Black stone Omnivore 2311 User manual

BLACKSTONEPRODUCTS.COM/SUPPORT

ENGLISH

SAFETY ALERT KEY

DANGER

Indicates a hazardous situation

that, if not avoided, will result in

death or serious injury.

CAUTION

Indicates a hazardous situation

that, if not avoided, could result

in minor or moderate injury.

WARNING

Indicates a hazardous situation

that, if not avoided, could result

in death or serious injury.

NOTICE

Indicates information considered

important, but not hazard-

related (e.g. messages related to

property damage).

OWNER’S MANUAL

IMPORTANT:

This instruction manual contains important

information necessary for the proper assembly and safe

use of the appliance.

Read and follow all warnings and instructions before

assembling and using the appliance.

Follow all warnings and instructions when using

the appliance.

Keep this manual for future reference.

Installer/Assembler: Leave these instructions with the consumer.

For the latest version of this manual,

scan this code or visit

BlackstoneProducts.com/support

| CONTACT CUSTOMER SUPPORT BEFORE RETURNING APPLIANCE TO RETAILER.

MODEL:  v03

28" GRIDDLE

WITH HOOD

TABLE OF CONTENTS

IMPORTANT SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . .

WARRANTY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

ASSEMBLY GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

USING YOUR BLACKSTONE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 



ENGLISH

BLACKSTONEPRODUCTS.COM/SUPPORT

OWNER’S MANUAL | IMPORTANT SAFETY INFORMATION

GAS APPLIANCE SAFETY

• The use of alcohol, prescription, or non-prescription drugs may

impair the consumer’s ability to properly assemble or safely

operate the appliance.

• Keep children and pets away from the appliance at all times.

• Have a type BC or ABC fire extinguisher readily available.

DO NOT USE FOR PURPOSES OTHER THAN INTENDED.

• DO NOT use for commercial cooking.

• DO NOT use this appliance as a heater.

WARNING

Improper installation, use, adjustment, alteration, service,

modification, or maintenance can cause injury or property

damage. Refer to this manual.

INSTALLATION MUST CONFORM WITH LOCAL CODES.

In the absence of local codes, installation must conform with

either ANSI Z223.1/NFPA 54, CSA B149.1, or CSA B149.2.

FOR OUTDOOR USE ONLY.

WARNING

•DO NOT store or use gasoline or other flammable liquids

or vapors in the vicinity of this or any other appliance.

•An LPG cylinder not connected for use shall not be

stored in the vicinity of this or any other appliance.

DANGER

If you smell gas:

•Shut o gas to the appliance.

•Extinguish any open flame.

•Open hood (if applicable).

•If odor continues, keep away from the appliance

and immediately call your gas supplier or your fire

department.

Failure to follow these instructions could result in fire or

property damage, personal injury or death.

DANGER

•NEVER operate this appliance unattended.

•If a fire should occur, keep away from the appliance and

immediately call your fire department. DO NOT attempt

to extinguish an oil or a grease fire with water.

Failure to follow these instructions could result in fire or

property damage, personal injury or death.

MODEL: 

IMPORTANT SAFETY INFORMATION



BLACKSTONEPRODUCTS.COM/SUPPORT

ENGLISH

| OWNER’S MANUALWARRANTY

Register your appliance at

BlackstoneProducts.com/register

The North Atlantic Imports LLC 1-Year Warranty covers replacement

parts up to one year after the date of purchase.

TO ENABLE THIS WARRANTY, YOU WILL NEED TO PROVIDE:

☞

☞ Your appliance’s Serial Number

The Serial Number can be found on your appliance’s

Manufacturer Label.

(The Manufacturer Label is a large silver sticker found on the body of your

appliance.)

WARRANTY OVERVIEW

North Atlantic Imports, the manufacturer, will warranty for one year

from purchase all parts, workmanship, and finishes. It will be the

manufacturer’s option as to whether to repair or replace any of the

above items. All warranties are limited to the original purchaser

only. This warranty does not cover any liability on the part of North

Atlantic Imports, its agents or employees, for any indirect or conse-

quential damages for breach of warranty. The purchaser must follow

the manufacturer’s usage instructions.

Under no circumstances is the manufacturer responsible for

damages from the failure to operate the cooking station properly. It is

the responsibility of the purchaser to establish the warranty period

by verifying the original purchase date with original sales receipt.

DETAILED ExPLANATION OF THE WARRANTY

North Atlantic Imports LLC warrants to the owner that the product

covered by this agreement is free from defects in material and work-

manship under normal use and service for which it was intended if,

but only if, it has been operated in accordance with North Atlantic

Imports LLC instructions exclusively for domestic use, and not for

private or public club, institutional or commercial purposes.

North Atlantic Imports LLC’s obligation under this warranty is limited

to replacing or repairing, free of charge, any part or parts that

may prove, to the satisfaction of North Atlantic Imports LLC, to be

defective under normal home use and service within the following

stated periods of time from the date of purchase; for one year from

purchase, all parts, finish, and workmanship. Should any failure

to conform to this warranty become apparent during applicable

warranty periods stated above, the original purchaser must notify

North Atlantic Imports LLC of breach of warranty within the appli-

cable warranty period.

North Atlantic Imports LLC shall upon notice and compliance by the

original purchaser with such instructions, correct such nonconfor-

mity by repair or replacement of the defective part or parts.

Correction in the manner provided above shall constitute a fulfill-

ment of all obligations of North Atlantic Imports LLC with respect to

the quality of the product.

North Atlantic Imports LLC does not warrant this equipment to meet

the requirement of any safety code of any state, municipality or other

jurisdiction, and the original purchaser assumes all risk and liability

whatsoever resulting from the use thereof, whether used in accor-

dance with North Atlantic Imports LLC instructions or otherwise.

