Black Stone 1566 User manual

1-AA Battery required for ignitor (not included)
FOR OUTDOOR USE ONLY
! !
WARNING
Please read manual carefully before assembly
Retain this manual for future reference
36” GIDE
COIG SAIN
Owner’s Manual
MODEL 1566
North Atlantic Imports LLC | 513 West 2500 North, North Logan UT 84341 | www.blackstoneproducts.com

www.blackstoneproducts.com
2
WARNING:
Before proceeding, make certain that you understand the IMPORTANT INFORMATION section of
this manual.
Hazardous re or explosion may result if instructions are ignored.
It is the consumer’s responsibility to see that the griddle is properly assembled, installed, and
maintained. Failure to follow the instructions in this manual could result in bodily injury and/or property
damage.
FOR YOUR SAFETY IF YOU SMELL GAS:
1. Turn off gas supply at tank.
2. Extinguish all open ames; do not operate any electrical appliances.
3. Ventilate the area.
4. Check for leaks as detailed in this manual.
PRECAUTIONS:
1. Leak test all connections after each tank rell.
2. Never check for leaks with a match or open ame.
3. Do not store gasoline or other ammable vapors and liquids in the vicinity of this or any
other appliance.
4. Any LP cylinder not connected for use shall not be stored in the vicinity of this or any
other appliance.
5. Do not store a spare LP-gas cylinder under or near this appliance.
6. Never ll the cylinder beyond 80 percent full.
7. If the information in the above two statements is not followed exactly, a re causing death or
serious injury may occur.
8. Do not operate grill any closer than 36 inches from any combustible construction, including walls
and ceilings.
9. Do not use this appliance under overhead combustible surfaces.
10. The regulator used in this unit is ZHENDAR T3. If this regulator fails, it must be replaced with the
exact model and must only be replaced by a professionally licensed, authorized dealer.
DANGER
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open ame.
3. If odor continues, keep away from the appliance
and immediately call your gas supplier or your
re department.
WARNING
1. Do not store or use gasoline or other ammable
liquids or vapors in the vicinity of this or any
other appliance.
2. An LP cylinder not connected for use shall not be
stored in the vicinity of this or any
other appliance.
! !

3
! !
DANGER
! !
DANGER
! !
WARNING
! !
WARNING
! !
CAUTION
! !
CAUTION
! !
CAUTION
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open ame.
3. If odor continues, keep away from the appliance
and immediately call your gas supplier or your
re department.
DANGER: Indicates an imminently hazardous
situation which, if not avoided, will result in death or
serious injury.
1. Do not store or use gasoline or other ammable
liquids or vapors in the vicinity of this or any
other appliance.
2. An LP Tank not connected for use shall not be
stored in the vicinity of this or any
other appliance.
WARNING: Be alert to the possibility of serious
bodily injury if the instructions are not followed.
Be sure to read and carefully follow all of
the messages.
Some parts may contain sharp edges, especially as
noted in these instructions.
Wear protective gloves if necessary.
CAUTION: Indicates a potentially hazardous
situation which,if not avoided, may result in minor or
moderate injury.
For residential use only. Do not use for
commercial cooking.
Model Number ________________________
Serial Number _________________________
Date Purchased _______________________
To Installer/Assembler: Leave these instructions with
consumer.
To Consumer: Keep this manual for future reference.
Call the BLACKSTONE Patio Oven Information
Center for Help and Parts
Missing Parts? Assembly Questions? Operation Problems?
Before returning Patio Oven to store, call:
USA [phone] | Canada [phone]
or email us at [email protected]
Installation Safety Precautions
• Use griddle, as purchased, only with LP (propane)
gas and the regulator/valve assembly supplied.
• Griddle installation must conform with local codes,
or in the absence of local codes, with either the
National Fuel Gas Code, ANSI Z223.1/ NFPA 54,
Natural Gas and Propane Installation Code, CSA
B149.1, or Propane Storage and Handling Code,
B149.2, or the Standard for Recreational Vehicles,
ANSI A 119.2/NFPA 1192, and CSA Z240 RV
Series, Recreational Vehicle Code, as applicable.
• Griddle is not for use in or on recreational vehicles
and/or boats.
• This griddle is safety certied for use in the United
States and/or Canada only. Do not modify for use
in any other location. Modication will result in a
safety hazard.
Safety Symbols
The symbols and boxes shown below explain what
each heading means. Read and follow all of the
messages found throughout the manual.

