Black & Decker BHFEA18 User manual

www.blackanddecker.com
3
5
7
8
6
4
21
9
10
11
12
12a
13
14
BHFEA18
BHFEA18D
Power connect cordless stick vac
Stik vakum nirkabel dengan power connect
 
Máy hút bụi cán không
dây kết nối nguồn
English 5
Bahasa Indonesia 11
 18
TIẾNG VIỆT 24

23
12a
12b
12
A B
3
C
7
7a
8F
12
12c
D
12
12d
12c
E

23
11 11a 7a
G
1
H
4
5
I
5
6
J
6
K
6 6a
L

4
M
N
13
O
9
9a
9b

5
ENGLISH
(Original instructions)
Intended use
Your BLACK+DECKER BHFEA18, BHFEA18D cordless
vacuum cleaner has been designed for vacuum cleaning
purposes. This appliance is intended for household use only.
Read all of this manual carefully
before operating the appliance.
Safety instructions
@Warning! Read all safety
warnings and all instructions.
Failure to follow the warnings
and instructions listed below may
result in electric shock, re and/or
serious injury.
uThe intended use is described in this
manual. The use of any accessory
or attachment or the performance
of any operation with this appliance
other than those recommended in this
instruction manual may present a risk
of personal injury.
uRetain this manual for future
reference.
uThis appliance contains batteries
that are only replaceable by skilled
persons.
Using your appliance
uDo not use the appliance to pick up liquids
or any materials that could catch re.
uDo not use without dust bag and/or
lters in place
uDo not use the appliance near water.
uDo not immerse the appliance in water.
uNever pull the charger lead to
disconnect the charger from the
socket.
Keep the charger lead away from heat,
oil and sharp edges.
uThis appliance can be used by
children aged from 8 years and above
and persons with reduced physical,
sensory or mental capabilities or
lack of experience and knowledge
if they have been given supervision
or instruction concerning use of
the appliance in a safe way and
understand the hazards involved.
Children shall not play with the
appliance. Cleaning and user
maintenance shall not be made by
children without supervision.
Inspection and repairs
Before use, check the appliance for
damaged or defective parts. Check for
breakage of parts, damage to switches
and any other conditions that may affect
its operation.
uDo not use the appliance if any part is
damaged or defective.
uHave any damaged or defective parts
repaired or replaced by an authorized
repair agent.
uRegularly check the charger lead for
damage. Replace the charger if the
lead is damaged or defective.
uNever attempt to remove or replace
any parts other than those specied in
this manual.
Additional safety instructions

6
ENGLISH (Original instructions)
After use
uUnplug the charger before cleaning the
charger or charging base.
uWhen not in use, the appliance should
be stored in a dry place.
uChildren should not have access to
stored appliances.
Residual risks
Additional residual risks may arise when
using the tool which may not be included
in the enclosed safety warnings. These
risks can arise from misuse, prolonged
use etc.
Even with the application of the relevant
safety regulations and the implementa-
tion of safety devices, certain residual
risks can not be avoided. These include:
uInjuries caused by touching any
rotating/moving parts.
uInjuries caused when changing any
parts, blades or accessories.
uInjuries caused by prolonged use
of a tool. When using any tool for
prolonged periods ensure you take
regular breaks.
uImpairment of hearing.
uHealth hazards caused by breathing
dust developed when using your
tool (example:- working with wood,
especially oak, beech and MDF.)
Batteries and chargers
Batteries (can be sold seperately)
uRechargeable batteries are to be
removed from the appliance before
being charged.
uBatteries are to be inserted with the
correct polarity.
uExhausted batteries are to be
removed from the appliance and safely
disposed of.
uIf the appliance is to be stored unused
for a long period, the batteries should
be removed.
uThe supply terminals are not to be
short circuited.
uNever attempt to open for any reason.
uDo not expose the battery to water.
uDo not expose the battery to heat.
uDo not store in locations where the
temperature may exceed 40°C.
uCharge only at ambient temperatures
between 10°C and 40°C.
uCharge only using the charger
provided with the appliance/tool.
Using the wrong charger could result
in an electric shock or overheating of
the battery.
uWhen disposing of batteries, follow
the instructions given in the section
“Protecting the environment”.
uDo not damage/deform the battery
pack either by puncture or impact, as
this may create a risk of injury and re.
uDo not charge damaged batteries.
uUnder extreme conditions, battery
leakage may occur. When you notice
liquid on the batteries carefully wipe
the liquid off using a cloth. Avoid skin
contact.
uIn case of skin or eye contact, follow
the instructions below.
Warning! The battery uid may cause
personal injury or damage to property.
In case of skin contact, immediately rinse

