BlastKing KXL Series User manual

blastking.com
Owner’s Manual
KXL10 / KXL10A / KXL15S / KXL15AS / KXL18AS
KXL218AS / KXL318AS
LINE ARRAY SYSTEM

2
All other BlastKing® products purchased in the USA are protected under the regular
manufacturer’s one year warranty. This warranty is intended to protect customers from any
and all manufacturer defects from one year of purchase. The product will be replaced or
repaired at the manufacturer’s discretion upon receipt of the warranted unit along with a
dated proof of purchase from an authorized dealer or distributor. This warranty becomes
null and void under situations including but not limited to misusage, normal wear and tear,
shipping damage and abuse. For international purchases, please contact your local dealer
or sales associate for further warranty information.
FCC Statement
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential instal-
lation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced technician for help.
For manufacture warranty please register this product online at
http://blastking.com/product-registration/
Please write the serial number for future reference
Purchased at:
Date of purchase:

3
blastking.com
IMPORTANT SAFETY PRECAUTIONS AND EXPLANATION OF SYMBOLS
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE AMPLIFIER
COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. WARNING: To prevent fire or electric shock, do not expose this equipment to rain or moisture. Do not use this
apparatus near water.
6. Clean only with a dry cloth.
7. Allow a minimum of 6" (152 mm) clearance behind cabinet for convection cooling. Keep anything that might
restrict airflow from the rear of the enclosure (i.e. draperies, fabric, etc.). Do not block any ventilation opening. This
product contains an internal power amplifier that produces heat.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampli-
fiers) that produce heat.
9. Do not defeat the safety purpose of the grounding-type plug on the three-pronged “Edison” style power cable. The
grounding plug has two blades and a grounding prong. The third prong is provided for your safety. If the provided plug
does not fit your outlet, consult an electrician for the replacement of the obsolete outlet. Do not cut off the grounding
plug or use an adapter that breaks the grounding circuit. This apparatus must be properly grounded for your safety.
10. Protect the power cord from being walked on or pinched, particularly plugs, convenience receptacles, and the
point where they exit from the apparatus.
11. The appliance coupler is the AC mains disconnect and should remain readily operable after installation.
12. Use only attachments/accessories specified by Blastking, USA.
13. Use only with hardware, brackets, and components sold with the apparatus or by Blastking, USA.
14. Unplug the apparatus during lightning storms or when unused for long periods of time.
15. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged
in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not operate normally or has been dropped.
16. Before placing, installing, rigging or suspending any loudspeaker product, inspect all hardware, suspension,
cabinets, transducers, brackets and associated equipment for damage. Any missing, corroded, deformed, or non-load
rated component could significantly reduce the strength of the installation and should be immediately corrected. Use
only hardware which is rated for the loading conditions of the installation and any possible short-term unexpected
overloading. Never exceed the rating of the hardware or equipment.
17. Consult a licensed, professional engineer when any doubt or questions arise regarding a physical equipment
installation.
18. The appliance shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall
be placed on the apparatus.
The lightning flash with the arrowhead symbol within an equilateral triangle is intended to alert the
user to the presence of uninsulated “dangerous” voltage within the product’s enclosure that may be
of sufficient magnitude to constitute a risk of shock to humans.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of
important operation and maintenance (servicing) instructions in this manual.
WARNING!

