Blaupunkt Bluebot PRECISION Plus User manual

BLUEBOT PRECISION PLUS
EN USER MANUAL 2
DE BEDIENUNGSANLEITUNG 28
FR MANUEL DE L'UTILISATEUR 54
NL GEBRUIKERSHANDLEIDING 80
ALL DISPOSAL & RECYCLING 106
Enjoy it.

2
Welcome!
Thank you for choosing the Blaupunkt Bluebot PRECISION Plus.
With this manual we would like to support you in the set-up and usage of
your Blaupunkt Bluebot robot.
For extra how-to videos, tips & tricks, FAQs or contact details, go to:
https://blaupunktrobotics.eu/support-bluebot/
or
In this manual you will nd the following topics to support you in the set-
up of your robot:
1 Safety regulations.......................................................................... 03
2 Product information ...................................................................... 05
3 Installation of the robot & auto station ...................................... 07
4 Installation of the Bluebot application .........................................11
5 Usage of the robot & auto station ................................................13
6 Cleaning settings ............................................................................16
7 Maintenance ...................................................................................17
8 Basic parameters ............................................................................23
9 Usage limitations ........................................................................... 24
10 Troubleshooting ............................................................................ 25
11 Warranty ......................................................................................... 27
FOREWORD
Blaupunkt Robotics Youtube Channel

3
EN
1. SAFETY REGULATIONS
WARNING:
· Use only the original rechargeable battery and charging station specially equipped
by the manufacturer. Non-rechargeable batteries are strictly prohibited, please refer
to "product parameters" for battery specication information.
· It is forbidden to use the product in environments with open ames or fragile
objects.
· It is forbidden to use the product in extremely hot (above 40 °C) or extremely cold
(below 0 °C) environments.
· It is forbidden to use the products near burning or evenly hot object, for example a
burning replace.
· Do not use this product in high temperature environments.
· It is forbidden to approach the opening and operating parts of the robot with
ngers, clothes, hair and any item for safety reasons.It is forbidden to use the products
on wet or uneven ground.
· It is forbidden for the product to absorb any articles such as stones and waste paper
that may clog the product.
· It is forbidden for the product to absorb any inammable substances, such as
petrol, toner and toner for printers. Prohibit the use of products in clean areas with
ammable items.
· It is forbidden for the product to absorb any burning articles, such as cigarettes,
matches, ashes and other articles that may cause re.
· It is forbidden to place objects at the suction opening. Do not use the product when
the suction port is blocked. Clean all possible blockage at the suction opening to
ensure smooth air circulation at the suction opening.
· Use the power cord carefully to avoid damage. It’s forbidden to use the power cord
to drag or pull the product and the product charging station. It’s forbidden to use the
power cord as a handle. It’s forbidden to clamp the power cord in the crack of the
door. It is forbidden to pull the power cord at sharp corners.
· Do not use a damaged charging/auto station.
· Even if the product has been severely damaged, burning of the product is
prohibited, which may lead to explosion of the battery of the product.
GENERAL SAFETY REGULATIONS:
Before using this product, please read the following safety instructions and follow all routine safety precautions.
Please read the instructions carefully, please keep the instructions.
Any operation inconsistentcy with this instruction manual may cause damage to this product.

4
NOTE:
· Only authorized technicians can disassemble this product. Users are not
recommended to disassemble this product by themselves.
· This product can only use the power adapter provided by the factory. lf other
adapters are used, the product may be damaged.
· Do not touch wires, sockets or power adapters when your hands are wet.
· Make sure no fabrics or bigger items roll into the product drive wheels.
· Do not place this product near cigarette butts, lighters and other smoldering fires.
· Please clean the product after charging.
· Do not bend wires excessively or place heavy objects and sharp objects on the machine.
· This product is an indoor household product. Do not use it outdoors.
· Do not sit on the product.
· Do not use this product (e.g. bathroom) in a wet environment.
· Before using this product, please remove all vulnerable items (e.g. glasses, lamps,
etc.) on the ground as well as items (e.g. wires, paper sheets, curtains) that may
entangle the side brushes and air suction passages.
· Do not put this product in a place where it is easy to fall (e.g. on desks and chairs, by
the stair case).
· Please carefully check whether the power adapter is connected to the socket before
use, otherwise the battery may be damaged.
·To prevent tripping, please inform other members of the house when this product works.
· Please empty the dust bin before using this product when the dust bin is full.
· Please remove the battery from the machine before the product is scrapped.
· Please make sure that this product is not powered on when removing the battery.
· Please recycle the discarded batteries safely.
· Recommended to block the staircase exit or areas where the robot may fall.The anti-
drop sensors prevent the robot from tumbling down stars and steep drops. However,
they may work less effectively when dirty or used on reflective/very dark-colored floors.
· To clean and maintain the robot and the auto station, you must turn off both. Pull
out the power cord from the socket and disconnect the power supply first.
· Do not immerse the robot or the auto station in water for cleaning or rinse them with water.
· Do not whipe any part of the product with a damp cloth or any liquid.
· Do not use the mopping module on the carpet.
SAFETY REGULATIONS

