Bodyworx L8000HG User manual

HOME GYM
L8000HG
OWNER’S MANUAL

-1-

-2-

-3-
PART LIST
PART NO: DESCRIPTION Q’TY
1. MAIN BASE 1
2. GUIDE ROD 2
3. LEFT BASE 1
4. RIGHT BASE 2
5. SELECTOR SHAFT 1
6. TOP PLATE 1
7. WEIGHT STACK 10
8. RUBBER DOUNT 2
9. VERTICAL BEAM 1
10. TOP CROSS BEAM 1
11. SEAT SUPPORT 1
12. SEAT ASSEMBLY UNIT 1
13. LEG EXTENSION/ARM CURL BAR 1
14. PRESS BAR 1
15. LEFT PEC DECK ARM 1
16. RIGHT PEC DECK ARM 1
17. PRESS PIN 1
18. SEAT 1
19. BACK SEAT 1
20. PULLEY BLOCK 2
21. FLOATING PULLEY BLOCK(A) 1
22. FLOATING PULLEY BLOCK(B) 1
23. WEIGHT STACK CABLE 1340MM 1
24. LAT BAR CABLE 3480MM 1
25. PEC DECK CABLE 2750MM 1
26. CURL BAR CABLE 3350MM 1
27. CHAIN 3
28. PEC DECK PAD 2
29. LEG EXTENSION/CURL PAD 6
30. LAT BAR 1
31. CURL BAR 1
32. PAD HOLDER 2
33. HANDLE PIPE 2
34. PULLEY 14
35. HAND GRIP 8
36. CHAIN HOOK 7
37. RUBBER BUMPER 2
38. PLASTIC BUSHING 10
39. RUBBER END CAP 2
40. RUBBER CAP 3
41. 50*50MM SQUARE END CAP 8
42. 38*38 MM SQUARE END CAP 2
43. 25*50MM SQUARE END CAP 2

-4-
PART LIST
PART NO: DESCRIPTION Q’TY
44. 25MM ROUND END CAP 6
45. 25MM ROUND BUSHING 1
46. QUICK PIN 1
47. OD48MM*ID13MM WASHER 1
48. PIN FOR WEIGHT SATCK 1
49. ADJUSTABLE POP PIN 1
50. STEEL PLATE (LONG) 1
51. STEEL PLATE (SHORT) 1
52. OIL BUSHING 6
53. PRESS BAR SHAFT 1
54. M12*75MM HEX BOLT 1
55. M10*125MM HEX BOLT 2
56. M10*75MM HEX BOLT 4
57. M10*70MM HEX BOLT 9
58. M10*45MM HEX BOLT 9
59. M10*30MM HEX BOLT 2
60. M10*25MM HEX BOLT 6
61. M8*115MM HEX BOLT 2
62. M8*65MM HEX BOLT 7
64. M8*15MM HEX BOLT 8
65. M10 NUT 2
66. M16 NYLON NUT 4
67. M12 NYLON NUT 1
68. M10 NYLON NUT 28
69. M8 NYLON NUT 3
70. M16 WASHER 4
71. M12 WASHER 2
72. M10 WASHER 60
73. M8 WASHER 20
74. SQUARE CAPψ26x□38 MM 2
75. PEDAL 1
76. WEIGHT COVER 2
77. ANKLE STRAPE 1
78. TRICEPS STRAPE 1
79. FASTENING 1
80. SPRING 1
81. M6*30MM HEX BOLT 1
82. M6 NYLON NUT 1
83. 50*100MM SQUARE END CAP 2
84. SPRING WASHER 2
85. PRESS BAR SHAFT 10MM 1
86. PAD HOLDER (LONG) 1
87. RUBBER BUMPER(SHORT) 1

STEP 01
1. PLACE RUBBER END CAP (39) ONTO BOTH ENDS OF LEFT BASE (03)
2. INSERT GUIDE RODS (02) TO LEFT BASE (03) WITH M10*25MM BOLT (60),
M10 WASHER (72) AS SHOWN.
3. ATTACH MAIN BASE (01) TO LEFT BASE (03) WITH M10*75MM BOLT (56),
M10 WASHER (72) AND M10 NYLON NUT (68) AS SHOWN.
FASTEN ALL BOLTS BY USING TOOL.
4. ATTACH VERTICLE BEAM (09) TO MAIN BASE (01) WITH M10*70MM BOLT
(57), M10 WASHER (72) AND M10 NYLON NUT (68) AS SHOWN.
5. ATTACH PEDAL(75)ONTOMAIN BASE (01) WITH PRESS BAR SHAFT 10MM
(85), M10 WASHER (72) AND M10 NYLON NUT (68) AS SHOWN.
-5-