4
Introduction
The BlastKing KXL line array and ground stacked subwoofers allow the user a wide range of applications.
From permanent installations to rentals, KXL has it all.
The KXL is designed for up to six of the KXL10A and one of the KXL15AS or KXL18AS, per side. The series is available
in both active and passive configurations. For the venue that needs that extra BASS, recommended is the KXL218AS and
KXL318AS ground stacked dual and triple 18” subwoofers!
Installation
Before placing, installing, rigging, or suspending any speaker product, inspect all hardware, suspension, cabinets,
transducers, brackets and associated equipment for damage.
Any missing, corroded, deformed, or non-load rated component could significantly reduce the strength of the installation or
placement. Any such condition severely reduces the safety of the installation and should be immediately corrected. Use only
hardware which is rated for the loading conditions of the installation and any possible short-term,unexpected overloading.
Never exceed the rating of the hardware or equipment. Consult a licensed, professional engineer regarding physical
equipment installation. Ensure that all local, state and national regulations regarding the safety and operation of loudspeakers
and related equipment are understood and adhered to.
Maintenance
These speakers are high quality units made especially according to the BLASTKING USA’s specification.
Overpowering the unit or overheating it because of improper system arrangement could harm the unit.
For longest possible operating life, and to avoid warranty issues, it is recommended that there is at least a few inches of
space around an active speaker.
Please avoid exposing the speaker to moisture or extreme cold conditions. Do not put the speaker anywhere near water
sources as it can damage the unit or cause a short circuit.
Manufacturer takes no responsibility for improper repair, replacement, or any other services conducted by unqualified
technicians.

5
blastking.com
FU SE T 4A/230V
120V AC60Hz
120V AC60Hz 120V AC60Hz
120V AC60Hz
120V AC60Hz
KXL10A
KXL15AS KXL18AS
KXL218AS KXL318AS
KXL10A
2 3 4 5
6
7
89
10 11 12 13 14
Rear panel features
1. High frequency setup
HFC2: Use for two topside sat speakers
HFC1: Use for two middle sat spakers.
Flat line source: Use for two underside sat spakers.
Flat point source: Use for point sound source, as to use one speaker individually.
2. Low cut: This unit have a high-slope LOW CUT filter for eliminating unwanted, press the button when match a sub
speaker.
3. Sensitivity: Adjust the sensitivity 0 dB to 10 dB.
4. Line Input: A XLR line input. It is not compatible with microphone level input and it is not suitable for direct connection
with a microphone. Use this to pass the signal if only one channel signal.
5. Line Out: Used for signal connection among other amplified speakers, the signal comes from input.
6. Power indicator: Illuminates when the unit is connection to the main supplys and switched on.
7. Signal indicator: Illuminates to indicate signal present at the input.
8. Protect Indicator: This illuminates if a fault condition occurs, such as overheating. The amplifier will shut down to
prevent further damage. Normal operation will resume once the fault condition has been rectified.
9. Limiter indicator: Illuminated just before the amplifier begins to clip and distort. Adjust the level control and signal level
from your source so this illuminates only briefly on peaks in the music. Using the system with this on all or much of the
time will result in poor sound quality and damage the speakers and electronics.
10. USB data: Use USB port to connect other devices to adjust parameters.
11. Power supply inlet
12. AC out: Connect the power cord output plug to this connector and the other plug to next device.
13. FuseT6.3AL, 230V
14. Power switch: Turns the system On and Off. Ensure the system volume control at minimum when switching on.
1

6
Technical Information
Model KXL10A KXL10
Type: 10” Active Line Array
Module
10” Passive Line Array
Module
Frequency response (+-3 dB): 65Hz-20KHz
Frequency range (-10dB): 50Hz-18KHz
Maximum SPL: 122dB / 138dB (Peak)
Power rating RMS: 350 Watts
Power rating MAX: 700 Watts
Vertical Adjustment: 0° to 10°
Coverage Pattern (HxV): 100° x 15°
LF Driver: 10” Woofer, 3” VC, Neodymium
HF Driver: 1.4” exit, 3” VC, Titanium
Power amplifier type: Class-D with DSP -
Input connectors: XLR 20K ohms
balanced
Speakon
Output connectors: XLR balanced Speakon
Power consumption: 500 Watts -
Power supply: 120V AC -
Enclosure: 15 & 18 mm Multilayer plywood
Coating: Water resistant black paint
Physical Specifications
Product
Height: 11.18”/284 mm 11.18”/284 mm
Width: 22.83”/580 mm 22.83”/580 mm
Depth: 17.88”/454 mm 17.88”/454 mm
Weight: 56.10 Lbs / 25.50 Kg 51.70 Lbs / 23.50 Kg
Package
Height 12.00”/305 mm 12.00”/305 mm
Width: 25.79”/655 mm 25.79”/655 mm
Depth: 20.67”/525 mm 20.67”/525 mm
Weight: 60.50 Lbs / 27.50 Kg 56.20 Lbs / 25.50 Kg

