Blaupunkt Boston CC 22 User manual

Boston CC 22 3D92147 027 mitQuickOut
76 42 750 013
Operation Instructions
Boston CC 22

3
Boston CC 22 3 D92 147 027 mit QuickOut
76 42 750 013
QuickOut
a
b
QuickOut
11
10
64
14
8
15
1
17
18 121316
9
73 5 2

13
Boston CC22
DEUTSCH
ENGLISH
ITALIANO
PORTUGUES NEDERLAND
ESPAGÑOL SVENSKA FRANÇAIS
Short description
1ON/OFF
Switch the set on/off by turning the
knob.
If “Cod” appears on the display, read
the chapter “Anit-Theft Coding” first.
Volume control:
By turning the knob
SCAN (search operation):
During radio reception, the stations are
briefly sampled by pressing the knob for
approx. one second.
2/rocker switch
Radio: Automatical station tuning
Coding: Read first the “Anti-Theft
Coding” chapter.
:Press rocker switch
to confirm your code
entry.
3<< / >> rocker switch
For fine tuning of the stations
4PS (Preset Station Scan)
Pressing this button briefly samples all
memorized stations of the selected
waveband (FM, MW, LW).
5lo
Use this button to alter the sensitivity of
the automatic station seek operation.
lo lights up <- normal sensitivity
no indication - high sensitivity
Additional function:
Switching from stereo to mono:
Press lo longer than 2 seconds.
6Cassette operation button
FF - Fast Forward operation
Start/stop: Press FF button briefly.
Ejection of the tape
Press button firmly.
7Cassette compartment
8Frequency indication
9Indication of FM storage level
:Indication of preset button
;Stereo indication
<lo indication (seek tuning sensitivi-
ty)
=Indication of selected waveband
(FM, MW, LW)
>M•L (Medium wave - Long wave)
This button is used for selecting either
the medium wave (MW) or long wave
(LW) frequencies.
Press button again for shifting between
MW or LW.
?FM•T (Frequency Modulation)
This button is used for shifting between
the different FM storage levels I, II, III
and “T” (Travelstore - i.e. storing and
calling the five strongest stations of an
area).
Storing “T” - Press FM •T until the
seek tuning indication starts to be dis-
played.
Recalling “T” - Press FM•T ?until T
9is indicated on the display. Then
briefly press the respective preset but-
ton.

Boston CC22
14
@Preset buttons 1, 2, 3, 4, 5
Store station -Keep button depressed
during radio operation until the station
becomes audible again.
Recall station -Briefly press the re-
spective button.
Coding -Read the “Anti-Theft Coding”
chapter first.
Buttons 1-4: Use to enter a code num-
ber.
Press each of the buttons until the
code to be found in the car radio pass-
port is represented on the display.
A“Balance” knob
To adjust the volume of the left and
right channel.
B“Tone” knob
Sound control knob

15
Boston CC22
DEUTSCH
ENGLISH
ITALIANO
PORTUGUES NEDERLAND
ESPAGÑOL SVENSKA FRANÇAIS
Radio Section ............................... 18
Selecting the Desired Waveband.......... 18
Tuning in a Station Automatically.......... 18
Manual Tuning ...................................... 18
Adjusting the Station Seek Sensitivity... 18
Switching from Stereo to Mono............. 19
Memorizing a Station ............................ 19
Automatically Storing the Strongest
Stations ................................................. 19
Activating a Stored Station.................... 19
Briefly Sampling a Station ..................... 20
Sampling Memorized Stations .............. 20
Tape Section................................. 20
Inserting the Tape ................................. 20
Fast Forwarding the Tape ..................... 20
Removing the Tape............................... 20
Care Notes............................................ 21
Appendix....................................... 21
Technical Data ...................................... 21
Contents
Short description ......................... 13
Important information.................. 16
What you need to know! ....................... 16
Traffic safety ......................................... 16
QuickOut ............................................... 16
Installation/connection .......................... 16
Anti-theft coding .......................... 16
Wrong code number entered ................ 16
Switching the code system on .............. 17
Restart following interruption of power
supply.................................................... 17
Switching the code system off .............. 17
Amplifier Section.......................... 17
ON/OFF ................................................ 17
Balance Control .................................... 17
Sound Control ....................................... 17

