Black Horce Model P-36A Hawk Owner's manual

Made in Vietnam.
SPECIFICATION
 Wingspan : 1,600 mm 63.in.
 Length : 1,300 mm 52.in.
 Weight : 3.9 kg 8.58 lbs.
Engine : 61 cu.in-2stroke.
15 CC Gas
 Servo : : 8 Servos + 2 servos Retract (HITEC HS-75BB)
Radio : 8 channels.
Instruction Manual book
ITEM CODE: BH41

P- 36A HAWK-Item code BH41. INSTRUCTION MANUAL.
2
This instruction manual is designed to help you build a great flying aeroplane. Please read this
manual thoroughly before starting assembly of your P- 36A HAWK. Use the parts listing below to
identify all parts.
WARNING.WARNING.
WARNING.WARNING.
WARNING.
Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is
capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU
ASSUME ALL RISK & RESPONSIBILITY.
If you are inexperienced with basic R/C flight we strongly recommend you contact your R/C
supplier and join your local R/C Model Flying Club. R/C Model Flying Clubs offer a variety of training
procedures designed to help the new pilot on his way to successful R/C flight. They will also be able
to advise on any insurance and safety regulations that may apply.
TOOLS & SUPPLIES NEEDED.
Thick cyanoacrylate glue.
30 minute epoxy.
5 minute epoxy.
Hand or electric drill.
Assorted drill bits.
Modelling knife.
Straight edge ruler.
2mm ball driver.
Phillips head screwdriver.
220 grit sandpaper.
90° square or builder’s triangle.
Wire cutters.
Masking tape & T-pins.
Thread-lock.
Paper towels.
Some more parts.
HARDWAREPACK
COWLING.
Landing gear.....
To avoid scratching your new airplane, do
not unwrap the pieces until they are needed
for assembly. Cover your workbench with an
old towel or brown paper, both to protect the
aircraft and to protect the table. Keep a couple
of jars or bowls handy to hold the small parts
after you open the bag.
Please trial fit all the parts. Make sure you
have the correct parts and that they fit and are
aligned properly before gluing! This will assure
proper assembly. P- 36A HAWK ARF is hand
made from natural materials, every plane is
unique and minor adjustments may have to
be made. However , you should find the fit
superior and assembly simple.
The painted and plastic parts used in this kit
are fuel proof. However, they are not tolerant
of many harsh chemicals including the
following: paint thinner, C/A glue accelerator,
C/A glue debonder and acetone. Do not let
these chemicals come in contact with the
colors on the covering and the plastic parts.
PARTS LISTING.
FUSELAGE ASSEMBLY
(1) Fuselage.
WING ASSEMBLY
(1) Right wing half with pre-installed
aileron.
(1) Left wing half with pre-installed
aileron.
Some more parts........
Tail section assembly
(1) Vertical stabilizer with pre-
installed rudder.
(1) Horizontal stabilizer with pre-
installed elevator halves.
SUGGESTION.
NOTE.

3
P- 36A HAWK-Item code BH41. INSTRUCTION MANUAL.
+ This is not a toy
+ Be sure that no other flyers are using your radio frequency.
+ Do not smoke near fuel.
+ Store fuel in a cool, dry place, away from children and pets.
+ Wear safety glasses.
+The glow plug clip must be securely attached to the glow plug.
+ Do not flip the propeller with your fingers.
+ Keep loose clothing and wires away from the propeller.
+ Do not start the engine if people are near. Do not stand in line with the side of the propeller.
+ Make engine adjustments from behind the propeller only. Do not reach around the spinning pro-
peller.
SAFETY PRECAUTION.
REPLACEMENT LARGE PARTS
B. Wing panel(Right&Left).
A. Cowling.
C. Fuselage.
D . Horizontal stabilizer(Right&Left).
F. Aluminium wing dihedral brace.
E. Rudder.
G. Decal sheet.
B.
C.
B.
D.
D.
E.
F.
A.
G.

P- 36A HAWK-Item code BH41. INSTRUCTION MANUAL.
4
REPLACEMENT SMALL PARTS
3.Wheels.
5. Tail gear set.
2.Retract main gear(Right&Left).
4. Fuel tank.
1.Door mounting wheel.
1) Install the rubber grommets and brass
eyelets onto the aileron servos.
1.INSTALLING THE AILERON SERVOS.
I. AILERON.
6. Plastic parts for elevator and rudder
pushrod.
7. Plastic part for tail gear.
8.Tile wrap
2.
1. 1.
3.
2.
4.
5.
6.
7.
8.
3 x 10mm.
3 x 10mm.
Aileron.
Flap.
Aileron.

