Weider PRO 9930 User manual

®
USER’S MANUAL
Model No. WESY99300
Serial No.
The serial number is found in the
location shown below. Write the
serial number in the space above.
CAUTION
Read all precautio s a d i struc-
tio s i this ma ual before usi g
this equipme t. Save this ma u-
al for future refere ce.
Serial
Number
Decal
www.weiderfit ess.com
Visit our website at
QUESTIONS?
We are committed to providi g
complete customer satisfactio .
If you have questio s, or if there
are missi g parts, we will guar-
a tee complete satisfactio
through direct assista ce from
our factory.
TO AVOID UNNECESSARY
DELAYS, PLEASE CALL DIRECT
TO OUR TOLL-FREE CUS-
TOMER HOT LINE. The trai ed
tech icia s o our customer hot
li e will provide immediate
assista ce, free of charge.
CUSTOMER HOT LINE:
1-888-936-4266
Mo .–Fri., 8 a.m.–6:30 p.m. EST
(excludi g holidays)

2
LIMITED W RR NTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
IMPORT NT PREC UTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
SSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
C BLE DI GR MS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
DJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
TROUBLE-SHOOTING ND M INTEN NCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
WEIGHT RESIST NCE CH RT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
ORDERING REPL CEMENT P RTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
Note: P RT LIST/EXPLODED DR WING and a P RT IDENTIFIC TION CH RT are attached in the center of
this manual. Remove the P RT LIST/EXPLODED DR WING and the P RT IDENTIFIC TION CH RT before
beginning assembly.
TABLE OF CONTENTS
WEIDER is a registered trademark of ICON Health & Fitness, Inc.
ICON OF/DU C N D INC., (ICON), warrants this product to be free from defects in workmanship and mate-
rial, under normal use and service conditions, for a period of one (1) year days from the date of purchase.
This warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to
replacing or repairing, at ICON's option, the product at one of its authorized service centers. ll products for
which warranty claim is made must be received by ICON at one of its authorized service centers with all
freight and other transportation charges prepaid, accompanied by sufficient proof of purchase. ll returns
must be pre-authorized by ICON. This warranty does not extend to any product or damage to a product
caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs not pro-
vided by an ICON authorized service center, to products used for commercial or rental purposes, or to prod-
ucts used as store display models. No other warranty beyond that specifically set forth above is authorized
by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connec-
tion with the use or performance of the product or damages with respect to any economic loss, loss of prop-
erty, loss of revenues or profits, loss of enjoyment or use, costs of removal, installation or other consequen-
tial damages of whatsoever nature. Some provinces do not allow the exclusion or limitation of incidental or
consequential damages. ccordingly, the above limitation may not apply to you. The warranty extended here-
under is in lieu of any and all other warranties and any implied warranties of merchantability or fitness for a
particular purpose is limited in its scope and duration to the terms set forth herein. Some provinces do not
allow limitations on how long an implied warranty lasts. ccordingly, the above limitation may not apply to
you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of mer-
chantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein.
This warranty gives you specific legal rights. You may also have other rights which vary from province to
province or so specified by the retailer of your equipment.
ICON OF/DU CANADA, 900 de l’I dustrie, St-Jérôme, QC J7Y 4B8
LIMITED WARRANTY

3
IMPORTANT PRECAUTIONS
WARNING:To reduce the risk of serious i jury, read the followi g importa t precau-
tio s before usi g the weight system.
1. Read all i structio s i this ma ual a d i
the accompa yi g literature before usi g the
weight system.
2. It is the respo sibility of the ow er to e sure
that all users of the weight system are ade-
quately i formed of all precautio s.
3. The weight system is i te ded for home use
o ly. Do ot use the weight system i a com-
mercial, re tal, or i stitutio al setti g.
4. Use the weight system o ly o a level sur-
face. Cover the floor or carpet be eath the
weight system to protect the floor or carpet.
5. Regularly i spect a d tighte all parts.
Replace a y wor parts immediately.
6. Make sure that the cables remai o the pul-
leys at all times. If the cables bi d while you
are exercisi g, stop immediately a d make
sure that the cables are o all of the pulleys.
7. Keep childre u der the age of 12 a d pets
away from the weight system at all times.
8. Always wear athletic shoes for foot protec-
tio while exercisi g.
9. Keep ha ds a d feet away from movi g parts.
10. Always sta d o the foot plate whe perform-
i g a exercise that could cause the weight
system to tip.
11. If you feel pai or dizzi ess while exercisi g,
stop immediately a d begi cooli g dow .
12. Never release the press arm, butterfly arms,
leg lever, lat bar, or ylo strap while weights
are raised. The weights will fall with great
force.
13. Always disconnect the lat bar or nylon strap
from the weight system when performing an
exercise that does not use the attachments.
14. The war i g decals show below have bee
attached to the weight system i the loca-
tio s show . If a decal is missi g or illegible,
please call our Customer Service Departme t
at the umber o the fro t cover of this ma -
ual to order a free replaceme t decal. Apply
the ew decal i the appropriate locatio .
WARNING:Before begi i g this or a y exercise program, co sult your physicia . This
is especially importa t for perso s over the age of 35 or perso s with pre-existi g health problems.
Read all i structio s before usi g. ICON assumes o respo sibility for perso al i jury or property
damage sustai ed by or through the use of this product.