www.blackstoneproducts.com
4
TABLE OF CONTENTS
FOR YOUR SAFETY.............................. 2-3
USE AND CARE.................................. 5-11
ILLUSTRATED PARTS LIST................... 12
HARDWARE........................................... 13
ASSEMBLY........................................ 14-18
CARE AND MAINTENANCE.................. 19
WARRANTY............................................ 20
GRIDDLE CARE & SEASONING...... 21-22
CUSTOMER SERVICE........................... 23
REORDERING PARTS........................... 23
CONTACT INFO..................................... 23

5
! !
DANGER
• NEVER store a spare LP cylinder under or near the
appliance or in an enclosed area.
• Never ll a cylinder beyond 80% full.
• If the information in the two points above is not fol-
lowed exactly, a re causing death or serious injury
may occur.
• An overlled or improperly stored cylinder is a
hazard due to possible gas release from the safety
relief valve. This could cause an intense re with
risk of property damage, serious injury or death.
• If you see, smell or hear gas escaping,
immediately get away from the LP cylinder and
appliance and call your re department.
LP Tank Removal, Transport And Storage
• Turn OFF all control knobs and LP tank valve. Turn
coupling nut counterclockwise by hand
only - do not use tools to disconnect. Lift LP tank wire
upward off of LP tank collar, then lift LP tank up and
off of support bracket. Install safety cap onto LP tank
valve. Always use cap and strap supplied with valve.
Failure to use safety cap as directed may result in serious
personal injury and/or property damage.
• A disconnected LP tank in storage or being trans-
ported must have a safety cap installed (as shown).
Do not store an LP tank in enclosed spaces such as a
carport, garage, porch, covered patio or other build-
ing. Never leave an LP tank inside a vehicle which
may become overheated by the sun.
• Do not store an LP tank in an area where
children play.
LP Tank
• The LP Tank used with your grill must meet the following
requirements:
• LP Tanks must be constructed and marked in ac-
cordance with specications for LP Tanks of the U.S.
Department of Transportation (DOT) or for Canada,
CAN/CSA-B339, tanks, spheres and tubes for
transportation of dangerous goods. Transport
Canada (TC). See LP Tank collar for marking.
• LP Tank valve must have:
• Type 1 outlet compatible with regulator or grill.
• Safety relief valve.
• UL listed Overll Protection Device (OPD). This OPD
safety feature is identied by a unique triangular
hand wheel. Use only LP Tanks
equipped with this type of valve.
• LP Tank must be arranged for
vapor withdrawal and include
collar to protect LP Tank valve.
Always keep LP Tanks in upright
position during use, transit
or storage.
LP Tank in upright position for vapor withdrawal
LP (Liqueed Petroleum Gas)
• LP gas is nontoxic, odorless and colorless when
produced.
• For Your Safety, LP gas has been given an odor
(similar to rotten cabbage) so that it can be smelled.
• LP gas is highly ammable and may ignite
unexpectedly when mixed with air.
LP Tank Filling
• Use only licensed and experienced dealers.
• LP dealer must purge new tank before lling.
• Dealer should NEVER ll LP Tank more than 80% of
LP Tank volume. Volume of propane in tank will vary
by temperature.
• A frosty regulator indicates gas overll. Immediately
close LP Tank valve and call local LP gas dealer for
assistance.
• Do not release liquid propane (LP) gas into the
atmosphere. This is a hazardous practice.
• To remove gas from LP Tank, contact an LP dealer
or call a local re department for assistance. Check
the telephone directory under “Gas Companies” for
nearest certied LP dealers.

