Panasonic DV0PM20105 User manual

购买年月日
型号
DV0PM20105
销售商店名
电话（ ）－
English
Operation Manual
Wireless LAN Dongle
Part No. D V ０ＰＭ２０１０５
■登记卡（为了今后咨询、修理时的需要, 请填写登记卡）
●
Thank you very much for purchasing the Panasonic product.
●
Carefully read this operation manual prior to use the product
correctly.
●
Always read “Cautions for Safety” prior to use.
●
Store this operation manual carefully.
●
This equipment is used only for the industrial purpose.
You cannot use in ordinary homes.
Read operation manual for setup support software down-
loaded from our website prior to use.
【PanasonicCorporationMotor Business Unit Website】
https://industrial.panasonic.com/ww/products/motors-
compressors/fa-motors
Hand over this operation manual to the end-user
.
－C28 －
IME98
Z1016-0
Caution
(1) Republication of any part or all of this document
without permission is prohibited.
(2) Contents of this document are subject to change
without notice.

－E2 －
－E3 －
English
Cautions for safety Be sure to comply with.
■Contents The
following section explains the items that y ou
page
Cautions for safety ..................................................... E3
Requests to use Wireless LAN Dongle ....................E7
Application ........................................................................ E10
Listed contents on the website.......................................... E10
1. Introduction............................................................E11
When you unpacked ......................................................... E11
shall comply with to prevent dangers to humans and
damage to properties.
■This section explains the level of dangers and
damages by the classification, which may occur
when the wrong usage is carried out.
The content that
Name of parts ................................................................... E12
Outline............................................................................... E13
2. Connection mode ................................................. E15
3. Connection............................................................ E17
4. Setting ................................................................... E18
5. General Specifications ......................................... E23
DANGER
WARNING
“it may result in death
or serious injury.”
The content that
“it may lead to death
or serious injury.”
6. When you are in trouble....................................... E25
Guarantee.................................................................. E27
Precautions for use .................................................. E28
Federal Communication Commission Interference
Statement ................................................................... E30
After-sales service.................................................... E32
■Following pictographic symbol explains the content
that you shall comply with.
The content that you shall not
perform.
The content that you must execute.

－E4 －
－E5 －
Do not use the product
in an airplane.
Otherwise, it may
cause problems to
the safety of aircraf t
operation.
Do not use the product
in a hospital or a place
where an electro-medi-
cal apparatus is placed.
The electric wave
from the product
may have an effect
on the electro-med -
ical apparatus and
cause accident due
to the abnormal
operation.
Do not use the product
when there is a person
nearby who has a car-
diac pacemaker.
Otherwise, the
electric wave may
adversely affect the
operation of pace -
maker.
Do not use near the
automatic control
equipment such as an
automatic door or a fire
alarm box.
The electric wave
from the product
may have an effect
on the automatic
control equipment
and cause accident
due to the abnor -
mal operation.
English
Cautions for safety Be sure to comply with.
DANGER W ARNING
Do not use the prod-
uct in the place where
water may splash over,
in the corrosive atmo-
sphere or flammable
gas atmosphere or near
the combustible ob-
jects.
Otherwise, it may
cause fire, electric
shock, malfunction
or breakage.
Do not install the prod-
uct near the heating ele-
ment such as a heater
or a large fixed wire-
wound resistor.
Otherwise, it may
cause fire or mal -
function.
Install the product in
the place with few dust
and water or oil is not
splashed over.
If the installation
place is not cor -
rect, it may cause
electric shock,
fire, malfunction or
breakage.
Always check the safety
after the occurrence of
earthquakes.
Otherwise, it may
cause electric
shock, injury or fire.
Ensure to install and set
the equipment so that
fire, accidentcausing
injury or death does not
occur in earthquakes.
Otherwise, it may
cause electric
shock, injury or fire.

