BlueRange UNO9BLACK/SP User manual

ZBLUERANGE
USER MANUAL
SOLAR POWERED AUTO DARKENING WELDING HELMET
U:71
mz
Train
yymm
TTY11111.1J
I T =
e• 10 • • •
OOOOO 11110 •
!MT=
MODEL NUMBER:
UNO9BLACK/SP
IMPORTANTNOTICE:
Please read these instructions carefully before using this unit, failure to comply with
them may reduce the performance of the unit risking your safety and invalidate the
guarantee.

Auto -Darkening Filter
Welding Helmet
Auto -darkening welding helmet is designed to protect the
eyes and face from sparks, spatter, and harmful radiation
under normal welding conditions. Auto -darkening filter
automatically changes from light to dark state whenthe arc
is struck, and returns to the light state whenwelding stops.
Auto -darkening welding helmet comes ready to use. The only
thing youneed to do before welding is to adjust the position
of the headband and select the correct shade number for your
application.
There is also a visor for protection onother operations.
BEFORE WELDING
•Checkthe front cover lens to make sure that they are cleanand there is no dirt covering the
four sensors on the front of the filter cartridge and check the front/inside cover lens to make
sure that they are secure.
•Check all operatingparts before use for signs of wear or damage. Any scratched, cracked or
pitted parts should be replaced immediately before using again to avoid severe personal injury.
•Checkfor light tightness beforeeachuse.
Select a shade number by the shade knob (see Shade Guide Table No.1) ensuring that the shade number is
the correct setting for your application. Adjust the headband so that the helmet is seated as low as possible
on the head and close to your face. The angle of the helmet is adjusted using the buckles.
DARK SHADE NUMBER SELECTION
The shades ranges from 9-13. The shade section is selected by switch K4. When used for grinding, you can
set the Grind/Weld switch (1<5) to "GRIND". Refer to the shade guide table to determine the proper shade
number for your application. Select a shade number by the shade knob (Shade guide Table No.1).The shade
goes darker from9 to 13 gradually by turningknob 1<2.
PRODUCT FEATURES
The helmet is designed & equipped with a special turn over (up Er down) headband mechanism. When the
user lifts the helmet, the headband mechanism aligns the helmet's centre of gravity to with the user's head.
This greatly reduces fatigue of the user's head (and neck) making the user more comfortable when working.
When welding, the helmet automatically changes the filter screenfromclear to dark in 1/25,000 sec. The
delay time from dark to clear is set between 0.2 sec and 1 sec, which can be adjusted by the delay knob.
The helmet utilises high performance solar cells as a power supply and 2 built-in 3V lithium batteries
(CR2032) as power back-up. The power is switched off automatically within 10-15mins of stopping work.
Under normal welding conditions, users can expect a battery lifetime of more than a year. The lithium
batteries can be replaced by ones of the same size and specification when exhausted.
The helmet is in full conformity with related DIN,ISO,EN safety standards and ANSI Z87.1-2010 standards.
The ultra -high performance of UV/IR auto -darkening filters provide full protection for the user's eyes and
face against UV/IR radiation during the entire welding process, even in the light state. The UV/IR protection
level is up to Shade 16(DIN) at all times, which increases comfort during welding work.
Page2 BLUERANGE

WARNING
The auto -darkening welding helmet is not suitable for laser welding or Oxyacetylene welding.
Never place the helmet and auto -darkening filter on a hot surface.
Never open or tamper with the auto -darkening filter.
The auto -darkening welding helmet will not protect against severe impact hazards.
The helmet will not protect against explosive devices or corrosive liquids.
Do not make any modifications to either the filter or helmet, unless specified in this manual.
Do not use replacement parts other than those specified in this manual.
Unauthorised modification and replacement parts will void the warranty and expose the
operator to the risk of personal injury.
Should the helmet not darken upon striking an arc, stop welding immediately and contact your
supervisor or your dealer.
Do not immerse the filter in water.
Do not use any solvents on the filter's screen or helmet components.
Use only at temperature: -5°C --+55°C.
Storing temperature: -20°C -+70°C.
Keep filter away from liquid and dirt.
Clean the filter's surfaces regularly, do not use strong cleaning solutions. Always keep sensors
and solar cells clean by using a clean, lint -free tissue/cloth.
Regularly replace the cracked/scratched/pitted front cover lens.
Severe personal injury could occur if the user fails to follow
the aforementioned warnings, and/or operating instruction.
See spare parts list on back cover.
TROUBLESHOOTING
Irregular Darkening Dimming
Headband has been set incorrectly and there is an uneven distance from the eyes to the filter's
lens. (Reset headband to reduce the difference to filter.)
Auto -darkening Filter Does Not Darken Or Flickers
Turn the sensitivity knob to "HI" position
Front cover lens is soiled or damaged (change the cover lens)
Sensors are soiled (clean the sensors' surfaces)
Welding current is too low.
Slow Response
Operating temperature is too low (do not use at temperature below -5°C)
Poor Vision
Front/inside cover lens and/or filter lens are soiled (change lens)
There is insufficient ambient light.
Shade number is incorrectly set (reset the shade number).
The protective film of the front/back cover lens has not been peeled off.
Welding Helmet Slips
Headband is not adjusted properly (readjust headband)
Warning: Operator must stop using the auto -darkening welding helmet immediately if the problems
mentioned above cannot be corrected. Contact the dealer.
BLUERANGE Page 3

