Blaupunkt CR60BT User manual

Owner's Manual
Instrukcja obsługi
Návod k použití
Navodila za uporabo
Használati útmutató
Upute za upotrebu
Instrucțiune de deservire
Инструкция за употреба
Οδηγίες χρήσης
Kasutusjuhend
Naudojimo instrukcijos
Užívateľská príručka
Clock radio with Bluetooth
CR60BT
Užívateľská príručka

Important Notes
Ÿsafety and operating instruction should be retained for future reference.
ŸThe apparatus should not be exposed to dripping or splashing or placed in a humid
atmosphere such as a bathroom.
ŸDo not install the product in the following areas:
ŸPlaces exposed to direct sunlight or close to radiators.
ŸOn top of other stereo equipment that radiate too much heat.
ŸBlocking ventilation or in a dusty area.
ŸAreas where there is constant vibration.
ŸHumid or moist places.
ŸDo not place near candles or other naked flames.
ŸOperate the product only as instructed in this manual.
ŸBefore turning on the power for the first time, make sure the power adaptor is properly
connected.
For safety reasons, do not remove any covers or attempt to gain access to the inside of the
product. Refer any servicing to qualified personnel.
Do not attempt to remove any screws, or open the casing of the unit; there are no user serviceable
parts inside. Refer all servicing to qualified service personnel.
SAFETY INSTRUCTIONS
1.Read Instructions - All the safety and operating instructions must be read before the product is
operated.
2. Retain Instructions - The safety and operating instructions should be kept with the product for
future reference.
3. Heed warnings - All warnings on the product and in the operating instructions should be
adhered to.
4. Follow instructions - All operating and users' instructions should be followed.
5. Installation - Install in accordance with the manufacturer's instructions.
6. Power sources - This product should be operated only from the type of power source indicated
by the marking adjacent to the power cord entry. If you are not sure of the type of power supply to
your home, consult your product dealer or local power company.
7. Water and moisture - To reduce the risk of fire or electric shock, do not expose the product to
train, dripping, splashing or excessive moisture such as in a sauna or bathroom. Do not use this
product near water, for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet
basement or near a swimming pool (or similar).
8. Object and Liquid Entry - Never push objects of any kind into this product through openings, as
they may touch dangerous voltage points or short-circuit parts that could result in a fire or
electric shock. Never spill liquid of any kind on the product. Do not place any object containing
liquid on top of the product.
9. Servicing - Do not attempt to service this product yourself, as opening or removing covers may
expose you to dangerous voltage or other hazards. Refer all servicing to qualified service
personnel.
10. Replacement parts - When replacement parts are required, ensure that the service technician
has used replacement parts specified by the manufacturer or have the same characteristics as the
original part. Unauthorized substitutions may result in fire, electric shock or other hazards.
11. The highest environmental temperature suitable for this product is 35°C.
12. ESD hints - If the product maybe reset or not reset to operation of control due to electrostatic
discharge, just switch off and reconnect again, or move the product to another location.
13. Battery
a. The batteries must not be exposed to excessive heat such as sunshine, fire or the like.
b. The batteries should be drawn to the environmental aspects of battery disposal.
1

c. Battery usage CAUTION-to prevent battery leakage which may result in body injuries,
property damage, or damage to the apparatus:
. Install all batteries correctly, + and – as marked on the apparatus.
. Do not mix batteries (old and new or carbon and alkaline, etc.)
. Remove batteries when the unit is not used for a long time.
ERP2 (Energy Related Products) note
This product with ecodesign complies with the stage 2 requirements of Commission Regulation
(EC) NO. 1275/2008 implementing Directive 2009/125/EC regard to standby and off mode electric
power consumption of electronic household and office equipment.
WARNING
This appliance is not intended for use by persons (including children) with reduced physical
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their
safety. Children should be supervised to ensure that they do not play with the appliance.
1. Never use the device unsupervised! Switch off the device whenever you are not using it, even if
this only for a short while.
2. The appliance is not intended to be operated by means of an external timer or separate remote
control system.
3. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid a hazard.
4. Before operating this system, check the voltage of this system to see if it is identical to the
voltage of your local power supply.
5. To prevent fire or shock hazard, do not expose this equipment to hot places, rain, moisture or
dust.
6. Do not place this unit close to a strong magnetic field.
7. Do not place the unit on a amplifier or receiver.
8. Do not place this unit in a damp area as the moisture will affect the life of electric components.
9. If the system is brought directly from a cold to a warm location, or is placed in a very damp
room, moisture may condense on the lens inside the player. If this occurs, the system will not
operate properly. Please leave the system turned on for about an hour until the moisture
evaporates.
10. Do not attempt to clean the unit with chemical solvents as this might damage the finish. Wipe
with a clean, dry or slightly damp cloth.
NOTICE
Conformity
Hereby, Blaupunkt Competence Center 2N-Everpol Sp. z o.o., declares that this equipment is in
compliance with the essential requirement and other relevant provisions of Directive
2014/53/EU. Declaration of conformity can be obtained from the product page at
www.blaupunkt.com.
Responsible party: 2N-Everpol Sp. z o.o, Puławska 403A, 02-801 Warsaw, Poland, Phone: +48 22
331 99 59, E-mail: [e-mail]
Your products is designed a manufactured with high quality materials and components, which
can be recycled and reused.
2

