BlueRhino Endless Summer 450000 Series User manual

Owners Manual
Manual del Usuario
Model No.
200209
U.S. Patent Number: 6,470,877; All Other
Foreign Patents May Apply.
WARNING
FOR YOUR SAFETY
For Outdoor Use Only
(Outside any enclosure)
Solamente Para Uso En
Exteriores
(Fuera de cualquier recinto)
WARNING
FOR YOUR SAFETY
Improper installation,
adjustment, alteration,
service or maintenance
can cause injury or property
damage. Read the installation,
operation and maintenance
instructions thoroughly before
installing or servicing this
equipment.

Contact 1-800-762-1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 200209 outdoor patio heater 7/28/04
1
Contact 1-800-762-1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 200209 outdoor patio heater 7/28/04 2
WARNING
FOR YOUR SAFETY
For Outdoor Use Only
(Outside any enclosure)
WARNING
FOR YOUR SAFETY
1. Gas leaks may cause a re or
explosion which can cause
serious bodily injury or death,
or damage to property.
2. You must follow all leak
checking procedures as
outlined in step 12 before
operating this unit.
3. Never use an open ame to
check for leaks.
WARNING
FOR YOUR SAFETY
Do not store or use gasoline
or other ammable vapors or
liquids in the vicinity of this or
any other appliance.
WARNING
FOR YOUR SAFETY
Improper installation,
adjustment, alteration, service
or maintenance can cause
injury or property damage.
Read the installation, operation
and maintenance instructions
thoroughly before installing or
servicing this equipment
WARNING
California Proposition 65:
Chemicals known to the state of
California to cause cancer, birth
defects, or other reproductive
harm are created by the
combustion of propane.
WARNING
FOR YOUR SAFETY
• Purchaser assumes all risk in
the assembly and operation
of this unit. Failure to follow
this manual’s WARNINGs
and instructions can result in
severe personal injury, death
or property damage.
• Do not use in an explosive
atmosphere. Keep heater away
from areas where ammable
liquids, gasoline, vapors, or
explosives are stored or used.
WARNING
FOR YOUR SAFETY
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open ame.
3. If odor continues, immediately
call your gas supplier.

Contact 1-800-762-1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 200209 outdoor patio heater 7/28/04
1
Contact 1-800-762-1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 200209 outdoor patio heater 7/28/04 2
Table of Contents
Safety First! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Assembly Instructions
Component Listing & Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
General Components & Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Additional Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Step 1 Attach Legs to Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Step 2 Attach Platform to Legs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Step 3 Attach Weight Plate to Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Step 4 Insert Gas Line Through Platform / Attach Shroud Cover . . . . . .8
Step 5 Attach Engine to Post . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Step 6 Attach Engine/Post to Platform . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Step 7 Connect Gas Line to Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Step 8 Assemble dome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Step 9 Attach dome to emitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Step 10 Secure Gas Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Step 11 Connect Gas Line To Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Step 12 Check for Leaks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Step 13 Replace Engine Access Panel . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Step 14 Install Igniter Battery (Electronic Ignition Models Only . . . . . . 13
Operation
Before Turning Gas Supply ON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Before Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Re-Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Operation Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
The use and installation of this product must conform to local codes. In absence
of local codes, us the National Fuel and Gas Code, ANSI Z223, 1/NFPA 54,
Storage and Handling of Liquid Petroleum Gases, ANSI/NFPA 58 or CSA B149.1,
Natural Gas and Propane Installation Code.
Save these instructions
for future reference. If you
are assembling this unit for
someone else, give this
manual to him or her to
save for future reference.