www.blackstoneproducts.com
6
If “growing” bubbles appear do not use or move the LP
tank. Contact an LP gas supplier or your
re department!
LP Tank Exchange
• Many retailers that sell grills offer you the option of
replacing your empty LP tank through an exchange
service. Use only those reputable exchange companies
that inspect, precision ll, test and certify their tanks.
Exchange your tank only for an OPD safety
feature-equipped tank as described in the “LP Tank”
section of this manual.
• Always keep new and exchanged LP tanks in upright
position during use, transit or storage.
• Leak test new and exchanged LP tanks BEFORE
connecting to grill.
• Place dust cap on cylinder valve outlet whenever the
cylinder is not in use. Only install the type of dust cap on
the cylinder valve outlet that is provided with the cylinder
valve. Other types of caps or plugs may result in leakage
of propane.
LP Tank Leak Test
For your safety
• Leak test must be repeated each time LP tank is
exchanged or relled.
• Do not smoke during leak test.
• Do not use an open ame to check for gas leaks.
• Griddle must be leak tested outdoors in a
well-ventilated area, away from ignition sources such
as gas red or electrical appliances. During leak test,
keep griddle away from open ames or sparks.
• Use a clean paintbrush and a 50/50 mild soap and
water solution. Brush soapy solution onto areas
indicated by arrows in gure below. Leaks are
indicated by growing bubbles.
Connecting Regulator To The LP Tank
1. LP tank must be properly secured onto griddle.
(Refer to assembly section.)
2. Turn all control knobs to the OFF position.
3. Turn LP tank OFF by turning OPD hand wheel
clockwise to a full stop.
4. Remove the protective cap from LP tank valve.
Always use cap and strap supplied with valve.
Do not insert a POL transport
plug (plastic part with external
threads) into the Type 1 tank
valve outlet. It will defeat the
Safety Relief Valve feature.
5. Hold regulator and insert
nipple into LP tank valve.
Hand-tighten the coupling nut,
holding regulator in a straight line
with LP tank valve so as not to
cross thread the connection.
Do not use household cleaning agents. Damage
to gas valve/hose/regulator components can result.
! !
WARNING

7
6. Turn the coupling nut clockwise and tighten to a full
stop. The regulator will seal on the back-check feature in
the LP tank valve, resulting in some resistance. An
additional one-half to three-quarters turn is
required to complete the connection. Tighten by
hand only – do not use tools.
NOTE:
If you cannot complete the connection, disconnect
regulator and repeat steps 5 and 6. If you are still unable
to complete the connection, do not use this regulator!
Call [phone] for identical replacement parts.
Leak Testing Valves, Hose and Regulator
1. Turn all griddle control knobs to OFF.
2. Be sure regulator is tightly connected to
LP tank.
3. Completely open LP tank valve by turning OPD
hand wheel counterclockwise. If you hear a
rushing sound, turn gas off immediately. There
is a major leak at the connection. Correct
before proceeding by calling for replacement
parts at [phone].
4. Brush soapy solution onto areas where bubbles
are shown in picture below:
5. If “growing” bubbles appear, there is a leak.
Close LP tank valve immediately and retighten
connections. If leaks cannot be stopped
do not try to repair. Call for replacement
parts at [phone].
6. Always close LP tank valve after performing
leak test by turning hand wheel clockwise.
! !
DANGER
• Do not insert any tool or foreign objects into the
valve outlet or safety relief valve. You may
damage the valve and cause a leak. Leaking
propane may result in explosion, re, severe
personal injury, or death.
• If a leak is detected at any time, STOP and call
the re department.
• If you cannot stop a gas leak, immediately close
LP tank valve and call LP gas supplier or your
re department!
• Never attempt to attach this grill to the
self-contained LP gas system of a camper trailer
or motor home.
• Do not use grill until leak-tested.
! !
WARNING