Boston CC22
16
Important information
What you need to know!
Beforestartingto useyournew carradioyou
shouldcarefullyreadthroughtheinformation
on “Traffic safety” and “Anti-theft coding”.
Traffic safety
Traffic safety has always priority. Use your
car radio in such a manner that you are
always able to cope with and react to the
prevailing traffic situation at any given time.
Remember, even at 50 km/h you are still
moving at a speed of 14 m per seconds.
It is also very important that you are able to
hear, and react to, acoustic warning signals
around you, for example from the police or
the firebrigade.
Therefore, adjust the volume reasonably.
QuickOut
Using the QuickOut handle you can easily
pullyourradiooutoftheinstallationcompart-
ment to take it along. The preset stations
remain stored for a longer time.
To take out the radio.
•press knob (a), take the handle (b) and
pull the unit out.
To listen to the radio or cassette again,
•insert the set into the compartment until
it stops and move the handle back to
the front panel.
If the coding system is off, your set will be
ready for operation.
If the coding system is on, proceed as des-
cribed under “Restart following interruption
of power supply”.
Installation/connection
The code system can only be switched on
and off, if the radio is connected to perma-
nent power.
If you like to install your new car radio by
yourself or add other audio components to
the existing ones, then please read carefully
the enclosed instructions on installation and
connection.
Do not connect the loudspeaker outputs to
ground!
Only use the accessory and replacement
parts approved by Blaupunkt.
Anti-theft coding
The car radio comes standard with the code
system deactivated.
If the anti-theft coding system is on while the
power supply to the unit is interrupted (e.g.
theft,disconnectingthecarbattery),thesetis
electronically blocked. Then it may only be
used again after the appropriate code num-
ber has been entered (see car radio pass-
port).
Wrong code number entered
Itshouldnotbe possible forthievestoascer-
tain the code number by trial-and-error. This
is why the set will be blocked for a certain
period of time, if an incorrect code number is
entered. In this case, “- - -” will appear in the
display.
This waiting time is 10 seconds after the first
three attempts, and 1 hour following subse-
quent attempts.
After 19 unsuccessful attempts, “OFF” will
appear in the display and the set can no
longer be restarted.
Note:
Keep you car radio passport with the code
number in a safe place in order to avoid
“unauthorized access” to your car radio.

17
Boston CC22
DEUTSCH
ENGLISH
ITALIANO
PORTUGUES NEDERLAND
ESPAGÑOL SVENSKA FRANÇAIS
If the power supply to the radio is interrupted
while the code system is switched on, you
need to know the right code number.
The radio will operate again as soon as you
have entered the right code number.
If you lose your radio passport and have
forgotten your code number, you will not be
able to restart the set after the power supply
hasbeeninterrupted.Inthiscase,yourradio
can only be reset in our central customer
service workshop or in one of our service
agencies abroad.
Switching the code system on
Precondition:
The radio must be connected to permanent
power.
In order to switch the code system on:
•Turn the radio off.
• Hold down the preset buttons 1and 4
simultaneously.
•Turn the radio on.
“Cod” briefly appears before the radio
begins to operate.
•Release preset buttons 1and 4.
The code system is on.
“Cod” will be briefly displayed each time the
radio is turned on.
Restart following interruption of
power supply
(Code system switched on)
•Switch on the set.
“Cod” will appear in the display.
•Briefly press preset button 1, “000” will
appear in the display.
•Enter the code number given in the
Blaupunkt car radio passport:
Preset button 1 only allows to choose
“0” or “1”. The first “0” will not be dis-
played.
Example: the code number is 0521.
-Press preset button 1until “000” ap-
pears in the display.
-Press preset button 2five times,
“500” appears in the display.
-Press preset button 3twice, “520”
appears in the display.
-Press preset button 4once, “521”
appears in the display.
•To confirm the code number:
Press the upper part of the rocker
switch .
Your car radio is now ready for operation.
If three dashes appear again in the display,
you have entered a wrong code number.
Now it is essential to enter the correct code
after the waiting period has elapsed (Cod in
the display).
If the radio is turned off before the waiting
period has elapsed, then the waiting period
restarts as soon as the radio is turned on
again.
Switching the code system off
•Turn off the radio.
•Simultaneously press preset buttons 1
and 4and hold them down.
•Turn the set on.
“Cod” will appear in the display.
•Enter the code number given in the
Blaupunkt car radio passport and con-
firm: See example “Restart following
interruption …”.
The code system is now deactivated.

