Blaupunkt Laguna CD36 User manual

Radio CD
http://www.blaupunkt.com
Laguna CD36 7 646 085 510
Operating and installation instructions
Notice d’emploi et de montage
Instrucciones de manejo e instalación
Instruções de serviço e de montagem
ጇѰЊཆ
사용 및 장착 설명서
사용 및 장착 설명서
BA_LagunaCD36_cover.indd 1BA_LagunaCD36_cover.indd 1 3/14/06 9:53:44 PM3/14/06 9:53:44 PM

2
3
4
51
2
67
13 12 10 98
11
1BA_LaguCD36_gb 3/14/06, 2:25 PM2

3
FRANÇAIS ENGLISH
ESPAÑOL
PORTUGUÊS
1Button to switch the unit on/off
and to mute the unit.
2Button to release the control
panel.
3CD Eject button .
4Volume control.
5CD-Slot.
6AUDIO button, to adjust the
bass, treble, balance and fader
settings and Sound Preset
7Short press: MENU button, to
open the basic settings menu.
Long press: SCAN, to start scan
function.
8Arrow buttons
9X-Bass button to adjust the X-
Bass function.
:Short press: DIS button, to
display the time.
Long press: to change the dis-
play priority.
;Keys 1 - 6
<Short press: BND button, to se-
lect the FM memory bank
and the AM waveband, source
selection to radio mode.
Long press: TS, to start the
Travelstore function.
=SRC button, to select the CD,
radio and CD changer or AUX
sources.
CONTROLS
1BA_LaguCD36_gb 3/14/06, 2:25 PM3

4
CONTENTS
Notes and accessories ................... 5
Road safety ............................................5
Installation ..............................................5
Accessories ............................................5
International telephone information ........... 5
Detachable control panel ................ 6
Theft protection ...................................... 6
Detaching the control panel ..................... 6
Attaching the control panel ......................6
Switching on/off ............................. 7
Adjusting the volume ...................... 8
Setting the power-on volume ................... 8
Instantaneous volume reduction (mute) ....8
Mute while telephoning ........................... 8
Confirmation beep ..................................9
Radio mode .................................... 9
Switching to radio mode .......................... 9
Setting the tuner ..................................... 9
Selecting the frequency range/ memory . 10
Tuning into a station ..............................10
Storing stations ..................................... 10
Storing stations automatically
(Travelstore) ..........................................11
Listening to preset stations .................... 11
Scanning receivable stations (SCAN) .... 11
Setting the display................................. 11
CD mode ...................................... 12
Switching to CD mode .......................... 12
Selecting tracks ....................................12
Fast searching (audible) ........................ 12
Random play (MIX) ............................... 12
Scanning tracks (SCAN) ....................... 12
Repeating tracks (REPEAT) ................... 13
Pausing playback (PAUSE) ................... 13
Changing the display ............................ 13
Ejecting a CD ....................................... 13
CD changer mode ........................ 14
Switching to CD changer mode ............. 14
Selecting a CD ..................................... 14
Selecting tracks .................................... 14
Fast searching (audible) ........................ 14
Changing the display ............................ 14
Repeating individual tracks or
whole CDs (REPEAT) ........................... 14
Random play (MIX) ............................... 14
Scanning all tracks on all CDs (SCAN) .. 15
Pausing playback (PAUSE) ................... 15
CLOCK - Time ............................... 16
Briefly displaying the time ...................... 16
Setting the time ..................................... 16
Selecting 12/24-hour clock mode .......... 16
Displaying the time continuously
when the unit is off and the ignition is on 16
Briefly displaying the time when the
unit is switched off ................................ 16
Tone and volume distribution
settings ......................................... 17
Adjusting the bass settings .................... 17
Adjusting the treble settings .................. 17
Setting the left/right volume
distribution (balance) ............................. 17
Setting the front/back volume
distribution (fader) ................................. 17
Equalizer and X-BASS .................. 18
Setting the level display ................ 19
External audio sources ................. 19
Specifications ............................... 20
Installation instructions ............... 113
1BA_LaguCD36_gb 3/14/06, 2:25 PM4