www.blackstoneproducts.com
8
Safety Tips
1. Before opening LP cylinder valve, check the coupling nut for tightness.
2. When griddle is not in use, turn off all control knobs and LP cylinder valve.
3. Never move griddle while in operation or still hot.
4. Use long-handled barbecue utensils and oven mitts to avoid burns and splatters.
5. Maximum on side shelf is 10 lbs.
6. The grease tray must be inserted into griddle and emptied after each use. Do not remove grease tray until
grill has completely cooled.
7. Clean griddle often, preferably after each cookout. If a bristle brush is used to clean any of the grill cooking
surfaces, ensure no loose bristles remain on cooking surfaces prior to grilling.
8. If you notice grease or other hot material dripping from grill onto valve, hose or regulator, turn off gas
supply at once. Determine the cause, correct it, then clean and inspect valve, hose and regulator before
continuing. Perform a leak test.
9. Keep ventilation openings in cylinder enclosure (grill cart) free and clear of debris.
10. The regulator may make a humming or whistling noise during operation. This will not affect safety or use
of griddle.
11. If you have a griddle problem see the “Troubleshooting Section”.
12. If the regulator frosts, turn off griddle and LP cylinder valve immediately. This indicates a problem with the
cylinder and it should not be used on any product. Return to supplier!

9
! !
CAUTION
• Do not use water on a grease re. Personal
injury may result. If a grease re develops,
turn knobs and LP cylinder off.
• Do not leave grill unattended while
preheating or burning off food residue on
HI. If grill has not been regularly cleaned, a
grease re can occur that may damage
the product.
Ignitor Lighting the Griddle
Do not lean over grill while lighting.
1. In order for the igniter switch to work,
please make sure the battery is properly
installed.
2. Turn OFF gas burner control valves.
3. Turn ON gas at LP cylinder.
4. To ignite, push and turn the IGNITION
BURNER knob to MAX.
5. Push and hold ELECTRONIC IGNITION
button until the IGNITION BURNER lights.
6. If ignition does NOT occur in 5 seconds, turn
the burner controls OFF, wait 5 minutes and
repeat the lighting procedure.
7. To ignite remaining burners, turn each
burner knob in sequence to the position,
starting with the burner closest to the
IGNITION BURNER.
8. Once each burner has ignited, turn knobs to
desired setting.

www.blackstoneproducts.com
10
Turn controls and gas source or tank OFF
when not in use.
! !
WARNING
! !
CAUTION
If ignition does NOT occur in 5 seconds,
turn the burner controls OFF, wait 5
minutes and repeat the lighting
procedure. If the burner does not ignite
with the valve open, gas will continue to
ow out of the burner and could
accidently ignite with risk of injury.
Burner Flame Check
• Light burners, rotate knobs from to low. You
should see a smaller ame in low position than
seen on. Perform burner ame check on
side burner, also. Always check ame prior
to each use. If only low ame is seen refer to
“Sudden drop or low ame” in
the Troubleshooting.
Turning Grill Off
• Turn all knobs to the OFF position. Turn LP
cylinder OFF by turning hand-wheel clockwise
to a full stop.
Ignitor Check
• Turn gas off at LP cylinder. Press and hold
electronic ignitor button. “Click” should be
heard and spark seen each time between each
collector box or burner and electrode. See
“Troubleshooting” if no click or spark.
Valve Check
• Important: Make sure gas is off at LP cylinder
before checking valves. Knobs lock in OFF
position. To check valves, rst push in knobs
and release, knobs should spring back. If
knobs do not spring back, replace valve
assembly before using griddle. Turn knobs to
low position then turn back to OFF position.
Valves should turn smoothly.
Hose Check
• Before each use, check to see if hoses are cut
or worn. Replace damaged hoses before using
griddle. Use only identical replacement part
valve/hose/regulator as specied in the Parts
List of this Use and Care Guide.
General Griddle Cleaning
• Do not mistake brown or black accumulation
of grease and smoke for paint. Interiors of gas
grills are not painted at the factory (and should
never be painted). Apply a strong solution of
detergent and water or use a griddle cleaner
with scrub brush on insides of griddle lid and
bottom. Rinse and allow to completely air dry.
Do not apply a caustic griddle/oven cleaner to
painted surfaces.
• Plastic parts: Wash with warm soapy water and
wipe dry. Do not use Citrisol, abrasive
cleaners, degreasers or a concentrated griddle
cleaner on plastic parts. Damage to and failure
of parts can result.
• Painted surfaces: Wash with mild detergent or
nonabrasive cleaner and warm soapy water.
Wipe dry with a soft nonabrasive cloth.
• Stainless steel surfaces: To maintain your
griddle’s high quality appearance, wash with
mild detergent and warm soapy water and wipe
dry with a soft cloth after each use.
• Baked-on grease deposits may require the use
of an abrasive plastic cleaning pad. Use only in
direction of brushed nish to avoid damage. Do
not use abrasive pad on areas with graphics.
• Cooking surfaces: If a bristle brush is used
to clean any of the griddle cooking surfaces,
ensure no loose bristles remain on cooking
surfaces prior to grilling.