3
When this crossed-out wheeled bin symbol is attached to a product it means that the product
is covered by the European Directive 2012/19/EU. Please inform yourself about the local
separate collection system for electrical and electronic products. Please cat according to your
local rules and do not dispose of your old products with your normal household waste. Correct
disposal of your old product helps to prevent potential negative consequences for the
environment and human health.
Your product contains batteries covered by the European Directive 2006/66/EC, which cannot
be dispose with normal household waste. Please inform yourself about the local rules on
separate collection of batteries because correct disposal helps to prevent negative
consequences for the environmental and human health.
Environmental information
All unnecessary packaging has been omitted. We have tried to make the packaging easy to
separate into three materials: cardboard (box),polystyrene foam(buffer) and poly ethylene
(bags, protective foam sheet). Your system consists of material which can be recycled and
reused if disassembled by a specialized company. Please observe the local regulations
regarding the disposal of packaging materials, exhausted batteries and old equipment.
Recording and playback of material might require consent. See Copyright Act 1956 and The
Performer's Protection Acts 1958 to 1972.
The Bluetooth® wordmark and logos are registered trademarks owned by Bluetooth SIG, lnc.
and any use of such marks by us is under license. Other trademarks and trade names are those
of their respective owners.

4
Many thanks to select our model, please read and reference this manual carefully before
operation. Please keep the manual for future operation reference.
Control locations
1- Set button; 2- Alarm1 button; 3- Alarm2 button; 4- Display; 5 -Previous button;
6-Next button; 7- Play/pause button; 8- DC IN jack; 9- Bass reflex;
10- Backup battery compartment; 11- Antenna; 12- Standby button; 13 - Sleep button;
14- Mode/dimmer button;
Power on clock radio
Insert the AC/DC adaptor to any 230V AC household outlet. Then insert the DC jack to the
backside of the unit. The display will light up and ready to work. Short press the standby button to
enter radio or standby mode; long press the standby button to power off(display off )/on the unit.
Backup battery installation
The radio requires 1 x CR2025 type battery(not included) to provide backup power for setting
memory in the event of a temporary power interruption.
Place the unit face down on a flat and soft surface; use a coin to turn the battery cover under anti-
clockwise direction at the back of the unit; insert one new cell CR2025 battery into the battery
compartment by observing the “ +” polarity facing upward; Replace the battery cover and turn to
clockwise direction to lock it. The time and all settings will be kept in case of AC power
interrupted, but the backup battery is available.
Please kindly disposal the power-exhausted battery in environmental friendly way accord to your
local government requirements. Make sure a fresh CR2025 battery is used, and a fresh battery
could backup clock continuously for around 3weeks.
Display brightness adjustment/Dimmer: long press(2 seconds) mode button repeatedly to
switch and select the display brightness between high/low/off level.
Clock time setting: In standby mode, short press the set button to select 12/24 hours format.
Long press(2 seconds) the set button to start time setting procedure, and the hour digits will flare
on display. Press previous/next button to adjust the desired hour, press and hold it to accelerate
the adjustment in high speed. Short press play/pause button to confirm and skip to minute
setting. Press previous/next button to adjust it, then press play/pause button to finish it.

