Blain Hydraulics EV40 User manual

www.blain.de Pfaffenstr. 1, 74078 Heilbronn [phone]
1) Wiring check
How? Check if wirings for sensors, drive
and the lift controller are done according to the descriptions in
the EV40 manual.
2) Drive initialization
•Make sure that A1-01 (Access level selection) is set to
2,
•Verify H5-01 (Modbus communication address) is set to “1F”,
•Change H5-02 (Communication speed) to “8” (115.2kbps),
•Power the drive off and on again to activate the setting (wait 3 minutes before re-powering). This will allow
the Pro-Hydro card to communicate with the drive,
•Verify that 10 seconds after re-powering the drive the diagnostic LED on the Pro-Hydro card starts blinking
GREEN at 1 second intervals –See Section 3 and 5 in EV40 Manual when LED blinks RED.
After completing “Initialization”phase further drive access is not necessary!
3) Switching on Wi-Fi communication
How? Place the Wi-Fi jumper correctly on the Pro-Hydro card (The jumper pins are located on the top-
left corner of the Pro-Hydro card, see Section 3.5.1 in the EV40 Manual). Wi-Fi is ENABLED when the two
pins are not connected. Wi-Fi is DISABLED when the jumper is connecting the two pins.
4) Connecting your device to Pro-Hydro card
How? To connect your device (eg. mobile phone) to the Pro-Hydro card use following name of Wi-Fi
network (SSID) and password:-
Wi-Fi network (SSID)
Pro-Hydro
Password
Pro-Hydro
Alternatively, you can scan the QR code on the left.
Type http://172.27.1.1 in the address bar of your browser or
scan the QR code on the right.
5) Checking status menu & Sensor readings
How?When Wi-Fi connection is done successfully, STATUS menu appears on
the smart phone. Check whether pressure and temperature readings are there and
correct. If sensor readings are not correct see Section 3 and 5 in EV40 Manual.
6) Opening the Main Menu
How? Touch on the top left indicator and turn the switch on from the open menu. Enter the
PIN Code 1111 and press OK. The Main Menu opens. Select SYSTEM option and change Unit and Language
preferences when necessary.
EV40 Quick Start Guide
Charge your mobile before proceeding!

www.blain.de Pfaffenstr. 1, 74078 Heilbronn [phone]
7) Inputting Motor, Elevator Installation and Speed & Curves parameters
How? Open the Main Menu by touching on . Select Motor Parameters, Elevator Installations and
Speed & Curves menus to input requested parameters respectively.
8) Perform Learning (oil temperature >22°C)
How?Open the Main Menu and select OPERATION MODE
Before performing learning make sure that oil temperature is above 22°C (72°F). Let the elevator make a few
normal travels at nominal speed. If motor is running but the lift is not moving change the direction of rotation
of the motor by changing the parameter b1-14 (eg. If b1-14 is 1 then set it to 0 or vice versa).
During learning, software will start and stop the lift several times. After a few short travels, lift will stop and
software will show “Learning completed” (a check sign in the box). It will switch to Normal operation
automatically.
When the run is interrupted, mode will return to “Normal operation”and the app shows “learning drive NOT
completed successfully”.
9) If necessary, perform fine tuning
How? After making some travels, open TRAVELS menu and click on a travel. Check the total travel and
levelling times. If necessary, change the deceleration and acceleration durations from SPEED & CURVES menu.
Note: The terminals HC, H1, H2 (on the inverter) must be linked otherwise, the motor will not start unless Safe
Disable function is used.
DELAY DEENERGIZING MOTOR CONTACTORS ABOUT 1 SECOND AFTER THE CAR REACHES THE STOP
SWITCH.