5
FRANÇAIS ENGLISH
ESPAÑOL
PORTUGUÊS
Notes and accessories
Thank you for deciding to purchase a
Blaupunkt product. We hope you enjoy
using this new piece of equipment.
Before using the device for the first time,
please read these instructions careful-
ly. The Blaupunkt editors are constant-
ly working on making the operating in-
structions clearer and easier to under-
stand. However, if you still have any
questions on how to operate the unit
please contact your dealer or the tele-
phone hotline for your country. You will
find the hotline telephone numbers print-
ed at the back of this booklet.
Road safety
Road safety has absolute prior-
ity. Only operate your car radio if the
road and traffic conditions allow you
to do so. Familiarise yourself with the
unit before setting off on your jour-
ney.
You should always be able to hear
police, fire and ambulance sirens in
good time from inside your vehicle.
For this reason, listen to your car
sound system at a moderate volume
level.
Installation
If you want to install your car radio your-
self, please read the installation and
connection instructions that follow these
operating instructions.
NOTES AND ACCESSORIES
Accessories
Only use accessories approved by Blau-
punkt.
Remote control
RC-12H is included. You can conve-
niently access the most important func-
tions of your car radio from the steering
wheel via the optional RC08 or RC10.
You cannot switch the device on/off us-
ing the remote control.
Amplifier
All Blaupunkt and Velocity amplifiers can
be used.
CD changer
You can connect the following Blaupunkt
CD changers: CDC A 08, IDC A 09 and
CDC A03.
International telephone
information
If you have any questions regarding the
operation of your car radio or if you re-
quire further information, please do not
hesitate to call us!
The information hotline numbers are
printed on the last page of these instruc-
tions.
1BA_LaguCD36_gb 3/14/06, 2:25 PM5

6
Detachable control panel
Theft protection
As a way of protecting your equipment
against theft, the unit is equipped with
a detachable control panel (release pan-
el). Without this control panel, the car
radio is worthless to a thief.
Protect your equipment against theft by
taking the control panel with you every
time you leave your vehicle. Do not
leave the control panel in your vehicle -
not even in a hidden place.
The control panel has been designed
to be easily use.
Note:
●Never drop the control panel.
●Never expose the control panel to
direct sunlight or other heat sourc-
es.
●Avoid making direct skin contact
with the control panel’s contacts. If
necessary, clean the contacts with
a lint-free cloth and some alcohol.
Detaching the control panel
2
➮Press the button 2.
The control panel locking mechanism
opens.
➮First, pull the control panel straight
off the unit and then out towards
the left.
●The unit switches off after the con-
trol panel is detached.
●All the current settings are saved.
●Any CD already inserted in the unit
remains there.
Attaching the control panel
➮Slide the control panel from left to
right into the unit’s guide.
➮Press the left-hand edge of the
control panel into the unit until it
clicks into place.
Note:
●When attaching the control panel,
make sure you do not press the
display.
If the device was still switched on when
you detached the control panel, it will
automatically switch on again with the
last settings activated (i.e. radio, CD, CD
changer or AUX) when the panel is re-
placed.
DETACHABLE CONTROL PANEL
1BA_LaguCD36_gb 3/14/06, 2:25 PM6

7
FRANÇAIS ENGLISH
ESPAÑOL
PORTUGUÊS
SWITCHING ON/OFF
Switching on/off
There are various ways of switching the
unit on/off:
Switching on/off using the vehicle
ignition
If the unit is correctly connected to the
vehicle’s ignition and it was not switched
off using ON/OFF button 1, it will
switch on/off simultaneously with the
ignition.
Switching on/off using the
detachable control panel
➮Remove the control panel.
The unit switches off.
➮Attach the control panel again.
The unit switches on. The last settings
(radio, CD, CD changer or AUX) will be
reactivated.
Switching on/off using button 1
➮To switch the unit on, press button
1.
➮To switch the unit off, press button
1for longer than two seconds.
The unit switches off.
Note:
●If you switch on the unit when the
ignition is off, the unit will switch off
automatically after one hour to pre-
vent draining of the vehicle battery.
Switching on by inserting a CD
If the unit is switched off and there is no
CD inserted in the drive,
➮gently insert the CD with the print-
ed side uppermost into the drive
until you feel some resistance.
The CD will be drawn automatically into
the drive.
You must not hinder or assist the drive
as it draws in the CD.
The unit switches on. CD playback be-
gins.
Note:
●The unit will remain off if the igni-
tion is off. To turn it on, press but-
ton 1once.
1BA_LaguCD36_gb 3/14/06, 2:25 PM7