Contact 1-800-762-1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 200209 outdoor patio heater 7/28/04
3
Contact 1-800-762-1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 200209 outdoor patio heater 7/28/04 4
Safety First!
Read and become familiar with this entire manual, especially the following
precautions.
If you are unsure of anything in these instructions, STOP and contact
1-800-762-1142 for assistance.
Caution: This appliance is for outdoor use only (outside any
enclosure). Always make sure there is fresh air ventilation.
• Always maintain at least 36” clearance (top) and 24” clearance (side)
from combustible materials.
• Always place heater on a hard and level surface.
• Do not use if the wind velocity is greater than 10 miles per hour.
• Unit will operate at reduced efficiency below 40ºF (5ºC).
• Keep sprinklers and other water sources away from burner and controls.
• Always use extreme caution when near heater. Alert both children
and adults to the hazards of high temperatures, especially to avoid
burns or clothing catching fire.
• Young children and pets should be carefully supervised when they
are in the area of heater.
• Do not hang clothing or other flammable materials either on or near
heater.
• Any guard or other protective device removed for servicing the
heater must be replaced prior to operating the heater.
• Certain materials or items, when stored under heater, will be subjected
to radiant heat and could be seriously damaged.
• Do not alter heater in any manner.
• The pressure regulator and hose assembly supplied with the appliance
must be used and replacements must be those specified by the
manufacturer.
• Inspect heater before each use. If a damaged part is detected, do not
operate until an original equipment replacement part has been properly
installed. Use of unauthorized parts will void warranty and create an
unsafe condition.
• Do not attempt to use this appliance without a functional factory-
supplied gas regulator in place. If regulator becomes damaged, use only
a factory-supplied replacement.
• Prior to operating heater, replace any guards or protective devices
removed for servicing.
• During operation, do not touch burner assembly. The surface of heater’s
emitter can reach temperatures approaching 1600ºF.
• After shutdown, do not touch burner assembly until heater has cooled
(approximately 45 minutes after use).
Notice: This product should not be used with any fuel other than liquid
propane. Use of other fuels will detract from heaters performance and will
void your warranty.
Before you do anything else,
read and understand all
precautions in Safety First!
WARNING
FOR YOUR SAFETY
• Purchaser assumes all risk in
the assembly and operation
of this unit. Failure to follow
this manual’s WARNINGs
and instructions can result in
severe personal injury, death
or property damage.
• Do not use in an explosive
atmosphere. Keep heater
away from areas where
ammable liquids, gasoline,
vapors, or explosives are
stored or used.
Rhino
Blue
(Push in)
ON
Push
Push
Ignitor
Ignitor
Pilot
OFF
24”
36”

Contact 1-800-762-1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 200209 outdoor patio heater 7/28/04
3
Contact 1-800-762-1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 200209 outdoor patio heater 7/28/04 4
Caution: Liquid propane (LP) gas is flammable and hazardous if
handled improperly. Become aware of the characteristics before
using any LP product.
• LP Characteristics – Flammable, explosive under pressure, heavier than
air - settles in pools in low areas.
• In its natural state, propane has no odor. For your safety, an odorant is
added that smells like rotten cabbage.
• Contact with LP can cause freeze burns to skin.
• This heater is shipped from the factory for LP gas use only.
• Use only Department of Transportation (DOT) approved “20 lb.” LP gas
tanks (same as those commonly used on gas grills) with Acme / Type 1 /
QCC safety valves. These valves can be quickly identified because they
have external and internal threads.
• Never use an LP tank with a damaged body, valve, collar, or footring.
• Dented or rusted LP tanks may be hazardous and should be checked by
your LP gas supplier.
• The tank supply system must be arranged for vapor withdrawl.
• The tank used must include a collar to protect the tank valve.
• When heater is not in use, turn LP tank OFF.
• Always perform a leak test on gas connections whenever a tank is
connected. Never use a flame to test for leaks. Do not smoke while
performing a leak test.
Caution: It is essential to keep the heater’s valve compartment,
burners, and circulating air passages clean.
• Spiders and insects can create a dangerous condition that may damage
heater or make it unsafe. Keep burner area clean of all spiders, webs, or
insects.
• Inspect heater before each use.
• Have heater inspected annually and repairs should be made by a
qualified service person.
• Check heater immediately if any of the following conditions exist:
• The smell of gas in conjunction with extreme yellow tipping of burner
flames.
• Heater does not reach proper temperature.
Note: At temperatures less than 40ºF, heat output will be reduced.
• Heater’s glow is excessively uneven
• Burner makes popping noises during use.
Note: A slight pop is normal when burner is extinguished.
• Carbon deposits may create a fire hazard. Keep dome and emitter clean
at all times.
• Do not clean heater with combustible or corrosive cleaners. Use warm,
soapy water.
• Do not paint engine, engine access panel or dome.
FOR YOUR SAFETY:
Beware of Spiders
Spiders or small insects can get
into the burner tube or other
openings of your heater, and
spin webs or build nests. These
obstructions can lead to gas
ow problems. It is important
to make frequent inspections of
these areas and clean them when
necessary.
Before operating your heater for
the rst time, be sure to check
for obstructions that may have
occurred during shipment.
Need a tank or gas?
Try Blue Rhino tank exchange service. It’s
easy, fast, safe, and available at tens of
thousands of conveniently located retail
outlets nationwide. You can purchase a
new full tank or exchange your empty for a
precision filled one.
For your nearest Blue Rhino retailer visit
www.bluerhino.com.
“20 lb.” LP Tank
Collar
Valve
Body
Foot
18”-19”

