blossom-ic AVALON+ User manual

AVALON+
Assembly instructions
1.0
Version
Wireless radiator thermostat for direct connection to the thermostatic
valve M 30 x 1.5mm, for controlling the radiators. With patented procedure
for independent and self-learning dynamic hydraulic balancing of single
and two-pipe heating systems. In combination with Gateway GT-100.
Up to 20 Avalon+ thermostats can be connected to one Gateway.
Brief description:
intelligent | economic | cost-saving | individual | flexible | user-friendly | smart | profitable | innovative

ADR | Oberer Buxheimer Weg 60, D-87700 Memmingen P| [phone] E| [email protected]
blossom-ic GmbH & Co. KG |Intelligent Controls
2
Contents...
Connection of the Gateway GT-100 ............3
Registration of Avalon+...........................3
Download the blossomic app ....................5
Technical data......................................6
Settings & key functions .........................6
• Explanation of the heating programs........ 7
• Settings via the thermostat ................. 7
• Window opening detection ................... 7
• Reset to factory settings.....................8
• Further information ...........................8
Safety Instructions ...............................8
Mounting on the valve ............................8
Declaration of conformity ........................8
Warning notice ....................................9
Appropriate use ...................................9

Assembly instructions: Avalon+
3
Connection of the Gateway GT-100
Screw on antenna Connect power supply unit Connect the network cable
Both diodes are permanently lit:
Gateway active
Check status
Green diode lights up constantly: Internet
connection is establishing.
Green diode lights up constantly: Internet
connection is successfully established
Registration of Avalon+
Inserting batteries „REG“ appears in the display Press the register key on the
gateway for 3 seconds.
1. 2. 3.
4. 5.
1. 2. 3.
Hint:
Functionality in the home safe area. Internet
connection is used for convenient setting
and control via smartphone.
The system functionality is guaranteed even
if no Internet connection is available.

ADR | Oberer Buxheimer Weg 60, D-87700 Memmingen P| [phone] E| [email protected]
blossom-ic GmbH & Co. KG |Intelligent Controls
4
Thermostat displays the current
ID
Press any button on the Avalon+
thermostat within 30 seconds
Press any key on the Avalon+
The thermostat shows the
current room temperature the
registration was successful
Mount Avalon+ on the valve and
tighten. Please note: Sensor
should not be covered.
4. 5. 6.
7.

Assembly instructions: Avalon+
5
Download the blossomic App
The blossomic app is available for both iOS and Android. You can find the app by entering „blossomic“
in the App or Google PlayStore. Alternatively, you can scan the QR code below with your smart-
phone. This leads you directly to the download page of the blossomic app.
Setting up the blossomic app
For initial registration, use the MAC address of the gateway (12 dig-
its, attached at the back). The MAC address serves as user name and
password.
Aer successful login, you will be asked to provide individual access
data.
As soon as you have assigned these data, all heating programs and
other parameters can be set easily and conveniently via the app.
Important notice:
In order to be able to guarantee smooth functionality of all thermostats and devices as a unit, all components (including the devices that are
added later) as described on page 5 below (“Registering the radiator thermostat” - steps 2 to 3), are registered via the gateway.
Automatic IP address recognition and automatic Voice recognition.
There is no need to set daylight savings time, daylight savings time
or date and time.
Username
Password
Login
Remember me Show password
Forgot password?
User data
New username
E-Mail address
Gateway Mac: 00059EF40735
Submit
Set new passwort
Confirm new passwort
I agree to my details to answer my request
collected and processed.
on handling user data in our .
I have read and understood the of blossom-ic
GmbH & Co. KG and agree to it.

ADR | Oberer Buxheimer Weg 60, D-87700 Memmingen P| [phone] E| [email protected]
blossom-ic GmbH & Co. KG |Intelligent Controls
6
Technical data
Ambient temperature
Operating voltage
Mains voltage
Dimension
Wireless frequency
Protection class
RF Test
CE
RoHs
Type of antenna
Technical data - Gateway GT-100 black
0 ~ 50°C
DC 12V 1A
230 V AC / 50/60Hz
L113 x W73 x H35 (mm)
2.4GHz, ISM Band, 16 channels
IP 30
RED 2014/53/EU
Available
Available
Monopole 2.4 GHz
Settings & key functions
Radiator-radiator thermostat, blossomic radio and app technology.
To activate the parental lock: Press the „Comfort“ and „Up Arrow“ button for 5 seconds. (A lock appears on the screen)
To deactivate the parental lock: Press „Comfort“ and „Up arrow key“ for 5 seconds.
Technical data - Avalon+ thermostat
Setpoint range
Ambient temperature
Ambient humidity
Battery intake
Dimension
Connector
Wireless frequency
Protection class
RF Test
CE
RoHs
6 ~ 30°C
0 ~ 50°C
85% (non-condensing)
2x Mignon AA 1.5V, battery
L110 x Ø 58 mm
M 30 x 1,5 mm
2.4GHz, ISM Band, 16 channels
IP 30
RED 2014/53/EU
Available
Available
Radio signal
Arrow key +
Valve connection: M30 x 1.5mm
Arrow key -
Set-Temperature
Motion sensor
current heating
program
Press for 3 seconds to
change to the night set-
back heating program
Heating program Eco/Absent
Heating program Comfort
Motion sensor active
Internet connection