This warranty does not cover and is intended to exclude any liability

on the part of North Atlantic its agents, servants or employees

whether under this warranty or implied by law for any indirect or

consequential damages for breach on any warranty. The purchaser

must establish all applicable warranty periods pursuant to this

warranty by verifying the original purchase date by producing the

dated sales receipt. This warranty shall not apply to this product or

any other part thereof which has been subject to accident, negli-

gence, alteration, abuse, or misuse or which has been repaired or

altered without North Atlantic written consent, outside of North

Atlantic Imports LLC factory. The full manufacturer warranty is

not valid for griddles purchased from unlicensed, third-party

resellers, purchased at a discount due to missing or damaged

parts, or purchased as a floor model; at the discretion of North

Atlantic Imports.

North Atlantic Imports LLC makes no warranty whatsoever in respect

to accessories or parts not supplied with it. This warranty shall

apply only within the boundaries of the United States of America and

Canada. This warranty gives the original purchaser specific rights,

and the original purchaser may also have other rights, which vary

from state to state.

��

☞

FREE

MOBILEFRIENDLY

COOKBOOK

when you register



MODEL: 

WARRANTY



ENGLISH

BLACKSTONEPRODUCTS.COM/SUPPORT

OWNER’S MANUAL | ASSEMBLY GUIDE MODEL: 

ASSEMBLY GUIDE

ExPLODED VIEW

PARTS LIST

PARTS

QTY

1.1a Control panel 

1.1b

Control knob bezels



1.2

Left leg assembly



PARTS

QTY

1.3 Right leg assembly 

1.4

Ignitor



1.5

Ignition heat shield



PARTS

QTY

1.6 Gas rail 

1.7

H burners



1.8

Ignition needles



PARTS

QTY

1.9 Regulator 

2.1

Hood



2.2

Griddle top



8

1.1a

1.5

1.2

1.7

1.1b

1.6

1.3

1.9

1.8

1.4

1

12

6

5

9

13

7

2.1

10

3

2.2

4

11



BLACKSTONEPRODUCTS.COM/SUPPORT

ENGLISH

| OWNER’S MANUALASSEMBLY GUIDEMODEL: 

1 Body (1 piece) 2 Griddle top and hood (1 piece) 3 Stabilizing shelf (1 piece)

4 Logo panel (1 piece) 5 Hood handle (1 piece) 6 Side shelves

(2 pieces)

7 Side shelf rails

(2 pieces)

8 Control knobs

(2 pieces)

9 Grease cup

(1 piece)

10 Shelf basket

(1 piece)

11 LPG hook

(1 piece)

12 LPG support

(1 piece)

13 Wheels

(2 pieces)

14 Hardware pack (1 piece)

a.M6x12 bolts (8 pieces)

b.M5x24 shoulder bolts (4 pieces)

c.Shear pin (1 piece)

d.Cotter pin (1 piece)

e.Small thumb screws (2 pieces)

f. Wing nuts (6 pieces)

g.Shelf hooks (6 pieces)

h.Large thumb screw (1 piece)

i. Medium thumb screw (1 piece)

j. Slotted washers (6 pieces)

k.Washers (6 pieces)

l. M5 nuts (4 pieces)

[e.][a.]

[k.]

[g.]

[c.]

[d.]

[b.]

[l.]

[j.]

[h.]

[i.]

[f.]



ENGLISH

BLACKSTONEPRODUCTS.COM/SUPPORT

OWNER’S MANUAL | ASSEMBLY GUIDE

ASSEMBLY INSTRUCTIONS

Find a large, clean area to assemble your appliance.

Remove all packing material before assembling.

CAUTION

Sharp edges. Wear gloves while assembling.

NOT INCLUDED (OPTIONAL):

Two (2) D batteries

ELECTRIC REQUIREMENTS:

120V 60Hz

CAUTION

Heavy pieces. Two people should assemble this appliance.

NOTICE

Place appliance on a heat-resistant and flame-resistant

surface while in use.

NOTICE

DO NOT leave the hood closed for more than 10 minutes while

cooking.

NOTICE

•DO NOT mix old and new batteries.

•DO NOT mix alkaline, standard (carbon-zinc) or rechargeable

(ni-cad, ni-mh, etc.) batteries.

NOTICE

DO NOT place items on stabilizing shelf during use.

TOOLS NEEDED:

#3 Phillips head screwdriver &

Adjustable wrench

TOOL NEEDED:

#3 Phillips head screwdriver

TOOL NEEDED:

Adjustable wrench

TOOL NEEDED:

5mm Allen wrench

NOT INCLUDED:

LPG cylinder

Size: 18 x 12 in (45 x 30 cm), 20 lb (9 kg)

LPG cylinder must include collar to

protect LPG cylinder valve.

NOT INCLUDED:

17" griddle base

NOT INCLUDED:

22" griddle base

NOT INCLUDED:

AA battery

NOT INCLUDED:

LPG cylinder

Size: 4 x 8 in (10 x 20 cm), 1 lb (453 g)Size: 4 x 8 in (10 x 20 cm), 1 lb (453 g)

NOT INCLUDED:

One (1) AA battery (for ignition)

Optional four (4) AA batteries

(for the motor)

TOOLS NEEDED:

#3 Phillips head screwdriver &

Adjustable wrench

TOOL NEEDED:

#3 Phillips head screwdriver

TOOL NEEDED:

Adjustable wrench

TOOL NEEDED:

5mm Allen wrench

NOT INCLUDED:

LPG cylinder

Size: 18 x 12 in (45 x 30 cm), 20 lb (9 kg)Size: 18 x 12 in (45 x 30 cm), 20 lb (9 kg)

LPG cylinder must include collar toLPG cylinder must include collar to

protect LPG cylinder valve.protect LPG cylinder valve.