Contact 1-800-762-1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 200209 outdoor patio heater 7/28/04
5
Contact 1-800-762-1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 200209 outdoor patio heater 7/28/04 6
Components Part Re-order
Name Number
Finial . . . . . . . . . 56-01-103
Dome Cap . . . . . 56-01-104
Dome Nut . . . . . 56-01-208
Dome Plate . . . . 56-01-105
Dome Panel (3) . 56-01-107
Dome Rib (3) . . . 56-01-109
Bottom Plate . . . 56-01-111
Dome Bolt . . . . . 56-01-212
Emitter . . . . . . . . 56-01-118
Pilot Assembly . . 56-01-127
Injector . . . . . . . . 56-01-125
Knob . . . . . . . . . 56-01-156
Access Panel
Assembly . . . . . . 56-01-140
Impulse Ignitor . . 56-01-142
Valve . . . . . . . . . 56-01-304
Valve Housing
Assembly . . . . . . 56-01-146
Pole . . . . . . . . . . 56-01-158
Shroud . . . . . . . . 56-01-164
Platform . . . . . . . 56-01-165
Gas Line/ Regulator
Assembly . . . . . . 56-01-188
Legs (3) . . . . . . . 56-01-193
Base . . . . . . . . . 56-01-329
Weight Plate . . . 56-01-198
Hardware
Used in
Picture Qty Description Step(s)
1 Carriage Bolt 3
3/8-16 x 3-3/4” Zinc Plated Bolt
56-01-199
12 Bolt 1 & 2
1/4-20 x 3/4” Nickel
Plated Hex Head Bolt
56-01-200
1 Large Screw 2
1/4-20 x 1” Nickle Plated
Philips Head Screw
56-01-202
4 Small Screw 5
1/4-20 x 3/8”Stainless Steel
Philips Truss Head Screw
56-01-2327
3 Dome Screw 8
5/32-32 x 1/4” Stainless Steel
Round Head Screw
56-01-205
12 Small Lockwasher 1 & 2
M6 Nickel plated Lockwasher
56-01-328
1 Large Lockwasher 3
M10 Nickel Plated
56-01-207
1 Large Nut 3
3/8-16 Nickel Plated Hex Nut
56-01-330
1 Medium Nut 8
3/8-16 Stainless Steel Hex Nut
56-01-208
15 Small Nut 1, 2 & 9
1/4-20 Nickel Plated Hex Nut
56-01-209
1 Gas Line Clip 2
56-01-213
1 Allen Wrench 6
56-01-215