11
Storing Your Griddle
• Clean cooking grates.
• Store in dry location.
• When an LP cylinder is connected to griddle,
store outdoors in a well-ventilated space and
out of reach of children.
• Cover griddle if stored outdoors. Choose
from a variety of griddle covers offered
by manufacturers.
• Store grill indoors ONLY if LP cylinder is turned
off and disconnected, removed from griddle
and stored outdoors.
• When removing griddle from storage, follow
“Cleaning the Burner Assembly” instructions
before starting griddle.
Cleaning the Burner Assembly
Follow these instructions to clean and/or replace
parts of burner assembly or if you have trouble
igniting griddle.
1. Turn gas OFF at control knobs and LP cylinder.
2. Remove cooking grates and ame tamers.
3. Remove carryover tubes and burners.
4. Detach electrode from burner.
NOTE: Removal/Detachment method will
depend on the burner conguration.
5. Carefully lift each burner up and away from
valve openings. We suggest three ways to
clean the burner tubes. Use the one easiest for
you. (A) Bend a stiff wire (a light weight coat
hanger works well) into a small hook. Run the
hook through each burner tube several times.
(B) Use a narrow bottle brush with a exible
handle (do not use a brass wire brush), run the
brush through each burner tube several times.
(C) Wear eye protection: Use an air hose to
force air into the burner tube and out the burner
ports. Check each port to make sure air comes
out each hole.
6. Wire brush entire outer surface of burner to
remove food residue and dirt.
7. Clean any blocked ports with a stiff wire such
as an open paper clip.
8. Check burner for damage, due to normal wear
and corrosion some holes may become
enlarged. If any large cracks or holes are found
replace burner.
VERY IMPORTANT: Burner tubes must
reengage valve openings.
9. Attach electrode to burner.
10. Carefully replace burners.
11. Attach burners to brackets on rebox.
12. Reposition carryover tubes and attach to
burners. Replace ame tamers and
cooking grates.
Food Safety
Food safety is a very important part of enjoying
the outdoor cooking experience. To keep food safe
from harmful bacteria, follow these four
basic steps:
Clean: Wash hands, utensils, and surfaces with
hot soapy water before and after handling raw
meat and poultry.
Separate: Separate raw meats and poultry
from ready-to eat foods to avoid cross
contamination. Use a clean platter and utensils
when removing cooked foods.
Cook: Cook meat and poultry thoroughly to kill
bacteria. Use a thermometer to ensure proper
internal food temperatures.
Chill: Refrigerate prepared foods and leftovers
promptly. For more information Visit the
Canadian partnership for Consumer Food
Safety Education-www.befood safe.ca.
How To Tell If Meat Is Grilled Thoroughly
• Meat and poultry cooked on a griddle often
browns very fast on the outside. Use a meat
thermometer to be sure food has reached a
safe internal temperature, and cut into food to
check for visual signs of being done.
• Whole poultry should reach 165° F/74°C.
Juices should run clear and esh should not
be pink.
• Hamburgers made of any ground meat or
poultry should reach 160° F/71°C , and be
brown in the middle with no pink juices. Beef,
veal and lamb steaks, roasts and chops can be
cooked to 145° F/63°C . All cuts of pork should
reach 160° F/71°C.
• NEVER partially grill meat or poultry and nish
cooking later. Cook food completely to destroy
harmful bacteria.
• When reheating takeout foods or fully cooked
meats like hot dogs, grill to 165° F/64°C , or
until steaming hot dogs, grill to 165°F/74°C, or
until steaming hot.