7
ENGLISH
(Original instructions)
with water. If redness, pain or irritation
occurs seek medical attention. In case of
eye contact, rinse immediately with clean
water and seek medical attention.
Chargers (can be sold seperately)
Your charger has been designed for a
specic voltage. Always check that the
mains voltage corresponds to the voltage
on the rating plate and the information in
the technical data table.
Warning! Never attempt to replace the
charger unit with a regular mains plug.
uUse your BLACK+DECKER charger
only to charge the battery in the
appliance/tool with which it was
supplied. Other batteries could burst,
causing personal injury and damage.
uNever attempt to charge
non-rechargeable batteries.
uIf the supply cord is damaged, it must
be replaced by the manufacturer or an
authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
uDo not expose the charger to water.
uDo not open the charger.
uDo not probe the charger.
uThe appliance/tool/battery must be
placed in a well ventilated area when
charging.
Electrical safety
Symbols on the charger
Read all of this manual carefully before using the
appliance.
#This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
$The charging base is intended for indoor use only.
Labels on appliance
The following symbols appear on this appliance along with the
date code
Read all of this manual carefully before
using the appliance
Features
This tool includes some or all of the following features.
1. On/off power button
2. Charging port
3. State of charge indicator
4. Dust bowl relase button
5. Clear dust bowl
6. Cyclonic lter assembly
7. Extension pole release button
8. Extension pole
9. Floorhead (with in-built oor sense)
10. Beater bar release button
11. Crevice tool
12. Battery
12a.Charger
13. Storage station
14. Wide mouth dust brush
Use
Charging the battery (Fig. A, B)
The standard charger provided will charge a fully depleted
battery in about 5 hours
uPlug the charger (12a) into an appropriate outlet before
inserting the battery pack (12).
uInsert the battery pack (12) into the charger (12a) as
shown in gure A.
uThe green LED (12b) will ash indicating that the battery
is being charged.
uThe completion of charge is indicated by the green
LED (12b) remaining on continuously. The pack is fully
charged and may be used at this time or left on the
charger.
Note: Recharge discharged batteries as soon as possible
after use or battery life may be greatly diminished.
Note: The charger and battery pack can be left connected
with the green LED glowing indenitely.
The charger will keep the battery pack fresh and fully charged.
Important charging notes
uLongest life and best performance can be obtained if
the battery pack is charged when the air temperature is