5
Alarm setting: in standby mode, long press (2 seconds) alarm1 button to start alarm setting
procedure, and the hour digits will flare on display, Press previous/next button to adjust the
desired hour, press and hold it to accelerate the adjustment in high speed. Short press
play/pause button to confirm and skip to minute setting. By using the same mothed to finish the
rest setting for minute/alarm source/alarm volume(between 15~30 level) selection, and press
play/pause button to finish it. Short press alarm1 button to turn on the alarm1. A bell1 icon will
show on the right top corner of display ,which means the alarm1 is working now.
Alarm on/off: you need turn on the alarm after finished the alarm setting. Press alarm1 or alarm2
button repeatedly can turn on or off alarm1 and alarm2. Please make sure the relevant alarm icon
LED will light on display after your selection.
Alarming and snooze: when unit is sounding due to the alarm time is being, press the standby
button to cancel the voice, and will wake up again at the same time of next day; if you rotate the
volume knob, there will activate the snooze function. The alarm will silence temporarily and wake
up again after 9 minutes. Rotate the volume knob again can check the remained snooze time on
display; Press down the volume knob can cancel the snooze function.
Note:
1. The alarm2 setting procedure is similar to alarm1, but long press(2 seconds) alarm1 button for
starting.
2. The unit will exist the clock or alarm setting mode when no key pressed in approximate 5
seconds.
3. If your second alarm activate while the first alarm is sounding or it is in the snooze mode, the
second alarm overrides the first alarm (the first alarm will reset to come on the next day).
4. The alarm only works when the DC/AC power adaptor is connected. Please double check the
alarm setting in case of power interrupted.
5. The alarm voice duration time is 1 hour. FM radio and buzz is available to select as alarm source.
Radio operation
Before listen to the radio, please fully extend the antenna and move the unit next to the window
in order to get better FM reception. Short press the standby button turn on/off the radio. Rotate
the volume knob to adjust the output volume level.
All-in-one scan(auto scan and save as preset station): long press(2 seconds) the play/pause
button to scan and save the available station automatically, max supported up to 60 preset
stations. Short press the previous/next button to select and switch the preset station. Short press
play/pause button can mute the sound, press it again to resume the output.
Auto tune: long press(2 seconds) the previous or next button to auto tune the available station
in upward or downward frequency, and play it automatically.
Manual memory station: Short press the set button first, press the previous or next button
repeatedly and immediately to tune the available station by step and step under 0.1MHz. In case
you tuned the favorite station, short press the set button immediately again, then the current
station will be saved automatically. The preset station number will be sequenced accord low to
high radio frequency automatically.
Repeat above operation to manual save other station.
Remove noise or weak preset station: long press the set button(2 seconds) can remove the
current playing preset station, and the next preset will forward and replace it.
Bluetooth operation
This product includes Bluetooth function which can wireless playback the music from other
Bluetooth device (like smart phone, tablet etc).
1. Press standby button to power on the unit, and short press mode button enter to Bluetooth
model. The Bluetooth symbol will flare on display which means the unit is ready to pair.

6
2. Enable the Bluetooth function on your device, and search the available device (please
reference your device manual for operation), then check the available Bluetooth device on the
list. Select “ BP CR60” for pairing, and the Bluetooth symbol will stable on display after paired
successful.
3. Select and play the music from your Bluetooth device, adjust the volume level on your device
and radio side, then the sound will wireless play and come out from the speaker.
4. Press the previous/next button can select last and next track; press play/pause button can play
or pause the playback; Long press (2seconds) the play/pause button can quit the current
Bluetooth device connection, but ready to pair device.
Notices:
1. All Bluetooth devices are not guaranteed for pairing successfully due to different design and
brand.
2. The best working distance of Bluetooth is within 10 meters without any obstacle in between.
3. The unit only can pair and work with one Bluetooth device in one time.
4. In case of an incoming phone call during Bluetooth playback; the music will stop temporary,
and resume to playback after end the phone call.
Sleep: in audio mode(FM radio or Bluetooth), short press sleep button repeatedly to switch the
sleep time between 5/10/15/30/60/off. Select your desired sleep time and keep it for a while to
activate the sleep function. The unit will off and switch to standby mode automatically in case of
the sleep time is being. Press and hold the sleep button can check the remained sleep time on
display.
Trouble shooting
1. The speaker cannot turn on.
a. Please check if the power connection is correct.
2. No sound output.
a. Please try to adjust the volume knob, and check the play source.
b. please contact service center for support if the issue remained.
3. Background noise on FM station.
a.try to move the unit in other place for better reception.
b. scan and switch to other station for listening.
4. Intermittent sound output in Bluetooth mode
a. Please try to move your Bluetooth device more close to the radio.
b. Please reference the manual for re-pairing.
5. the sound output is too small in Bluetooth mode.
a. Please check the volume level your Bluetooth device and radio both.
Specification
Power source: DC IN 5V/1.2A
FM frequency: 87.5~108.0MHz
Bluetooth version: V5.0
Backup battery power: CR2025, 3V/150mAH(not included)
Power consumption: 5W
Standby power consumption: <1W
Alarm duration: 1 hour
Snooze duration : 9minutes
Default settings:-
Time: 24HR format
Alarm 1 and 2 7:00am (OFF)
(The above spec may update without priority notice.)