www.blackstoneproducts.com
12
ILLUSTRATED PARTS LIST
1. Body (1 pc)
(with knob valve)
3. Side shelf (2 pcs)
5. Griddle Top (1 pc)
7. Upper Hanger (1 pc)
2. Bottom tray (1 pc)
4. Side Handle (1 pc)
6. Oil cup (1 pc)
8. Small knob (4 pcs)

13
ILLUSTRATED HARDWARE LIST
9. Large knob (2 pc)
11. M6x38 Screw (4 pcs)
14. M6x12 Screw (4 pcs)
Tools needed for assembly
• Phillip screwdriver
• Crescent wrench
10. Lower tank fastener (1 pc)
12. M6 Nut (4 pcs)
13. M6 Flange Nut (4 pcs)
15. Valve knob (4 pcs)
16. Ignition Button (1 pc)
Items not included
• LP Gas Tank • AA Battery

www.blackstoneproducts.com
14
WARNING: The manufacturer has made every effort to eliminate any sharp edges. However, you
should handle all components with care to avoid accidental injury. Tools required: The only tool
needed is a Phillips Screwdriver needed for minimal assembly on the cover and main body handles.
ASSEMBLY:
Please read all instructions thoroughly before proceeding. Find a large, clean area in which to
assemble your grill. Please refer to the parts list and assembly diagram as necessary. Grill assembly
involves large components; therefore, it is advised to have two people set up the unit.
NOTICE:Make sure all the plastic protection is removed before assembling
Step 1:
Open the Leg assembly. See Below
Step 1:
.
Pivot both leg assemblies to a vertical position.
Valve knob
Ignition button
Leg assembly
Next, place each Valve Knob on a burner valve.
Insert a AA battery (not included) into the battery socket with the positive
terminal facing out. Screw on the Ignition Button.
Pull out

15
Step 2 :
Install the Bottom Tray. See Below.
Secure the tray in place with the Large Knob. Repeat step for both sides.
Bottom tray
Large Knob

www.blackstoneproducts.com
16
Step 4 :
Connect the Side Handle using the
M6x12 Screw with M6 Flange Nut.
Step 3 :
Insert Side Shelves and secure with Small Knobs.
Small Knob Side Shelf
M6 Flange Nut M6x12 Screw

17
Step 5 :
will line up with docking holes in the top of the appliance body.
Step 6 :
Hang the Oil Cup on the side of the Griddle, just under the drip hole.
Griddle top

www.blackstoneproducts.com
18
Step 7 :
Install the cylinder Upper Hanger and Lower Fastener on the left leg assembly. See Below.
Step 8 :
Hang up the LP Gas Cylinder.
M6x38 Screw
M6 Nut

19
CARE AND MAINTENANCE
Regularly clean your grill between uses and especially after extended periods of storage.
Ensure that the grill and its components are sufciently cool before cleaning.
• Never handle hot parts with unprotected hands.
• In order to extend and maintain the life and condition of your grill, we strongly recommend
that the unit be covered when left outside for any length of time, especially during the
winter months.
Burner maintenance:
In most circumstances, burning off the residue after cooking will keep the burner clean. The burner
should be removed and cleaned annually or whenever heavy build-up is found in order to ensure that
there is no blockage (debris, insects) in either the burner portholes or venture tubes. Use pipe cleaner
to clear obstructions. A wire brush can be used to remove corrosion from the burner surfaces. When
retting the burner, be careful to check that the venture tubes of the burner t over the valve outlets.
Fittings and Storage:
Annual checking and tightening of metal ttings is recommended. Store the grill in a cool dry place.
Cover the burners with aluminum foil in order to prevent insects or other debris from collecting in the
burner holes. If the grill is to be stored indoors, the gas bottle must be disconnected and left outside.
The gas bottle should always be stored outside, out of reach of children, and in a dry, well-ventilated
area away from any sources of heat or ignition.
TROUBLE SHOOTING
PROBLEM POSSIBLE CAUSE SOLUTION
Burner will not light using the
ignition system.
1. Check battery.
2. LP gas cylinder is empty.
3. Faulty regulator.
4. Obstructions in the burner.
5. Obstructions in gas jets or
gas hose.
6. Electrode wire is loose or
disconnected on electrode
or ignition unit.
7. Electrode or wire is
damaged/faulty pushbutton
igniter.
1. Replace with a good battery.
2. Replace with full cylinder.
3. Have the regulator checked
or replaced.
4. Clean burner.
5. Clean jets and gas hose.
6. Reconnect wire.
7. Change electrode and wire
change igniter.
Burner will not light with a
match.
1. LG gas cylinder is empty.
2. Faulty Regulator.
3. Obstructions in burner.
4. Obstructions in gas jets or
gas hose.
1. Replace with full cylinder.
2. Have the regulator checked
or replaced.
3. Clean Burner.
4. Clean jets and gas hose.
Fire in burner tube has a low
ame or ashback (a hissing or
roaring noise may be heard)
1. LP gas cylinder is empty.
2. Obstructions in burner.
3. Obstructions in gas jets or
gas hose.
4. Windy conditions.
1. Use larger cylinder.
2. Clean burner.
3. Clean jets and gas hose.
4. Use grill in a more sheltered
position.