4
SSEMBLED
DIMENSIONS:
Height: 198 cm
Width: 165 cm
Depth: 86 cm
Low Pulley
Station
Foot Plate
Press rm
Backrest
Curl Pad
djustment
Knob
Butterfly
rms
Weight
Stack
Leg Press
Lever
Thank you for selecting the innovative and versatile
WEIDER®PRO 9930 weight system. The WEIDER®
PRO 9930 offers a unique selection of weight stations
designed to develop every major muscle group of the
body. Whether your goal is to tone your body, build
dramatic muscle size and strength, or improve your
cardiovascular system, the WEIDER®PRO 9930 will
help you to achieve the results you want.
For your be efit, read this ma ual carefully before
usi g the weight system. If you have additional
questions, please contact our Customer Service
Department toll-free at 1-888-936-4266, Mon.–Fri., 8
a.m.–6:30 p.m. EST (excluding holidays). To help us
assist you, please note the product model number and
serial number before calling. The model number is
WESY99300. The serial number can be found on a
decal attached to the weight system (see the front
cover of this manual).
Please use the drawi g below to familiarise your-
self with the major parts of the weight system.
BEFORE YOU BEGIN
Backrest
Seat
High Pulley
Station
Lat Bar

5
ASSEMBLY
Make sure you have the followi g tools:
• Two adjustable wrenches
• One standard screwdriver
• One phillips screwdriver
• One rubber mallet
• You will also need grease or petroleum jelly, a
small amount of soapy water, and clear tape or
masking tape.
Note: ssembly will be more convenient if you have
a socket set, a set of open-end or closed-end
wrenches, or a set of ratchet wrenches.
How to Ide tify Parts
To help you identify the small parts used in assembly,
we have included a P RT IDENTIFIC TION CH RT
in the center of this manual. Place the chart on the
floor and use it to easily identify parts during each
assembly step. Note: Some small parts may have
bee pre-attached. If a part is ot i the parts
bag, check to see if it has bee pre-attached.
How to Orie t Parts
s you assemble the weight system, make sure that
all parts are oriented exactly as shown in the draw-
ings.
Tighte i g Parts
Tighten all parts as you assemble them, unless
instructed to do otherwise.
Questio s?
If you have questions after reading the assembly
instructions, please call our Customer Service
Department at 1-888-936-4266.
Assembly Requires Two Perso s
For your convenience and safety, assemble the
weight system with the help of another person.
Set Aside E ough Time
Due to the many features of the weight system, the
assembly process will require about six hours. By
setting aside plenty of time and by deciding to
make the task enjoyable, assembly will go smoothly.
You may want to assemble the weight system over
a couple of evenings.
Select a Locatio for the Weight System
Because of its weight and size, the weight system
should be assembled in the location where it will be
used. Make sure that there is enough room to walk
around the weight system as you assemble it.
How to U pack the Box
To make assembly as easy as possible, we have
divided the assembly process into four stages. The
parts needed for each stage are found in individual
bags. Importa t: Wait u til you begi each stage
to ope the parts bag for that stage. Place all
parts of the weight system in a cleared area and
remove the packing materials. Do not dispose of
the packing materials until assembly is completed.
Make Assembly Easier for Yourself
Everything in this manual is designed to
ensure that the weight system can be assem-
bled successfully by anyone. Before begi -
i g assembly, make sure to read the
i formatio o this page. This brief i tro-
ductio will save you much more time tha
it takes to read it.
The Four Stages of the Assembly Process
Frame Assembly—You will begin by assembling
the base and the uprights that form the skeleton of
the weight system.
Arm Assembly—During this stage you will
assemble the arms and the leg lever.
Cable Assembly—During this stage you will
attach the cables and pulleys that connect the
arms to the weights.
Seat Assembly—During the final stage you will
assemble the seats and the backrests.