7
blastking.com
FU SE T 4A/230V
120V AC60Hz
120V AC60Hz
120V AC60Hz
120V AC60Hz
120V AC60Hz
KXL10A
KXL15AS
KXL18AS
KXL218AS KXL318AS
KXL15AS / KXL18AS
Rear panel features
11
12
13 14
2
34
56
7
8
9
1
10
1. Sensitivity: Adjust the sensitivity 0 dB to 10 dB.
2. X-over control: Adjust the full range frequency
limit of the sub from 70Hz (fully anti-clockwise) to
120Hz (fully clockwise).
3. Power indicator: Illuminates when the unit is
connection to the main supplys and switched on.
4. Signal indicator: Illuminates to indicate signal
present at the input.
5. Protect Indicator: This illuminates if a fault
condition occurs, such as overheating. The amplifier
will shut down to prevent further damage. Normal
operation will resume once the fault condition has
been rectified.
6. Limiter indicator: Illuminated just before the
amplifier begins to clip and distort. Adjust the level
control and signal level from your source so this
illuminates only briefly on peaks in the music. Using
the system with this on all or much of the time will
result in poor sound quality and damage the speak-
ers and electronics.
7. Phase switch: The subwoofer has phase switch 0 and 180. Pressing this switch reverses the phase of subwoofer
output with respect to signal input.
8. Line input: A XLR line input. It is not compatible with microphone level input and it is not suitable for direct connection
with a microphone. Use this to pass the signal if only one channel signal.
9. Line out: Used for signal connection among other amplified speakers, the signal comes from input.
10. LINK/X-OVER output switch: LINK (disengaged) is for LINE IN , X-OVER(depressed) is for X-OVER signal.
11. USB data: Use USB port to connect other devices to adjust parameters.
12. Power switch: Turns the system On and Off. Ensure the system volume control at minimum when switching on.
13. Power supply inlet
14. AC out: Connect the power cord output plug to this connector and the other plug to next device.

8
Technical Information
Model KXL15AS KXL18AS
Type: 15” Active Line Array
Subwoofer
15” Active Line Array
Subwoofer
Frequency response (+-3 dB): 50Hz-100Hz
Frequency range (-10dB): 45Hz-100Hz
Maximum SPL: 129dB / 136dB (Peak)
Power rating RMS: 1000 Watts
Power rating MAX: 1800 Watts
LF Driver: 15” Woofer, 4” VC 18” Woofer, 4” VC
Power amplifier type: Class-D with DSP
Input connectors: XLR 20K ohms balanced
Output connectors: XLR balanced
Cooling System: Passive radiator
Power consumption: 1200 Watts
Power supply: 120V AC
Enclosure: 18 mm Multilayer plywood
Coating: Water resistant black paint
Physical Specifications
Product
Height: 17.16”/436 mm 20.1”/510 mm
Width: 22.83”/580 mm 22.83”/580 mm
Depth: 17.88”/454 mm 22.83”/580 mm
Weight: 74.8 Lbs / 34 Kg 90.2 Lbs / 41 Kg
Package
Height 19.29”/490 mm 22.05”/560 mm
Width: 25.19”/640 mm 25.2”/640 mm
Depth: 20.08”/510 mm 25”/635 mm
Weight: 80.3 Lbs / 36.5 Kg 95.7 Lbs / 43.5 Kg