www.blackstoneproducts.com
20
North Atlantic Imports LLC
90-Day Warranty
North Atlantic Imports, the manufacturer of Blackstone 36” Griddle Cooking Station (Model #1566), will war-
ranty for 90 days from purchase all parts, workmanship, and nishes. It will be the manufacturer’s option as to
whether to repair or replace any of the above items. All warranties are limited to the original purchaser only.
This warranty does not cover any liability on the part of North Atlantic Imports, its agents or employees, for any
indirect or consequential damages for breach of warranty. The purchaser must follow the manufacturer’s usage
instructions. Under no circumstances is the manufacturer responsible for damages from the failure to operate
the cooking station properly. It is the responsibility of the purchaser to establish the warranty period by verifying
the original purchase date with original sales receipt.
For more detailed explanation of the warranty, read below:
North Atlantic Imports LLC warrants to the owner that the product covered by this agreement is free from defects in
material and workmanship under normal use and service for which it was intended if, but only if, it has been oper-
ated in accordance with North Atlantic Imports LLC instructions exclusively for domestic use, and not for private
or public club, institutional or commercial purposes. North Atlantic Imports LLC’s obligation under this warranty is
limited to replacing or repairing, free of charge, any part or parts that may prove, to the satisfaction in North Atlantic
Imports LLC, to be defective under normal home use and service within the following stated periods of time from the
date of purchase; a) for ninety (90) days from purchase, all parts, nish, and workmanship. Should any failure to
conform to this warranty become apparent during applicable warranty periods stated above, the original
purchaser must notify NorthAtlantic Imports LLC of breach or warranty within the applicable warranty period. North
Atlantic Imports LLC shall upon notice and compliance by the original purchaser with such instructions, correct such
nonconformity by repair or replacement of the defective part or parts. Correction in the manner provided above
shall constitute a fulllment of all obligations of North Atlantic Imports LLC with respect to the quality if the prod-
uct.
North Atlantic Imports LLC does not warrant this equipment to meet the requirement of any safety code of any state,
municipality or other jurisdiction, and the original purchaser assumes all risk and liability whatsoever resulting
from the use thereof, whether used in accordance with North Atlantic Imports LLC instructions or otherwise. This
warranty does not cover and is intended to exclude any liability on the part of North Atlantic its agents, servants or
employees whether under this warranty or implied by law for any indirect or consequential damages
for breach on any warranty. The purchaser must establish all applicable warranty periods pursuant to this
warranty by verifying the original purchase date by producing the dated sales receipt. This warranty shall not
apply to this product or any other part thereof which has been subject to accident, negligence, alteration, abuse,
or misuse or which as been repaired or altered without North Atlantic written consent, outside of North Atlantic
Imports LLC factory. North Atlantic Imports LLC makes no warranty whatsoever in respect to accessories or
parts not supplied with it. This warranty shall apply only within the boundaries of the Unites States of America.
This warranty gives the original purchaser specic rights, and the original purchaser may also have other rights,
which vary from state to state.