－E6 －
－E7 －
Do not approach the
equipment because the
equipment may oper-
ate suddenly or the
movement may change
rapidly by changing the
setting.
Otherwise, it may
cause injuries.
The person who has a
cardiac pacemaker
shall keep the distance
22 cm or more off the
product.
Otherwise, the
electric wave may
adversely affect the
operation of pace -
maker.
To discard this product, process as the industrial waste.
English
Cautions for safety Be sure to comply with.
Requests touse Wireless LAN Dongle
◇Frequency band for use
The product uses the frequency band of 2.4 GHz band, and
also other wireless equipment may use the same frequency .
To prevent the radio wave int er f erenc e with other wir eles s
equipment, please use paying attention to the following t erms.
Cautions to use Wireless LAN equipment
In the frequency band for use of this equipment, the in-plant
radio stations for the mobile identification which is used on
the manufacturing lines in factories (Radio station that needs
the license), specified low power radio stations (Radio station
that needs no license) and amateur radio stations (Radio
station that needs the license) are operated in addition to the
industrial/scientific/medical equipment like microwave ovens.
1. Check that the in-plant radio stations for the mobile
i d en ti fi cati on, specified l o w power radio stations a nd
amateur radio stations are not operated in the vicinity
prior to use this equipment.
2. If the case of harmful radio wave interference occurred
from this equipment to the in-plant radio stations for the
mobile ident if ic at ion, immediately change the loc at ion
or stop the use of electric wave and then contact to our
company (Page E30) to have a talk about the action
to the interference avoidance (e.g. the installation of
partitions).
3. If you have any problem, for example; when the case
of harmful radio wave interference occurred from this
equipment to the in-plant radio stations for the mobile
identification or the amateur radio stations, please c ont ac t
to our company (Page E30).

－E8 －
－E9 －
English
Requests touse Wireless LAN Dongle (continued)
◇ Equipment qualification
The product needs no license of radio stations because it
has been approved for the certification of conformance to
technical standards in accordance with the Radio Act. How-
ever, it is prohibited to implement the following acts to the
product by the Radio Act.
・To disassemble or remodel,
・To
erase the nameplate attached to the side of product.
◇Usage restrictions
Please note that there are following restrictions to use t he
product.
When those restrictions are not complied, we deny any li -
ability for the incidental loss and damage raised by the use
of the product or the unusable product.
・Use the product as the wireless LAN equipment.
・The product can be
used only in the operational countries
listed on our website.
・The product is
designed to be able to operate in the coun -
try where the legal regulation standard is different. Set
the country code corresponding to the country to use the
product because the specified country code has been
set at manufacturing. Please set the code with great care
because it will be the violation of law if you set the wrong
country code.
・Do not connect to the wireless network which you
have no authorityof utilization.
During automatic search in the wireless network circum -
stances, a wireless network (SSID*) which you have no
authority of utilization may be indicated. It may be deemed
as an illegal access.
・Do not use the product where magnetic field/static
electrical charge/radio disturbance occurs.
When you use the product near the following equipment,
the communication may break up or the speed may be
slow.
・Microwave
oven
・Digital cordless telephone set
・Near the equipment that uses the electric wave of
2.4 GHz band.
E x a m p l e ; Equipment supporting Bluetooth, wireless
audio apparatus or game machine.
Select the wireless broad band router (Access point) of
802.11 n (2.4 GHz). Use the encryption scheme of “AES.”
・Transmitting and receiving data by electric wave may
be intercepted.
・To reduce the security risk of the interception of com-
munications or illegal access, set the password for the
access point and PIN code to set for the driver so as
to be complicated containing the alphanumeric char-
acters.
・You are required to set the country code.
Please set with great care because it will be the violation
of law if you set the wrong country code.
* It means the name to identify the specified network by wireless
LAN. When this SSID is matched by mutual equipment, t he
communication is enabled.

－E10 －
－E11 －
English
Requests touse Wireless LAN Dongle (continued)
Application
The product is the dedicated device to our
servo driver.
(You cannot use it by connecting to PC.)
●For the servo driver you can connect
with the product, terminals that can be
connected by wireless, setup of the
product and using method, check on
our website;
https://industrial.panasonic.com/ww/products/
motors-compressors/fa-motors
1. Introduction
When you unpacked
・Is the product type correct by your order?
・Is there any broken part during transportation?
If you found any defective portion, please contact the
retailer that you purchased the product.
Type confirmation
Nameplate is attached to the side of product.
When there is a person nearby who uses a pacemaker or
you cannot use the wireless LAN, please use the communi -
cation cable (Use USB mini-B connector for the driver, and
select a proper connector according to specification of the
Part No.
Serial Number
DV0PM20105
P16040001
R
201-160210
terminal.). Example: P 1 6 0 4 0 0 0 1 CMIIT ID :
2016DJ2804
Panasonic Corporation
Listed contents on the
website
・List of servo drivers possible to connect
・List of functions available in the wireless communications
・ Operating procedure manual of the setup support software
・ Countries where you can use the product.
・ Supported wireless authentication standards
・ Specifications of the recommended terminals
・ Specifications of the recommended access points
Sequential number
Manufacturing month
Manufacturing year (Last two digits of the Christian year)