5
P- 36A HAWK-Item code BH41. INSTRUCTION MANUAL.
2) Using the thread as a guide and using
masking tape, tape the servo lead to the end
of the thread: carefully pull the thread out.
When you have pulled the servo lead out, re-
move the masking tape and the servo lead
from the thread.
3) Drill 1,6mm pilot holes through the block
of wood for each of the four mounting screws
provided with the servo.
4. Instal servo tray with aileron servo into
the wing as same as picture below.
Repeat the procedure for the other wing
half.
2.INSTALLING THEAILERON CONTROLHORN
.
3 x 20 mm.
C/A glue.
C/A glue.
C/A glue.
Thread.
Electric wire
Secure
Bottom side
C/A glue.

P- 36A HAWK-Item code BH41. INSTRUCTION MANUAL.
6
Install aileron control horn as same as
picture below.
Repeat the procedure for the other wing
half.
Aileron
control horn.
INSTALLING THE AILERON
LINKAGES.
2 x 8mm
2 x 8mm
2x8mm.
58 mm.
Repeat the procedure for the other wing
half.
Aileron
control horn.
Secure.
Secure.

7
P- 36A HAWK-Item code BH41. INSTRUCTION MANUAL.
II. FLAP.
1.INSTALLING THE FLAP SERVOS.
2.INSTALLING THE FLAP CONTROL HORN.
3 x 15 mm.
Secure.
Secure.
Thread
Electric
wire
Flap control
horn.
C/A glue.
C/A glue.
Bottom of wing.
C/A glue.

P- 36A HAWK-Item code BH41. INSTRUCTION MANUAL.
8
Installing the aileron linkages as pictures
below.
3. INSTALLING THE FLAP
LINKAGES.
Repeat the procedure for the other wing
half.
bottom of wing.
Flap
Aileron
INSTALLING RETRACTABLE
LANDING GEAR.
2 x 8mm
2x8mm.
58 mm.
Secure.
2 x 8mm.
3 x 15mm. 3 x 15mm.
C/A glue.

9
P- 36A HAWK-Item code BH41. INSTRUCTION MANUAL.
Mark point.
Mark point.
Drill a hole
2mm diameter
Secure.
Secure.
3 x 15mm.

P- 36A HAWK-Item code BH41. INSTRUCTION MANUAL.
10
connector.
Push.
Secure.
Secure.
Servo for retractable only.

11
P- 36A HAWK-Item code BH41. INSTRUCTION MANUAL.
Trim and cut.
Remove
covering.
Drill a hole 2mm
diameter
Drill a hole 2mm
diameter
Secure.
Secure.
3 x 10mm.
3 x 10mm.

P- 36A HAWK-Item code BH41. INSTRUCTION MANUAL.
12
Repeat the procedure for the other wing
half.
See pictures below:
INSTALLING THE ENGINE MOUNT.
Drill a hole
5.2mm diameter
Bottom side.
INSTALLING THE ENGINE.
5 x30mm.

13
P- 36A HAWK-Item code BH41. INSTRUCTION MANUAL.
Secure.
1. Install one adjustable metal connector
through the third hole out from the center of
one servo arm, enlarge the hole in the servo
arm using a 2mm drill bit to accommodate the
servo connector. Remove the excess mate-
rial from the arm.
After installing the adjustable metal con-
nector apply a small drop of thin C/A to
the bottom nut. This will prevent the con-
nector from loosening during flight.
INSTALLING THE THROTTLE - CABLE.
Throttle servo
INSTALLING THE STOPPER ASSEMBLY
FUEL TANK.
Throttle servo
Throttle cable
Tygon gas tubing
not included.

