Boat Lift Up-N-Over User manual

*NOT FOR LIFTING/LOWERING HUMANS
Cover 09/07/2017
INSTALLATION INSTRUCTIONS
FIX MARINE SUPPLY
[phone]
Special Notes: Improper installation-assembly, or overloading PWC lift
beyond rated capacity will void manufacturer’s warranty. Electrical
connection MUST be grounded with a GFCI device. Proper line voltage
only. No Generators! Generator use will void motor’s warranty!
1,5OO Lb.
Capacity

*NOT FOR LIFTING/LOWERING HUMANS
Page 1 09/07/2017
Caution: Failure to adhere to the following
instructions will void manufacturer’s warranty:
1.) (6) ¾” diameter bolts, 3” longer than piling’s
diameter, MUST be used to properly mount the
Up-N-Over™ to the piling. (not 5/8”, etc. ¾” only!)
2.) The “Piling-Mount Bracket” MUST be mounted to
piling PLUMB. Failure to do so will result in difficulty
to the user when rotating pwc back/forth over the
water, and back over the dock. (10”-12” piling req’d.)
3.) Do NOT operate Up-N-Over™ until you have
thoroughly GREASED the (8) grease zerks!
Lift will malfunction without ample grease!
4.) Electric motor MUST have FULL POWER while
under full load. Voltage drops resulting in less
than 115v/230v will void motor warranty. Have
“loaded” voltage verified by licensed electrician.
Proper line voltage only. No Generators!
Generator use will void motor’s warranty!
5.) Instruct users to REMOVE locking-pin before
attempting to rotate cradle arm.

*NOT FOR LIFTING/LOWERING HUMANS
Page 2 09/07/2017
Step 1 - Installing PILING-MOUNT bracket
1.) Place PILING-MOUNT bracket onto your piling,
ensuring the top is 42” above the dock’s
surface. Now, using heavy nails hang bracket
into place using staggered bolt holes. Be sure
bracket is 100% PLUMB!
Remember: Up-N-Over™ rotates 180°, so be
sure to choose the correct orientation for this!
Refer to photo on cover of this manual.
2.) Drill (6) holes using your PILING-
MOUNT bracket as your template.
These will be drilled in a cross-pattern.
Remember: ¾” diameter bolts only!
3.) Now install the (6) mounting bolts, and
tighten down onto 3” x 3” square washers.
Note: Stainless hardware recommended.

Step 2 – MAST installation
1.) Insert heavy-duty aluminum
mast into the HEAD ASSEMBLY.
Note: Be sure to orient the mast
correctly in the HEAD ASSEMBLY
so that the holes align with mast’s
cradle arm bolt holes.
Step 3 – HEAD ASSEMBLY to PILE MOUNT
- HEAD ASSY SWIVEL PIN
1.) With the mast positioned
into the HEAD ASSEMBLY,
install the PILE MOUNT in
between the swivel-brackets,
and lock into place with the
HEAD SWIVEL PIN. Be sure
not to lose your white nylon
bushing:
*NOT FOR LIFTING/LOWERING HUMANS Page 3 09/07/2017

*NOT FOR LIFTING/LOWERING HUMANS
Page 4 09/07/2017
Step 4 – CONNECT MAST to CRADLE ARM
1.) With CRADLE ARM in position on deck, raise mast
up a foot or two, and slide underneath. Finally
drop MAST into the CRADLE ARM and fasten with
supplied ½” stainless bolts (total of 3).
Step 5 – Attach GEARBOX to HEAD ASSEMBLY
1.) Mount CABLE WINDER assembly to
the HEAD ASSEMBLY.
2.) Connect GEARBOX® shaft to the
CABLE WINDER shaft.
3.) Attach motor to GEARBOX®, and
wind stainless cable as shown:

*NOT FOR LIFTING/LOWERING HUMANS
Page 5 09/07/2017
Step 6 – Connect stainless CABLE to CRADLE ARM
1.) With cable wound over the cable-winder drum, as
shown in photo on bottom of page 4, connect
cable to CRADLE ARM using the supplied ¾”
stainless bolt:
Step 7 – Aluminum BUNK attachement.
1.) Assemble the Aluminum Bunks to their brackets
at shown here:
2.) Then, mount the
Bunks into place
on CRADLE ARM.

*NOT FOR LIFTING/LOWERING HUMANS
Page 6 09/07/2017
Step 8 – Aluminum GUIDE POST attachement.
1.) Attach the aluminum GUIDE POST BRACKET to
the CRADLE ARM, and secure in place with
supplied stainless U-bolt.
2.) Be sure NOT to position GUIDE POST under the
motor/GEARBOX assembly! Damage to GEARBOX
will result when raising PWC.
3.) Finally, insert aluminum GUIDE POST into the
GUIDE POST BRACKET, and cover with supplied
PVC cover & cap.
Final Notes:
• Please remind, and remind again the users to NEVER ride a
PWC lift up/down. These are NOT for lifting humans.
• Do not operate lift without applying ample grease to the (8)
grease zerks.
• Be completely sure that the motor is recieving a full 115/230v
while under load, and not suffering from “voltage drop”.
Proper line voltage only. No Generators! Generator use will
void motor’s warranty!
• Do NOT allow your cable to go slack. Be sure not to “hit
bottom” with your CRADLE ARM, and always ensure that your
cable is wound properly on the grooved cable-winder.