Black Horce Model Fieseler FI156C Storch-EP User manual

Instruction Manual book
SPECIFICATION


Wingspan : 1,800 mm 70.87 in.


Length : 1,210 mm 47.64 in.


Weight : 2.1kg 4.62 Lbs.


Radio : 04 channels.


Servo : 06 servos.


Motor : KMS 2814/05


Battery : 3 Cells-Li-Poly-11.1V 3.200mAh


Speedcontrol :60A


Propeller : 12 x 6
MadeinVietnam.
ITEM CODE:BH 128

2
FIESELER FI156C STORCH - EP - Item code: BH128 . Instruction Manual
This instruction manual is designed to help you build a great flying aeroplane. Please read this
manualthoroughlybeforestartingassemblyofyourFIESELER FI156C STORCH - EP.Usethe
parts listing below to identify all parts.
WARNING.
Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is
capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU
ASSUME ALL RISK & RESPONSIBILITY.
IfyouareinexperiencedwithbasicR/CflightwestronglyrecommendyoucontactyourR/Csupplier
and join your local R/C Model Flying Club. R/C Model Flying Clubs offer a variety of training
proceduresdesignedtohelpthenewpilotonhisway tosuccessful R/Cflight. Theywill alsobeable
to advise on any insurance and safety regulations that may apply.
TOOLS & SUPPLIES NEEDED.
Thick cyanoacrylate glue.
30 minute epoxy.
5 minute epoxy.
Hand or electric drill.
Assorted drill bits.
Modellingknife.
Straight edge ruler.
2mm ball driver.
Phillips head screwdriver.
220 grit sandpaper.
90° square or builder’s triangle.
Wire cutters.
Masking tape & T-pins.
Thread-lock.
Paper towels.
Some more parts.
HARDWAREPACK
Landinggear.....
Toavoid scratching your new airplane, do not
unwrap the pieces until they are needed for
assembly. Cover your workbench with an old
towel or brown paper, both to protect the air-
craftand to protect the table. Keep a couple of
jars or bowls handy to hold the small parts af-
ter you open the bag.
PARTS LISTING.
FUSELAGE ASSEMBLY
(1) Fuselage.
WING ASSEMBLY
(1) Right wing half with pre-installed
aileron.
(1) Left wing half with pre-installed
aileron.
Tail section assembly
(1) Vertical stabilizer with pre-
installedrudder.
(1) Horizontal stabilizer with pre-
installedelevator halves.
SUGGESTION.
NOTE.
Pleasetrialfitalltheparts.Makesure youhave
the correct parts and that they fit and are
alignedproperly beforegluing!This will assure
proper assembly.FIESELER FI156C STORCH-EP
ARF ishandmade fromnatural materials,every
plane is unique and minor adjustments may
have to be made. However, you should find
the fit superior and assembly simple.
The painted and plastic parts used in this kit
are fuel proof. However, they are not tolerant
of many harsh chemicals including the follow-
ing:paintthinner,C/Aglueaccelerator,C/Aglue
debonderandacetone.Donot letthese chemi-
cals come in contact with the colors on the
covering and the plastic parts.

3
FIESELER FI156C STORCH - EP - Item code: BH128 . Instruction Manual
Caution: this model is not a toy!
Ifyou are a beginner to this type ofpowered model, please ask an experiencedmodel flyer for help
and support. If you attempt to operate the model without knowing what you are doing you could
easily injure yourself or somebody else. Please keep your safety and well-being in mind at all
times.
Important: before you start construction
Even if you have already built a large number of RC models please read right through these
instructions and check all the kit components against the parts list. We have taken great trouble to
keep construction as simple as possible, without making any compromises in the area of safety.
Note regarding the film covering
Minor creases or bubbles may develop in the film covering due to major fluctuations in weather
conditions (temperature, humidity etc.); in rare cases you may even find a slight warp in a
component. These minor faults are in the nature of film-covered built-up wooden structures, and
can easily be corrected using a heat gun, as commonly used for modelling.
Creases: Blow warm air over the area and rub down with a soft cloth.
Wing warp: Hold the panel twisted gently in the opposite direction to the warp, and apply
warm air to remove the creases from the covering.
Caution! do not heat the film more than is absolutely necessary. If the air or the iron is too hot, the
film may melt and holes may be formed.
This model is highly pre-fabricated and can be built in a very short time. However, the work which
youhave to carry out is importantand must be donecarefully.The model will onlybe strong and fly
well if you complete your tasks competently - so please work slowly and accurately.
When self-tapping screws have to be screwed into wood, apply a little white glue to prevent
them shaking loose: just squirt white glue into the hole and fit the screw.
SAFETY PRECAUTION.
+ This is not a toy
+ Be sure that no other flyers are using your radio frequency.
+ Wear safety glasses.
+ Keep loose clothing and wires away from the propeller.
+ Do not start the motor if people are near. Do not stand in line with the side of the propeller.
+ Make motor adjustments from behind the propeller only. Do not reach around the spinning propel-
ler.