5
EN
2. PRODUCT INFORMATION
PRECISION PLUS robot Auto station Power cord
Instruction manualDust bag 3L (2x)
Side Brush (2x)
Cleaning brush
with knife
Mopping cloth (2x)Mopping Pad 2 in 1 electrically-
controlled water tank
HEPA lter +
Sponge lter (2x)
V shape rolling brush

6
PRODUCT INFORMATION
Filter cover
TOP & FRONT BOTTOM
Anti-drop sensor
Side brush
Roller brush cover
Roller brush cover
Driving wheel
Battery cover
Universal wheel
Dustbin button
Anti-collision sensor
LDS radar
CLEANING ON &OFF
• Short press to start clean/pause
• Long press for 3secs for on/o
CHARGING
• Short press charge/pause
• Long press to start network connection.
(Reset WiFi)
INDICATOR LIGHT
• Blue/White: normal operation or charging
• Red: abnormal condition
• Purple: recharging (back to charge) or low battery
• Blue o: robot is not connected to the network
RESET WIFI
• Long press to start network connection
Recharging
aligning sensor

7
EN
AUTOSTATION / WATERTANK / DUSTBIN AND MOP ASSEMBLY
Dust bag
Dust cover
Signal indicator
Charging pins
Power Socket
Wire storage
Dust collection inlet
Water Inlet
Watertank
Mopping pad button
Mopping pad
Mop
3. INSTALLATION INSTRUCTIONS ROBOT & AUTOSTATION
Primary lter
Sponge
HEPA Filter
Dust bin intake ap
Charging pin

8
AUTO STATION
1 Lay the auto station on the at ground over 5cm away from the wall, insert
the power plug into the socket, meeting the requirements, and connect the
power supply.
2 Ensure that there are no obstacles within 1.5m in front of the auto station
and 0.5m on both sides.
3 The recharging indicator light ashes during charging and it’s steady on
when charging nished. The charging time is about 3 hours.
INSTALLATION INSTRUCTIONS ROBOT & AUTOSTATION

9
EN
PRODUCT ASSEMBLY
1 Install the brush. They are installed when you hear a“click”
sound.
2 Place the 2-in-1 combi watertank in the robot.
3 Fully charge the robot (before 1st time use)
4 Connect with Bluebot app (optional)
5 Start cleaning
NOTE
• Please do not move the auto station without reason and keep it
out of direct sunlight.
• If the auto station is relocated, the robot may fail in positioning
and lose the map. When restarted, the robot will rebuild and
memorise the map. In the rebuilt map the cleaning information for
forbidden areas and other areas may have been lost.
• Direct sunlight will interfere with the recharging signal and
consequently, the robot may be unable to return to the charging/
auto station.
• The robot cannot be used to remove liquids.
• If the battery level is less than 20% the machine will not work.
Please charge it.
• The machine will return to the auto station automatically if the
battery level is less than 20% when in use and will be powered
oand then start cleaning automatically after the battery level
reaches 80%.
• Please clear various wires (including the power line of the auto
station ) from the ground before use to avoid outage and damage
of objects or wires when wires are dragged by the robot.
INSTALLATION INSTRUCTIONS ROBOT & AUTOSTATION