Assembly instructions: Avalon+
7
Settings via the thermostat
At wake-up time (e.g. 7:00 a.m.) the radiator starts heating from 7:00 a.m. The thermostat automatically switches to Comfort mode. (The set-
tings on the thermostat are optional. With the app all settings of the heating programs and temperatures can be made easily and conveniently)
Please note The Avalon+ thermostats only control the individual rooms (temperature and times). Please note which times the boiler is set to.
With the Comfort programme you control your comfort temperature
(set to 22° at the factory). The desired temperature and programme
times can be conveniently set using the thermostat and app. If the
sensor is activated and no one is present within 30 minutes, the sys-
tem lowers the temperature by 2° and switches to eco mode or night-
time reduction (depending on the time of day) aer a further 30 min-
utes without anyone being present. If the sensor detects movement,
the program immediately switches to Comfort mode. If the sensor
is deactivated (only possible via the app), the temperature remains
constant until the next switching phase (eco or night-time reduction).
Detailed instructions can also be found in the app description.
Heating program Comfort
With the Eco program you can set the desired temperature for longer
periods of absence (set to 12° in the factory). The desired tempera-
ture and program times can be conveniently set using the thermo-
stat and the app. By pressing the Eco button on the thermostat, you
can switch directly from Comfort mode to Eco mode. To do this, the
motion sensor is deactivated for 10 minutes. If the sensor detects
movement aer 10 minutes, the program switches back to Comfort
mode. If the sensor is deactivated (only possible via the app), the
temperature remains constant until the next switching phase (Com-
fort or night setback). Detailed instructions can also be found in the
app description.
Heating program Eco
Declaration of heating programs
This program lowers the temperature at night to save energy (set to
16° at the factory). You can easily set the desired temperature and
program time using the thermostat and the app. The motion sensor
is deactivated during the night setback. By pressing the night set-
back button on the thermostat, you can switch directly from Comfort
mode to night setback. When the sensor is deactivated (only possible
via the app), the temperature remains constant until the next switch-
ing phase (Eco or Comfort). Detailed instructions can also be found
in the app description.
Heating program Night Setback
By pressing the night setback button on the thermostat twice, you
can set the time at which morning comfort is to be activated. Set the
desired time and confirm the setting by pressing the night setback
button again. All settings of the heating programs and temperatures
can be made easily and conveniently with the app. Detailed instruc-
tions can also be found in the app description.
Heating Time Setting
In the first heat-up phases aer commissioning, the valves are au-
tomatically adjusted and set by the Avalon+ System. This process is
repeated several times as required. This process allows the system to
adapt to the individual conditions in the premises.
Adjustment phase Avalon+ System
Window opening detection
The window opening detection in blossom-ic is activated by a temperature drop of 2°C in 5 minutes and puts the thermostat in frost protection
mode (6°C). As soon as this function is activated, „OPEN“ appears on the display. If the window is closed within 30 minutes and the tempera-
ture in the room rises again, the thermostat automatically returns to the last activated mode.
If the window is open for more than 30 minutes or the temperature does not rise, the thermostat remains in frost protection mode and must
be manually reactivated on the thermostat.

ADR | Oberer Buxheimer Weg 60, D-87700 Memmingen P| [phone] E| [email protected]
blossom-ic GmbH & Co. KG |Intelligent Controls
8
Attention! Important note:
Installation and assembly of electrical devices may only be carried out by a qualified electrician. Non-observance of the assembly and instal-
lation instructions may result in fire or other hazards.
Safety Instructions
The Avalon+ fits valves with an M 30 x 1.5mm connection. Suitable makes: Heimeier, Junkers, Landys & Gyr, MNG, Honeywell 30 x 1.5, Herz 30
x 1.5 and Oventrop 30 x 1.5..
Adapter:
To mount the Avalon+ on Danfoss valves you need an adapter (e.g. from Heimeier):
Heimeier 9700-24.700 (Adapter for Danfoss RAV/L valves)
Heimeier 9702-24.700 (Adapter for Danfoss RA valves)
Heimeier 9800-24.700 (Adapter for Danfoss RAV valves)
For niches we recommend our product Avalon Combo+.
For all other valves, please use the dierent adapters of the respective manufacturers. These are available from specialist dealers on request.
We recommend metal adapters for exact functionality!
Mounting on the valve
Further information
Hint:
When the batteries are empty and the ther-
mostat switches o, the heating in the last
activated mode, to switch the Freezing of the
heating and the unwanted to prevent cool-
ing of the rooms is the Frost protection (6°C)
activated.
What is to be done?
To restore normal operation please change
the batteries immediately. The system has
a memory function that automatically re-
stores the last set heating program.
Valve protection function:
The system opens and closes the valves once
a week automatically, so that ensures that
the valves do not/or block it.
Hereby blossom-ic GmbH & Co. KG hereby declares that the following product: Avalon+ AP-3977 is in compliance with the essential require-
ments and other relevant provisions of Directive 2014/53/EU. The complete declaration of conformity can be found at the following address:
www.blossomic.de/downloads Declaration of conformity
Declaration of conformity
Reset thermostat to factory setting
Press comfort button until “bin” appears in the display -> press comfort button until “Set” ID appears. -> Select ID 0 and confirm with “Com-
fort-Key”

Assembly instructions: Avalon+
9
The thermostat is not suitable for children and must not be used as a toy. Store and dispose of packaging materials in a child-resistant manner.
Do not disassemble the thermostat, as it does not contain any user-serviceable parts. If the error code E1, E2, etc. is shown on the display or
other defects occur, please return the thermostat to the dealer.
This appliance may be used by children over 8 years of age and by persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge, provided they have been supervised or instructed in the safe use of the appliance and understand the hazards
involved. Children must not play with the device. Cleaning and user maintenance must not be performed by children without supervision.
Warning notice
The Avalon+ is only suitable for controlling radiators, convectors or heating bars heated by heat transfer media. The regulation of e.g. cooling
circuits, underfloor heating, etc. is not permitted and may lead to damage.
Appropriate use

blossom-ic GmbH & Co. KG
Oberer Buxheimer Weg 60, 87700 Memmingen, Germany
P: [phone] E: [email protected]
W: www.blossomic.de