Blaupunkt CR55CHARGE User manual

Owner's Manual
Instrukcja obsługi
Návod k použití
Navodila za uporabo
Használati útmutató
Upute za upotrebu
Instrucțiune de deservire
Инструкция за употреба
Οδηγίες χρήσης
Kasutusjuhend
Naudojimo instrukcijos
Užívateľská príručka
Alarm clock radio with USB and wireless charging
CR55CHARGE

Important Notes
Ÿsafety and operating instruction should be retained for future reference.
ŸThe apparatus should not be exposed to dripping or splashing or placed in a humid
atmosphere such as a bathroom.
ŸDo not install the product in the following areas:
ŸPlaces exposed to direct sunlight or close to radiators.
ŸOn top of other stereo equipment that radiate too much heat.
ŸBlocking ventilation or in a dusty area.
ŸAreas where there is constant vibration.
ŸHumid or moist places.
ŸDo not place near candles or other naked flames.
ŸOperate the product only as instructed in this manual.
ŸBefore turning on the power for the first time, make sure the power adaptor is properly
connected.
For safety reasons, do not remove any covers or attempt to gain access to the inside of the
product. Refer any servicing to qualified personnel.
Do not attempt to remove any screws, or open the casing of the unit; there are no user serviceable
parts inside. Refer all servicing to qualified service personnel.
SAFETY INSTRUCTIONS
1.Read Instructions - All the safety and operating instructions must be read before the product is
operated.
2. Retain Instructions - The safety and operating instructions should be kept with the product for
future reference.
3. Heed warnings - All warnings on the product and in the operating instructions should be
adhered to.
4. Follow instructions - All operating and users' instructions should be followed.
5. Installation - Install in accordance with the manufacturer's instructions.
6. Power sources - This product should be operated only from the type of power source indicated
by the marking adjacent to the power cord entry. If you are not sure of the type of power supply to
your home, consult your product dealer or local power company.
7. Water and moisture - To reduce the risk of fire or electric shock, do not expose the product to
train, dripping, splashing or excessive moisture such as in a sauna or bathroom. Do not use this
product near water, for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet
basement or near a swimming pool (or similar).
8. Object and Liquid Entry - Never push objects of any kind into this product through openings, as
they may touch dangerous voltage points or short-circuit parts that could result in a fire or
electric shock. Never spill liquid of any kind on the product. Do not place any object containing
liquid on top of the product.
9. Servicing - Do not attempt to service this product yourself, as opening or removing covers may
expose you to dangerous voltage or other hazards. Refer all servicing to qualified service
personnel.
10. Replacement parts - When replacement parts are required, ensure that the service technician
has used replacement parts specified by the manufacturer or have the same characteristics as the
original part. Unauthorized substitutions may result in fire, electric shock or other hazards.
11. The highest environmental temperature suitable for this product is 35°C.
12. ESD hints - If the product maybe reset or not reset to operation of control due to electrostatic
discharge, just switch off and reconnect again, or move the product to another location.
13. Battery
a. The batteries must not be exposed to excessive heat such as sunshine, fire or the like.
b. The batteries should be drawn to the environmental aspects of battery disposal.
1

c. Battery usage CAUTION-to prevent battery leakage which may result in body injuries,
property damage, or damage to the apparatus:
. Install all batteries correctly, + and – as marked on the apparatus.
. Do not mix batteries (old and new or carbon and alkaline, etc.)
. Remove batteries when the unit is not used for a long time.
ERP2 (Energy Related Products) note
This product with ecodesign complies with the stage 2 requirements of Commission Regulation
(EC) NO. 1275/2008 implementing Directive 2009/125/EC regard to standby and off mode electric
power consumption of electronic household and office equipment.
WARNING
This appliance is not intended for use by persons (including children) with reduced physical
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their
safety. Children should be supervised to ensure that they do not play with the appliance.
1. Never use the device unsupervised! Switch off the device whenever you are not using it, even if
this only for a short while.
2. The appliance is not intended to be operated by means of an external timer or separate remote
control system.
3. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid a hazard.
4. Before operating this system, check the voltage of this system to see if it is identical to the
voltage of your local power supply.
5. To prevent fire or shock hazard, do not expose this equipment to hot places, rain, moisture or
dust.
6. Do not place this unit close to a strong magnetic field.
7. Do not place the unit on a amplifier or receiver.
8. Do not place this unit in a damp area as the moisture will affect the life of electric components.
9. If the system is brought directly from a cold to a warm location, or is placed in a very damp
room, moisture may condense on the lens inside the player. If this occurs, the system will not
operate properly. Please leave the system turned on for about an hour until the moisture
evaporates.
10. Do not attempt to clean the unit with chemical solvents as this might damage the finish. Wipe
with a clean, dry or slightly damp cloth.
NOTICE
Conformity
Hereby, Blaupunkt Competence Center 2N-Everpol Sp. z o.o., declares that this equipment is in
compliance with the essential requirement and other relevant provisions of Directive
2014/53/EU. Declaration of conformity can be obtained from the product page at
www.blaupunkt.com.
Responsible party: 2N-Everpol Sp. z o.o, Puławska 403A, 02-801 Warsaw, Poland, Phone: +48 22
331 99 59, E-mail: [e-mail]
Your products is designed a manufactured with high quality materials and components, which
can be recycled and reused.
2