NOT INCLUDED:

17" griddle base

NOT INCLUDED:

22" griddle base

NOT INCLUDED:

AA battery

NOT INCLUDED:

LPG cylinder

Size: 4 x 8 in (10 x 20 cm), 1 lb (453 g)Size: 4 x 8 in (10 x 20 cm), 1 lb (453 g)

NOT INCLUDED:

One (1) AA battery (for ignition)

Optional four (4) AA batteries

(for the motor)

TOOLS NEEDED:

#3 Phillips head screwdriver &

Adjustable wrench

TOOL NEEDED:

#3 Phillips head screwdriver

TOOL NEEDED:

Adjustable wrench

TOOL NEEDED:

5mm Allen wrench

NOT INCLUDED:

LPG cylinder

Size: 18 x 12 in (45 x 30 cm), 20 lb (9 kg)Size: 18 x 12 in (45 x 30 cm), 20 lb (9 kg)

LPG cylinder must include collar toLPG cylinder must include collar to

protect LPG cylinder valve.protect LPG cylinder valve.

NOT INCLUDED:

17" griddle base

NOT INCLUDED:

22" griddle base

NOT INCLUDED:

AA battery

NOT INCLUDED:

LPG cylinder

Size: 4 x 8 in (10 x 20 cm), 1 lb (453 g)Size: 4 x 8 in (10 x 20 cm), 1 lb (453 g)

NOT INCLUDED:

One (1) AA battery (for ignition)

Optional four (4) AA batteries

(for the motor)

MODEL: 

STEP 01 With the help of another person, remove the griddle body

from the packaging and lay it upside down on a smooth, flat surface.

Unlatch and unfold the legs to their vertical position, then use two

(2) small thumb screws [e.]to attach the two (2) wheels onto the

ends of the left leg assembly.

STEP 02 Use one (1) large thumb screw [h.]to attach the stabilizing

shelf to the right leg assembly.

Use one (1) medium thumb screw [i.]to attach the LPG support and

the stabilizing shelf to the left leg assembly.

Note: This shelf is integral to the stability of the appliance

while in use.

[h.]

[i.]



BLACKSTONEPRODUCTS.COM/SUPPORT

ENGLISH

| OWNER’S MANUALASSEMBLY GUIDEMODEL: 

STEP 03 With the help of another person, set the griddle on its feet.

Use one (1) shear pin [c.]and one (1) cotter pin [d.]to attach the LPG

hook to the upper bar of the left leg assembly.

STEP 04 Install the two (2) control knobs by pushing them into place

in the OFF position.

STEP 05 Unscrew the four (4) upper bolts from the sides of the

griddle body.

Use these four bolts and two (2) M6x12 bolts [a.]to attach the logo

panel to the front of the griddle.

STEP 06 Use three (3) wing nuts [f.], three (3) washers [k.], and three

(3) slotted washers [j.]to attach three (3) shelf hooks [g.]to one (1)

side shelf.

Repeat with the other side shelf.

[a.]



ENGLISH

BLACKSTONEPRODUCTS.COM/SUPPORT

OWNER’S MANUAL | ASSEMBLY GUIDE

Make sure the front pins are

seated in the holes, then push

the griddle top back.

❶❶Place the two front pins into

the front locking holes and push

the griddle top back.

❷❷Then, set the two rear pins

into the rear holes.

❶

❶Place the two front pins into

the front locking holes and push

the griddle top back.

❷

❷Then, set the two rear pins

into the rear holes.

Make sure the front pins are

seated in the holes, then push

the griddle top back.

Make sure the front pins are fully

seated in the holes, then push

the griddle top forward to lock

the griddle in place.

Make sure the front pins are fully

seated in the holes, then push

the griddle top forward to lock

the griddle in place.

MODEL: 

STEP 10 With the help of another person, place the griddle top

and hood on the main body by aligning the 4 pins to the holes of

the body.

STEP 09 Hang the grease cup in the slot at the back of the

griddle body.

STEP 08 Loosen the two (2) M6x12 bolts on the right side of the

griddle body.

Hook the right side shelf on these bolts and use two (2) M6x12 bolts

[a.]to secure the side shelf to the right side of the griddle body.

Tighten all four screws.

Repeat with the left side shelf.

STEP 07 Use two (2) M5x24 shoulder bolts [b.]and two (2) M5 nuts

[l.]to attach one (1) shelf rail to one (1) side shelf.

Repeat with the other shelf.

❶

❷

[a.]

top of shelftop of shelf



BLACKSTONEPRODUCTS.COM/SUPPORT

ENGLISH

| OWNER’S MANUALASSEMBLY GUIDE

CAUTION

NEVER leave oil exposed in the rain. This can lead to severe

burns.

Place the included hardcover on the burner when not in use

or if it begins to rain.

NOTICE

•Maximum weight on the side shelf is 10 lbs (4.5 kg).

•The side shelf may get hot while appliance is in use.

CAUTION

Grease build-up on the Flame Tamper can catch fire when

heated.

To prevent damage to the unit and/or injury, clean the top of

the Flame Tamper after each use.

NOTICE

DO NOT sit or stand on the table.

NOTICE

•Maximum weight on the tabletop is 100 lbs (45 kg).

•Maximum weight on the inner shelf is 50 lbs (22.5 kg).

•Maximum weight on the side shelf is 10 lbs (4.5 kg).

CAUTION

Handle will get hot while appliance is in use.

DO NOT touch the handle while appliance is hot.

CAUTION

Heavy pieces. Two people should assemble this appliance.

NOTICE

Place appliance on a heat-resistant and flame-resistant

surface while in use.

NOTICE

DO NOT leave the hood closed for more than 10 minutes while

cooking.

NOTICE

•DO NOT mix old and new batteries.

•DO NOT mix alkaline, standard (carbon-zinc) or rechargeable

(ni-cad, ni-mh, etc.) batteries.

NOTICE

DO NOT place items on stabilizing shelf during use.

CAUTION

Heavy pieces. Two people should assemble this appliance.

NOTICE

Place appliance on a heat-resistant and flame-resistant

surface while in use.