4
FIESELER FI156C STORCH - EP - Item code: BH128 . Instruction Manual
REPLACEMENT LARGE PARTS
B. Wing panel.
A. Fuselage.
C. Horizontal stabilizer.
E. Aluminium wing dihedral brace.
D. Rudder.
F. Decal sheet.
REPLACEMENT SMALL PARTS
7.Plasticparts bottomfuselage.
4.
3. Wheels
2.Wing strutsset.
1.Landing gearstruts.
6.Tailgear set.
5.Vertical stabilizerstruts.
8.Plastic partsfor pushrod.
9.Ruler
1.
4.
3.
5. 6. 8.
7.
9.
3x10mm.
2.
1a.
1b.
1c.
2b.
2a.
A.
B. B.
C. D.
E.
C.
F.

5
FIESELER FI156C STORCH - EP - Item code: BH128 . Instruction Manual
1) Install the rubber grommets and brass
eyelets onto the aileron servos.
I. AILERON.
1.INSTALLING THE AILERON SERVOS.
Top side
2)Using a modeling knife, remove the cov-
ering at possition show below.
Aileron
Secure.
3) Using the thread as a guide and using
masking tape, tape the servo lead to the end
of the thread: carefully pull the thread out.
When you have pulled the servo lead out, re-
move the masking tape and the servo lead
from the thread.
4)Drill 1,6mm pilot holes through the block
of wood for each of the four mounting screws
provided with the servo.
5. Instal servo tray with aileron servo into
the wing as same as picture below.
Remove
covering.
Bottom side
Aileron.
Flap.
Electric wire.
thread

6
FIESELER FI156C STORCH - EP - Item code: BH128 . Instruction Manual
Repeat the procedure for the other wing
half.
INSTALLINGTHEAILERON CONTROLHORN.
Aileroncontrolhorn
A+B Epoxy
PLUS glue
AB
2x10mm.
A+B Epoxy
PLUS glue
Aileron
control horn.
Ruler
Secure.
Top side.

7
FIESELER FI156C STORCH - EP - Item code: BH128 . Instruction Manual
Installing the aileron linkages as pictures
below.
INSTALLING THE AILERON
LINKAGES.
Repeat the procedure for the other wing
half.
M2 M2 lock nut
75 mm.
1.INSTALLING THE FLAP SERVO.
II - FLAP.
2x10mm.
Secure.
2.INSTALLING THE FLAP
CONTROL HORN.
ControlhornofFlap.
Electric wire.
thread
Bottom side.
A+B EPOXY
PLUS glue

8
FIESELER FI156C STORCH - EP - Item code: BH128 . Instruction Manual
Controlhorn
of Flap.
3.INSTALLING THE FLAP
LINKAGES .
M2 M2 lock nut
75 mm.
Installing the flap linkages as pictures
below.
Repeat the procedure for the other wing
half.
3x 10mm
See pictures below:
INSTALLING ELECTRIC MOTOR.
Front view.
Ruler
Top side.
Bottom side.
Flap.
Aileron.
Bottom side.

9
FIESELER FI156C STORCH - EP - Item code: BH128 . Instruction Manual
Secure
Tie wrap.
INSTALLING THE BATTERY.
Push in to.
Battery.
PARTSREQUIRED
Front view.
Secure.
INSTALLING LANDING GEAR.

10
FIESELER FI156C STORCH - EP - Item code: BH128 . Instruction Manual
Bend.
A+B Epoxy Plus
glue.
Bottom side.
A+B Epoxy
Plus glue.

11
FIESELER FI156C STORCH - EP - Item code: BH128 . Instruction Manual
Push.
Bottom side.
Right side.
Bend.
Bend.
Left side.

