bObsweep WP260011 User manual

OWNER’S MANUAL
How to employ your intelligent floor cleaner
bObsweep PetHair™ | Model WP260011

Congratulations!
Congratulations on your new intelligent floor cleaner! Bob is now at your service. To
see Bob at his best, please read the Quick Start Guide and this manual thoroughly.
Welcome to the bObsweep family and happy cleaning!
If you have any questions or concerns, feel free to contact our helpful team at
[email protected].

Remote Control
Important Safety
Instructions
Cleaning Schedule
17
36
Troubleshooting
& Checkup Test
64
4
Charging
Box Contents
& Anatomy
Parts &
Maintenance
21
45
6
Warranty
& FAQs
88
Senors
Get Bob
Ready to Clean
58
29
11
Cleaning Modes
End User
Agreement
94

Basic safety precautions should always be followed, including the following:
•To protect against electrical shock, do not immerse any part of Bob — with the exception of
his mopping cloth — into water or other liquids.
•Unplug Bob from outlet when not in use and before conducting maintenance.
•Do not operate Bob or his charging station if they have been damaged in any way.
If Bob is not working as he should, or has been dropped, damaged, left outdoors, or dropped
in water, contact our customer care center at [email protected].
•Do not handle Bob or his charging station with wet hands.
•Do not use Bob outdoors or on any wet surface.
•Bob is not intended for use by persons (including children) with reduced physical or mental
capabilities, or lack of experience and knowledge, unless under the close supervision of a
person responsible for their safety.
•Do not pull or carry the charging station by the cord, use the cord as a handle, close a door
on the cord, or pull the cord around sharp edges or corners. Keep the cord away from heated
surfaces. To unplug the cord, grasp the plug, not the cord itself.
•Do not mutilate or incinerate the battery, as it will explode at high temperatures.
•Do not attempt to open Bob’s charging station. Repairs on his station should only be carried
out by our qualified customer care center.
•Do not expose Bob’s charging station to high temperatures or allow moisture or humidity of
any kind to come into contact with it.
•Do not let Bob pick up toxic materials (chlorine bleach, ammonia, drain cleaner, etc.).
•Do not let Bob pick up anything that is burning or smoking, such as cigarettes, matches, or hot
ashes. Do not use Bob to pick up flammable or combustible liquids such as gasoline, nor use
him in areas where they may be present.
•Do not use Bob in an enclosed space filled with vapors given off by oil-based paint, paint
thinner, moth-proofing substances, flammable dust, or other explosive or toxic vapors.
Important Safety Instructions

• Leaks from battery cells can occur under extreme usage or temperature conditions. If the liquid
gets on skin, wash quickly with water. If the liquid gets into the eyes, flush them immediately
with clean water for a minimum of 10 minutes, and seek medical attention.
•Do not use Bob for anything other than his intended purpose, as specified in this manual.
Declaration of Conformity
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modifications or change to this equipment. Such modifications or change could void the user’s
authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

1
2
3 4
5
678
9
10
11
12
13 14
1 Bob, Your Intelligent Floor Cleaner
2 Charging Station
3 Main Brush
4 Charging Adapter
5 Remote Control
6 Flat Head Screwdriver
7 2 Side Brushes (1 Spare)
8 Cleaning Tool
9 Pack of Screws and Blindfold Stickers
10 Mop Attachment
11 2 Microfiber Mopping Cloths
12 HEPA Filter (Spare)
13 Owner’s Manual, Quick Start Guide, and Warranty Card
14 Bumper Stickers
Box Contents

7
42
1
3
Top View
1 Bumper
2 Transmitter
3 Cover Buttons
4 Display Screen
Anatomy

8
RL
1 2 4 7
3
5
8
9
10
6
1
Bottom View
1 Charging Plates
2 Front Wheel
3 Side Brush
4 Main Brush
5 ON/OFF Switch
6 Dustbin
7 UV Lamp
8 Battery
9 Left Wheel
10 Right Wheel

9
1
2
1 Remote Control
2 Charging Station

10
UV
DIRT
TROUBLE NR.
CAPACITY
AUTO SPOTWALL FOLLOW DOCK
MIN. CLEANING
CHARGING
READY
54321
Cover Buttons
1 UV
Turn UV lamp OFF/ON
2 PROGRAM
Select Bob’s cleaning program
3 MODE
Select Bob’s cleaning mode
4 CHARGE
Send Bob to his charging station
5 START
Send Bob to clean