8
ADJUSTING THE VOLUME
Adjusting the volume
The volume can be adjusted in steps
from 0 (mute) to 66 (maximum).
➮Increase the volume by pressing
the button 4.
➮Decrease the volume by pressing
the button 4.
Setting the power-on volume
You can set the unit’s default power-on
volume.
➮Press the MENU button 7.
➮Press the or button 8repeat-
edly until “ON VOLUME”appears
in the display.
➮Set the power-on volume using the
and buttons 8.
To help you adjusting the volume more
easily, the audible volume level will in-
crease or decrease accordingly as you
make your changes.
If you select “LAST VOL”, the volume
played before the unit was last switched
off will be reactivated.
Note:
●To protect your hearing, the maxi-
mum switch-on volume under the
“LAST VOL”setting is “38”. If the
volume was higher before the unit
was switched off and “LAST VOL”
has been selected, the volume will
be set at “38”the next time the ra-
dio is switched on.
When you have finished making your
changes,
➮press the MENU button 7twice.
Instantaneous volume reduction
(mute)
This feature allows you to instanta-
neously reduce (mute) the volume to a
level preset by you.
➮Briefly press button 1.
“MUTE”appears in the display.
To restore the volume,
➮press button 1again.
Setting the mute level
You can set the unit’s mute volume lev-
el.
➮Press the MENU button 7.
➮Press the or button 8repeat-
edly until “MUTE LVL”appears in
the display.
➮Set the mute level using the and
buttons 8.
When you have finished making your
changes,
➮press the MENU button 7twice.
Mute while telephoning
If your unit is connected to a mobile tele-
phone, the car radio’s volume will be
muted as soon as you “pick up”the tele-
phone. “PHONE”shows in the display.
This requires the mobile telephone be
connected to the car radio as described
in the installation instructions.
1BA_LaguCD36_gb 3/14/06, 2:25 PM8

9
FRANÇAIS ENGLISH
ESPAÑOL
PORTUGUÊS
ADJUSTING THE VOLUME
Confirmation beep
For some functions you will hear a con-
firmation beep if you keep a button
pressed for longer than two seconds.
For instance, after storing a radio sta-
tion to a station button you will hear a
confirmation beep. The beep can be
switched on/off.
➮Press the MENU button 7.
➮Press the or button 8repeat-
edly until “BEEP”appears in the
display.
➮Use the or buttons 8to
switch between the options.
“OFF”means beep off, “ON”means the
beep is switched on.
➮Press the MENU button 7.
Radio mode
Switching to radio mode
If you are listening to CD, CD changer
or AUX mode,
➮press the BND•TS <button
or
➮press the SRC button =repeated-
ly until “FM”or “AM”(“MW”) ap-
pears in the display.
Setting the tuner
In order to guarantee the perfect func-
tioning of the radio element, the unit
must be set for the region in which you
are located. You can choose between
Europe (EUROPE), America (USA),
Thailand (THAI) and South America
(S-AMERICA). The tuner comes from
the factory set for the region in which
the unit was sold. Should you encoun-
ter problems with radio reception,
please check this setting.
This set of instructions refers to the
“USA”setting.
➮Switch off the device by pressing
button 1.
➮Press and hold down the 1and 5
buttons ;at the same time and
switch on the device again with
button 1.
“TUNER”is displayed.
➮Press the buttons 8within
the next 8 seconds and select your
tuner region.
RADIO MODE
1BA_LaguCD36_gb 3/14/06, 2:25 PM9