STEP 02
1. ATTACH THE RUBBER DOUNT (08) ONTO THE GUIDE ROD (02).
2. SLIDE THE WEIGHT PLATE (07) AND TOP PLATE (06) OVER GUIDE ROD
(02).
GROOVED SIDE OF WEIGHT PLATES SHOULD FACE DOWN
3. INSTALL 25MM ROUND BUSHING (45) INTO THE SELECTOR SHAFT (05).
WITH PIN (46) THEN ATTACH THE SELECTOR SHAFT (05) INTO THE TOP
PLATE (06) AS SHOWN.
4. PLACE 50MM SQUARE CAP (41) ONTO FRONT BASE (01).
5. PLACE RUBBER CAP (40) ONTO BOTH ENDS OF RIGHT BASE (04).
6. ATTACH RIGHT BASE (04) TO MAIN BASE (01) WITH M10*75MM BOLT (56),
M10 WASHER (72) AND M10 NYLON NUT (68) AS SHOWN.
-6-

STEP 03
1. PLACE 50*100MM SQUARE CAP (83) ONTO TOP CROSS BEAM (10).
2. ATTACH TOP CROSS BEAM (10) ONTO THE VERTICLE BEAM (09) WITH
M10*70MM BOLT (57), M10 WASHER (72) AND M10 NYLON NUT (68) AND
CONNECT THE GUIDE RODS (02) TO THE TOP CROSS BEAM (10) AS
SHOWN.
3. ATTACH RUBBER BUMPER (37) TO THE VERTICLE BEAM (09).
4. ATTACH PULLEY BLOCK (20) TO THE VERTICLE BEAM (09), USE M8*60MM
BOLT (62) WITH M8 WASHER (73) AND M8 NUTS (69).
5. PLACE 38MM SQUARE CAP (42) ONTO VERTICLE BEAM (09).
-7-

STEP 04
1. PLACE 50MM SQUARE CAP (41) ONTO BOTH ENDS OF LEG EXTENSION
/ARM CURL BAR (13).
2. ATTACH SEAT SUPPORT (11) TO VERTICLE BEAM (09), WITH STEEL PLATE
(50) M10*125MM BOLT (55), M10 WASHERS (72), AND M10 NYLON NUT (68).
3. ATTACH SEAT ASSEMBLY UNIT (12) TO SEAT SUPPORT (11) AS SHOWN.
4. ATTACH LEG EXTENSION /ARM CURL BAR (13) TO SEAT SUPPORT (11).
5. ATTACH BACK SEAT (19) TO VERTICLE BEAM (09) AS SHOWN.
6. ATTACH SEAT (18) TO SEAT ASSEMBLY UNIT (12) AS SHOWN.
7. SLIDE PAD HOLDERS (32) INTO THE HOLE PROVIDED.
8. SLIDE PAD HOLDER (LONG) (86) INTO THE HOLE OF VERTICLEBEAM (09).
9. SLIDE LEG EXTENSION/CURL PADS (29) ONTO PAD HOLDERS (32) AND PAD
HOLDER (LONG) (86).
10. PLACE 25MM ROUND CAP (44) ONTO PAD HOLDERS (32) AND (86).
-8-

STEP 05
1. PLACE 50MM SQUARE CAP (41) INTO BOTH ENDS OF PRESS BAR (14).
2. INSTALL OIL BUSHING (52) INTO THE PRESS BAR (14).
3. RUBBER CAP (40) TO PRESS BAR (14) AS SHOWN.
STEP 06
1. ATTACH PRESS BAR (14) TO TOP CROSS BEAM (10) WITH PRESS BAR
SHAFT (53) AND OIL BUSHING (52) M16 WASHER (70) M16 NYLONNUT
(66) AS SHOWN.
2. ATTACH PEC DEC PAD (28) ONTO PEC DEC ARM (15&16) WITHM8*65MM
BOLT (62) M8 WASHER (73) AS SHOWN.
3. ATTACH HANDLE PIPE (33) AND HAND GRIP (35) TO PEC DEC ARM
(15&16) WITH M10 BOLT (60), M10 WASHER (72) AS SHOWN.
4. INSTALL PEC DEC ARM (15&16) TO PRESS BAR (14) WITH M16 WASHER
(70) AND M16 NYLON NUT (66) AS SHOWN.
5. PLACE PRESS PIN (17) INTO PRESS BAR (14) USE FASTENING (79)WITH
M6*30MM BOLT (81) M6 NYLON NUT (82) AND SPRING (80) AS SHOWN.
-9-

