Bitspower CR802 User manual

[ 1 ]
instruction manual
Accessories
Bitspower CR802 Reservoir V1
1BPM-WTCR802 1 SET
4M3x45mm Screw 4 PCS
5M3x5mm Screw 4 PCS
6M4x6mm Screw 4 PCS
2Mounting bracket (short) 2 PCS
3Mounting bracket (long) 2 PCS
7BPTA-PSC-SOC 1 PCS

[ 2 ]
Installation For Mounting bracket (short)
4
2
1
step 2
step 3
step 1
5
Assemble the M3x5mm screws Install the mounting bracket (short)
Assembly steps
7
Connector direction
in connection
Select the connector with label number
J1 and color black, which will let you
operate at low speed.
Select the connector with label number
J2 and color white, which will let you
operate at full speed.
Choose the speed what you need.

[ 3 ]
Dimension
Assembly steps
160
80
72.50
55
40
43
72.50
80
55

[ 4 ]
Assembly steps
step 3
4
3
1
step 2step 1
5
Installation For Mounting bracket (long)
step 3
Assemble the M3x5mm screws Install the mounting bracket (long)
7
Connector direction
in connection
Select the connector with label number
J1 and color black, which will let you
operate at low speed.
Select the connector with label number
J2 and color white, which will let you
operate at full speed.
Choose the speed what you need.

[ 5 ]
Assembly steps
Dimension
160
80
82
80
40
43
72.50
82

[ 6 ]
step 1
Recommend For Vertical stand(Additional purchases)
step 2
step 3
Method A
160
80
178
72.50
80
18
40
40
72.50
80
80

[ 7 ]
step 1 step 2
step 3
Method B
160
80
178
72.50
18
40
80
80
80

[ 8 ]
Recommend For Lighting module(Additional purchases)
step 1 step 2
step 3 step 4
Dimension (After installing the lighting module)
87
160
42.50
75
87
75.50
40
43
19

[ 9 ]
Dimension (After installing the lighting module and the vertical bracket)
160
80
87
108 80
42.50
80
80
80
72.50 75.50
108
The lighting module can be installed on surfaces in three di󽗈erent orientations.

[ 10 ]
記得上角要放對應的 LOGO!
Notice
Before filling in the water, please make sure all the components are
installed correctly. To prevent any leakage which may damage the PC
components, please perform a 24-hour leaking test with only the pump
connected to the power supply.
Bitspower reserves the right to change the product design and
interpretations. These are subject to change without notice. Product
colors and accessories are based on the actual product.
When using leak tester on water cooling loop, in order to avoid product
damage due to excessive pressure, the input pressure should not exceed
0.5kg/cm2 (Bar). If the product is damaged due to excessive pressure, it
will be the fault of the customer. DO NOT use the leak teser when there is
water in the loop or the pump is running.
Bitspower recommends that customers use Bitspower Pellucid Coolant
for their coolant fluid. It is also recommended to use Bitspower Dye to
create any desired color. If the customer chooses di󽗈erent liquid coolants,
the resulting impurities may cause peeling of the coating on some of the
hardware, water channel blockage by built-up residue, improper operation
of the water pump, water tank tube breakage, and o-ring deformation
leading to leakage. Any issues related to the use of inappropriate liquid
coolants will be the responsibility of the customer.