NOTICE

DO NOT leave the hood closed for more than 10 minutes while

cooking.

NOTICE

•DO NOT mix old and new batteries.

•DO NOT mix alkaline, standard (carbon-zinc) or rechargeable

(ni-cad, ni-mh, etc.) batteries.

NOTICE

DO NOT place items on stabilizing shelf during use.

MODEL: 

STEP 11 Use the two (2) M6x12 bolt [a.]to install the hood handle to

the griddle hood.

❶❶Hang the shelf basket on the accessory rail.

❷❷Push the basket in to secure.

STEP 12 Proceed to USING YOUR BLACKSTONE.

❶❶

❷❷



ENGLISH

BLACKSTONEPRODUCTS.COM/SUPPORT

OWNER’S MANUAL | USING YOUR BLACKSTONE

SETTING UP YOUR OUTDOOR SPACE

THIS APPLIANCE MUST ONLY BE USED OUTDOORS.

• DO NOT use this appliance inside buildings, garages, or any other

enclosed area.

• DO NOT install this appliance in or on a boat.

• DO NOT install this appliance in or on a recreational vehicle.

c.Within a partial enclosure that

includes an overhead cover

and three sidewalls, as long as

30% or more of the horizontal

periphery of the enclosure is

permanently open.

b.Within a partial enclosure that

includes an overhead cover

and no more than two side-

walls. The sidewalls may be

parallel, as in a breezeway, or

at right angles to each other.

a.With walls on three sides, but

with no overhead cover.

SHELTERED OUTDOOR AREAS:

All openings must be permanently open; sliding doors, garage doors,

windows or screened openings are not considered as permanent

openings.

An appliance is considered to be outdoors if installed with shelter no

more inclusive than:

MAINTAIN PROPER CLEARANCES FROM COMBUSTIBLE MATERIAL.

• DO NOT use this appliance on or under any apartment or condo-

minium balcony or deck.

• DO NOT obstruct the flow of combustion and ventilation air.

• DO NOT operate this appliance any closer than 36 in (1 m) from the

sides and back of the appliance to combustible construction.

A = 36 in (1 m)

• DO NOT use this appliance under overhead combustible

construction.

BEFORE COOKING

CHECK BURNERS

Prior to connection and use, ensure that there is no debris caught in,

or damage to, the head of the gas cylinder, regulator, hose, burner

and burner ports.

Spiders and insects can nest within and clog the burner/venturi tube

at the orifice.

Please reference the Troubleshooting chapter for burner cleaning

instructions.

 WARNING

A clogged burner can

lead to a fire beneath the

appliance.

Burner should be removed

and cleaned whenever

blockages are found.

DANGER

Flammable items can combust if placed near the appliance.

Keep the appliance area clear and free from combustible

materials, aerosol containers, gasoline and other flammable

vapors and liquids.

THE MINIMUM AMBIENT OPERATING TEMPERATURE IS 0°F (-18°C).

Ensure that the gas

rail fuel nozzle orifice is

correctly engaged within the

burner opening.

A

Both ends open

30%

Venturi

Air intake

Blocked burner

Fuel nozzle

Burner opening

MODEL: 

USING YOUR BLACKSTONE



BLACKSTONEPRODUCTS.COM/SUPPORT

ENGLISH

| OWNER’S MANUALUSING YOUR BLACKSTONE

THE LPG CYLINDER VALVE MUST HAVE:

• Type 1 valve outlet (thread on the outside).

• Safety relief valve.

• UL listed Overfill Protection Device (OPD). This OPD safety feature is

identified by a unique triangular hand wheel.

• Dust cap. LEAK TEST INSTRUCTIONS

• Leak test new and exchanged LPG cylinders BEFORE connecting

to griddle.

• DO NOT smoke during leak test.

• DO NOT use an open flame to check for gas leaks.

• Appliance must be leak tested outdoors in a well-ventilated

area, away from ignition sources such as gas fired or electrical

appliances.

• During leak test, keep appliance away from open flames or sparks.

LEAK TEST: LPG CYLINDER

STEP 01 Use a clean paintbrush

to brush a  mild soap and

water solution onto joint areas of

the LPG cylinder.

(Indicated by arrows in figure 01.)

• Leaks are indicated by

growing bubbles.

WARNING

If growing bubbles appear

during leak test, DO NOT use

or move the LPG cylinder.

Immediately contact an LPG

supplier or fire department.

FILLING & ExCHANGE

• Use only those reputable exchange companies that inspect, preci-

sion fill, test and certify their cylinders. LPG dealer must purge new

cylinder before filling.

• Volume of propane in cylinder will vary by temperature.

WARNING

A frosty regulator indicates gas overfill.

Immediately close LPG cylinder valve and call local LPG

dealer for assistance.

• DO NOT release liquid petroleum gas (LPG) into the atmosphere.

• To remove gas from LPG cylinder, contact a certified LPG dealer or

local fire department for assistance.

• Exchange cylinder only for an OPD safety feature-equipped

cylinder.

Your retailer can help you match a replacement LPG cylinder to your appliance.

LPG CYLINDER REQUIREMENTS

FOR 20 LB (9 KG CYLINDERS)

• The LPG supply cylinder to be used must be constructed and

marked in accordance with the specifications for LP gas cylin-

ders, U.S. Department of Transportation (DOT) or the Standard for

Cylinders, Spheres and Tubes for the Transportation of Dangerous

Goods, CAN/CSA-B339.

• Only LPG cylinders marked “propane” shall be used.

• The LPG cylinder supply system must be arranged for vapor

withdrawal.

•

Always keep new LPG cylinders in upright position during use, transit or

storage.

•

Always keep the ventilation opening(s) of the cylinder enclosure free and

clear from debris.

STORING LPG CYLINDERS

WARNING

•DO NOT store a spare LPG cylinder under or near this

appliance.

•DO NOT fill an LPG cylinder beyond 80% full.