10
RADIO MODE
To save the setting,
➮switch the device off and on again
or wait approx. 8 seconds. The ra-
dio starts with the last setting acti-
vated (radio, CD, CD changer or
AUX).
Selecting the frequency range/
memory
This unit can receive programmes
broadcast over the FM andAM frequen-
cy ranges. There are three memory
banks for the FM range and one for the
AM range. Six stations can be stored in
each memory bank.
Selecting the FM memory bank or
the AM frequency range
respectively
➮Press the BND•TS button <to
switch between the FM memory
banks (FM1, FM2 and FMT) and
the AM frequency range respec-
tively.
Tuning into a station
There are various ways of tuning into a
station.
Automatic seek tuning
➮Press the or button 8.
The unit tunes into the next receivable
station.
Setting the sensitivity for station
seek tuning
You can configure the radio to only tune
into stations with a strong reception or
to also tune into those with a weak re-
ception.
➮Press the MENU button 7.
➮Press the or button 8repeat-
edly until “SENS HI”or “SENS LO”
appears in the display.
“SENS HI”means that the tuner is highly
sensitive. “SENS LO”means it is set to
the lower sensitivity setting.
➮Set the required sensitivity using
the or buttons 8.
When you have finished making your
changes,
➮press the MENU button 7.
Note:
●Different seek tuning sensitivities
can be set separately for FM and
AM respectively. To do so, activate
the relevant waveband.
Tuning into stations manually
You can also tune into stations manual-
ly.
➮Press the or button 8.
Storing stations
Storing stations manually
➮Select the required memory bank
(FM1, FM2 or FMT) or the AM fre-
quency range.
➮Tune into the station.
➮Press one of the station buttons
1 - 6 ;for longer than 2 seconds
to store the station to that button.
1BA_LaguCD36_gb 3/14/06, 2:25 PM10

11
FRANÇAIS ENGLISH
ESPAÑOL
PORTUGUÊS
RADIO MODE
Storing stations automatically
(Travelstore)
You can automatically store six stations
with the strongest reception in the re-
gion. The stations are stored in the FMT
or AM memory depending on the se-
lected frequency range.
Note:
●Stations that were previously
stored in this memory are deleted
in the process.
➮Press and hold the BND•TS button
<until the seek tuning starts.
The station storing procedure begins.
“FM TSTORE”or “AM TSTORE”ap-
pears in the display. After the process
is completed, the station that is stored
in location 1of the respective memory
bank will be played.
Listening to preset stations
➮Select the memory bank in which
the station was stored.
➮Press the preset station button
1 - 6 ;of the station you want to
listen to.
Scanning receivable stations
(SCAN)
You can briefly play all the receivable
stations by activating the scan function.
You can set the scanning time to be-
tween 5 and 30 seconds in the menu.
Starting SCAN
➮Keep the MENU button 7pressed
until the scan process starts.
“SCAN”appears briefly in the display
followed by the current frequency (which
flashes).
Stopping SCAN and continuing
listening to a station
➮Press the MENU button 7.
Scanning is stopped and the station that
was tuned into last will remain active.
Setting the scantime
➮Press the MENU button 7.
➮Press the or button 8repeat-
edly until “SCAN TIME”appears in
the display.
➮Set the required scantime using
the or buttons 8.
When you have finished making your
changes,
➮press the MENU button 7twice.
Note:
●The set scantime also applies to
scanning in CD and CD changer
mode.
Setting the display
You can choose to continuous display
one of the followings:
●Band and Time
●Band and Frequency
➮Keep the DIS button :pressed
until the required display appears.
1BA_LaguCD36_gb 3/14/06, 2:25 PM11

12
CD mode
You can use this unit to play standard
CDs, CD-Rs and CD-RWs with a diam-
eter of either 5 or 3 inches.
To ensure the system functions proper-
ly, only use CDs labelled with the com-
pact disc logo. Problems might be ex-
perienced when trying to play copy-pro-
tected CDs. Blaupunkt cannot guaran-
tee the proper functioning of copy-pro-
tected CDs!
Risk of damage to the CD
drive! Contoured CDs (shape CDs)
are not suitable for playback in this
unit.
We accept no liability for any dam-
age to the CD drive or CD that may
occur as a result of the use of un-
suitable CDs.
Switching to CD mode
If there is no CD inserted in the drive
and the unit is playing Radio, CD
Changer or AUX mode,
➮gently insert CD with the printed
side uppermost into the drive until
you feel some resistance.
The CD is drawn into the drive automat-
ically.
You must not hinder or assist the drive
as it draws in the CD.
CD playback begins.
Note:
●The unit will remain off if the igni-
tion is off. To turn it on and play the
inserted CD, press button 1once.
If a CD is already inserted in the drive
and the unit is playing Radio, CD
Changer or AUX mode.
➮Press the SRC button =repeat-
edly until “CD”appears in the dis-
play.
Playback begins from the point at which
it was last interrupted.
Selecting tracks
➮Press one of the arrow buttons 8
to select the next or previous track.
If you press the or button 8once,
the current track will be played again
from the beginning.
Fast searching (audible)
To fast search backwards or forwards,
➮keep one of the buttons 8
pressed until fast reversing / fast
forwarding begins.
Random play (MIX)
➮Press button 5 MIX ;.
“MIX CD”appears briefly in the display
and the MIX symbol lights up. The next
randomly selected track will then be
played.
Stopping MIX
➮Press button 5 MIX ;again.
“MIX OFF”appears briefly in the dis-
play and the MIX symbol disappears.
Scanning tracks (SCAN)
You can briefly play all the tracks on a
CD.
➮Press the MENU button 7for
longer than two seconds.
CD MODE
1BA_LaguCD36_gb 3/14/06, 2:25 PM12