Contact 1-800-762-1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 200209 outdoor patio heater 7/28/04
5
Contact 1-800-762-1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 200209 outdoor patio heater 7/28/04 6
Assembly Instructions
General Components & Features
Familiarize yourself with all components before proceeding. Refer to page 5 for hardware and components, and page 21
for specifications.
The white ceramic cone in the top of the engine is an important piece. DO NOT REMOVE.
Do NOT attempt assembly unless all components are available. If you believe a component is missing or damaged,
contact 1-800-762-1142 for assistance.
Note: All hardware is mounted on a cardboard pack and numbered to match their assembly step.
Additional Requirements
The following items are not included, but are necessary for the proper assembly of your heater. Do NOT attempt to
assemble without proper tools. A hex (Allen) wrench is necessary and is included in the parts bag.
(1) 7/16” Wrench
(1) 9/16” Wrench
(1) 7/16” Socket Wrench
(1) #2 Phillips Head Screwdriver
(1) Leak Detection Solution (Instructions on how to make solution are included in step 12)
(1) Precision Filled LP Gas Grill Tank with Acme Type 1 external threaded valve connection (4-5 gallon size)
Note: You must follow all steps to properly assemble heater.
Note: Unpacking note for 200209 patio heater.
When unpacking your heater from the carton, you will find that the
engine assembly and the base have been bolted together for shipping
purposes. Remove the three nuts at the top of the base and separate
the engine from the base. Retain these nuts for use in Step 9.
You are now ready to begin assembly of your patio heater.
Step 1 – Attach Legs to Base
Secure Legs to Base using (2) Small Bolts, (2) Smal Lock Washers and
(2) Small Nuts per leg. Finger tighten only.
Do not fully tighten until Step 2.
Attach small ‘S’ hook on Tank Restraint Chain to left leg.

Contact 1-800-762-1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 200209 outdoor patio heater 7/28/04
7
Contact 1-800-762-1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 200209 outdoor patio heater 7/28/04 8
Step 3 – Attach Weight Plate to Base
Lay Base Assembly on its side.
Place Weight Plate in Base, feet out.
Note: If you plan to anchor your heater permanently, be sure to line up
two outer holes in Base with those in Weight Plate so that your anchor
bolt will pass through both holes.
Insert Carriage Bolt through center holes of Base and Plate.
Using 9/16” wrench, secure Plate to Base using (1) Large Lock Washer
and (1) Large Nut.
Place Base Assembly upright.
Step 2 – Attach Platform to Legs
Line up hole in Clip with small threaded hole on bottom of Platform.
Attach Clip loosely to Platform with (1) Large Screw.
Note: Do not tighten until step 10.
Using 7/16” wrench, secure Platform to Legs using (2) Small Bolts, (2)
Small Lock Washers and (2) Small Nuts per Leg. Tighten fully.
Fully tighten all nuts and bolts from Step 1.
TIP:
To tighten use a 7/16” wrench on Bolt and a 7/16” socket wrench on
Nut.

Contact 1-800-762-1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 200209 outdoor patio heater 7/28/04
7
Contact 1-800-762-1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 200209 outdoor patio heater 7/28/04 8
Step 5 – Attach Engine to Post
Lay Engine Assembly on its side, using carton for support.
Remove and save Control Knob.
Remove and save Engine Access Panel by removing (1) black
Thumbscrew from bottom of Access Door.
Disconnect wire from Igniter by gently pulling wire from back of box.
Align (4) holes in top of Post with (4) holes in bottom of Engine.
Note: One hole is at a different level than the rest. Make sure that all 4
holes line up properly.
Insert (4) Small Screws enough to hold Engine in place. They will be fully
tightened at the end of Step 7.
Note: Do not replace Engine Access Panel until Step 13.
Step 4 – Insert Gas Line through Platform/Attach Shroud Cover
Insert Gas Line up through large hole in Platform from underneath
between center and left leg as shown in illustration.
Slide Shroud Cover over Gas Line, then over Platform/Leg assembly
until bottom of Shroud rests on Base.

Contact 1-800-762-1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 200209 outdoor patio heater 7/28/04
9
Contact 1-800-762-1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 200209 outdoor patio heater 7/28/04 10
Step 6 – Attach Engine/Post to Platform
Insert end of Post without holes over Gas Line, being careful not to bend
Gas Line.
Slide Post into collar of Platform so Post rests completely on Platform.
Tighten bottom three setscrews with hex (Allen) wrench supplied.
Make sure Post is perpendicular to Base.
Use top three setscrews to adjust Post’s angle as necessary.
Tighten all six setscrews.
Note: Post must be perpendicular to Base. Failure to do so will
adversely affect burner performance.
Step 7 – Connect Gas Line to Engine
Attach Gas Line to Control Valve:
Pull collar of Gas Line back.
Insert Gas Line over Control Valve.
Release collar and it should lock in place. (Tip – push Gas Line up from
bottom of Post to make a good seating before releasing the collar.)
Gently tug on line to test for proper connection. If Gas Line moves
it is not properly connected. Do not proceed until you have a proper
connection.
Fully tighten the (4) screws from Step 5.

