Honeywell INNCOM e7w User manual

1 31-00308–01
e7w Wireless EMS Thermostat
INSTALLATION INSTRUCTIONS
FOR ALL UNITS IN CARTON. DO NOT THROW AWAY!
INSTALLATION REQUIREMENTS
Required Installation Hardware
•Four 6-32 × 1.5” Philips Pan head screws (provided with e7w) if attaching to a 4X4 electrical junction
box.
•Four AA alkaline batteries; provided with e7w.
•e7w Smart Wall Mounting Plate; provided with e7w.
•Three 4-24 1/2’’ Phillips screws Phillips captive screws; provided with e7w.
•Phillips Screwdriver.
•Wire cutters/strippers.
Required Commissioning Tools
DO NOT THROW THIS UNIT AWAY: One PC-503 USB Commissioning Tool and USB cable per property/project
is shipped to the site.
This tool is used in conjunction with Honeywell's engINN commissioning software when advanced commis-
sioning of the e7w is required by a trained and certified INNCOM technician. Contact Honeywell technical sup-
port for more information.
Figure 1: PC-503 USB commissioning tool and cable

e7w WIRELESS EMS THERMOSTAT - INSTALLATION INSTRUCTIONS
31-00308–01 2
CAUTION
•Read instructions carefully. Failure to follow
them could damage the product or create a
hazard.
•Check the ratings given in the instructions
and on the product to ensure that the prod-
uct is suitable for your application.
•Installer must be a trained, experienced ser-
vice technician.
•After installation is complete, check product
operation as indicated in instructions.
•For variations of these systems, refer to the
installation instructions of the controlled
equipment.
INSTALLATION
Location
Select a location about 1.5m (5ft.) above the floor
with good air circulation at average temperature.
Do not mount thermostat where it may be af-
fected by:
•Drafts or dead spots behind doors or in cor-
ners.
•Hot or cold air from ducts.
•Radiant heat from sun or appliances.
•Concealed pipes or chimneys.
•Unheated (un-cooled) areas behind the ther-
mostat.
•Near other RF sources/ transmitters to avoid
interference.
•When the thermostat is equipped with PIR,
consider view angle, range characteristics,
and mounting position for proper coverage.
Figure 2. Recommended mounting location
Mounting
The e7w Wireless EMS thermostat supports
mounting on the following standard mounting
junction boxes; US single-gang, US double-gang
and UK standard gang. The installation kit pro-
vides a Smart Wall Mounting Plate.
If mounted on a single-gang box, the right side
(keypad side) of the e7w overlaps the wall area to
the right.
To mount the e7w, follow the below steps:
1. Take the Smart Mounting Plate and orient it
with the raised arrow embossed on mounting
plate pointing UP.
2. Attach the plate to the junction box using the
supplied screws as shown in Figure 3.
3. Insert the 4 AA alkaline batteries.
Note:
•Use alkaline batteries only.
•Refer the “Battery details” sections for
more information.
4. After inserting AA batteries, all segments and
characters of the LCD are illuminated for
couple of seconds. Confirm all segments and
characters on the e7w LCD are displayed
correctly.
Refer LCD Display section for more details.
5. If the LCD displays blank information, run
the following checks:

e7w WIRELESS EMS THERMOSTAT - INSTALLATION INSTRUCTIONS
331-00308–01
a. Verify that the batteries installed in cor-
rect terminal.
b. Check the battery voltage.
6. Hook the tabs at the top rear of the e7w
housing into the matching depressions at
the top of the Smart Mounting Plate and ro-
tate the bottom of the housing toward the
wall until it snaps into place.
7. After startup, the e7w will cycle through RF
Channels 26, 25, 24… all the way to 11 and
send a 0x00061 Battery Powered thermostat
exchange message on each RF Channel
looking for a reply from an HVAC thermostat
partner with the same Room ID currently
stored in the e7w. Allow this process to con-
tinue until completion. Later you need to
configure the actual Room ID and other re-
quired parameters into the e7w.
8. Secure the housing to the Smart Mounting
Plate with the two small captive screws at the
bottom of the housing.
9. After you configured Room ID and other re-
quired parameters, restart the device and
wait for 5 seconds LCD will display all config-
ured values and various mods.
Figure 3. e7w exploded assembly reference
Battery Details
Figure 4. e7w Battery polarity reference
1. Battery Compartment: Holds 4 AA Alka-
line Batteries.
2. Insert the 4 AA alkaline batteries, match-
ing the “+” terminals on the batteries to
the “+” symbols in the battery compart-
ment, as shown in Fig. 4.
CAUTION
Risk of explosion if battery is replaced by an in-
correct type.
Dispose the used batteries as per instructions
under WEEE Directive 2012/19/EC.