6
1. Before begi i g, make sure that you have read
a d u derstood the i formatio o page 5.
Locate a d ope the parts bag labelled “FRAME
ASSEMBLY.”
Press a 2” Square Inner Cap (38) into the Butterfly
Base (61). Press two 2” Square Inner Caps into the
Press Base (60).
Insert four 5/16” x 2 1/2” Carriage Bolts (1) up
through the indicated holes in the Butterfly Base (61)
and the Press Base (60). Note: If the Bolts fall out,
secure them by putti g a small piece of tape over
the head of each Bolt. Place the Butterfly Base and
the Press Base flat on the floor.
ttach the Press Base (60) to the Butterfly Base (61)
with two 5/16” x 2 3/4” Bolts (20), two 5/16” Flat
Washers (19), and two 5/16” Nylon Locknuts (2).
2. Position the Butterfly Upright (62) as shown. Place
the bracket on the lower end of the Butterfly Upright
over the indicated 5/16” x 2 1/2” Carriage Bolts (1) in
the Butterfly Base (61). Hand tighten two 5/16” Nylon
Locknuts (2) onto the Bolts. Do ot tighte the
Nylo Lock uts yet.
Place the bracket on the lower end of the Press
Frame Upright (59) over the indicated 5/16” x 2 1/2”
Carriage Bolts (1) in the Press Base (60). Hand tight-
en two 5/16” Nylon Locknuts (2) onto the Bolts. Do
ot tighte the Nylo Lock uts yet.
Frame Assembly 1
1
61
38
2
11
19 20
38
60
1
38
2
2
2
11
2
59
62
Position
with the
bracket
on this
side
60
61

7
3. Place two Weight Bumpers (84) over the indicated
holes in the Butterfly Base (61). Slide the Weight
Guides (58) into the indicated holes.
ttach the Weight Guides (58) to the Butterfly Base
(61) with two 3/8” x 2 1/2” Bolts (6), four 3/8” Flat
Washers (17), and two 3/8” Jam Nuts (18).
Slide the eight Weights (8) onto the Weight Guides
(58). Make sure that the Weights are tur ed so the
pi grooves are o the bottoms of the Weights.
4. Press a Weight Tube Bumper (76) into the lower end
of the Weight Tube (77). Slide the Weight Tube into
the center hole in the Weights (8).
Lubricate the holes in the Top Weight (78). Slide the
Top Weight onto the Weight Guides (58).
5. Press two 2” Square Inner Caps (38) into the Butterfly
Top Frame (64). Press two 1” Round Inner Caps (41)
into the top of the Butterfly Top Frame.
ttach the Butterfly Top Frame (64) to the Press Top
Frame (63) with two 5/16” x 2 3/4” Bolts (20), two
5/16” Flat Washers (19), and two 5/16” Nylon
Locknuts (2).
Press a 2” Square Inner Cap (38) into the Press Top
Frame (63).
3
4
17
17
18
17
1884
78
58
8
58
8
61
6
77
76
Lubricate
5
20
63
2
2
38
38
19
19
38
64
Pin
Grooves
41