If the information above is not followed exactly, a fire causing

death or serious injury may occur.

• The LPG cylinder must be turned OFF when the appliance is

not in use.

• LPG cylinders must be stored outdoors and out of the reach

of children.

• DO NOT store an LPG cylinder inside a building, garage, or any other

enclosed area.

The seal on the type 1 valve outlet could, over time, show marked and

visible damage or deterioration that might cause a leak even with

the connection tightened.

• A visual inspection for the seal must be carried out every time a

LPG cylinder is replace or refilled.

• Any LPG cylinder showing signs of damage or deterioration as

those illustrated including visible cracks and pitting, must be

returned unused to the seller.

FITTINGS & HOSES

• Annual checking and tightening of metal fittings is recommended.

• Keep the fuel supply hose away from any heated surfaces.

• Before each use, check to see if hoses are cut or worn.

• Replace damaged hose before using appliance.

(Use only Blackstone approved valve, hose, or regulator. Failure to comply will

void the warranty.)

LPG cylinder valveLPG cylinder valve

Safety relief

valve

OPD hand wheel

Type 1 valve outlet

(check seal before use)

GOOD SEALGOOD SEAL

BAD SEALBAD SEAL

Dust cap

figure 01

MODEL: 



ENGLISH

BLACKSTONEPRODUCTS.COM/SUPPORT

OWNER’S MANUAL | USING YOUR BLACKSTONE

CONNECT THE LPG CYLINDER

ONLY USE A 20 LB (9 KG) CYLINDER

STEP 01 Turn the control

knobs to OFF.

❶

❶Ensure that the LPG cylinder

is OFF by turning the OPD hand

wheel clockwise to a full stop.

❷

❷Remove the safety cap from

the Type 1 valve outlet.

STEP 02 Hold the regulator in a

straight line with the Type 1 valve

outlet so as not to cross thread

the connection.

Center and insert the regu-

lator nipple into the Type 1

valve outlet.

Hand-tighten the coupling nut in

a clockwise direction.

(DO NOT use tools to connect.)

If connection cannot be completed,

disconnect regulator and repeat this

step.

LEAK TEST: VALVES, HOSE & REGULATOR

STEP 01 Turn the control knobs to OFF.

STEP 02 Connect the regulator to the LPG cylinder.

STEP 03 Completely open the LPG tank by turning the OPD hand

wheel counterclockwise.

• If you hear a rushing sound, turn gas o immediately. There is a

major leak at the connection.

• Immediately close the LPG cylinder by turning the OPD hand wheel

clockwise and re-tighten connections. If leaks cannot be stopped

DO NOT TRY TO REPAIR.

STEP 04 Use a clean paintbrush

to brush a  mild soap and

water solutionn onto joint areas

of valves and regulator.

(Indicated by arrows in figure 02.)

• Leaks are indicated by

growing bubbles.

• Immediately close the LPG

cylinder by turning the OPD

hand wheel clockwise and

re-tighten connections.

WARNING

If leaks cannot be stopped, DO NOT try to repair.

Regulator must be replaced with a Blackstone approved

model by a professionally licensed, authorized dealer.

The safety relief valve must face

away from the user while the

appliance is in use.

DISCONNECTING THE LPG CYLINDER

STEP 01 Ensure that the control knobs are turned to OFF.

❶

❶Ensure that the LPG cylinder

is OFF by turning the OPD hand

wheel clockwise to a full stop.

❷

❷Turn the coupling nut count-

er-clockwise by hand to remove

the regulator. (DO NOT use tools

to disconnect.)

STEP 02 Place dust cap on LPG

cylinder valve outlet whenever

cylinder is not in use.

Only install the type of dust cap on

cylinder valve outlet that is provided

with the cylinder valve. Other types of

caps or plugs may result in leakage of

propane.

REGULATOR SAFETY

• Use this appliance, as purchased, only with gas and regulator/

valve assembly supplied. DO NOT use quick connect fittings or

other add-ons.

• DO NOT cross thread (force at an improper angle) the connection

between your LPG cylinder and regulator.

• If you can not connect the regulator, DO NOT use the regulator.

Regulator must be replaced with a Blackstone approved model by a profession-

ally licensed, authorized dealer.

❶❶

❷

Coupling nutCoupling nut

Regulator nippleRegulator nipple

figure 02

❶❶

❷

STEP 03 Secure the LPG cylinder

to the appliance by hanging it on

the LPG hook so that it nestles

against the LPG support.

MODEL: 



BLACKSTONEPRODUCTS.COM/SUPPORT

ENGLISH

| OWNER’S MANUALUSING YOUR BLACKSTONE

Turn gas ON by turning the gas

cylinder handwheel counter-

clockwise 1 to 3 turns.

2. BATTERY POWERED IGNITION

DO NOT lean over the appliance while lighting.

STEP 01 Insert one (1) AA

battery (not included) under the

ignitor button.

Screw the button into place over

the positive terminal.

STEP 02

❶

❶ Turn the control knob to OFF.

STEP 03

❷

❷Push and hold the ignitor button.

❸

❸Push and turn the control knob counter-clockwise to HIGH.

(Release the ignitor button when the burner lights.)

❹

❹Adjust the temperature to desired level.

IGNITION INSTRUCTIONS

1. CHECK VALVES

STEP 01 Turn knob to OFF position.

STEP 02 Push in knob and release. Knob should spring back.

If knobs

DO NOT

spring back, replace valve assembly before using appliance.

STEP 03 Rotate knob to LOW then turn back to OFF. Knob should

turn smoothly.

 WARNING

If burner does not ignite with open gas supply valve, gas

will continue to flow out of burner and could accidentally/

inadvertently ignite with risk of injury.

Ensure gas is o at the supply shut o valve before checking

appliance valves.