8
ENGLISH (Original instructions)
between 18°- 24°C. DO NOT charge the battery pack in
an air temperature below +4.5°C, or above +40.5°C.
This is important and will prevent serious damage to the
battery pack.
uThe charger and battery pack may become warm to touch
while charging. This is a normal condition, and does not
indicate a problem. To facilitate the cooling of the battery
pack after use, avoid placing the charger or battery pack
in a warm environment such as in a metal shed, or an
uninsulated trailer.
uIf the battery pack does not charge properly:
uCheck current at receptacle by plugging in a lamp or
other appliance.
uCheck to see if receptacle is connected to a light switch
which turns power off when you turn out the lights.
uMove charger and battery pack to a location where the
surrounding air temperature is approximately 18°-
24°C.
uIf charging problems persist, take the tool, battery pack.
and charger to your local service centre.
uThe battery pack should be recharged when it fails to
produce sufcient power on jobs which were easily done
previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may also
charge a partially used pack whenever you desire with no
adverse affect on the battery pack.
uForeign materials of a conductive nature such as, but not
limited to, steel wool, aluminium foil, or any buildup of
metallic particles should be kept away from charger
cavities.
Always unplug the charger from the power supply when
there is no battery pack in the cavity. Unplug charger
before attempting to clean.
uDo not freeze or immerse charger in water or any other
liquid.
Warning! Do not allow any liquid to get inside charger. Never
attempt to open the battery pack for any reason. If the plastic
housing of the battery pack breaks or cracks, return to a
service centre for recycling.
State of charge indicator (Fig. C)
This appliance include a state of charge indicator (3) which
consists of three LED lights that indicate the level of charge
remaining in the battery. This feature is only activated when
the vacuum is powered on and when the vacuum is on
charge.
The state of charge indicator is an indication of approximate
levels of charge remaining in the battery pack.
The LED battery indicator displays the remaining charge
and warns you when the battery is low.
The nal LED will ash continuously when there is only very
little runtime remaining.
Note: The state of charge indicator is only an indication
of the charge left on the battery.
It does not indicate tool functionality and is subject to variation
based on product components, temperature and end-user
application.
Installing and removing the battery (Fig. D, E)
Warning! Make certain the vac is switched off before
removing or installing battery.
To install battery pack
uInsert battery pack (12) into the vac (12c) until an audible
click is heard (Figure D). Make sure battery pack is fully
seated and fully latched into position.
To remove battery pack
uDepress the battery release button (12d) as shown in
Figure E and pull battery pack out of the vac.
Assembly (Fig. F)
uAlign the top of the extension tube (8) with the vacuum
inlet (7a) as shown in Fig. F.
uPush the extension tube (8) onto the vacuum inlet (7a) so
it locks into position.
uTo remove an the extension tube, press the extension
tube release button (7) and gently pull the extension tube
off.
Warning! When not in use position the unit with the rear of
the vacuum facing a wall so that any inadvertent fall of the unit
would contact a wall and not people or pets.
Useage
This vacuum cleaner can be used in one of two ways.
uWith the extension tube (8) and the oor head (9).
uWith the crevice tool (11) and the vacuum.
Mounting accessories (Fig. G)
uThe crevice tool (11) allows for vacuuming in narrow and
hard to-reach places.
uTo attach the crevice tool (11) press into vacuum inlet (7a)
so it locks into position as shown in gure G.
uTo release the crevice tool (11) press the crevice tool
release button (11a) and gently pull the extension tube off.
Switching ON and OFF (Fig. H)
uTo switch ON, push the on/off power button (1).
uFor increased power, push the On/Off button (1) again.
uPush the On/Off button (1) a third time to turn the unit off.
Note: The state of charge indicator LEDs (3) will illuminate
while the vacuum is ON.
uTo switch OFF, slide the on/off power switch (1) to the “O“
position.
uCharge the battery (12) immediately after use
so that it will be ready and fully charged for the next
use.