e7w WIRELESS EMS THERMOSTAT - INSTALLATION INSTRUCTIONS
31-00308-01 4
Specifications
Mounting
Standard US Double Gang: w/o Spacer Ring
Standard US Single Gang: w/o Spacer Ring
Standard UK Single Gang: w/o Spacer Ring
Dimension
L 120mm x W 120mm x H (23) mm (w/o spacer)
Ambient Operating
41 to 149 °F (5 to 40 °C), 0-95% RH non-condensing
Ambient Storage
33 to 149 °F (1 to 65 °C)
C/F degrees display
Toggle Button located on front display.
In room Temperature
60°F to 85°F (± 1°F) [15°C to 30°C (± 0.5°C)]
Power
6VDC Alkaline Batteries.
Color Variants
Ice White & Black Onyx
Display resolution
HTN LCD, 0.5 °C (0.1 °F in test mode).
Standard dead band
2 °F (1 °C) between heating and cooling.
Thermostat Measurement range
33 to 99 °F (1 to 37 °C) +/- 1.8 °F.
Outdoor air temperature display
Temp 0 to 99 °F (-18 to 37 °C) as reported from web service
Motion sensor
120° View Angle, 10meter line of sight
Light Sensor
Gamma Value 0.7, Spectral response 550 –650nm.
Humidistat
3 % RH, in range from30-95 % RH +/- 5%.
Frequency range
2405MHz to 2480MHz
Maximum power
5dBm
Hardware version
A
Firmware version
1.1.0

e7w WIRELESS EMS THERMOSTAT - INSTALLATION INSTRUCTIONS
531-00308–01
Wireless Communications
Parameter
Description
RF Data Rate
250kbps
Antenna Type
SMT
Indoor range
70ft
Transmit Power
+5dBm
Receive Sensitivity
-95dBm
Frequency Band
2.4Ghz
Encryption
AES -128
Protocol
802.15.4
Frequency Channels
11-26
Note:
•Required Deep Mesh Network 2.4GHz.
LCD Display
Figure 5. e7w LCD display segments
1
Target (SET) temperature value
2
Temperature units
3
Door or Lanai
4
Measured temperature icon
5
Fan Speed (Low, Medium, High)
6
Auto Fan speed
7
Measured temperature value
8
Outside temperature icon
9
Heat only mode
10
Cool only mode
11
Eco mode
12
Equipment alarm
13
Low battery alarm