3
When this crossed-out wheeled bin symbol is attached to a product it means that the product
is covered by the European Directive 2012/19/EU. Please inform yourself about the local
separate collection system for electrical and electronic products. Please cat according to your
local rules and do not dispose of your old products with your normal household waste. Correct
disposal of your old product helps to prevent potential negative consequences for the
environment and human health.
Your product contains batteries covered by the European Directive 2006/66/EC, which cannot
be dispose with normal household waste. Please inform yourself about the local rules on
separate collection of batteries because correct disposal helps to prevent negative
consequences for the environmental and human health.
Environmental information
All unnecessary packaging has been omitted. We have tried to make the packaging easy to
separate into three materials: cardboard (box),polystyrene foam(buffer) and poly ethylene
(bags, protective foam sheet). Your system consists of material which can be recycled and
reused if disassembled by a specialized company. Please observe the local regulations
regarding the disposal of packaging materials, exhausted batteries and old equipment.
Recording and playback of material might require consent. See Copyright Act 1956 and The
Performer's Protection Acts 1958 to 1972.

4
Many thanks to purchase our model, please read and reference this manual carefully before
operate the unit. Please keep the manual for future operation reference.
Control locations
1-alarm 1 on icon; 2-radio/sleep button;
3-alarm 1- 2 on/off button; 4-clock set/memory button;
5-Down button; 6-alarm 2 on icon;
7-mood light; 8-sleep on icon;
9-snooze button; 10-dimmer button;
11-wireless charging indicator; 12-volume set button;
13-up button; 14-PM indicator;
15-Wireless charging center; 16-USB charge port;
17-DC IN jack;
18-Backup battery compartment(CR2032, not included)
Install backup battery power: Place your clock radio face down on a flat and soft surface; use
a coin to turn the battery cover anti-clockwise at the back of your unit; insert one new lithium
cell “CR2032” battery(not included) into the battery compartment by observing the “+” polarity
facing upward; replace the battery cover and turn clockwise to lock it. The time and all setting
will be kept in case of AC power interrupted, but the backup battery is available.
Remark: Do not use old or used battery; do not use rechargeable battery; new battery is
recommended for optimal usage of this clock.
Unit power on: insert the power connector into the DC jack of the unit, and plug in the AC/DC
adaptor to an AC household outlet in order to get the power; then the display will light on.
Clock time setting: Short press the set button, the hour digit will flicker on the display, press
the up or down button to adjust the desired hour, press and hold the up or down button to
accelerate setting at high speed; Short press the set button again skip to the minute setting.
Using the same method like the hour setting to operate the rest setting for minute/snooze
time( 5 min to 60 min)/time format(12 or 24 hours). Short press the set button to finish the
setting, and clock time will become stable on display.

5
Alarm setting: press and hold the alarm1-2 on/off button till the hour digits flare on display,
and the alarm 1 icon LED will light on at same time; press the up or down button to adjust the
desired hour, press and hold up or down button to accelerate setting at high speed; short press
the alarm1-2 on/off button again skip to the minute setting, press the up or down button to
adjust the desired minute; short press the alarm1-2 on/off button again skip to the alarm
source selection, press the up or down button to select alarm source between buzz or radio(if
radio was selected as alarm source; press the alarm1-2 on/off button skip to alarm 2 setting
which is same operation as alarm 1.
Alarm on/off: you need turn on the alarm after finished above alarm setting; press the alarm 1-
2 on/off button repeatedly can turn on or off alarm 1 and alarm 2. Please make sure the relative
alarm LED will light on after you selected which means the alarm is working now.
Alarming and snooze: when unit is sounding due to the alarm time is being, press the alarm 1-
2 on/off button to cancel the voice, and will wake up again at the same time of next day; if you
press the snooze button, the alarm will be silenced momentarily and come on again after the
set snooze duration.
Note:
1.The unit will exist the clock or alarm setting mode when no key is pressed in approximate 10
seconds.
2.if your second alarm is activate while the first alarm is sounding or it is in the snooze mode,
the second alarm overrides the first alarm (the first alarm is reset to come on the next day).
3.The alarm only works when the DC/AC power adaptor is connected. Please double check the
alarm setting in case of power interrupted.
Radio
Before listen to the radio, please extend the wire antenna and move the unit next to the
window as you can in order to get better reception. Short press the radio button to turn on or
off the radio mode; press the volume set button first, then continue to press the up or down
button immediately for the output volume adjustment.
Tuning and auto scan: short press the up or down button to tune the radio frequency per
0.1MHz; press and hold the up or down button to scan and play the available station.
Manual memory station: When you tuned a favorite station, press and hold the memory
button till the “PXX” flare on display, press the up or down button to select the preset station
number you desire to save, press the memory button again to confirm. Then the radio station
will be saved.
Pick up preset station: short press the memory button first, press the up or down button to
select the preset station number for listening.
Sleep: in radio listening mode, press and hold the sleep button first, and short press the sleep
button immediately to select the sleep time (05, 10, 15, 30, 45, 60, 75, 90 or OFF); the unit will
revert to clock interface after few seconds, press and hold the sleep button again can check the
remaining sleep time. And the radio listening will auto off when the sleep time is being.
Note: the radio station will have few impacts due to signal interference create by USB or
wireless charging output. You can turn down the volume, or switch to strong signal station for
listening.
Display dimmer and mood light: short the press the dimmer button to adjust the brightness
in high/low/off level; press and hold dimmer button to turn on or off the mood light.
Wireless charging
Center your mobile device with back side down on the top panel marked charging center. The
wireless charging indicator is on which means the clock radio is wireless charging your mobile
device.