7
Power adaptor information
Information published
Value and precision
Unit
Manufacturer's name or trade
mark
Commercial registration
number Address
Shenzhen Fushigang Technology Co., Ltd
Building 8, Shiguan Industrial Park,
Shangcun Community, Gongming
Street,Guangming District,Shenzhen,
GuangDong,China
Model identifier
AS0601A-0501200EUL
Input voltage
100-240
V
Input AC frequency
50/60
Output voltage
DC5
Output current
1.2
Output power
6.0
Average active efficiency
Efficiency at low load (10 %)
No-load power consumption
Hz
V
A
W
%
%
W
68%
≥75
≤0. 1

8
Ważne informacje
ŸNależy zachować instrukcję obsługi oraz informacje dotyczące bezpieczeństwa w celu
wykorzystania ich w przyszłości.
ŸNie należy dopuszczać do tego, aby na urządzenie kapała lub wylewała się ciecz. Nie
wolno też używać go w wilgotnych miejscach, jak np. łazienka.
ŸNie wolno instalować tego urządzenia w następujących miejscach:
ŸWystawionych na bezpośrednie działanie promieni słonecznych lub w pobliżu
grzejników.
ŸKłaść go na wierzchu innego sprzętu stereofonicznego który wydziela ciepło.
ŸBlokując wentylację lub w zapylonym miejscu.
ŸW miejscach narażonych na ciągłe drgania.
ŸW miejscach o wysokiej wilgotności.
ŸNie wolno stawiać urządzenia w pobliżu świec lub otwartego ognia.
ŸUrządzenia można używać wyłącznie w sposób opisany w niniejszej instrukcji.
ŸPrzed pierwszym włączeniem zasilania należy upewnić się, że zasilacz został prawidłowo
podłączony.
Ze względów bezpieczeństwa nie należy demontować obudów ani uzyskiwać dostępu do
wnętrza urządzenia. Urządzenie powinno być naprawiane przez wykwalifikowany personel
serwisu.
Nie wolno rozkręcać urządzenia ani otwierać jego obudowy, gdyż wewnątrz nie ma żadnych
części, które mogłyby być naprawiane przez użytkownika. Konserwacją i naprawą sprzętu
zajmują się wyłącznie wykwalifikowani pracownicy serwisu.
INSTRUKCJE DOTYCZĄCE BEZPIECZEŃSTWA
1. Przeczytać instrukcje — przed korzystaniem z urządzenia należy przeczytać całość
instrukcji obsługi oraz informacje o bezpieczeństwie.
2. Zachować instrukcje — należy zachować instrukcje użytkowania i obsługi w celu
wykorzystania ich w przyszłości.
3. Przestrzegać ostrzeżeń — należy postępować zgodnie z wszystkimi ostrzeżeniami
zamieszczonymi na urządzeniu oraz zgodnie z instrukcją obsługi.
4. Przestrzegać instrukcji — należy postępować zgodnie z instrukcją obsługi oraz
wskazówkami dla użytkownika.
5. Instalacja — należy ustawić urządzenie zgodnie z instrukcjami producenta.
6. Źródła zasilania – urządzenie powinno być zasilane wyłącznie ze źródeł o parametrach
podanych na oznaczeniach na kablu zasilania. Jeżeli użytkownik nie jest pewien, jakiego
rodzaju zasilaniem dysponuje w domu, powinien skontaktować się ze sprzedawcą urządzenia
lub lokalnym dostawcą energii elektrycznej.
7. Woda i wilgoć — aby zmniejszyć zagrożenie pożarem lub porażeniem elektrycznym, nie
wolno narażać urządzenia na bezpośrednie działanie deszczu, wody i wilgoci, jak np. w saunie
czy w łazience. Nie używać niniejszego urządzenia w pobliżu wody, na przykład obok wanny,
umywalki, zlewu kuchennego lub balii, w wilgotnej piwnicy lub w pobliżu basenu (lub w
podobnych miejscach).
8. Przedmioty i ciecze w urządzeniu — nie należy wciskać jakichkolwiek przedmiotów przez
otwory urządzenia, ponieważ mogą one zetknąć się z punktami niebezpiecznego napięcia i
podzespołami, co może wywołać pożar lub porażenie prądem. Pod żadnym pozorem nie
należy rozlewać jakichkolwiek cieczy na powierzchni urządzenia. Nie wolno kłaść na
wierzchu urządzenia przedmiotów zawierających ciecze.