BlueSky Designs Mount'n Mover DP-T5 User manual

Attaching the Tobii I-13 or I-16 to a Mount’n Mover with a Tilt Plate
DP-T5
Tobii I-13
Tobii I-16
1DP-T5
page 1 of 4
The DP-T5 consists of the Quick Connect Receiver
(QCR), the DP-1x2, and four 8-32 x 2” screws.
QCR
DP-1x2
Use the four screws that come with the DP-T5 to go
through the Quick Release Plate (QRP), through the
DP-1x2 and into the Quick Connect Receiver (QCR)
Attach the DP-1x2 to the QCR with TWO of the
2” screws (use the two counter sunk holes)
Two Counter sunk holes
Recongure screws for an I-16
Quick Release Plate is attached using the other TWO 2”
screws. Go through the QRP, the DP-1x2, and into the
lower two holes on the QCR.
Counter sunk holes
two screws (8-32 x 2”) through
top two holes on the QRP
QRP
QRP
QCR
QCR
DP-1x2
Slide the DP-T5 onto the connecting grooves on
the Tobii device plate until it “clicks” in place.
Slide Up
Tobii Device Plate
Slide the DP-T5 onto the connecting grooves on
the Tobii device plate until it “clicks” in place.
Tobii
Device
Plate
Slide
Up
*
Close up of
counter sunk
holes at the top
x4 (8-32 x 2”)
(8-32 x 2”)
2Assemble QRP to DP-T5 Attach QCR to Tobii Device
3
DP-1x2
Attach QRP to DP-T5
2Attach QCR to Tobii Device
3
Attach the DP-1x2 to the QCR
1
DP-T5
Remove the
QRP from the
Mount’n Mover
Tilt Plate
The other two
screws are holding
the parts together.
Take apart before
step #2

Attaching the Quick Release Plate (QRP) to the Tilt Plate
Tobii I-13 fully attached and locked in place
DP-T5
page 2 of 4
First connect the notches on bottom of the
QRP to the protruding pins at the bottom of
the Tilt Plate.
Tilt
Plate
Tilt
Plate
Lock down the black Tilt Handle.
Tilt Handle
Lock
Down
Swing RED LOCK LEVER into lock position.
This locks down the Tilt Handle.
Push RED TAB and lift device up Tobii I-13 detached from Mount’n Mover
Remove Tobii I-13 or I-16 from Mount’n Mover
L
O
C
K
Notches
You can also remove
the device at the Quick
Release Plate (QRP)
QRP
Attach QRP to Tilt Plate
1Lock down Tilt Handle 2Lock Red Lever
3
Tobii locked in place
4

page 2 of 4
Set up for IR Remote Control Access for the I-13 and I-16
IR Remote Control
Access Window
QRP
(Oset to the right or left of the IR window)
*
(DP-T5 + DP-EXT)
List of Parts
1
x4
(8-32 x 2”)
DP-EXT
DP-1x2 QCR
Parts needed are the DP-T5, the DP-EXT (Extension Plate),and
the Quick Release Plate QRP (included with the Mount’n Mover)
Place DP-1x2 over QCR
2
Place the DP-1x2 over the
Quick Connect Receiver. Note
the counter sunk holes are at
the top and the red ag is on
the left
Two Counter sunk holes
Red Flag
Attach DP-EXT to DP-1x2 and QCR
3
Place DP-EXT over the DP-1x2 and use the four screws
to attach all three parts together. Note the countersunk
holes on the DP-EXT are facing up.
(8-32 x 2”)
x4 screws
Counter sunk holes
Attach QRP to DP-EXT
4
Place the Quick Release Plate (QRP) over the DP-EXT
and attach to the threaded inserts in the EXT with four
(8-32 x 1/4”) screws (labeled QRP to Device Plate)
(8-32 x 1/4”)
x4 screws
QRP
DP-EXT
assembled
extension
5Mount to the Tobii Device
Slide the Extension up onto the
connecting grooves on the Tobii
plate until it “clicks” in place
Slide
Up
page 3 of 4
DP-EXT
DP-1x2

Set up for I-13 and I-16 with a Universal Rotator (DP-UR)
Rotator used with Extension plate
for access to Infrared window.
Use two of the 8-32 x 2” screws through
two of the holes in the DP-UR, through
the DP-T5 spacer, and into the threaded
holes in the QCR. The other 2” screws
attach the spacer to the QCR.
Attach the Extension Plate (DP-EXT) to
the Rotator (DP-UR) with four screws
labeled “Attaching QRP to Rotator”
(8-32 x 3/16”). Note the Rotator knob
can be on left or right side.
page 4 of 4
No IR access
B
Set up for IR access
A
DP-T5
DP-EXT
DP-UR
Parts needed
1
Parts needed
1
Turn Rotator
2
Locate attachment holes
Attach DP-UR to DP-T5
3
Two screws
through DP-UR
Attach DP-EXT to DP-UR
Attach the QRP to the threaded
inserts on the DP-EXT with four
screws (8-32 x 1/4”) labeled
“QRP to Device Plate”.
Attach QRP to DP-EXT
5
Loosen
knob
QRP
4
The DP-T5 includes: Loosen the knob and spin
the Rotator to reveal the
attachment holes.
a
b
Spacer
QCR
DP-EXT
Knob can
be on left
or right
sides Turn Rotator
2
Attach DP-UR to DP-T5
3
(See above steps #2 + #3)
QRP
Attach the QRP to the threaded
inserts on the DP-UR with four
screws (8-32 x 3/16”) labeled
“QRP to Rotator”.
Attach DP-UR to QRP
4
DP-UR
countersunk
holes
Two screws
through
countersunk
holes into QCR
1. Spacer
2. QCR
and four 8-32 x 2” screws
DP-URDP-T5