Contact 1-800-762-1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 200209 outdoor patio heater 7/28/04
9
Contact 1-800-762-1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 200209 outdoor patio heater 7/28/04 10
Step 8 – Assemble dome
Note: Each dome section has a pin mounted in place in the rolled bottom
edge. If necessary for proper alignment of dome sections, loosen each
screw prior to further assembly and retighten after sections are aligned.
• With the large side facing up, slide a dome rib on to the same side
of one dome section as the pin. Slide two dome sections together,
allowing the exposed end of the pin slide into the rolled edge of the
next dome section. Line up hole in dome with threaded hole in pin.
• Insert one Dome Screw and secure loosely.
• Repeat procedure to complete the assembly of all three sections.
• Slide Dome bolt through bottom check plate (with small center hump),
being sure that the rolled edge faces down.
• Slide Dome bolt from previous step through the center of the
assembled dome sections, and be sure that the rolled edge of the
check plate fits inside of the ends of the three Dome Ribs. Also be
sure that the slots in the check plate line up with the holes on the
dome sections.
• Slide the other check plate over the Center bolt with the rolled edge
facing up, again making sure that the plate fits inside of the Ribs and
the holes line up with those in the dome.
• Spin the Dome nut all the way down the bolt, clamping all of the
pieces in place, making sure that all of the humps fit inside one
another.
• Fully tighten all of the screws in the rolled edge.
• Slide Dome Cap over Dome Bolt, lining up notches in cap with Dome
Ribs. Thread on finial until tight.
Step 9 – Attach Dome to Emitter
Line up holes in dome assembly with the studs from the emitter
assembly and lay dome assembly in place. Secure with three nuts.
Place dome cap over center bolt, making sure that the three slots in cap
lay over each Rib
Thread on finial until tight.

Contact 1-800-762-1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 200209 outdoor patio heater 7/28/04
11
Contact 1-800-762-1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 200209 outdoor patio heater 7/28/04 12
Caution
Before you attempt to use
a propane tank, understand
all tank and propane related
precautions in Section #1 -
“Safety First.”
Caution
Your Endless Summer® Heater
has been checked at all
factory connections for leaks.
Recheck all connections, as
movement in shipping can
loosen connections. Check
for leaks even if your unit was
assembled for you at the store.
SECTION VIEW
BOTTOM VIEW
gas line clip gas line
Step 11 – Connect Gas Line to Tank
The pressure regulator and hose assembly supplied with the appliance
must be used and replacements must be those specified by the
manufacturer.
• Slide full Propane Tank onto Heater Base.
• Attach Gas Line to Tank by turning black plastic knob clockwise over
Tank valve until tight.
Note: Be careful not to kink flexible hose of Gas Line.
• Secure tank in place by attaching loose end of Tank Restraint Chain to
hole in right leg.
Step 10 – Secure Gas Line
Make sure angled side of Gas Clip pokes up through large hole in
Platform.
Tighten screw until Gas Line is held securely in place.
Stand Heater upright.

Contact 1-800-762-1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 200209 outdoor patio heater 7/28/04
11
Contact 1-800-762-1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 200209 outdoor patio heater 7/28/04 12
Step 12 – Check for Leaks
• Make 2-3 oz. of leak check solution by mixing one part liquid
dishwashing soap and three parts water.
• Turn tank valve ON.
• Check Gas Line / Control Valve for leaks:
• Spoon several drops of solution onto Gas Line and Control Valve
connection.
• Inspect the solution at the connection to look for bubbles.
• If NO bubbles appear, then the connection is secure.
• If bubbles appear, there is a leak -
• Turn Tank valve OFF.
• Loosen screw on Clip.
• Release Gas Line fitting from control valve and re-attach making sure
connection is secure (see Step 7).
• Retighten Clip.
• If you continue to see bubbles after several attempts, contact
1-800-762-1142 for assistance.
Check Gas Line / Tank valve for leaks:
• Turn tank valve ON.
• Spoon several drops of solution onto Gas Line and Tank valve
connection.
• Inspect the solution at the connection to look for bubbles.
• If NO bubbles appear, then the connection is secure.
• If bubbles appear, there is a leak:
• Turn Tank valve OFF.
• Release Gas Line fitting from Tank valve and re-attach making sure
connection is secure (see Step 11).
• If you continue to see bubbles after several attempts, contact
1-800-762-1142 for assistance.
• Turn Tank Valve OFF.