-10-

Make certain all cables are seated into all pulley grooves. A cable rubbing
against steel will peel the nylon coating, voiding warranty and resulting in
a need for replacement.
Pre-stretch the cables. Put the Weight Selector Pin in the bottom hole on the
weight stack. Pull on the cables with force, helping remove any kinks and
providing any initial cable stretch.
Be aware the cables can loosen and slightly stretch upon initial use.
The cables should be adjusted as tight as possible,
For better performance, apply a household lubricant (such as silicone) to
any adjustable areas and to the Guide Rods
-11-

-12-
---CABLE ASSEMBLY---
1. START WITH WEIGHT STACK CABLE 1340MM (23)
START ATTACH CABLE (23) WITH M12 BOLT AND WASHER (47) TO WEIGHT
STACK FASTEN THE OTHER END UP AND OVER AROUND PULLEY NO.1, DOWN
WITH CHAIN HOOK (36) AND CHAIN (27) AS SHOWN.
2. START WITH THE TOP LAT BAR CABLE 3480MM (24)
START BY THREADING THE END OF THE CABLE THE SMALL BALL OVER GET
INTO PULLEY NO.2, INTO OVER PULLEY NO.3, DOWN AND AROUND PULLEY
NO.4IN FLOATING PULLEY LOCK, UP AND OVER PULLEY NO.5AS SHOWN.
3. CONNECT THE PEC DEC CABLE 2750MM (25)
TAKE PEC DEC CABLE ONE END TO PEC DEC ARM AS PICTURED IN PEC DEC
ASSEMBLY, USING M10*30MM HEX BOLT (59), M10 NUT (65), M10 WASHER (72)
AND M10 NYLON NUT (68) TO SECURE CABLE TO ASSEMBLY, THEN THREAD
THE OTHER END OF CABLE OVER PULLEY NO.6, DOWN AND AROUND PULLEY
NO.7, IN PEC DEC PULLEY BLOCK (22) UP AND OVER PULLEY NO.8, USING
M10*30MM HEX BOLT (59), M10 NUT (65), M10 WASHER (72) AND M10 NYLON
NUT (68) TO SECURE CABLE TO ASSEMBLY.
4. START THE BOTTOM CURL BAR CABLE 3350MM (26)
START BY THREADING THE END OF THE CABLE WITHOUT THE BALL UNDER
PULLEY NO.9, UNDER PULLEY NO.10, UP AND AROUND PULLEY NO.11, IN
FLOATING PULLEY BLOCK, DOWN AND UNDER PULLEY NO.12, UP AND
AROUND PULLEY NO.13, IN FLOATING PULLEY LOCK, DOWN AND AROUND
PULLEY NO.14, UP AND WITH CHAIN HOOK (36) TO CHAIN (27) TOTIGHTEN.
NOTE: IF YOU FIND THAT THE CABLES ARE NOT LONG ENOUGH, USE THE
EXERCISE CHAIN AS AN EXTENSION WITH CHAIN HOOK AS
CONNECTORS.
INSTALL WEIGHT COVER (76) TO TOP CROSS BEAM (10) AND LEFT BASE (03).
SECURE USING M8*15MM BOLTS (64), M8 WASHER (73) AS SHOWN.
ATTACH HAND GRIP (35) TO LAT BAR (30) AND CURL BAR (31).
※ WARNING: MAKE SURE ALL CABLES DO NOT RUN OUT OF TRACK FROM ANY
OF PULLEYS WHILE YOU ARE IN USE EVERYTIME.

-13-

Distributed Exclusively by:
GPI Sports & Fitness
275 Wellington Road
Mulgrave, VIC, 3170
Australia.
-14-