Information
INTRODUCTION
The TRV10RFM is a battery-powered, mini-size thermostatic radiator valve (TRV)
controller using ZigBee wireless communication. Simply replace the existing,
passive head on the standard radiator valve with the TRV10RFM (referred to
from now on as the unit). Use the unit with the VS10RF or VS20RF series of
wireless thermostats and a CO10RF wireless coordinator. The VS10RF or VS20RF
wireless thermostats are VS10BRF, VS10WRF, VS20BRF, and VS20WRF, where B
is the black model and W is the white model. You can optionally use the RX10RF
wireless boiler receiver and other iT600 wireless products.
Product Compliance
ThisproductisCEcompliantandmeetsthefollowingECDirectives:Electro-MagneticCompatibility
directive 2004/108/EC, R&TTE directive 1999/5/EC and ROHS2 directive 2011/65/EU.
Safety Information
Use in accordance with the regulations. The unit is to be used for the control of room temperature
inside the house.
Installation
This accessory must be tted by a competent person, and installation must comply with the
guidance, standards and regulations applicable to the country or state where the product is
installed. Failure to comply with the relevant standards could lead to prosecution.
VS10RF / VS20RF
Thermostat
(Required)
CO10RF
(Required)
RX10RF
(Optional)
SALUS Wiring Centre
KL08RF or KL10RF
TRV10RFM Instruction Manual 03

System Overview
To achieve the best control from the unit and thermostat, we recommend they
are used with the SALUS system receiver congured to RX1. The system receiver
will turn the boiler on or o when requested by the thermostat. See your boiler
receiver manual for more information about the RX1 conguration.
+
Up to three units can be connected to a VS10RF/VS20RF
The unit is modulating,
which means it opens
or closes partially
or 100% depending
on the relationship
between the actual
room temperature
and the required room
temperature measured
by the VS10/20RF.
04 TRV10RFM Instruction Manual

TRV10RFM Instruction Manual 05
Valve
1
32
Checking the compatibility of your heating system
The SALUS TRV10RFM is compatible with the majority of thermostatic radiator valves.
Before tting, please check your valve is suitable for use with the SALUS TRV.
Note: If all the measurements are as stated on this page then the TRV will
t directly to your valve. Also if your valve is not suitable please consider
changing your existing valves, contact your installer.
mm102030
mm102030
40
50
Remove the TRV head
Measure the thread
diameter (must measure
30mm)
Measure the pin length of the
valve when it is in the open
postilion. (must measure between
13-16mm)

06 TRV10RFM Instruction Manual
Checking the compatibility of your heating system
4
Our RA adapter also ts this valve.
Once tted the RA adapter should look like this.
If you can not see any thread on
the valve and it looks like this
picture, you may be able to use
the RA adapter supplied.

TRV10RFM Instruction Manual 07
1 2 3
4 5 6
Installing the Unit
Remove the battery door
on the side of the unit. Insert the batteries,
ensuring correct
orientation.
The LED on the unit ashes
green then flashes red
before changing to solid red.
When it is solid red, place
the unit over the radiator
valve using the mounting
ring if needed:
Screw the units nut
(finger tight) to the
radiator valve and check
that the LED is solid red.
The unit is now ready
for pairing to the SALUS
thermostat. You may now
start the pairing process
described on page 8.
Press any button on the
unit to adapt it to the
radiator valve. Once all
adaptation noise and LED
activity has stopped, the
unit is ready to pair with
your wireless thermostat.
See “LED Indications”
on page 12 if the LED
continues to ash.

08 TRV10RFM Instruction Manual
Preparing to Pair the Unit
1
Press and hold the button on the
CO10RF coordinator for ve seconds.
This puts the coordinator in pairing
mode. See your CO10RF Coordinator
manual for more information.
2
Ensure the wireless thermostat is powered up and ready for
pairing. See your thermostat manual for more information.
3
If you are using the optional RX10RF wireless boiler receiver
congured for remote boiler switching, ensure this has been
powered up and the red LED has gone from ashing to steady. See
your boiler receiver manual for more information.

TRV10RFM Instruction Manual 09
1
2
3
Pairing the Unit
Press and hold the pairing button for
10 seconds. You can pair up to three units with
one thermostat. Pair the units room by room.
Read page 38 to 40 of your wireless thermostat
manual when the red LED on the unit starts to
ash.
You have paired the unit to the thermostat when the unit LED goes o.
Once paired, the unit operates in automatic mode and receives room
temperatures from the thermostat.

10 TRV10RFM Instruction Manual
LED Indication
Pairing Button
Manual open/
status indication
Manual close/
status indication
Leaving the Network
Using the Unit
Once paired to a thermostat, press and
hold the pairing button on the unit for 10
seconds.
The red and green status LEDs come on
together for one second.
Note: After you have deleted the unit from
the wireless network, you must reinstall it
using the instructions from page 5.