❷

❸

❶

❹

1 to 3 turns1 to 3 turns

❶

❷

❸

❶❶

❷❷

❸❸

HEALTHY FLAME PATTERN YELLOW OR IRREGULAR

3. ALWAYS CHECK BURNER FLAME BEFORE USE.

STEP 01 Light burners and rotate knobs from HIGH to LOW.

STEP 02 Look below the cooking surface to view burners. When knob

is at HIGH, flames should be larger than when knob is at LOW.

3. ALWAYS CHECK BURNER FLAME BEFORE USE.

STEP 01 Light burner and rotate knob from LOW to HIGH.

STEP 02 Look below the turntable to view burner. When knob is at

HIGH, flames should be larger than when knob is at LOW.

❶

Flickers of yellow color.

❷

Dark blue color.

❸

Vibrant blue.

If there is a sudden drop or low

flame issue, please reference the

Troubleshooting chapter.

IF IGNITION DOES NOT OCCUR IN 5 SECONDS:

STEP 01 Turn the burner control knob OFF.

STEP 02 Wait 5 minutes.

STEP 03 Repeat the lighting procedure.

If burner does not ignite, please reference the Troubleshooting chapter.

IF IGNITION DOES NOT OCCUR IN 5 SECONDS:

STEP 01 Turn the burner control knob OFF.

STEP 02 Wait 5 minutes.

STEP 03 Repeat the lighting procedure.

If burner does not ignite, please reference the Troubleshooting chapter.If burner does not ignite, please reference the Troubleshooting chapter.

HEALTHY FLAME PATTERN YELLOW OR IRREGULAR

❶ ❶ Flickers of yellow color.Flickers of yellow color.

❷ ❷ Dark blue color.Dark blue color.

❸ ❸ Vibrant blue.Vibrant blue.

If there is a sudden drop or lowIf there is a sudden drop or low

flame issue, please reference theflame issue, please reference the

Troubleshooting chapter.Troubleshooting chapter.

MODEL: 



ENGLISH

BLACKSTONEPRODUCTS.COM/SUPPORT

OWNER’S MANUAL | USING YOUR BLACKSTONE

WHAT OIL IS BEST TO USE?

• Blackstone Seasoning and

Cast Iron Conditioner.

• Any plant-based cooking oil.

• Rendered animal fat with no

additives.

WASHING YOUR GRIDDLE TOP BEFORE FIRST USE

SEASONING YOUR GRIDDLE

STEP 01 Wipe any debris o

griddle top.

GRIDDLE SEASONING INSTRUCTIONS

STEP 02 Set your griddle to

high heat until your griddle top

changes color. (~10 min)

STEP 04 The griddle top is ready

for another layer of oil when it

stops smoking. Repeat STEP 03

3-4 times, or until the griddle

surface is black.

SEASONING TROUBLESHOOTING

THERE IS A BROWNISH RESIDUE ON THE GRIDDLE SURFACE:

VIDEO TUTORIAL

How to Season a New Blackstone Griddle

youtube.com/watch?v=VspmDVnj2pI&t=3s

STEP 03 Use tongs to hold a

paper towel or cotton cloth and

spread 2-3 tablespoons of your

seasoning oil across the entire

griddle top.

When seasoning your griddle top,

remember to use a thin and even layer

of oil—the thinner the layer of oil, the

easier it will be to burn it o.

VIDEO TUTORIAL

Recovering your Blackstone Griddle Top

youtube.com/watch?v=thPE2IgnSiI

PREVENTING RUST

Use your griddle frequently. Every time you cook, you are adding to

the seasoning, which makes rust less likely.

NOTICE

If you live in a humid or coastal climate, your griddle may

require more frequent seasonings between uses.

If rust appears on the griddle surface, rub it o with steel wool, low

grit sandpaper or the Blackstone Pumice Stone and re-season

the surface.

THE EDGES OF THE GRIDDLE SURFACE ARE NOT BLACK:

After using your griddle for multiple cooks, the seasoning will even

out and improve.

POSSIBLE CAUSES SOLUTION

•Too much oil was used.

•You turned o the heat too

soon.

STEP 01 Turn your griddle on high

and let it heat for 10-15 minutes.

STEP 02

Scrape o as much

of the thickened and partially

cooked oil as you can.

STEP 03

Re-season with a very

thin layer of oil.

CAUTION

Properly dispose of the rags/towels used to spread oil on

your griddle top to prevent fires that might occur due to

spontaneous combustion.

Under the right conditions, residual oil on rags or towels can oxidize long

after being removed from a heat source. The oxidation process itself produces

heat which, if not dissipated, can build up and may cause the rags/towels and

surrounding material to ignite.

NOTICE

Soap will ruin a seasoned

griddle. This is the only time

you should use soap on the

griddle cooking surface.

STEP 01 Wash the griddle

cooking surface with hot,

soapy water.

STEP 02 Rinse and dry

completely.

MODEL: 



BLACKSTONEPRODUCTS.COM/SUPPORT

ENGLISH

| OWNER’S MANUALUSING YOUR BLACKSTONE

COOKING ON YOUR BLACKSTONE

CAUTION

This appliance will be hot during and after use. Use long-

handled utensils and oven mitts/ protective gloves when

handling potentially hot parts to protect against burns and

splatters.

CAUTION

If the appliance is fitted with a paper towel holder, the arm

must be in the open position while the appliance is in use.

NOTICE

DO NOT store any items within 3 in (8 cm) of the cooking

surface while in use.

IF GREASE OR OTHER HOT MATERIAL DRIPS ONTO VALVE, HOSE OR

REGULATOR:

STEP 01 Turn o gas supply immediately.

STEP 02 Determine the cause and correct it.

STEP 03 Clean and inspect valve, hose and regulator.

STEP 04 Perform a leak test. (Please reference the Leak Test

Instructions)

HOW TO USE YOUR PIzzA OVEN

FRESH PIzzA

STEP 01 Preheat your oven on high for about 20-25 minutes.