10
INSTALLATION INSTRUCTIONS ROBOT & AUTOSTATION
INSTALLATION OF MOPPING MODULE
1 Paste the mopping cloth at onto the bottom of the water
tank.
2 Fill the water tank: uncap the cover and ll with water.
3 Press and hold the button in the middle of the tank and
push it horizontally along the rear of the robot. The module is
correctly in place correctly if you hear the sound of a“click".
4 Remove the mopping module
When the robot is nished working, press the button in
the middle of water tank to remove the mopping module
backwards, empty the water in the water tank and clean the
mopping cloth (do not move or turn the robot over during
cleaning).
NOTES FOR MOPPING MODULE
· Please do not use the mopping module after it has been left unused.
· For safety reasons, please be sure to remove the mopping module when it is being
charged or left unused.
· Please do not mop the carpet. Set a forbidden area in the Bluebot app to prevent the
machine from going onto the carpet.
· To achieve a better mopping eect, the mopping module should be installed after
take out and reassemble the mopping module according to step 3. Please do not
move or turn the robot over, otherwise, it could fail in its positioning, lose its map and
“forget”the forbidden areas that are programmed.
· The mopping function of the machine is intended for wiping and is not conducive
to deep cleaning. It cannot remove stubborn stains eectively and replace the
labour force.
· Please don't use any detergent in the watertank to prevent clogging.
· The robot cannot be used to remove liquids.

11
EN
BLUEBOT APPLICATION 1 Fully charge robot 2 Download Bluebot app 3 Steps for registration 4 Connect robot with app (steps)
4. INSTALLATION BLUEBOT APP
BLUEBOT APPLICATION 1 Fully charge robot 2 Download Bluebot app 3 Steps for registration 4 Connect robot with app (steps)
Place the robot in the charging station to charge and
make sure it’s fully charged before use. Remove the robot from the charging station.
Make sure the Robot is on, by holding in the ‘On button’
for a few seconds on top of the robot. Wait until the robot
has started fully.
Register a new account if
you are not yet an existing
user.
Open the Bluebot app and
press the ‘+ icon’ to add your
device.
1 2 3
4 5 6
Download the Bluebot app. The app can be found in the
Appstore and Google Play.

12
INSTALLATION BLUEBOT APP
enter the password and
Press on the 'Go to
connect' button in the
bottom of your screen.
Select the 'SmartLife
xxx' network from the
list and return to the
Bluebot app.
Your robot will now
connect to the App.
7 8
9
11 12
Select the
BLUEBOT PRECISION PLUS
After your registration, make sure the robot is removed
from it's charging station. Turn on your robot by pressing
the "On button". After that is done, long press the
recharge button for more than 3 seconds until Wi-Fi
indicator starts ashing.
10
Tick "Conrm indicator blinks
slowly" when applicable and
press ‘Next’.

13
EN
5. USAGE OF THE ROBOT & AUTO STATION
REMOVE THE LIMIT BAR
Put the robot on the flat indoor ground, and remove the protection device
of the limit bar at both ends of the front bumper.
CHARGING OF THE ROBOT
Press and hold the button for 3 seconds to start the robot, and then
short-press the button to make the robot recharge automatically. The
robot is ready once fully charged.
• Fully charge the robot before starting cleaning.
• Before starting the cleaning, tidy away the wires and articles on the
ground to avoid damage caused by winding, dragging and hitting during
cleaning.
• It is suggested to start the robot at the auto station.
• When the battery is low during the cleaning, the robot will automatically
return to the auto station for charging, and automatically return to the
interrupted place to continue cleaning when the battery is full.

14
USAGE OF THE ROBOT & AUTO STATION
CLEANING MODE
After the robot is powered on, it will scan and generate the map and divide
it into areas intelligently. Then sweep the areas one by one along the wall
orderly, efficiently and thoroughly and plan the cleaning route in a bow/S
shape. The robot will return to the charging station automatically after
cleaning.
NOTE
Do not move the robot casually and frequently when it is cleaning. After
moving, please put the robot near the original position. When it starts
again, it will try to reposition itself. After successful positioning, it would
follow the planned path and continue to work. If the positioning fails, the
robot would abort previous mission, make a map and do the cleaning
again.
SPOT CLEANING
When a local area needs a deep sweep, the user specifies a point on the
map on the APP, the machine will automatically drive to the vicinity of the
point, take the point as the center, and clean within 1.5m x 1.5m.
PARTIAL CLEANING
When the robot cannot be controlled by the mobile APP, please remove
the robot to the place you want to clean. Long press the button for 3
seconds, and the robot will clean twice within the scope of 2mx2m
centering on itself.
Area being cleaned
Area to be cleaned
2m
2m