13
FRANÇAIS ENGLISH
ESPAÑOL
PORTUGUÊS
CD MODE
The next track will then be played for
scantime as set in the “Setting the
scantime”.
Note:
●You can set the scantime. For fur-
ther details, please read the sec-
tion entitled “Setting the scantime”
in the “Radio mode”chapter.
Stopping SCAN and continuing
playback
➮To stop scanning, press the MENU
button 7.
The current track will then continue to
be played.
Repeating tracks (REPEAT)
➮If you want to repeat a track, press
button 4 RPT ;.
“RPT TRCK”appears briefly in the dis-
play and the RPT symbol lights up. The
track is repeated until you deactivate
RPT.
Cancelling repeat
➮If you want to stop the repeat func-
tion, press button 4 RPT ;again.
“RPT OFF”appears briefly in the dis-
play and the RPT symbol disappears.
Normal playback is then continued.
Pausing playback (PAUSE)
➮Press button 3 ;.
“PAUSE”appears in the display.
Cancelling pause
➮Press button 3;while in
pause mode.
Playback is continued.
Changing the display
Two options are available:
●Track number and clock.
●Track number and playing time.
➮Press the DIS button :for
longer than two seconds until the
required display appears.
Ejecting a CD
➮Press the button 3.
➮Remove the CD
Notes:
●An ejected CD will be reloaded into
the unit if not removed within 10
seconds to protect it from acciden-
tal damage.
●You may also eject a CD when the
unit is off, or when CD is not play-
ing.
1BA_LaguCD36_gb 3/14/06, 2:25 PM13

14
CD changer mode
Note:
●Information on handling CDs, in-
serting CDs and operating the CD
changer can be found in the oper-
ating instructions supplied with
your CD changer.
Switching to CD changer mode
➮Press the SRC button =repeat-
edly until “CHANGER”appears in
the display.
The CD Changer will resume playback
from where it was last played previous-
ly.
Selecting a CD
➮To move up/ down from one CD to
another, press the or button
8once or several times.
➮An empty CD magazine slot will be
skipped in the CD selection pro-
cess.
Selecting tracks
➮To move up/ down from one track
to another on the current CD, press
the or button 8once or sev-
eral times.
Fast searching (audible)
To fast search backwards or forwards,
➮keep one of the or buttons 8
pressed until fast reversing/fast for-
warding begins.
Changing the display
5 options are available:
●Track number and play time
●Track number and clock
●CD number and track number
●CD number and clock
●CD number and play time
➮Press the DIS button :once or
several times for longer than two
seconds until the required display
appears.
Repeating individual tracks or
whole CDs (REPEAT)
➮If you wish to repeat the current track,
briefly press button 4 RPT ;.
“RPT TRCK”appears briefly and RPT
lights up in the display.
➮If you wish to repeat the current
CD, press button 4 RPT ;longer
than two seconds.
“RPT DISC”appears briefly and RPT
lights up in the display.
Cancelling repeat
➮If you want to stop the repeat func-
tion for the current track or CD,
press button 4 RPT ;briefly and
“RPT OFF”appears briefly in the
display and RPT disappears.
Random play (MIX)
➮To play all the tracks on the current
CD in random order, briefly press
button 5 MIX ;.
“MIX CD”appears briefly and MIX lights
up in the display.
CD CHANGER MODE
1BA_LaguCD36_gb 3/14/06, 2:25 PM14