STEP 02 Once the desired stone temperature is reached (650°-750°F

(340°- 400°C) for fresh dough pizza), turn the control knob to low.

Depending on what you are cooking, you may adjust the temperature

while cooking to achieve desired results.

Note: The thermometer only measures the air temperature in the

oven, NOT the stone temperature. Use an infrared thermometer (not

included) to measure the bottom stone temperature. Proper stone

temperature is critical for consistent results.

STEP 03 Pizza cooking time is about 2-4 minutes depending on the

size and thickness of the pizza.

• Thinner foods should be cooked at a higher temperature for a

shorter time.

• Thicker or denser foods should be cooked at a lower temperature

for a longer time.

STEP 04 Pull the pizza out when the crust has reached your desired

readiness, or when the edges of the pizza crust are golden-brown.

FOR BEST RESULTS:

• Wait to put a new pizza in until the temperature of the bottom stone

is back to your desired temperature.

• Set the temperature to HIGH between cooks and LOW during cooks.

• Keep the door closed as much as possible to retain heat.

• Experiment with pieces of dough beforehand to determine the

optimal stone temperature for your pizza.

FROzEN PIzzAS, COOKIES, ETC.

Follow the food manufacturer’s directions. Let frozen food thaw a

little before putting it into the hot oven. This will prevent your pizza

stone from cracking.

CLEANING YOUR OVEN INTERIOR

STEP 01 Apply a strong solution of detergent and water, or use an

oven cleaner with scrub brush on insides of oven lid and floor. Rinse

and allow to completely air dry.

STEP 02 Reference the Troubleshooting chapter for instructions on

cleaning the burner.

VIDEO RECIPES

Find recipes and cooking tips at:

 BlackstoneProducts.com/recipes

 youtube.com/BlackstoneGriddles

   @blackstoneproducts

STRAWBERRIES AND CREAM

PANCAKES

Breakfast

TACOS BORRACHOS

Dinner

OKLAHOMA FRIED ONION

BURGER

Lunch

CLEANING YOUR GRIDDLE TOP

Clean griddle top after each use, while still warm.

• DO NOT use soap on the griddle top. This will destroy the griddle’s

seasoning.

STEP 01 Push loose food debris

into the grease cup with spatula

or straight metal scraper.

STEP 02 Wipe down griddle top

with paper towel.

STEP 03 Apply a few tablespoons

of water to the griddle surface,

then scrape the water and debris

into the grease cup.

(For stuck-on food residue, use a

bit of coarse salt.)

STEP 04 Wipe again with a paper

towel and dry completely.

STEP 05 Apply thin coat

of cooking oil to maintain

seasoning and protect the

griddle top.

VIDEO TUTORIAL

How to Clean your Blackstone Griddle

youtube.com/watch?v=-Iedu9z6NPY

HOW TO USE YOUR PIzzA OVEN

FRESH PIzzA

STEP 01 Preheat your oven on high for about 12-15 minutes.

STEP 02 Once the desired stone temperature is reached (650°-750°F

(340°- 400°C) for fresh dough pizza), turn the control knob to low.

Depending on what you are cooking, you may adjust the temperature

while cooking to achieve desired results.

Note: The thermometer only measures the air temperature in the

oven, NOT the stone temperature. Use an infrared thermometer (not

included) to measure the bottom stone temperature. Proper stone

temperature is critical for consistent results.

STEP 03 Pizza cooking time is about 2-4 minutes depending on the

size and thickness of the pizza.

• Thinner foods should be cooked at a higher temperature for a

shorter time.

• Thicker or denser foods should be cooked at a lower temperature

for a longer time.

STEP 04 Pull the pizza out when the crust has reached your desired

readiness, or when the edges of the pizza crust are golden-brown.

FROzEN PIzzAS, COOKIES, ETC.

Follow the food manufacturer’s directions. Let frozen food thaw a

little before putting it into the hot oven. This will prevent your pizza

stone from cracking.

CLEANING YOUR OVEN INTERIOR

If the pizza falls o the rotating stone and catches on fire:

STEP 01 Turn OFF the control knob, turn OFF the LPG cylinder, turn

OFF the rotating motor.

STEP 02 Allow the oven to completely cool.

STEP 03 Remove the oven lid, the top stone, and the lower stone.

STEP 05 Use a spatula to scrape and remove debris from cooking

cavity floor. Wipe cooking cavity with a damp cloth. DO NOT use

detergent.

STEP 06 Use a vacuum if necessary to clean out food debris inside

cooking chamber.

If necessary, reference the Troubleshooting chapter for instructions onIf necessary, reference the Troubleshooting chapter for instructions on

cleaning the burner.cleaning the burner.

STEP 04 Remove the turntable

by removing the two (2) bolts

that attach the turntable to the

rotating shaft.

CLEANING YOUR PIzzA STONE

STEP 01 Set your oven to HIGH for 15~20 min to burn o residue.

STEP 02 Once your oven has cooled completely, flip the stone over

and use the cleaner side.

NOTICE

DO NOT use soap on the cooking stone. This will leave a soap

taste in food.

EMPTY YOUR GREASE CUP

The grease cup must be removed and emptied after each use.

CAUTION

Grease cup will be hot during and after use. DO NOT remove

the grease cup until the griddle has completely cooled.

MODEL: 



ENGLISH

BLACKSTONEPRODUCTS.COM/SUPPORT

OWNER’S MANUAL | USING YOUR BLACKSTONE

APPLIANCE STORAGE

WARNING

DO NOT move the appliance when in use. Allow the appliance

to cool to 115°F (45°C) before moving or storing.

Storage of an appliance indoors is only permissible if the gas supply

is disconnected and removed from the appliance.

COVER FIT GUIDE

Always cover your appliance when stored outdoors.

To find a cover that will fit your appliance, visit

BlackstoneProducts.com/support.