P- 36A HAWK-Item code BH41. INSTRUCTION MANUAL.
14
5. Test fit the stopper assembly into the
tank. It may be necessary to remove some of
the flashing around the tank opening using
a modeling knife. If flashing is present, make
sure none of it falls into the tank.
6. When satisfied with the alignment of the
stopper assembly tighten the 3mm x 20mm
machine screw until the rubber stopper
expands and seals the tank opening. Do not
over tighten the assembly as this could cause
the tank to split.
7. Using a modeling knife, cut 3 lengths of
fuel line 150mm long. Connect 2 lines to the 2
vent tubes and 1 line to the fuel pickup tube in
the stopper.
Vent tube Fuel pick- up tube
Fuel fill tube
When the stopper assembly is installed
in the tank, the top of the vent tube should
rest just below the top surface of the tank.
It should not touch the top of the tank.
1. The stopper has been pre-assembled at
the factory.
2. Using a modeling knife, cut one length of
silicon fuel line (the length of silicon fuel line is
calculated by how the weighted clunk should
rest about 8mm away from the rear of the tank
and move freely inside the tank). Connect one
end of the line to the weighted clunk and the
other end to the nylon pick up tube in the
stopper.
3. Carefully bend the second nylon tube up
at a 45 degree angle (using a cigarette lighter).
This tube will be the vent tube to the muffler.
4. Carefully bend the third nylon tube down
at a 45 degree angle (using a cigarette lighter).
This tube will be vent tube to the fueling valve.
8. Feed three lines through the fuel tank
compartment and through the pre-drilled hole
in the firewall. Pull the lines out from behind
the engine, while guiding the fuel tank into
place. Push the fuel tank as far forward as
possible, the front of the tank should just about
touch the back of the firewall.
Blow through one of the lines to ensure
the fuel lines have not become kinked inside
the fuel t ank comp artment. Air should flow
through easily.
9. To secure the fuel tank in place, apply a
bead of silicon sealer to the forward area of
the tank, where it exits the fuselage behind the
engine mounting box and to the rear of the tank
at the forward bulkhead.

15
P- 36A HAWK-Item code BH41. INSTRUCTION MANUAL.
Do not secure the tank into place
permanently until after balancing the
airplane. You may need to remove the tank
to mount the battery in the fuel tank
compartment.
Tie wrap.
COWLING.
Fuel tank.
See pictures below:

P- 36A HAWK-Item code BH41. INSTRUCTION MANUAL.
16
center 1.
Mark point 1.
Mark point 2.
Mark point 3.
Trim and cut.
center 2.
Center 3.

17
P- 36A HAWK-Item code BH41. INSTRUCTION MANUAL.
2. While keeping the back edge of the
cowl flush with the marks, align the front of
the cowl with the crankshaft of the engine. The
front of the cowl should be positioned so the
crankshaft is in nearly the middle of the cowl
opening. Hold the cowl firmly in place using
pieces of masking tape.
4. Install the muffler and muffler extension
onto the engine and make the cutout in the
cowl for muffler clearance. Connect the fuel
and pressure lines to the carburetor , muffler
and fuel filler valve.
3. Slide the cowl back over the engine
and secure it in place using four wood screws.
See picture below.
1) Slide the fiberglass cowl over the en-
gine and line up the back edge of the cowl with
the marks you made on the fuselage.
Secure.
Drill a hole
2mm diameter
Secure.
3x 12mm.

P- 36A HAWK-Item code BH41. INSTRUCTION MANUAL.
18
C/A glue.
142 mm
9 mm
Aluminium brace.
Aluminium
brace.
C/A glue.
C/A glue.
C/A glue.
See pictures below:
HORIZONTAL STABILIZER.
Elevator servo.
Elevator servo.
ELEVATOR INSTALLING
SERVOS.

19
P- 36A HAWK-Item code BH41. INSTRUCTION MANUAL.
Secure.
Elevator
Control horn.
Bottom side
EVATOR PUSHROD INSTALLATION.
 Elevator pushrod install as same as the way
of aileron pushrod.
2 x8mm
ELEVATOR CONTROL HORN INSTALLA-
TION.
Elevator control horn install as same as the
way of aileron control horn. Please see pic-
tures below.
3 x 20 mm.
Bottom side.
C/A glue.
Epoxy glue

P- 36A HAWK-Item code BH41. INSTRUCTION MANUAL.
20
C/A glue.
Elevator
pushrod.
Plastic parts of elevator and
rudder pushrod.
Cut
Secure.
2 x8mm
Secure.
Bottom side.
Elevator
pushrod
Elevator
pushrod
Secure.