15
FRANÇAIS ENGLISH
ESPAÑOL
PORTUGUÊS
CD CHANGER MODE
➮To play the tracks on all the insert-
ed CDs in random order, press but-
ton 5 MIX ;longer than two sec-
onds.
“MIXALL”appears briefly and MIX lights
up in the display.
Stopping MIX
➮Press button 5 MIX ;briefly and
“MIX OFF”appears briefly in the
display and MIX disappears.
Scanning all tracks on all CDs
(SCAN)
➮To briefly play all the tracks on all
inserted CDs in ascending order,
press the MENU button 7for
longer than two seconds.
“TRK SCAN”appears briefly follows by
blinking the track number of the CD
track being scanned.
Stopping SCAN
➮To stop scanning, briefly press the
MENU button 7.
The current track will then continue to
be played.
Note:
●You can set the scantime. For fur-
ther details, please read the sec-
tion entitled “Setting the scantime”
in the “Radio mode”chapter.
Pausing playback (PAUSE)
➮Press button 3;.
“PAUSE”appears in the display.
Cancelling pause
➮Press button 3;while in
pause mode.
Playback is continued.
1BA_LaguCD36_gb 3/14/06, 2:25 PM15

16
CLOCK - Time
Briefly displaying the time
➮To display the time, briefly press
the DIS button :.
Setting the time
➮To set the time, press the MENU
button 7.
➮Press the or button 8repeat-
edly until “CLOCK SET”appears in
the display.
➮Press the button 8.
The time appears in the display. The
minutes flash on and off and can be
adjusted.
➮Adjust the minutes using the
buttons 8.
➮Once you have set the minutes,
press the button 8. The hours
start flashing.
➮Adjust the hours using the but-
tons 8.
When you have finished making your
changes,
➮press the MENU button 7twice.
Selecting 12/24-hour clock
mode
➮Press the MENU button 7.
➮Press the or button 8repeat-
edly until “12H MODE”or “24H
MODE”appears in the display.
➮Press the or button 8to
switch between the modes.
When you have finished making your
changes,
➮press the MENU button 7.
Displaying the time continuously
when the unit is off and the
ignition is on
“CLOCK ON”setting in the menu allows
you to display the time when the unit is
off and the vehicle ignition is on,
➮press the MENU button 7.
➮Press the or button 8repeat-
edly until “CLOCK OFF”or
“CLOCK ON”appears in the dis-
play.
➮Press the or button 8to
switch between the ON/OFF set-
tings.
When you have finished making your
changes,
➮press the MENU button 7.
Briefly displaying the time when
the unit is switched off
To briefly display the time when the unit
is off,
➮press the DIS button :.
The time is displayed for eight seconds.
CLOCK - TIME
1BA_LaguCD36_gb 3/14/06, 2:25 PM16

17
FRANÇAIS ENGLISH
ESPAÑOL
PORTUGUÊS
Tone and volume
distribution settings
You can adjust the tone settings (bass
and treble) separately for each source
(radio, CD, CD changer and AUX).
The volume distribution (balance and
fader) settings apply to all audio sourc-
es.
Adjusting the bass settings
➮Press the AUDIO button 6.
“BASS”appears in the display.
➮Press the or button 8to ad-
just the bass.
When you have finished making your
changes,
➮press the AUDIO button 6.
Adjusting the treble settings
➮Press the AUDIO button 6.
“BASS”appears in the display.
➮Press the button 8
repeatedly until “TREBLE”appears
in the display.
➮Press the or button 8to ad-
just the treble.
When you have finished making your
changes,
➮press the AUDIO button 6.
Setting the left/right volume
distribution (balance)
➮To set the left/right volume distribu-
tion (balance), press the AUDIO
button 6.
“BASS”appears in the display.
➮Press the button 8repeatedly
until “BAL”appears in the display.
➮Press the or button 8to
adjust the balance (right/left).
When you have finished making your
changes,
➮press the AUDIO button 6.
Setting the front/back volume
distribution (fader)
➮To set the front/back volume distri-
bution (fader), press the AUDIO
button 6.
“BASS”appears in the display.
➮Press the button 8repeatedly
until “FADER”appears in the dis-
play.
➮Press the or button 8to ad-
just the fader (front/back).
When you have finished making your
changes,
➮press the AUDIO button 6.
TONE AND VOLUME DISTRIBUTION SETTINGS
1BA_LaguCD36_gb 3/14/06, 2:25 PM17