e7w WIRELESS EMS THERMOSTAT - INSTALLATION INSTRUCTIONS
31-00308-01 6
INITIAL SETUP
Before going through the initial setup se-
quences, ensure the thermostat is mounted and
connected to the Smart Wall.
Note:
−When properly connected, the thermo-
stat will proceed into INTIALIZATION
MODE and display rId.
−When not properly connected to the
Smart Wall Plate, the unit will display
the alert message SWp and the alert
icon will illuminate until the Smart Wall
Plate is connected.
If you see SWp on the display, most likely the
unit is not connected or properly seated on the
Smart Wall Plate. Unscrew the captive screws
and re-seat the thermostat. Once properly
connected, the display will start up as noted.
Take care not to over-tighten the screws and
note any irregularity on the wall surface that
may lead to an insecure connection between
the Smart Wall Plate and thermostat.
Setup Room ID
Figure 6. Setup Room ID
1. Once rld is displayed, press MODE. The de-
fault Room ID value (65535) is displayed and
will begin scrolling across the screen one nu-
merical setting at a time, from highest to low-
est (left most to right most value).
Note:
The five-digit number is comprised of three
fields: highest digit, middle two digits, low-
est two digits (HIMEDLO), default value
(65535). Three settings must be made.
2. In HI (high) value page, use the UP/DOWN
arrow buttons to change this value (range is
0-6). Press FAN to continue.
3. Set the MED (medium) values in the se-
quence using the UP/DOWN arrow buttons
(range is 0-99). Press FAN to continue.
4. Repeat the same step for the LO (low) two
values (range is 0-99) and press FAN to con-
tinue. Press MODE to accept the value.
5. The new ID number scrolls across the dis-
play. The unit beeps to confirm the value is
stored to memory. Once the scrolling is com-
pleted, screen will return to INTIALIZATION
MODE.
6. If you want to continue, press the DOWN ar-
row button to display rF mode (RF channel
for IRAS communication).
Or
If you want to exit the INTIALIZATION MODE,
press the FCkey.
After you configured ROOM ID, you need to
configure RF channel for IRAS communica-
tion.
Figure 7. Configuring Room ID

e7w WIRELESS EMS THERMOSTAT - INSTALLATION INSTRUCTIONS
731-00308–01
Setup RF Channel
Figure 8. Setup RF Channel
1. After rF is displayed, press MODE.
2. Default rF value 26 displayed on the screen.
3. Use the UP/DOWN arrows to change value
range between 11 to 26.
4. Press FAN, the unit beeps to confirm the
value stored in the memory and display will
be back rF.
5. Press MODE to check the value.
6. Once the rF configured, Press FCto re-
turn INTIALIZATION MODE.
7. If you want to continue, press the DOWN ar-
row button to display PAn mode
Or
If you want to exit the INTIALIZATION MODE,
press the FCkey.
After you configured RF channel, you need to
configure PAN channel for IRAS communica-
tion.
Figure 9. Configuring RF channel
Setup PAn ID
Figure 10. Setup PAn ID
After PAn is displayed, press MODE.
1. Default PAn value is 0 displayed on the
screen.
2. Use the UP/DOWN arrows to change value
range between 0 to 255.
3. Press FAN, the unit beeps to confirm the
value stored in the memory, the display will
be back to PAn.
4. Press MODE to check the value.
8. Once the PAn configured, Press FCto re-
turn INTIALIZATION MODE.
9. If you want to continue, press the DOWN ar-
row button to display rld mode
Or
If you want to exit the INTIALIZATION MODE,
press the FCkey.
Service Mode
To configure the HVAC controller, wireless mo-
tion sensors, and doors/windows/balcony
switches with e7w, you need to set e7w into Ser-
vice Mode.
To enter Service, follow the below steps:
1. Press and hold FCkey.
2. Press and release MODE.
3. Press and release FAN.
4. Release FCkey.