Get Bob
Ready to Clean
Install Bob’s Side Brush 12
Charge Bob 13
Bob’s First Clean 14
Standby Mode 15

12
Before Bob’s first clean, you must install his side brush, which allows him to sweep
along corners, walls, and other hard-to-reach places.
Install Bob’s Side Brush
You may use the additional side brush and screws as spares.
1 2
Flip Bob over onto a flat surface. Place
the side brush over the empty socket
on Bob’s underside.
Secure Bob’s side brush using the flat
head screwdriver and short screw.

13
After installing Bob’s side brush, you must set him to charge.
To charge Bob:
Charge Bob
1 2
Plug the charging adapter into the side
of the charging station.
Place Bob on his charging station with
the metal plates on his underside sit-
ting on top of the nodes on his station.
If Bob can’t find his
charging station on
his own, the station
needs to be synced
(see page 24).
The charging station will save its last settings for up to 8 hours
after being disconnected or turned off.

14
UV
DIRT
TROUBLE NR.
CAPACITY
AUTO SPOT WALL FOLLOW DOCK
MIN. CLEANING
CHARGING
READY
Bob is now ready to clean! First, flip his power switch ON. Then, press START
on his cover — or AUTO on his remote — and he will clean on his default setting
(Robot mode).
Bob’s First Clean
OR

15
UV
DIRT
TROUBLE NR.
CAPACITY
AUTO SPOT WALL FOLLOW DOCK
MIN. CLEANING
CHARGING
READY
UV
DIRT
TROUBLE NR.
CAPACITY
AUTO SPOT WALL FOLLOW DOCK
MIN. CLEANING
CHARGING
READY
If Bob is left idle without charging or cleaning, his screen will go blank and he will
enter standby mode to preserve his battery. In standby mode, Bob will remain asleep.
You can also put Bob in and out of standby mode by pressing the power button on
his remote.
To get Bob back to cleaning:
Standby Mode
To wake Bob, press any button on his
cover or the power button on his remote.
Press START on his cover or AUTO on
his remote.
1 2

16
UV
DIRT
TROUBLE NR.
CAPACITY
AUTO SPOT WALL FOLLOW DOCK
MIN. CLEANING
CHARGING
READY
UV
DIRT
TROUBLE NR.
CAPACITY
AUTO SPOT WALL FOLLOW DOCK
MIN. CLEANING
CHARGING
READY
To send Bob to his charging station:
To wake Bob, press any button on his
cover or the power button on his remote.
1
Press CHARGE on Bob’s cover or remote.
2

Remote Control
Remote Control Buttons 18
Syncing Bob's Remote 20

18
4
3 2 8 1 5 6
7
9
8
8
8
Bob’s remote requires 2 AAA batteries (not included). Remove the batteries if you are
not using it on a regular basis. Keep the remote at room temperature.
1Power
2Auto
3 Corners
4UV
5Spot
6Charge
7Speed
8Navigational Arrows
9Pause
Remote Control

19
Power
• Puts Bob in and out of standby mode
Auto
•Bob will start cleaning on his default setting (Robot mode)
Corners
• Bob will clean along corners and walls (Wall Track™ mode)
UV
• Turns Bob's UV light OFF and ON again
Spot
•Bob will target a small area by traveling in a circle (Spiral Track™ mode)
Charge
•Sends Bob to his charging station
Speed
• Alternates between Bob's two speeds
Navigational Buttons
• Guide Bob forward, backward, left, or right
-Hold down the navigational buttons to keep Bob moving in the
desire direction.
Pause
• Pauses or resumes Bob’s movement
Flip Bob’s power switch
OFF to have him fully power
down. If Bob is left idle and
ON, he is in standby mode.

20
You will need to sync the remote if Bob is not responding to its commands. When you
do this, make sure Bob is not on his charging station.
To sync Bob’s remote:
Syncing Bob’s Remote
Flip Bob’s power switch
OFF.
While holding down the
PAUSE button on Bob’s
remote, flip Bob’s power
switch ON.
Bob will chirp twice to let
you know the sync was
successful.
1 32
If you do not hear Bob chirp, repeat the process.