Contact 1-800-762-1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 200209 outdoor patio heater 7/28/04
13
Contact 1-800-762-1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 200209 outdoor patio heater 7/28/04 14
Step 13 – Replace Engine Access Panel
• Slide Igniter wire onto Igniter post.
• Slide tab at top of Access Panel into slot in Emitter bottom.
• Rotate Panel down until holes line up at bottom.
• Secure Access Panel in place with thumbscrew.
• Replace Control Knob.
Step 14 – Install Igniter Battery
Note: This step is required only for models with electronic ignition.
• Remove battery cover cap by turning cap counterclockwise.
• Install (1) AA battery. Negative end of battery goes in first.
• Replace battery cover cap by turning cap clockwise.
Note: Once you have successfully completed assembly steps 1-14 you
are ready to begin operating your heater.

Contact 1-800-762-1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 200209 outdoor patio heater 7/28/04
13
Contact 1-800-762-1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 200209 outdoor patio heater 7/28/04 14
Operation
Caution: Do NOT attempt to operate heater until you have read and
understand all precautions in section 1 “Safety First.”
Before Turning Gas Supply ON
• Your heater was designed and approved for OUTDOOR USE ONLY.
DO NOT use it inside a building, garage, or any other enclosed area.
• Make sure surrounding areas are free of combustible materials,
gasoline, and other flammable vapors or liquids.
• Ensure that there is no obstruction to air ventilation.
• Be sure all gas connections are tight and there are no leaks.
• Be sure the access panel is clear of debris.
• Be sure any component removed during assembly or servicing is
replaced and fastened prior to starting.
Before Lighting
• Heater should be thoroughly inspected before each use, and by a
qualified service person at least annually.
• If relighting a hot heater, always wait at least 5 minutes.
• Inspect the hose assembly for evidence of excessive abrasion, cuts,
or wear. Suspected areas should be leak tested. If the hose leaks, it
must be replaced prior to operation. Only use the replacement hose
assembly specified by manufacturer.
Lighting
Note: This heater is equipped with a Pilot Light that allows for safer
startups and shutdowns. Pilot must be lit before Main Burner can be
started.
• Turn Tank Valve OFF.
• Push Control Knob IN and turn to OFF.
• Wait 5 minutes for any gas to clear.
• Turn Tank Valve ON.
• Open Viewing Hole by sliding cover to either side.
• Push Control Knob IN and rotate to Pilot position.
• Note - For initial start or after any tank change, hold Control Knob IN
for 2 minutes to purge air from gas lines before proceeding.
• Push Igniter button once. Pilot Light flame will appear and be visible
through Viewing Hole.
• Release Control Knob after 30 seconds. Pilot Light will remain lit.
If not, return to step 1.
• Turn Control Knob to ON. Main Burner will light immediately. Flame is
visible through Viewing Hole. If not, return to step 1.
WARNING
FOR YOUR SAFETY
• Do NOT attempt to operate
heater until you have
read and understand all
precautions in Section 1
“Safety First.” Failure to
do so can result in serious
personal injury, death, or
property damage.
• If at any time you are unable
to light burner and smell
gas, wait 5 minutes to allow
gas to dissipate before
attempting to light heater.
• Do NOT touch emitter or
dome or move heater for at
least 45 minutes after use.
OFF
OFF
LOW
LOW
Pilot
Pilot
(Push in)
HIGH
HIGH
Pilot
Pilot
(Push in)
HIGH
HIGH
LOW
LOW
OFF
OFF
View Hole