－E12 －
－E13 －
English
1. Introduction(continued)
Name of parts
Wireless LAN Dongle
Lamp
(Blue LED)
Connector
Outline
This product is the wireless LAN dongle which enables the
wireless connection between the servo driver and your ter -
minals (PC, smartphones, tablet type terminals) by connect -
ing to the servo driver. When you use the Windows OS ap -
plicable setup support software “PANATERM” or the iPhone
terminals and Android terminals applicable setup support
software “Panasonic Motor Setup App,” it is required to con -
nect your PC and servo driver with cables, but the wireless
system will be possible by using this product.
The lamp shows the state of product when it is connected to
the servo driver .
●Lights on:
The state when the power is supplied to the product but it
is not communicating with the application. (Standby state)
●Low speed blinking (Light off 1 sec. Light on 1 sec.):
The state when communicating with the application.
(Communicating state)
●
High speed blinking (Light off 0.1 sec. Light on 0.1 sec.):
The state when the product failed to initialize and cannot
communicate. (Error state)
●Lights off:
The state when the power is not supplied to the product.
(Non-energized state)
Wireless
LAN
connection
By using this product and setup support software, primarily
the following items will be realized in wireless communica -
tion.
・Edition of parameters for the servo driver
・Monitoring the operation and inner conditions
・Monitoring and clearing the ala rm

－E14 －
－E15 －
English
1. Introduction
(continued)
However, you cannot use the product in the wireless com -
munication for the function to drive the motor, such as com -
missioning or frequency characteristics measurement.
Since the function which is available varies depending on
the using application, refer to the instruction manual of each
setup support software listed on the website for details.
The product cannot be connected to the Internet.
・ iPhone is the trademark of Apple Inc. registered in the
United States and other countries. The trademark of
iPhone is used based on the license of Aiphone Co., Ltd.
・Android is the trademark or the registered trademark of
Google Inc.
・Windows is the registered trademark or the trademark of
Microsoft Corporation in the United States and other coun -
tries.
・You can download “PANATERM” applicable to Windows
OS from our website.
・You can download “ P anas onic Motor Setup App” appli -
cable to iPhone terminals from App Store.
・For “Panasonic Motor Setup App” applicable to Android
terminals, the smartphone version and tablet version are
available. You can download either one from Google Play .
2. Connection mode
You can use the STA mode (Station mode) with the product.
●STA mode (Station mode)
This is the mode that this product operates as a station
(Wireless LAN adapter) and communicates with the terminal
via the equipment that operates as an access point (Wireless
LAN access point). When you connect in this mode, please
separately prepare the equipment which operates as an ac -
cess point. In addition, change the network setting of the ter -
minal and internal parameters in the driver so as to connect
with the prepared access point.
In this mode, all the products in the same local area network
can be selected from the terminal.
Access point

－E16 －
－E17 －
English
2. Connection mode
(continued)
The access point to be prepared shall s at is f y all the f ol-
l ow i ng specifications. If the fo ll o win g spe cifica ti o ns are n ot
satisfied, change the access point setting or prepare other
access point.
・The wireless communication standard supports either
IEEE 802 11 n, g or b.
・The security protocol
supports either WPA or WP A2.
・Use 2.4 GHz band as the frequency range (5 GHz band is
prohibited to use).
・
Communications between terminals located in the same
local area is permitted.
For recommended access points, please check them on our
website.
3. Connection
Connect the product to the connector X1 of the servo driver .
When servo driver is connected by wireless for the first time,
initial setup is necessary. Refer to “4. Setting” for details.
Connector X1
Product
Requests
Do not hook or place other wiring on the main body of
product.
Wireless LAN Dongle
Cable