Boston CC22
18
Amplifier Section
ON/OFF
For switching the set on,
•turn button 1.
Your stereo is now ready for operation.
For switching the set off,
•turn button 1.
Balance Control
UsebuttonAtobalancethe soundimpres-
sion of the right and left channel speaker.
Sound Control
UsetheTONEbuttonBto adjust thesound
according to your personal preference.
Radio Section
Selecting the Desired Waveband
Withyourcarradioyouhavefreechoicefrom
the following wavebands:
FM(ultra-shortwave;frequency-modulated),
MW (medium wave), and LW (long wave).
Selecting FM
•Briefly press the FM•T rocker switch
?.
“FM” lights up on the display =.
Selecting MW or LW
•Briefly press the M•L rocker switch >.
“M” for MW or “L” for LW lights up on
the display =.
For changing between MW and LW:
•Press the M•L rocker switch >once
again.
If nothing else is indicated, the following
operating notes hold for all wavebands.
Tuning in a Station Automatical-
ly
Tuning in the Following Station
•Press the upper part of the rocker
switch / 2.
The car stereo automatically starts
searching for the next station.
Tuning in the Previous Station
•Press the lower part of the rocker
switch / 2.
The car radio automatically starts
searching for the previous station.
If the rocker switch / 2up/down is
kept depressed, the station seek opera-
tion continues to be carried out quickly
in the corresponding direction.
Manual Tuning
All stations can also be tuned in “manually”:
•Press the rocker switch <</>> 3on
the left or the right. The frequency band
is scanned in small steps.
Adjusting the Station Seek
Sensitivity
With this set you can modify the station seek
sensitivity.
If you want to search for strong stations only
(reduced sensitivity):
•Press the lo rocker switch 5until “lo”
lights up on the display <.
If you also like to search for weaker stations
(increased sensitivity):
• Press the lo rocker switch 5until the
“lo” indication <goes off.

19
Boston CC22
DEUTSCH
ENGLISH
ITALIANO
PORTUGUES NEDERLAND
ESPAGÑOL SVENSKA FRANÇAIS
With this set it is possible to increase or
reducetheseektuningsensitivitylevel,which
can be of major help in case of either very
good or only poor reception conditions. For
this, press the lo rocker switch 5for appro-
ximately 8 seconds. The display will either
briefly give you the “H” (High) or “L” (Low)
indication. Change the seek tuning sensitivi-
ty by pressing the lo rocker switch 5for
more than 8 seconds.
Switching from Stereo to Mono
For switching from stereo to mono:
•Press the lo rocker switch 5for more
than two seconds.
For stereo reproduction, the stereo sign
will light up on the display ;.
When switching the unit on, stereo sound
reproduction is adjusted.
When the signal strength gets poor, the set
will automatically switch to mono.
Memorizing a Station
You can memorize a station with each of the
preset buttons @.
ForFM,eachpresetbutton@canbealloca-
tedfourtimes,i.e.fourstationscanbestored
on one button.
Thedisplay9showsyouthecorresponding
assignments (I, II, III stand for first, second,
and third allocation; T stands for Travelstore
(forTravelstoreinformationseethefollowing
chapter)).
For changing the storage level:
•Press the FM•T rocker switch ?.
For storing a station:
•select the storage level (FM only). For
this, press the FM•T rocker switch ?
until display 9either gives you I, II, III
or T.
•Tune in the station (see chapter Auto-
matic/Manual Tuning of Stations)
•Press the desired preset button @until
the broadcast becomes audible again
(approx. 2 seconds).
From display :you can see which
button is currently pressed.
Now the station is stored.
Note:
When tuning in an already stored station,
display :will show the corresponding pre-
set button for approx. five seconds. In addi-
tion, for FM, display 9will also give you the
storage level.
Automatically Storing the Stron-
gest Stations (Travelstore)
WithTravelstore,youhavetheopportunityto
automatically store the next five FM stations
of your local reception area and have them
sorted according to their frequencies. This
feature is of special use while travelling.
•Press the FM•T rocker switch ?for at
least two seconds.
The set searches for the next FM stati-
ons and sorts them on the “T” (Travel-
store) storage level. Once the process
is finished, the car radio tunes in to the
first station.
If required, it is also possible to manually
storeastationontheTravelstorelevel.Ifless
than five stations can be received, the free
buttons are represented by dashes for a
short period of time.
Activating a Stored Station
If required, the memorized stations can be
activated at a keystroke.
•Choose the storage level (only FM).
For this, press the FM•T rocker switch
?until display 9shows I, II or III, or
T.
•Briefly press the corresponding preset
button @.