Contact 1-800-762-1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 200209 outdoor patio heater 7/28/04
15
Contact 1-800-762-1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 200209 outdoor patio heater 7/28/04 16
WARNING
FOR YOUR SAFETY
Be careful when attempting
to manually ignite this heater.
Holding in the control know for
more than 10 seconds before
igniting the gas will cause a
ball of ame upon ignition.
• If for some reason your ignitor fails to deliver a spark, your heater can
be started by inserting a lit match through the pilot view hole while
pushing the control knob in while in the PILOT position.
If you experience any ignition problem consult “Troubleshooting” on
page 17.
Caution: Avoid inhaling fumes emitted from the heater’s first use.
Smoke and odor from the burning of oils used in manufacturing will
appear. Both smoke and odor will dissipate after approximately 30
minutes. The heater should NOT produce thick black smoke.
Note: The burner may be noisy when initially turned on. To eliminate
excessive noise from the burner, turn the Control Knob to the Pilot
position. Then, turn the knob to the level of heat desired.
When heater is ON:
Emitter screen will become bright red due to intense heat. The color is
more visible at night.
Burner will display tongues of blue and yellow flame. These flames
should not be yellow or produce thick black smoke, indicating an
obstruction of airflow through the burners. The flame should be blue
with straight yellow tops.
If excessive yellow flame is detected, turn off heater and consult
“Troubleshooting” on page 17.
Re-lighting
Note: For your safety, Control Knob cannot be turned OFF without first
depressing Control Knob in PILOT position and then rotating it to OFF.
Turn Control Knob to OFF.
Wait at least 5 minutes, to let gas dissipate, before attempting to relight
Pilot.
Repeat the “Lighting” steps on prior page.
Shut Down
Turn Control Knob clockwise to Pilot. (Normally, burner will make a slight
popping sound when extinguished.) Burner will extinguish but Pilot will
remain ON.
To extinguish Pilot, depress Control Knob and continue to turn it
clockwise to OFF.
Turn Tank Valve clockwise to OFF and disconnect Regulator when
heater is not in use.
Note: After use, some discoloration of the emitter screen is normal.
WARNING
FOR YOUR SAFETY
Heater will be hot after use.
Handle with extreme care.

Contact 1-800-762-1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 200209 outdoor patio heater 7/28/04
15
Contact 1-800-762-1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 200209 outdoor patio heater 7/28/04 16
Operation Checklist
For a safe and pleasurable heating experience, perform this check before
each use.
Before Operating
q I am familiar with entire owner’s manual and understand all precautions
noted in “Safety First”.
q All components are properly assembled, intact and operable.
q No alterations have been made.
q All gas connections are secure and do not leak.
q Wind velocity is below 10 mph.
q Outdoor temperature is greater than 40 degrees F.
q Heater is outdoors (outside any enclosure).
q There is adequate fresh air ventilation.
q Heater is away from gasoline or other flammable liquids or vapors.
q Heater is away from windows, air intake openings, sprinklers and other
water sources.
q Heater is at least 36” clearance (top) and 24” clearance (side) from
combustible materials.
q Heater is on a hard and level surface.
q There are no signs of spider or insect nests.
q All burner passages are clear.
q All air circulation passages are clear.
q Children, pets, clothing, flammable materials and items that can be
damaged from radiant heat are away from the heater.
q Children and adults in the area have been alerted to the high
temperature hazards: especially burns and clothing fires.
q Children and adults in the area have been warned not to touch heater
near engine during operation and until unit has cooled.
After Operation
q Gas control is in OFF position.
q Gas tank valve is OFF
q Disconnect Gas line.
q Heater is upright in a secure location.