18
Equalizer and X-BASS
X-BASS
X-Bass means increased bass at low
volumes.
You can set the X-Bass in steps rang-
ing from OFF to three. Three means that
the X-Bass boost is set to maximum and
OFF means that X-Bass is switched off.
Note:
●X-BASS setting is shared by all au-
dio source (radio, CD, CD-changer
or AUX).
➮To set the X-BASS, press the
X-BASS 9button.
➮Press the or button 8to
choose between the possible set-
tings.
➮Press the X-BASS 9button once
you have completed the setting.
Selecting a preset sound effect
(EQ)
You can select a preset sound effect for
the following styles of music:
●ROCK
●POP
●CLASSIC
The settings for these music styles have
already been programmed.
To select one of the sound presets,
➮press the AUDIO 6button.
“BASS”appears on the display.
➮Press the button 8repeatedly
until one of the sound effect op-
tions appears on the display.
➮Press the or button 8to
choose between the presets.
If you want to deactivate the sound pre-
set,
➮choose “EQ OFF”from the avail-
able options.
➮Press the AUDIO 6button once
you have completed the setting.
Note:
●The selected preset sound effect is
applied to all audio sources.
EQUALIZER AND X-BASS
1BA_LaguCD36_gb 3/14/06, 2:25 PM18

19
FRANÇAIS ENGLISH
ESPAÑOL
PORTUGUÊS
Setting the level display
The level display briefly provides a sym-
bolic display of the volume and the au-
dio control settings whilst you are ad-
justing them.
When settings are not being made, the
level display indicates the music level
of the car radio.
You can switch the music level display
on/off in the menu.
➮Press the MENU button 7.
“MENU”appears on the display.
➮Press the or button 8repeat-
edly until “PEAK LVL”appears on
the display.
➮Press the or button 8to
choose between “PEAK ON”and
“PEAK OFF”.
When you have finished making your
changes,
➮press the MENU button 7twice.
External audio sources
Instead of connecting a CD changer,
you can connect another audio source
equipped with a line output. The audio
source, for example, can be a portable
CD player, MiniDisc player or MP3 play-
er.
The AUX input must be activated in the
menu.
If you want to connect an external au-
dio source, you will need an adapter
cable. You can obtain this adapter ca-
ble (BP no.: 7 607 897 093) from your
authorised Blaupunkt dealer.
Switching the AUX input on/off
➮Press the MENU button 7.
“MENU”appears in the display.
➮Press the or button 8repeat-
edly until “AUX OFF”or “AUX ON”
appears in the display.
➮Press the or button 8to
switch AUX on/off.
When you have finished making your
changes,
➮press the MENU button 7.
Note:
●If the AUX input is switched on it
can be selected by pressing the
SRC button =and it is shown as
“AUX INPUT”on the display.
LEVEL DISPLAY EXTERNAL AUDIO SOURCES
1BA_LaguCD36_gb 3/14/06, 2:25 PM19

20
Specifications
Amplifier
Output power: 15W RMS x 4ch @ 14.4V @ 4ohm @ 1% THD
Tuner
Frequency ranges USA:
FM: 87.5 - 107.9 MHz (200 kHz step)
AM: 530 - 1710 kHz (10 kHz step)
Frequency ranges Europe:
FM: 87.5 - 108 MHz (100 kHz step auto/50 kHz manual)
AM: 531 - 1602 kHz (9 kHz step)
Frequency ranges Thailand:
FM: 87.5 - 108 MHz (50 kHz step auto/25 kHz step manual)
AM: 531 - 1602 kHz (9 kHz step)
Frequency ranges South America:
FM: 87.5 - 107.9 MHz (100 kHz step auto/50 kHz step manual)
AM: 530 - 1710 kHz (10 kHz step)
FM mono sensitivity:
17 dbf
FM frequency response:
35 - 16,000 Hz
CD
Frequency response:
20 - 20,000 Hz
Pre-amp out
4 channels: 2 V
Input sensitivity
AUX input: 2 V / 6 kΩ
Subject to changes!
SPECIFICATIONS
1BA_LaguCD36_gb 3/14/06, 2:25 PM20