CARE AND MAINTENANCE

WARNING

Grease build up can cause a fire. Clean any part of the

appliance that gets hot and experiences grease build up after

each use.

CAUTION

All cleaning and maintenance should be carried out when the

appliance is cool and everything is turned OFF.

• DO NOT use abrasive pad on areas with graphics.

• If a bristle brush is used to clean any of the cooking surfaces,

ensure no loose bristles remain on cooking surfaces prior

to cooking.

APPLIANCE BODY:

Wash with warm soapy water and immediately wipe dry with a

non-abrasive cloth. (DO NOT allow cleaning agents to rest on any

porous surface for a prolonged amount of time.)

NOTICE

DO NOT use Citrisol, abrasive cleaners, or a concentrated

cleaner on the appliance. This may result in damage to and

failure of parts.

MODEL: 



BLACKSTONEPRODUCTS.COM/SUPPORT

ENGLISH

| OWNER’S MANUALTROUBLESHOOTING

POSSIBLE CAUSES SOLUTION

Something is blocking the

venturi in the burner. Clean the burner assembly to

remove the obstruction.

POSSIBLE CAUSES SOLUTION

Obstructions in the burner, gas

jets, or fuel rail.

Clean the burner, jets, and gas

hose.

Gas cylinder is empty or low.

Refill or replace the gas

cylinder.

The regulator’s flow limiting

device was triggered.

Reset the safety system:

STEP 01

Turn OFF the appliance,

close the LPG cylinder valve, and

disconnect the regulator from

the LPG cylinder.

STEP 02

Wait five minutes to

allow the pressure to dissipate,

then reconnect the regulator

to the LPG cylinder and slowly

open the OPD hand wheel one

half turn.

STEP 03

Ignite your appliance.

Regulator stuck in safety

position. Contact customer support for

replacement parts.

GAS FLOW TROUBLESHOOTING

BURNER FLAMES ARE YELLOW OR IRREGULAR:

A FLAME IS COMING OUT OF THE AIR GATE:

• Appliance will not achieve a high heat or heats unevenly.

• Burner flames start strong, then immediately drop to low even

when burner is set to high position.

• Flame height drops when a second burner is lit.

• Flames DO NOT extend the full length of the burner, or only run on

one side of the burner.

• Burner flames are inconsistent.

IGNITION TROUBLESHOOTING

BURNER WILL NOT IGNITE:

If ignition does not occur in 5 seconds:

STEP 01 Turn the burner control knob OFF.

STEP 02 Wait 5 minutes.

STEP 03 Repeat the lighting procedure.

If this does not work, to determine the cause, please try to ignite your appli-

ance with a match.

MATCH LIGHTING INSTRUCTIONS

Before beginning, check for gas leaks. Open hood (if applicable).

STEP 01 Turn control knob to OFF position.

STEP 04 Push in and turn the control knob to start gas flowing.

Ensure burner lights and stays lit.

STEP 02 Light a match (or long

lighter) no shorter than 11

inches long.

STEP 03 Place the flame next to

the burner.

IF YOU CAN IGNITE YOUR APPLIANCE WITH A MATCH:

POSSIBLE CAUSES SOLUTION

Ignitor wire misaligned.

Ensure that the ignitor needle

is positioned 3-7mm (1/8-1/4

inch) away from the burner, and

aligned with the burner holes.

Damage to the ignition system.

Contact customer support for

replacement parts.

IF YOU CAN NOT IGNITE YOUR APPLIANCE WITH A MATCH:

POSSIBLE CAUSES SOLUTION

Burner tubes are not receiving

fuel.

Clean the burner assembly to

remove the obstruction.

3-7mm

(- inch)

Dead / improperly installed

battery.

Replace with new battery.

MODEL: 

TROUBLESHOOTING



ENGLISH

BLACKSTONEPRODUCTS.COM/SUPPORT

OWNER’S MANUAL | TROUBLESHOOTING

STEP 06 Carefully replace

burners and reattach, with

attention to the location of the

ignition needle.

STEP 01 Ensure that the gas is turned OFF at control knobs and gas

supply. Remove the griddle top.

CLEANING THE BURNER ASSEMBLY

To reduce chance of “flash-back” the procedure below should be

followed at least once a month when spiders are most active or

when your appliance has not been used for a period of time.

STEP 02 Carefully detach and

remove the burner.

STEP 03 Clean the inside of

the burner:

a.Run a bottle brush (not a wire

brush) or a sti wire bent into

a small hook through each

burner tube several times.

b.Use compressed air to blow

through the burner tube and

out the burner ports (Wear eye

protection).

STEP 04 Brush entire

outer surface of burner to

remove grime.

STEP 05 Clean any blocked ports

with sti wire such as an open

paper clip.

VIDEO TUTORIAL

How to Clean Your Burner Tube

youtube.com/watch?v=xKQTCrFCzf8

The gas rail fuel nozzle

must be reengaged within the

burner opening.

Fuel nozzle

Burner opening

CUSTOMER SUPPORT

Visit us online at BlackstoneProducts.com/support

for assistance concerning appliance use, replacement parts, or

your warranty.

CUSTOMER SUPPORT HOURS:

 Monday – Friday

7:00 am – 5:00 pm (Mountain Time)

MODEL: 



BLACKSTONEPRODUCTS.COM/SUPPORT

ENGLISH

| OWNER’S MANUAL

This page intentionally left blank

MODEL: 



ENGLISH

BLACKSTONEPRODUCTS.COM/SUPPORT

This product may be covered by one or more issued U.S. and/or

international patents and may include patent applications pending.

For more information, please visit: BlackstoneProducts.com/patents

DISTRIBUTED BY NORTH ATLANTIC IMPORTS, LLC  W  N LOGAN, UT  USA | BLACKSTONE IS A REGISTERED TRADEMARK OF NORTH ATLANTIC IMPORTS, LLC



Black Stone OMNIVORE 2311 User manual

Popular Grill manuals by other brands