6
Wireless charging operation and correction table.

Charging
indicator
Status
Mobile
device
position
Top view
Light on, mobile device is
charging properly.
Make sure your mobile device is
aligned to this units's charging
area. Center your mobile device
with back side down on the top
panel marked charging center.
Mobile device
Light is off,your mobile device is:
1.removed from charging surface.
2.Not placed on the charging
surface properly.
3.When the clock raido is not
connected to a power outlet.
Please verify your mobile device is
not shifted too far off center.
Lift up the mobile device from the
charging surface and put it back
on properly,
Wireless
charging center
Light is flasing when not charging
properly due to general error.
Do not place foreign materials,
such as metal objects, and
magnetic stripe cards between
the mobile device and wireless
charger under charging.
Do not place any
foreign
objects(metal)
on the charging
center or under
mobile device
during charging.

7
Note:
1.This function only works with mobile devices that support Qi technology. Please make sure
your mobile device has included such feature.
2.Make sure your clock radio is connected with the adaptor (5V-2.5A) supplied with this clock
radio. Unauthorized chargers or adaptors may cause damage or the wireless charger may
malfunction.
3.If your mobile device is not charging, the charging indicator is off. Please verify that your
mobile device is not shifted too far off center.
4.Using the external wireless charging receiver connected to non-Qi compatible mobile device
may result in unstable charging.
5.Do not put any foreign object (metal) on the charging area any time or under the mobile
device during charging. The wireless charging indicator flashes and charging will stop.
6.Do not place a wireless charging receiver solely on the wireless charging surface. Doing so
may overheat the wireless charger and cause a fire. It may also result in serious burn or device
malfunction.
7.If you place a mobile device on the wireless charging surface for an extended period, the
wireless charger may overheat and stop charging.
8.Do not cover or block the heat release vent at the back of the clock radio.
9.When the mobile device is fully charged, remove it from the wireless charging surface.
10.Do not place foreign materials, such as metal objects, magnets, magnetic stripe cards,
paper clips etc. between the mobile device and the wireless charging surface. The mobile
device may not charge properly or may be damaged due to overheating.
11.Wireless charging may not work properly if you attach a thick case to your mobile device. If
your case is thick, remove it before placing your mobile device on the wireless charging
surface.
12.If you connect a charger to the mobile device during wireless charging, the wireless
charging feature will be unavailable.
USB charging: Connect the charging cable of your mobile phone to the A-type USB port at the
back of the unit, then connect the other end to your mobile phone. The clock radio will charge
the mobile phone automatically.
Note :
1.Make sure the original cable of your mobile phone's original charging cable for charging
2.Make sure the original adaptor (5V-1.2A) enclosed with your clock radio is being used to
power your clock radio. Using other adaptors may not charge your phone.
3.iPad and Notepad charging is not applicable.
4. Charging one mobile device by the USB port and another mobile device by the wireless
charger at the same time will reduce the charging efficiency and extend the charging time.
Trouble shooting
If your clock displays irrelevant time or does not function properly, which maybe caused by
electro-static discharge or other interference. Unplug the DC jack at the back of the unit, slide
open the battery cover and take out the batteries. Then re-plug the DC jack and reinstall
batteries by observing the correct +/- polarity. Your unit will be reset to default settings and
you need to set it again.

8
Specification
Alarm duration Buzzer 5 minutes/ Radio 1 hour
Snooze duration 5 to 60 minutes
Default settings:-
Time 24HR format
Alarm 1 and 2 6:00am (OFF)
Snooze duration 05 (5 minutes)