e7w WIRELESS EMS THERMOSTAT - INSTALLATION INSTRUCTIONS
31-00308-01 8
BINDING AUXILIARY DEVICES
Note:
Before binding or verifying auxiliary devices.
•e7w must be configured with correct Room
ID, PAN ID, and RF Channel.
•For forward bind method, place the remote
device into a discovery mode that can re-
ceives the request sent from the thermo-
stat and reply to the request.
•For reverse bind method, mount the ther-
mostat in a such location, that can receive
request sent from the remote device and
reply to the request.
Binding PC502.4G
1. Enter SERVICE MODE. use the UP/DOWN
arrow buttons to select Io.
2. Press MODE. The information display
changes to show Io and a value.
3. Use the UP/DOWN arrow buttons to change
the displayed value range from 0 to 255. Set
the Io value to the desired I/O map number.
4. Press FAN to initiate a reverse bind.
5. Press Reset/Bind switch on the PC502.4g
(use a small point like the end of a straight-
ened paper clip).
If the PC502.4G binds successfully, it will
flash Led and send message to make the unit
beep, confirming that the bind was success-
ful.
6. Press FCto exit service mode.
Binding Door/Window/Balcony
Switch
1. Enter SERVICE MODE, use the UP/DOWN
arrow buttons to select Io.
2. Press MODE. The information display
changes to show Io and a value.
3. Use the UP/DOWN arrow buttons to change
the displayed value range from 0 to 255. Set
the Io value to the desired I/O map number.
4. Press FAN to initiate a reverse bind or press
MODE to initiate a forward bind.
5. Press the S1 switch on the device to initiate
binding process.
If the device binds successfully, it will flash
Led and send message to make the unit
beep, confirming that the bind was success-
ful.
6. Press FCto exit service mode.
Figure 11: Configuring IO mode
VERIFYING AUXILIARY DEVICES
1. Enter SERVICE MODE, use the UP/DOWN
arrow buttons to select PnG.
2. Press MODE. The information display
changes to show PNG and a value.
3. Use the UP/DOWN arrow buttons to the ad-
dress of the target device to be pinged.
4. Press FAN to initiate pinging the target de-
vice. After few seconds, it will start communi-
cating the reply and values will be displayed.
5. Press the FCbutton to stop pinging.
6. Press FCto exit service mode.

e7w WIRELESS EMS THERMOSTAT - INSTALLATION INSTRUCTIONS
931-00308–01
STANDARDS AND APPROVALS
EN
•Product Standard −EN 60730-1:2011 and
EN 60730-2-9:2010 (covers EMC and LVD
Safety requirements).
•EMC Standard −ETSI 301489-1 V2.2.1, ETSI
301 489-17 V 3.2.0.
•EMC Standard EN 55032 −Radiated RF
Emissions.
UL (IEC)
•UL 60730-1, 5th edition and UL 60730-2-9,
4th edition.
•IEC and EN EMC standards:
oEU RoHs: EN 50581:2012 per EU RoHS
Directive 2011/65/EU,
oEN 50581:2012 per EU RoHS Directive
2011/65/EU.
oIEC60417, No.5957. For indoor use only.
oClass III equipment per IEC 61140.
•Radio –FCC Part 15 Subpart C (15.249), In-
dustry Canada RSS-210 Issue 9:2016 and
RSS-GEN Issue 4:2014.
•IPx1 protection.
•Pollution Degree 2.
•Type 1 action, operating control.
CSA
•CSA (IEC Based), Note 1 on standards,
Note 2 on aspects impacted by transition
•CAN/CSA E60730-1, 5th edition
•CAN/CSA E60730-2-9, 4th edition
Note 1
We have a choice of the IEC based path or
the updated version of Spec. 24. Considera-
tions:
•CSA C22.2 No. 24-93 has been in place
but will not be allowed from Jan. 1, 2017.
It is being replaced with CSA C22.2 No.
24-2015 as of that date (Environmental
Requirements).
•CSA C22.2 No. 24-2015 references CSA
C22.2 No. 0.8 for electronic controls with
safety functions, functional safety and
EMC instead of 60730-1 Annex H.
•According to CSA, the deviations for
Canada added to CAN/CSA 60730-1
and 60730-2-9 make this choice equiv-
alent to use of CSA C22.2 No. 24-2015.
Regulatory Compliance
UL Listing
This device meets UL 60730-2-9, CAN/CSA-
E60730-2-9 Standard for Automatic Electrical
Controls - Part 2-9: Requirements for Tempera-
ture Sensing Control
Federal Communications Commission
(FCC)
Changes or modifications not expressly ap-
proved by the party responsible for compliance
could void the user’s authority to operate the
equipment. This equipment has been tested and
found to comply with the limits for a Class B dig-
ital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a res-
idential installation. This equipment generates,
uses and can radiate radio frequency energy and,
if not installed and used in accordance with the
instructions, may cause harmful interference to
radio communications. However, there is no