9
ENGLISH
(Original instructions)
Floorsense
Floorsense is active in the low speed. When a carpet is
detected, the performance of the unit is automatically
increased to high speed. When a hardoor is detected, the
performance of the unit reduces to low speed.
Cleaning and emptying the vacuum
Warning! Projectile/Respiratory Hazard: Never use the vac
without its filter.
Warning! The filter is re-usable, do not confuse it with a
disposable dust bag, and do not throw it away when the
product is emptied. We recommend that you replace the
filter every 6–9 months depending on frequency of use.
To empty the dust canister (Fig. I, J, K, L)
uPush down the dust canister release button (4) to
release and remove the dust canister (5) from the vacuum.
uUse your index nger and thumb to pinch the lter
housing tabs and pull the lter housing (6) from the
dust canister as shown in gure I.
uPlace the dust canister over a trash can and empty the
dust canister as illustrated in gure J.
uRemove the foam lter (6a) from the lter housing as
shown in gure K.
uShake or lightly brush any loose dust off of the foam
lter (6a) and lter (6).
uRinse out the dust canister (5) with warm soapy water.
uWash the lters with warm soapy water.
uEnsure the lters are completely dry before retting the
lters into the lter housing.
uRet the clean and dry foam lter (6a) into the lter
housing (6).
uInstall the lter housing into the dust canister (5).
uInstall the dust canister onto the vacuum, until it “clicks”
rmly into position.
Removing and cleaning the beater bar
(Fig. M, N)
Warning! To reduce the risk of injury from moving parts,
disconnect the oor head and extension tube from the vacuum
before cleaning or servicing.
uTo remove the beater bar (9b) from the oor head (9) Slide
the beater bar release button (9a) to the rear of the unit.
uThe beater bar (9b) can now be removed and cleaned.
Safe storage (Fig. O)
The unit can be safely stored, when not in use, by placing the
catch on the rear of the motor unit onto the storage station
(13) as shown in gure O.
Troubleshooting
Problem Possible Cause Possible Solution
Unit will not start. Battery not installed
properly.
Battery not charged.
Check battery
installation.
Check battery charging
requirements
Battery will not charge. Battery not inserted into
charger.
Charger not plugged in.
Surrounding air
temperature too hot or
too cold.
Insert battery into
charger
until LED appears.
Plug charger into a
working
outlet. Refer to
“Important
Charging Notes” for
more details.
Check current at
receptacle
by plugging in a lamp
or other appliance.
Check to see if
receptacle is
connected to a light
switch which turns
power off when you
turn out the lights
Move charger and tool
to a surrounding air
temperature of above
4,5°C or below
+40,5°C.
Maintenance
Your BLACK+DECKER cordless appliance has been designed
to operate over a long period of time with a minimum of main-
tenance. Continuous satisfactory operation depends upon
proper tool care and regular cleaning.
Warning! Before performing any maintenance on cordless
appliances:
uRun the battery down completely if it is integral and then
switch off.
uUnplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
uRegularly clean the ventilation slots in your appliance/
charger using a soft brush or dry cloth.
uRegularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
Replacing the lters
The lters should be replaced every 6 to 9 months and when-
ever worn or damaged. Replacement lters are available from
your BLACK+DECKER dealer.
uRemove the old lters as described above.
uFit the new lters as described above.
Protecting the environment
ZSeparate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.

10
ENGLISH (Original instructions)
Products and batteries contain materials that can be recov-
ered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com
Service Information
Black & Decker offers a full network of company-owned and
authorized service locations throughtout Asia. All Black &
Decker Service Centers are staffed with trained personnel to
provide customers with efcient and reliable product service.
Whether you need technical advice, repair, or genuine factory
replacement parts, contact the Black & Decker location
nearest to you.
Note
uBlack & Decker’s policy is one of continuous improvement
to our products and, as such, we reserve the right to
change product specications without prior notice.
uStandard equipment and accessories may vary by coun-
try.
uProduct specications may differ by country.
uComplete product range may not be available in all coun-
tries. Contact your local Black & Decker dealers for range
availability.
Technical Data
BHFEA18 BHFEA18D
Voltage 18V (20V Max) 18V (20V Max)
Watt Hours 36wh (18v 2.0ah
battery pack)
36wh (18v 2.0ah battery
pack)
Approx Charge Times 5 hours 5 hours
Weight 2.4kg bare unit - 2.8kg
with battery
2.4kg bare unit - 2.8kg
with battery
Charger SSC-250040EU
Input Voltage VAC 100 - 240
Output Voltage VDC 8 - 20
Current mA 400
Approx. charge time Hours 3 - 5
Battery BL1518 BL2018 BL4018
Voltage VAC 18V
(20V Max)
18V
(20V Max)
18V
(20V Max)
Capacity Ah 1.5 2.0 4.0
Type Li-Ion Li-Ion Li-Ion