15
EN
SET A RESTRICTED ZONE/ INVISIBLE WALL
You can set a restricted zone or invisible wall in the app. After the setting
is completed, the robot will not enter the restricted zone or cross the
invisible wall for cleaning.
NOTE
Before using this function, you need to open the map save mode in APP setting.
This function is only used to divide cleaning zones, but cannot be used to block
dangerous zones.
If the vacuum cleaner is moved or there are big changes in the home, the map
may become invalid and the settings of the invisible wall or restricted zone
may be lost.
CLEAN SELECTED ZONES
You can select cleaning zones in the app. The robot will clean one or more
rooms based on the zones that you select on the app map, and you can set
room cleaning times in the current mode.
NOTE
Before using this function, you need to open the map save mode in APP setting
and the robot has to generate a map for cleaning.
After cleaning starts, the robot may move to a place beyond the selected zone.
Make sure that you have cleared the obstacles on the ground around the
selected zone, which cannot be used for safety isolation.
USAGE OF THE ROBOT & AUTO STATION
visual wall
cleaning
restricted zone
mopping
restricted zone

16
MORE OPTIONS
Timer*
Set a timer to program the robot to clean at a certain time or day.
Manual
Control the robot manually with the remote control or use the Bluebot app
on your phone as a remote control.
Find robot
Tap this button when you lost your robot and your robot will tell you where
it is.
Map management*
Use this function to manage your maps (5 max.).
Water regulation
Control the water regulation and choose“Low”,“Medium”or“High”. This will
regulate how wet the mop will become when using the robot including
the 2 in 1 electric- controlled water tank.
Auto Boost*
Auto Boost will increase suction power when the robot gets more friction.
This is designed to increase suction on carpets.
Custom mode*
So the robot can remember per area what route to use for cleaning.
Record*
View all your previous vacuum cleaning records. You can see how many m2
has been cleaned and the time it took. Here you can also load previously
saved maps. Ideal when cleaning different area’s (upper floor for instance).
Voice and volume
Setup your language and change the volume.
Do not disturb mode
Here you can schedule an do not disturb time period.
Consumables and Maintenance*
Here you will find an overview of consumables and indicates when
consumables need to be replaced or Entretien is required.
More info*
Here you will find network and robot information
Set wall / Resctricted Area*
Use this function to create no-go zones within the area that you are
cleaning. You can draw virtual walls that blocks the robot from crossing. Or
you create a restricted area for either vacuuming or mopping.
* Via Bluebot app only
6. CLEANING SETTINGS

17
EN
REPLACE THE DUST BAG
When the dust bag is full, please replace the dust bag in time.
7. MAINTENANCE
Open the
upper cover
Close the
upper cover
Make sure that the
dustbag is installed
in place
Place a new dust bag
Pull up the lifting
handle of the dust
bag and take out
the dust bag
4

18
CLEAN THE INFRARED LENS/CHARGING AND DUST
COLLECTION SENSOR HEAD
Wipe them gently with a clean, soft, dry cloth. It is recommended to clean
them once a month.
CLEAN THE FILTER SCREEN OF THE FAN
The lter screen of the fan is below the dust bag. If there is dust
accumulation, wipe it gently with a clean, soft, dry cloth.
It is recommended to clean them once a month.
MAINTENANCE
Fan lter screen

19
EN
MAINTENANCE
ROLLING BRUSH | REGULAR CLEANING
1 Turn over the machine and press the buckle on the rolling brush
cover to take out the rolling brush. Filter cover cleaning
2 Remove dust outside and inside the rolling brush using a tiny brush and
clean the rolling brush.
3 Reassemble the rolling brush and press the rolling brush and the rolling
brush cover tightly to completely close it again.
SIDE BRUSH | REGULAR CLEANING
1 Turn over the machine and pull the side brush out and upwards
2 Remove hair and dirt and reassemble the side brush.

20
MAINTENANCE
2 IN 1 ELECTRICALLYCONTROLLED WATER TANK
| REGULAR CLEANING
1 Press the button and pull the dustbin out backwards.
2 Open, empty and clean the dustbin.
FILTER | REGULAR CLEANING
1 Remove the primary lter, sponge and HEPA.
2 Clean the removed primary lter, sponge, and Dust bin HEPA with water
if needed.
3 Shake othe water drops and dry the pieces naturally, then use them
after they have completely dried.
4 When dry, install them in the sequence: HEPA > sponge > primary lter.
Primary lter
Sponge
HEPA
Water tank