e7w WIRELESS EMS THERMOSTAT - INSTALLATION INSTRUCTIONS
31-00308-01 10
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning
the equipment off and on, the user is encouraged
to try to correct the interference by one of the fol-
lowing measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equip-
ment and receiver.
•Connect the equipment into an outlet on a
circuit different from that to which the re-
ceiver is connected.
•Consult the dealer or an experienced ra-
dio/TV technician for help.
This device complies with FCC and IC radiation
exposure limits set forth for an uncontrolled en-
vironment. This device should be installed and
operated with minimum distance of 20cm be-
tween the radiator and your body. This device
must not be co-located or operating in conjunc-
tion with any other antenna or transmitter.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause harm-
ful interference, and (2) this device must accept
any interference received, including interference
that may cause undesired operation.
Tout changement ou modification n’ayant pas
été expressément approuvé par la partie re-
sponsable de la conformité pourrait annuler
l’autorisation de l’utilisateur d’utiliser l’équipe-
ment. Cet équipement a subi des tests prouvant
sa conformité aux limites prescrites pour les ap-
pareils numériques de classe B, selon la partie
15 des règlements de la FCC. Ces limites ont été
conçues pour fournir une protection raison-
nable contre les interférences nuisibles lorsque
l’appareil est utilisé dans un environnement ré-
sidentiel. Cet équipement génère, utilise et peut
émettre de l’énergie radioélectrique et, s’il n’est
pas installé et utilisé conformément aux in-
structions, peut causer des interférences nuisi-
bles aux communications radio. Toutefois, il n’y
a aucune garantie que ces interférences ne
puissent survenir dans une installation par-
ticulier. Si cet équipement cause des interfé-
rences nuisibles à la réception de signaux de ra-
dio ou de télévision, ce qui peut être déterminé
en l’éteignant et en l’allumant, l’utilisateur peut
essayer de corriger ces interférences par les
mesures suivantes :
•Réorienter ou déplacer l’antenne récep-
trice.
•Augmenter la distance entre l’équipe-
ment et le récepteur.
•Brancher l’équipement sur un circuit dif-
férent de celui sur lequel le récepteur est
branché.
•Consulter le détaillant ou un technicien
expérimenté en radio/télévision pour de
l’aide.
Cet équipement est conforme aux limites d’ex-
position aux rayonnements FCC et IC établies
pour un environnement non contrôlé. Cet
équipement doit être installé et utilisé avec un
minimum de 20cm de distance entre la source
de rayonnement et votre corps. Cet appareil ne
doivent pas être placés à côté de ou fonctionner
en conjonction avec toute autre antenne ou
transmetteur.
Industry Canada (IC)
This device complies with Industry Canada li-
cense-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this
device may not cause interference, and (2) this
device must accept any interference, including
interference that may cause undesired operation
of the device.
Le présent appareil est conforme aux CNR d'In-
dustrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée
aux deux conditions
suivantes: (1) l'appareil ne doit pas produire de
brouillage, et (2) l'appareil doit accepter tout
brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le
fonctionnement.

e7w WIRELESS EMS THERMOSTAT - INSTALLATION INSTRUCTIONS
11 31-00308–01
WEEE Directive 2012/19/EC Waste
Electrical and Electronic Equip-
ment Directive
The correct disposal of end-of-life equipment will
help prevent potential negative consequences
for the environment and human health. Dispose
of the packaging and this product in an author-
ized collection or recycling center. Do not dis-
pose of the unit with domestic refuse. Do not in-
cinerate.

e7w WIRELESS EMS THERMOSTAT - INSTALLATION INSTRUCTIONS
The material in this document is for information purposes only. The content and the product described are subject to change without notice.
Honeywell makes no representations or warranties with respect to this document. In no event shall Honeywell be liable for technical or editorial
omissions or mistakes in this document, nor shall it be liable for any damages, direct or incidental, arising out of or related to the use of this
document. No part of this document may be reproduced in any form or by any means without prior written permission from Honeywell.
Honeywell
12 Clintonville Rd, Northford, CT 06472, USA
+1.203.484.7161
For more information: www.inncom.com
© 2019 Honeywell International Inc.
31-00308 | Rev. 01 10-19