Contact 1-800-762-1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 200209 outdoor patio heater 7/28/04
17
Contact 1-800-762-1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 200209 outdoor patio heater 7/28/04 18
Troubleshooting
If the problem is: And this condition exists: Then do this
Pilot won’t light
Note: Heater operates at reduced efficiency
below 40ºF (5ºC).
Tank valve is closed
Blockage in orifice or pilot tube
Air in gas line
Low gas pressure with tank valve fully
open
Igniter fails
Open valve
Clean or replace orifice or pilot tube
Open gas line and bleed it (pressing
control knob in) for not more than 1
- 2 minutes or until you smell gas
Turn tank valve OFF and replace tank
Use match to light pilot; obtain new
igniter and replace
Pilot won’t stay lit Dirt built up around pilot
Connection between gas valve and
pilot assembly is loose
Thermocouple is not operating
correctly
Clean dirt from around pilot
Tighten connection and perform leak
check
Replace thermocouple
Burner won’t light Gas pressure is low
Blockage in orifice
Control knob is not in ON position
Turn tank valve OFF and replace tank
Clear blockage
Turn control knob to ON
Burner flame is low Gas pressure is low
Outdoor temperature is less than 40ºF
and tank is less than 1/4 full
Supply hose is bent or kinked
Control knob fully ON
Turn tank valve OFF and replace tan
Use a full tank
Straighten hose
Check burner and orifices for
blockage
Emitter glows uneven
Note: Bottom 1” of emitter normally does
NOT glow.
Gas pressure is low
Base is not on a level surface
Heater is level
Turn tank valvue OFF and replace tank
Place heater on a level surface
Clean burner
Carbon build-up Dirt or film on reflector and emitter Clean reflector and emitter
Thick black smoke Blockage in burner Remove blockage and clean burner
inside and outside

Contact 1-800-762-1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 200209 outdoor patio heater 7/28/04
17
Contact 1-800-762-1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 200209 outdoor patio heater 7/28/04 18
Maintenance
To enjoy years of outstanding performance from your heater, make sure
you perform the following maintenance activities on a regular basis:
Keep exterior surfaces clean.
Use warm soapy water for cleaning. Never use flammable or corrosive
cleaning agents.
While cleaning your unit, be sure to keep the area around the burner
and pilot assembly dry at all times. Do not submerge the control valve
assembly. If the gas control is submerged in water, do NOT use it. It
must be replaced.
Air flow must be unobstructed. Keep controls, burner, and circulating air
passageways clean. Signs of possible blockage include:
Gas odor with extreme yellow tipping of flame.
Heater does NOT reach the desired temperature.
Heater glow is excessively uneven.
Heater makes popping noises.
Spiders and insects can nest in burner or orifices. This dangerous
condition can damage heater and render it unsafe for use. Clean burner
holes by using a heavy-duty pipe cleaner. Compressed air may help
clear away smaller particles.
Carbon deposits may create a fire hazard. Clean dome and emitter with
warm soapy water if any carbon deposits develop.
Note: In a salt-air environment (such as near an ocean), corrosion occurs
more quickly than normal. Frequently check for corroded areas and repair
them promptly.
WARNING
FOR YOUR SAFETY
• Do NOT touch or move
heater for at least 45 minutes
after use.
• Dome is hot to the touch.
• Allow dome to cool before
touching.
TIP:
Use high-quality automobile wax to help maintain the appearance of
your heater. Apply to exterior surfaces from the pole down. Do not
apply to emitter screen or domes.

Contact 1-800-762-1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 200209 outdoor patio heater 7/28/04
19
Contact 1-800-762-1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 200209 outdoor patio heater 7/28/04 20
Storage
Between uses:
Turn Control Knob OFF.
Disconnect LP source.
Store heater upright in an area sheltered from direct contact with
inclement weather (such as rain, sleet, hail, snow, dust and debris).
If desired, cover heater to protect exterior surfaces and to help prevent
build up in air passages.
Note: Wait until heater is cool before covering.
During periods of extended inactivity or when transporting:
Turn Control Knob OFF.
Disconnect LP source and move to a secure, well-ventilated location
outdoors.
Store heater upright in an area sheltered from direct contact with
inclement weather (such as rain, sleet, hail, snow, dust and debris).
If desired, cover heater to protect exterior surfaces and to help prevent
build up in air passages.
Never leave LP cannister exposed to direct sunlight or excessive heat.
Note: Wait until heater is cool before covering.
Service
To learn how to service and procure parts for worn out, defective or
damaged components contact 1-800-762-1142 for assistance or e-mail
[email protected]. Please supply model number and
serial ID number for best service support. These numbers can be found on
a label on the rear of the Valve Housing.
Caution: Use only original equipment replacement parts. Use of
unauthorized parts or modification of parts will void warranty and
create an unsafe condition.
Caution: Always allow heater to cool before attempting service.