Boston CC22
20
Briefly Sampling a Station
(Radio Scan)
Starting with the currently tuned in station,
you can have the following ones briefly sam-
pled for approx. eight seconds each.
•Briefly press the Scan knob 1.
If the following station is found, it is
reproduced for approximately eight
seconds. The station’s frequency starts
blinking on display 8; if it has already
been memorized, the corresponding
preset button starts blinking on display
:. In addition, for FM stations, the
storage level indicator lights up on dis-
play 9. Subsequently, the set starts
searching for the next station.
For selecting a sampled station:
•Press the Scan knob 1once again.
The Scan function is off.
After the search operation has been conclu-
ded, and no station has been chosen, the
radio starts playing the station from which
Station Scan was started before.
Sampling Memorized Stations
Allmemorizedstationsofawavebandcanbe
briefly sampled.
•Press the PS rocker switch 4.
One after another, the car radio will
then start introducing all memorized
stations of the selected waveband.
For FM, either the stations of storage
levels I - III or of the Travelstore level
“T” are sampled. This depends on the
current switching status.
If a preset button has no station alloca-
ted, this button is skipped.
To terminate this function:
•Press the PS rocker switch 4once
again.
The station currently sampled is main-
tained.
Tape Section
Inserting a Tape
If you want to listen to a tape:
•Switch on the set.
•Insert the cassette into the slot with the
tape side showing to the right and the
empty reel to the front.
Fast Forwarding the Tape
Fast Forward Operation
• Briefly press the FF button 6.
Stopping Fast Forward Operation
• Briefly press the FF button 6.
Removing the Tape
To stop tape play:
•Press the button 6firmly.
The cassette is ejected.

21
Boston CC22
DEUTSCH
ENGLISH
ITALIANO
PORTUGUES NEDERLAND
ESPAGÑOL SVENSKA FRANÇAIS
Care Notes
We recommend C-60 and C-90 type tapes
for use in any automobile tape player; to
protectyourtapes,storetheminacoolplace
away from dirt, dust, or excessive tempera-
tures above 50°Celsius. In order to ensure
smoothtapeoperation,coldtapesshouldbe
allowed to heat up a bit before they are
played. If dust collects on the audio head or
the rubber roller, problems related to rough
tape operation or poor sound quality may
occur after approx. 100 hours of operation.
For normal contamination, use a head-
cleaning cassette to remove the dust; for
moreintensivecontamination,usea cotton-
wooltipsoakedwithalcohol.Neverusehard
tools!
Appendix
Technical Data
Amplifier:
Output power: 2 x 10 W watts RMS
acc. to DIN 45324/3.1
2 Ω
FM:
Sensitivity: 0.9 µV at 26 dB
signal-to-noise ratio
Frequency
response: 35 - 16 000 Hz (-3 dB)
Tape Section:
Frequency
response: 30 - 14 000 Hz (-3 dB)
Subject to modifications!

13
Boston CC22 (Code deaktiviert)
DEUTSCH
ENGLISH
ITALIANO
PORTUGUES NEDERLAND
ESPAGÑOL SVENSKA FRANÇAIS
Blaupunkt-Werke GmbH
Bosch Gruppe
7/94 K7/VKD 3 D92 147 027 PM