－E18 －
－E19 －
Item
Description
Remarks
Security
Select either WPA or WP A2.
Select to match the setting of
the terminal and access point.
Default: WP A
Country
code
Select the country to use the
product. Please set with great
care because it will be the
violation of law if you set the
wrong country code.
Default: JP
SSID
Match to SSID of the access
point to be connected.
Settable number of characters:
1 to 32 characters
Accepted characters:
half-width characters 0 to 9,
a to z, A to Z, -, _
Default:
Panasonic
Servo000
(
(
English
)
)
4. Setting
The servo driver has the parameter for setting the wireless
LAN communications as the internal parameters. Before
starting the wireless communications with the product, it is
required to set (Initial setup) the parameters for wireless
LAN communications by the use of USB communication.
The following section shows the initial setup method. For the
initial setup, you need to install the setup support software,
and at the same time the terminal (i.e. Windows PC or An-
droid terminal) that can use the USB communication and a
USB mini-B cable is required.
1 Initial setup (Wired connection)
1. Connect the servo driver and terminal with the USB mini-
B cable.
Use a USB mini-B type in the marketplace as the driver
side connector. Select the terminal side connector to
match to the specifications of the terminal.
2. Start up the setup support software to start the communi -
cations with the driver .
3. Set the following parameters on the “Wireless LAN/Driver
Information Setting” screen of the setup support software
and then write those parameters in EEPROM of driver .
Connector X1 USB mini-B
cable
Prepare a cable
on the market.
PC
Connector X1 USB mini-B
cable
Prepare a cable
on the market.
Android terminal

－E20 －
－E21 －
Item
Description
Remarks
PWD
Match to the password of the
access point to be connected.
Settable number of characters:
8 to 32 characters
(*)
Accepted characters:
half-width characters 0 to 9,
a to z, A to Z, -, _, !, @, #, $,
%, ^, *, ,, ., /
Default:
Panasonic
Servo000
DHCP
When it is set valid, the IP ad -
dresses are automatically as -
signed from the access point.
When it is set invalid, you are
required to set the IP address
manually .
Default: Valid
IP address
Set the IP address to be used
when DHCP is invalid.
Set only when
DHCP i s i nval i d
Default:
192.168.0.1
Subnet
mask
Set the subnet mask to be
used when DHCP is invalid.
Set only when
DHCP i s i nval i d
Default:
255.255.255.0
Default
gateway
Set the default gateway to be
used when DHCP is invalid.
Set only when
DHCP i s i nval i d
Default:
192.168.0.1
English
4. Setting (continued)
Item
Description
Remarks
PIN code
Set the PIN code which is re -
quired when the setup support
software is used by wireless
connection.
At the start of wireless commu -
nication, the function cannot
be used by wireless communi -
cation if the PIN code set here
is not input.
Also, the function cannot be
used by wireless communica -
tion if the PIN code has not
been set.
Settable number of characters:
8 characters
(*)
Accepted characters:
half-width characters 0 to 9,
a to z, A to Z
Default:
Not set up
Driver
nickname
Set the driver nickname which
is indicated on the setup sup-
port software.
Settable number of characters:
1 to 8 characters
Accepted characters:
half-width characters 0 to 9,
a to z, A to Z, -, _
Default:
NoName
Setting is
voluntary .
* To ensure the safety on the security, set the password a nd
PIN code for the access point in the long and complicated
character string as much as possible.

－E22 －
－E23 －
Power
supply
DC 5V (Supplied from USB) 500 mA
Power
consumption
Max.2500 mW
Outline
dimensions
39.4
31.9
Unit: mm
Weight
Appr. 4 g
Ambient
temperature
for use
Temperature for use:
0 °C – 55 °C (Shall be no freeze)
Temperature for storage:
–20 °C – 65 °C (Sh al l be no cond e n sa ti on )
Ambient
humidity for
use
20 % – 85 % RH both for use and storage
(Shall be no condensation)
Interface
USB mini-B
Standards
Conformable to IEEE802. 1 1b/IEEE802.
11g/IEEE802. 11n
English
9.9
13
4. Setting (continued)
4. Turn off the power supply of d river .
The initial setup is now completed.
Next, establish the wireless system between the terminal
and driver by using the product.
5. General Specifications
1. Turn on the power supply of access point.
2. Connect the product to the connector X1 of the driver .
3. Turn on the power supply of driver and check that t he
lamp of the product lights up.
4. Change the network setting of the terminal you want to
use and connect to the target access point.
5. Use the terminal to start up the setup support software.
6. When the communication with the product has been suc -
ceeded, the nickname, part number and serial number of
the corresponding driver will be displayed on the driver
select screen.
7. When the driver is selected which is the target to connect,
the entry of PIN code will be requested, and so enter the
PIN code you set at the initial setup.
8. When the correct PIN code i s i np ut, the main screen o f
the setup support software will open.
Afterward, parameter setting or status monitoring can be
carried out by wireless communications by using the setup
support software.
For the method to use the setup support software, sepa -
rately refer to the operating manual of each setup support
software.