12
FIESELER FI156C STORCH - EP - Item code: BH128 . Instruction Manual
1. Install the rubber grommets and brass
colletsintothe elevatorservo.Testfitthe servo
into the servo tray.
2. Mount the servo to the tray using the
mountingscrews provided withyourradio sys-
tem.
SERVO ELEVATOR AND RUDDER
Elevator servo.
A+B EPOXY
PLUS glue.
Secure.
Repeat the procedure for the right side
landing gear
Secure.
Bottom side.

13
FIESELER FI156C STORCH - EP - Item code: BH128 . Instruction Manual
Horizontalstabilizeinstallation .
See picture below.
HORIZONTALSTABILIZER
INSTALLATION.
Push in to.
75mm
Epoxy
glue.
143mm
aluminium tube 8mm

14
FIESELER FI156C STORCH - EP - Item code: BH128 . Instruction Manual
Epoxyglue.
C/Aglue.
Top side.
C/Aglue.
C/Aglue.
C/Aglue.
A+B Epoxy
PLUSglue.

15
FIESELER FI156C STORCH - EP - Item code: BH128 . Instruction Manual
Elevator control horn install as same as the
way of aileron control horn. Please see pic-
tures below.
ControlhornofElevator.
ELEVATOR CONTROL HORN INSTALLA-
TION.
Top side.
Bottom side.
A+B Epoxy
PLUSglue.
 Elevatorpushrod install as same as the way
of aileron pushrod.
ELEVATOR PUSHROD INSTALLATION.
M2 M2 lock nut.
Controlhorn
ofElevator.
C/Aglue.

16
FIESELER FI156C STORCH - EP - Item code: BH128 . Instruction Manual
Rudder servo install as same as method of
elevator servo. See picture below:
Push.
C/Aglue.
Rudder servo.
C/Aglue.
Top side.
Elevatorpushrod
M2 M2 lock nut.
RUDDER THE INSTALLATION.

17
FIESELER FI156C STORCH - EP - Item code: BH128 . Instruction Manual
A+ B Epoxy
Plus glue.
Ruddercontrol
horn.
ControlhornofRudder.
Rudder control horn install as same as the
way of aileron control horn. Please see pic-
tures below.
RUDDER CONTROL HORN INSTALLA-
TION.  Rudder pushrod install as same as the way
of aileron pushrod.
RUDDER PUSHROD INSTALLATION.
Rudder
pushrod.
M 2 M2 lock nut.
Elevatorpushrod
Rudder
pushrod.

18
FIESELER FI156C STORCH - EP - Item code: BH128 . Instruction Manual
Cut.
C/Aglue
Bottom side Elevator
pushrod
Rudder
pushrod.
MOUNTING THE TAIL WHEEL
BRACKET.


1. Set the tail wheel assembly in place
on the plywood plate. The pivot point of the
tail wheel wire should be even with the rud-
derhingelineand thetail wheelbracketshould
be centered on the plywood plate.


2. Using a pen, mark the locations of the
two mounting screws. Remove the tail wheel
bracket and drill 1mm pilot holes at the loca-
tions marked.
Markpoint.
Plastic parts of pushrod.
3x 12mm

19
FIESELER FI156C STORCH - EP - Item code: BH128 . Instruction Manual
Bottom side.
Vertical Stabilizer Struts.
Secure.
3x 10mm
3x10mm 3x10mm


3. Secure the tail wheel bracket in place
using three 3mm x 12mm wood screws. Be
careful not to overtighten the screws.
Secure.
3x 12mm
Top side.
Secure.

20
FIESELER FI156C STORCH - EP - Item code: BH128 . Instruction Manual
Rightside.
Do not permanently secure the receiver and
battery until after balancing the model.


3. Position the battery pack and receiver
is as pictures below.


1. Plug the servo leads and the switch
leadinto the receiver. You may want to plug
anaileronextensioninto the receiver to make
plugging in the aileron servo lead easier
when you are installing the wing . Plug the
battery pack lead into the switch.


2. Wrap the receiver and battery pack in
the protective foam to protect them from vi-
bration.Usearubber band or masking tape to
hold the foam in place.
Receiver.
INSTALLINGTHE RECEIVERAND BATTERY.
Locatethealuminiumwingdihedralbrace.
*** Test fit the aluminium tube dihedral brace
into each wing haft. The brace should slide in
easily. If not, use 220 grit sand around the
edges and ends of the brace until it fits prop-
erly.
WINGATTACHMENT.
482mm
12mm Aluminium tube.
Left side.
Bottom side
Topside


4) Usinga 2mm drill bit, drilla hole through
the side of the fuselage, near the receiver, for
the antenna to exit.