9
blastking.com
Technical Information
Model KXL15S
Type: 15” Passive Line Array Subwoofer
Frequency response (+-3 dB): 50Hz-1KHz
Frequency range (-10dB): 45Hz-1KHz
Maximum SPL: 129dB / 136dB (Peak)
Power rating RMS: 1000 Watts
Power rating MAX: 1800 Watts
LF Driver: 15” Woofer, 4” VC
Sensitivity: 98dB (1w/1m)
Nominal Impedance: 8 Ohm
Connectors: (2) Speakon
Enclosure: 18 mm Multilayer plywood
Coating: Water resistant black paint
Physical Specifications
Product
Height: 17.16”/436 mm
Width: 22.83”/580 mm
Depth: 17.88”/454 mm
Weight: 70.5 Lbs / 32 Kg
Package
Height 19.29”/490 mm
Width: 25.19”/640 mm
Depth: 20.08”/510 mm
Weight: 76 Lbs / 34.5 Kg

10
FU SE T 4A/230V
120V AC60Hz
120V AC60Hz 120V AC60Hz
120V AC60Hz
120V AC60Hz
KXL10A
KXL15AS KXL18AS
KXL218AS
KXL318AS
KXL218AS / KXL318AS
Rear panel features
11
12
13 14
2
3
45
67
8
9
1
10
1. Sensitivity: Adjust the sensitivity 0 dB to 10 dB.
2. X-over control: Adjust the full range frequency limit of the sub from 70Hz (fully anti-clockwise) to 120Hz (fully
clockwise).
3. Delay control: control the depth of delay 0-9ms and 0-0.9ms.
4. Power indicator: Illuminates when the unit is turned on.
5. Signal indicator: Illuminates to indicate signal present at the input.
6. Protect indicator: This illuminates if a fault condition occurs, such as overheating. The amplifier will shut down to
prevent further damage. Normal operation will resume once the fault condition has been rectified.
7. Limiter indicator: Illuminated just before the amplifier begins to clip and distort. Adjust the level control and signal
level from your source so this illuminates only briefly on peaks in the music. Using the system with this on all or much of
the time will result in poor sound quality and damage the speakers and electronics.
8. Phase switch: The subwoofer has phase switch 0 and 180. Pressing this switch reverses the phase of subwoofer
output with respect to signal input.
9. Line input: A XLR line input. It is not compatible with microphone level input and it is not suitable for direct connection
with a microphone. Use this to pass the signal if only one channel signal.
10. Line out: Used for signal connection among other amplified speakers, the signal comes from input.
11. LINK/X-OVER output switch: LINK (disengaged) is for LINE IN , X-OVER(depressed) is for X-OVER signal.
12. USB data: Use USB port to connect other devices to adjust parameters.
13. Power switch: Turns the system On and Off. Ensure the system volume control at minimum when switching on.
14. Power supply inlet

11
blastking.com
Technical Information
Model KXL218AS KXL318AS
Type: 2x18” Powered
Hi-Performance
Subwoofer
3x18” Powered
Hi-Performance
Subwoofer
Frequency response (+-3 dB): 40Hz-100Hz
Frequency range (-10dB): 35Hz-100Hz
Maximum SPL: 131dB / 138dB (Peak) 132dB / 139dB (Peak)
Power rating RMS: 2000 Watts 3000 Watts
Power rating MAX: 3800 Watts 5700 Watts
LF Driver: 2x18” Woofer, 4” VC 3x18” Woofer, 4” VC
Power amplifier type: Class-D with DSP
Audio Processing: DSP-48KHz-56bits
Low-pass filter: 70Hz-120Hz select switch
Phase Switch: 0 - 180º
Connectors: XLR
Power consumption: 2400 Watts
Power supply: 120V AC
Physical Specifications
Product
Height: 22.05”/560 mm 21.65”/550 mm
Width: 42.52”/1080 mm 55.12”/1400 mm
Depth: 26.97”/685 mm 32.28”/820 mm
Weight: 154 Lbs / 70 kg 232.1Lbs / 105.5 Kg
Package
Height 24.21”/615 mm 23.62”/600 mm
Width: 44.29”/1125 mm 56.89”/1445 mm
Depth: 28.54”/725 mm 33.86”/860 mm
Weight: 160.6 Lbs / 73 Kg 239.8 Lbs / 109 Kg

blastking.com
2980 NW 74th Ave.
Miami, FL 33122
Phone: [phone]