－E24 －
－E25 －
English
5. General Specifications (continued)
Frequency
range/Chan-
nels (Center
frequency)
2.412 GHz – 2.462 GHz
1 – 11 ch
Data transfer
speed
(Value of
standard *1)
IEEE802.11b: Max.11 Mbps
IEEE802.11g: Max.54 Mbps
IEEE802.11n: Max.72.2 Mbps
Access
system
Infrastructure mode
Security
WPA-PSK (TKIP/AES)
/WPA2-PSK (TKIP/AES)
Max.
trans -
mission
distance
(Prospect)
Indoors: Appr. 20 m (Varies depending on
the installation circumstances)
* １This is the theoretical speed and the actual communica -
tion speed differs due to the usage circumstances or the
connected equipment.
6. When you are in trouble
Q. I connected the product to the driver and then turned on
the power supply but the lamp of the product does not
light up (Power is not supplied). Or the lamp immediately
lights off.
A. The servo driver may not support the product. For the
supported servo drivers, please check them on our web -
site.
Q. The lamp of the product blinks at a high speed and the
communication is impossible.
A. The servo driver fails to read the parameters for setting
wireless communications. Contact failure with the con -
nector X1 may have occurred, therefore, reinsert the
product and then turn on the power supply again.
When the syndrome is not i mpro ved even if the a bove
action was taken, the servo driver may not be supported
in the system. Please check the supported servo drivers
on our website.
Q. The lamp of the product lights up, but the communication
is impossible.
A. Communication setting may be wrong. First of all, check
the wireless LAN/driver parameter setting of the servo
driver and check whether the SSID/password of the
access po i nt and parameter setting of the driver a re
matched, and whether the security protocol satisfies the
setting of access point.
Check if the same IP address as other equipment ha s
been set when DHCP is set invalid and the IP address is
set manually .

－E26 －
－E27 －
English
6. When you are in trouble (continued)
However, if the situation is not still improved, check
whether the network setting of the terminal is set to con -
nect to the target access point.
Also check that the access point is in accordance with
the specifications for access point as described before.
Q. Wireless communication breaks up during com munic a -
tions.
A. The wireless communication circumstances may be in
the interference. Check if the situation can be improved
by the method to change the communication channel or
eliminate the interference of communications after stop -
ping the wireless communication of other equipment.
Electric wave may be blocked off by obstacles. Since the
metal has property difficult to transmit the electric wave
in particular, the wireless communication may be impos -
sible if the circumstances are covered by metal.
Guarantee
Guarantee period
●The
guarantee period of the product sh al l be one yea r
after your purchase or one year and six months after our
manufacturing month.
Guarantee description
●We will
replace the product without charge when a failure
occurred in the guarantee period in the normal use
situation in accordance with this operation manual.
However, the following cases shall be charged even if it is
in the guarantee period.
(1) Failures caused by the wrong usage method and
improper repair or remodeling.
(2) Failures caused by the fall after the purchase and
damages during the transportation.
(3) Failures caused because the product is used beyond
the scope of specifications.
(4) Failures caused by fire, earthquake, lightning strike,
wind and flood, brine damage, abnormal voltage or
other Acts of God and disasters.
(5) Failures caused by the intrusion of water, oil, met al
fragments or other foreign matters.
●The
scope of the guarantee shall be only for the delivered
product unit. The damage induced by the f ailure of t he
delivered product shall be out of the scope.