LENS & HELMET MAINTENANCE
Replacingthefrontcoverlensif it is damaged (cracked, scratched, soiled or pitted)
Step1:Take out the old front cover lens.
Step2: Place the new cover lens into the right position.
TECHNICAL SPECIFICATIONS (UN09)
Viewing Area: 92 x42mm
Size of Cartridge: 110x90x1Omm
Light state: DIN4
Darken state: DIN 9-13
Switching Time: 1/25,000s
Operating Temperature: -5°C—+55°C
Storing Temperature: -20°C—+70°C
Helmet Material: High -impact resistant plastic/Polyamide Nylon.
TotalWeight:500g
Page 4 ZBLUERANGE

SHADE GUIDE TABLE (No.1)
Arc Current (Amperes)
0.5 2.5 10 20 40 80 125 175 225 275 350 450
Welding Process 1 5 15 30 60 100 150 200 250 300 400 500
111111111111111111111111
SMAW 9 10 11 12 13 14
MIG (heavy) 10 11 12 13 14
MIG (light) 10 11 12 13 14 15
TIG, GRAW 9 10 11 12 13 14
MAG/CO2 10 11 12 13 14 15
SAW 10 11 12 13 14 15
PAC 11 12 13
PAW 8 9 10 11 12 13 14 15
Note:
•SMAW - Shielded Metal Arc Welding •MAGICO2 - Metal Active Gas Welding (CO2)
•MIG(heavy) - MIG on heavy metals •SAW - Shielded Semi - Automatic Arc Welding
•MIG(light) - MIG on light alloys •PAC - Plasma Arc Cutting
•TIG. GRAW - Gas Tungsten Arc Welding (GRAW)(TIG) •PAW - Plasma Arc Welding
4/5-8 /9-13 WYT 1/1 / 1 / 2 379
Light state scale no
Lightest dark state scale no
Darkest state scale no (if applicable)
Lightest dark state scale no
Darkest state scale no (if applicable)
Manufacture's identification
Optical class
Diffusion of light class
Variations in luminous transmottance class
Angel dependence of luminous teansmittance class(optional)
Number of this standard
BLUERANGE Page 5

PARTS LIST- HELMET
PARTS LIST & ASSEMBLY
I. Outside Protection Plate
2. Lens
3. Potentiometer knob
4. Inside Protection Plate
5. Shell(welding mask)
6.2 XRound Washer
7. Time —delay Return Switch
8. 2 x Slid— bar
9.3 x Square Washer
10. Adjustable LimitationWasher
11. 2 x Block Nut
12.Sweatband
13.FrontHeadband
14. Adjustable Headband
IS. Adjustable Knob
Page 6
10 10
2
I ixo
.00.ri
14 15
BLUEFRANGE®

Statutory requirements and regulations
REGULATION(EU) 2016/425: European regulation for Personal protective devices
General
BLUERANGE can not, in general terms, accept responsibility for damage incurred by the owner, user
other persons using the safety product or third parties, which results either directly or indirectly
from incorrect use and/or maintenance of the safety product, including use of the product for
any purpose other than that for which it was supplied and/or the non compliance or incomplete
observance of the instructions contained in this user manual and/or in connection with repairs to
the safety product which have not been carried out by us or on our behalf. Our General Sales and
Supply conditions are applicable to all transactions. BLUERANGE continually strives to improve
its products and reserves the right to change the specifications mentioned in this manual without
prior notification.
ZBLU ERAN GE Page 7

Warning
The European guideline "Personal Protection REGULATION(EU) 2016/425" stipulates that only
inspected protective equipment bearing the CE mark may be traded and used. Use of substitute,
none -original spare parts, invalidates the CE approval and, also, all rights regarding guarantee,
whereby the user and, also, the person initially marketing these spare parts, shall be punished by
the relevant authorities of the EEC member countries, whereby additionally, the entire product will
be excluded from use and withdrawn from the commercial transactions respectively. Original spare
parts can be recognized by the affixed code number, supplemented with the manufacturer's mark
and the "CE approval" possibly supplemented with a year of applicability.
Guarantee
BLUERANGE will repair or, if necessary, replace this product free of charge in the event of a mate-
rial or manufacturing defect within 12 months of the purchase date, provided that the product has
only been subjected to normal usage in accordance with the user manual. The guarantee is invali-
dated if the type or serial number marking is modified, removed or made illegible.
Contact Details
BLUERANGETools
POBOX29
BOOTLE
MERSEYSIDEL201EJ
email: [e-mail]
phone: [phone]
Parts list
Image Name PartNumber
Outside Big Lens 115*98*1mm UNO9OUTSIDEBIGLENS
Inside Small Lens
96.5*67*1mm UNO9INSIDESMALLLENS
_
_
•
Helmet Headgear UNO9AUTOFILTERSP
Auto Darkening Helmet Filter UNO9HEADGEARSP
Page 8 BLUERANGE