－E28 －
－E29 －
English
Precautions for use
●
Cautions to export the product or the equipment installed
with the product.
When the final user or the final application of the product
is involved in the military affair or weapons, make sure to
take the sufficient probation and required export proce -
dures because the situation may be subject to the export
control regulated by the “ Foreign Exchange and Foreign
Trade Control Law.”
●The product is
manufactured only aiming at the use for
general industria l products but not designed or manufac -
tured for the purpose to be used with the equipment or the
system involving human lives.
●The
specialist who has the knowledge shall perform deal -
ing with the product such as the installation, wiring, opera -
tion, maintenance and inspection.
●To apply to the facility where the
occurrence of serious
accident or damage is forecasted due to the failure of the
product, make sure to install the safety device.
●
If you conduct a study on the use of product in the special
c ir c um s t anc es as for the nuclear energy control, aer o -
space instruments, transport facilities, medical equipment,
various safety devices and equipment that demands the
cleanness class, please contact us.
●We make our maximum effort to
ensure the quality of the
product, however, please take it into consideration to es -
tablish your fail safe design and ensure the safety in the
operable range at the operation place because the product
may generate unexpected actions caused by the loading
of external noise or static electrical charge exceeding ex -
pectation or the possible failure of the input power source,
wiring or parts.
●The
wireless communications may break out and the f unc -
tion may not be accomplished normally due to the inter -
ference in the wireless communication circumstances or
the cause that the far distance between the product and
access point or the access point and terminal, communi -
cation interception by obstacles such as the metal which
blocks electric waves, failure of the terminal or a ccess
points. When the communication breaks out, please check
the using wireless communication circumstances and the
condition of using terminals and access points.
●Since this product
uses radio wave and it may generate
unexpected actions by the delay unt il the result is reflect ed
actually on the movement of equipment when the setting
change is carried out, please check there are no people
around the site when the setting is changed and please
take it into consideration to ensure the safety.
●
Smoke of a cigarette may be generated depending on the
content of f ailur e of the product. Give consideration to it
when the product is used in a clean room.
●When the product is
used in the environment where the
concentration of sulfur or sulfide-based gas (H2S, SO 2 ,
NO2, Cl2 etc) is high, please take the conditions into ac -
count because the disconnection of chip resistor or bad
contact of contacts by the sulfurization may occur.
●For the
matching of structure, dimensions, lifespan, char -
acteristics and laws and regulations with the inst alling
equipment and parts, or the matching when the specifica -
tion of installing equipment is changed, please make the
final decision by the customer.
●We
cannot guarantee the use beyond the scope of speci -
fications of the product. Please use the product with great
care.
●A part may be partially
changed to improve the perfor -
mance.
●Do not
disassemble or remodel the product because it is
prohibited by the Radio Act.

－E30 －
－E31 －
Federal Communication Commission Interference Statement
●This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
●This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference
by one of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for
help.
●FCC Caution: Any changes or modifications not expressly
approved by the party responsible for compliance could void the
user's authority to operate this equipment.
●This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
●Radiation Exposure Statement:
The product comply with the FCC portable RF exposure limit set
forth for an uncontrolled environment and are safe for intended
operation as described in this manual. The further RF exposure
reduction can be achieved if the product can be kept as far as
possible from the user body or set the device to lower output
power if such function is available.

English
After-sales service
Repair .
• Consult to a dealer from whom you have purchased the
product for details of repair.
MEMO
Wh e n th e p ro d u ct i s i n co rp o ra te d to th e machi ne
or equipment you have purchased, consult to the
manufacturer or the dealer of the machine or equipment.
Technical information
• Technical information of this produ ct (Operating
Instructions, CAD data, Inquiries) can be dow nl o ade d
from the following web site.
https://industrial.panasonic.com/ww/products/motors-
compressors/fa-motors
■Convenient note (Write in for your inquiry or repair .)
Date of
purchase
Part No.
DV0PM20105
Purchase
store name
Phone: （）－
－E32 － IME98
Z1016-0

パナソニック株式会社 モータビジネスユニット
〒 574-0044 大阪府大東市諸福７丁目１番１号
電話（代表） [phone]
松下电器产业株式会社 马达经营单位
日本大阪府大东市诸福 7 丁目 1 番 1 号邮编 574-0044
电话 [phone]（总机）
Motor B u s i n e ss U n i t , P a n a s on i c C o r po r a t i on
7-1-1 Morofuku, Daito City, Osaka, 574-0044, Japan
Phone : [phone]
制造商 ：珠海松下马达有限公司
中国广东省珠海市南屏科技工业园屏东 3 路 3 号
原产地 ：中国
© Panasonic Corporation 2016
Printed in China
IME98
Z1016-0