8
7. Turn the Seat Brace (75) so the nut is on the side
shown. ttach the Seat Brace to the Butterfly Base
(61) with the indicated 5/16” x 2 1/2” Carriage Bolts
(1) and two 5/16” Nylon Locknuts (2). Do ot tighte
the Nylo Lock uts yet.
6. ttach the Butterfly Top Frame (64) and the Press
Top Frame (63) to the indicated brackets on the
Uprights (59, 62) with four 5/16” x 2 3/4” Bolts (20),
two Top Plates (46), and four 5/16” Nylon Locknuts
(2). Note: Before attachi g the Top Frames to the
Uprights, make sure that both Weight Guides (58)
are i side of the i dicated holes. Do ot tighte
the Nylo Lock uts yet.
Secure the Weight Guides (58) to the Butterfly Top
Frame (64) with two 3/8” x 2 1/2” Bolts (6), four 3/8”
Flat Washers (17), and two 3/8” Jam Nuts (18).
8. Hold the Seat Bar (74) between the Seat Brace (75)
and the Butterfly Upright (62) so that the hole that is
closest to a welded plate is toward the Seat Brace.
ttach the Seat Bar to the Seat Brace with two 5/16”
x 2 3/4” Bolts (20), two 5/16” Flat Washers (19), and
two 5/16” Nylon Locknuts (2). Do ot tighte the
Nylo Lock uts yet. Note: Be careful ot to over-
tighte the Nylo Lock uts, or the curl post
attached i step 38 will ot slide freely.
ttach the Seat Bar (74) to the Butterfly Upright (62)
with two 5/16” x 2 3/4” Bolts (20), two 5/16” Flat
Washers (19), and two 5/16” Nylon Locknuts (2).
Tighte all ylo lock uts used i steps 1
through 8.
7
6
75
20
59
58
18
17 17
62
2
2
161
Nut
2
46 46
63
64
17 17
20
6
Holes
62 19
19
75
74 Hole
20
19
220
8

9
11. Press a 1 1/2” Square Inner Cap (79) into the Press
Seat Frame (52).
Slide the bracket on the lower end of the Press Seat
Frame (52) onto the indicated 5/16” x 2 1/2” Carriage
Bolts (1) in the Press Base (60). Tighten two 5/16”
Nylon Locknuts (2) onto the Bolts.
ttach the Press Seat Frame (52) to the Press Frame
Upright (59) with two 5/16” x 2 3/4” Bolts (20), two
5/16” Flat Washers (19), and two 5/16” Nylon
Locknuts (2).
9. Locate a d ope the parts bag labelled “ARM
ASSEMBLY.”
Press a 1” x 7/8” Plastic Bushing (29) onto each weld-
ed spacer on the Press Frame (53). Slide the Press
Frame onto the Press Base (60). (See the inset draw-
ing for proper orientation.) Note: The Plastic
Bushi gs should fit o to the e ds of the tube i
the Press Base. This will be a tight fit.
Lubricate the 3/8” x 8” Bolt (30). ttach the Press
Frame (53) to the Press Base (60) with the Bolt and a
3/8” Nylon Locknut (4). Do ot overtighte the Nylo
Lock ut; the Press Frame must pivot easily.
10. Press a 1 3/4” Square Inner Cap (37) into the top of a
Press rm (54). Press a 1” Inner Cap (80) into the
indicated hole in the Press rm.
ttach the Press rm (54) to the bracket on the Press
Frame (53) with two 5/16” x 2 1/2” Bolts (3) and two
5/16” Nylon Locknuts (2).
Repeat this step to assemble the second Press rm
(54).
Arm Assembly
10
19 22
2
79
52
3
2
53
54
80
37
37
80
59
20
19
60
1
9
30 Lubricate
53
29
60
Tube
4
53
11

14. Ope the parts bag labelled “CABLE ASSEMBLY
AND PULLEYS.” For cable ide tificatio a d routi g
duri g steps 14–32, refer to the CABLE DIAGRAMS
a d CABLE ID CHART o pages 19 a d 20.
Insert two 3/8” x 1” Bolts (15) into the welded brackets
on the Left and Right Butterfly rms (67, 68). Secure
each Bolt with a 3/8” Jam Nut (18).
Ide tify the Short Cable (71). It has a closed loop o
each e d. Slide one end of the Cable onto each of the
3/8” x 1” Bolts (15). Secure the Cable to the Bolts with
3/8” Jam Nuts (18). Do ot overtighte the Jam Nuts.
Remove both 3 1/2” Pulleys (5) from the pre-assembled
djustable Pulley Plates (44). Wrap the Short Cable (71)
around a Pulley in the direction shown. ttach the Pulley
and a Cable Trap (39) to the top hole in the two
djustable Pulley Plates with a 3/8” x 2” Bolt (35) and a
3/8” Nylon Locknut (4). Make sure that the Cable Trap
a d the Pulley Plates are orie ted as show .
12. Press two 1 1/2” Square Inner Caps (79) into the Leg
Lever (49). Insert a Bumper (33) between the brackets
on the Leg Lever. ttach the Bumper to the Leg Lever
with a #10 x 1” Screw (32).
Slide the bracket on the Leg Lever (49) onto the Press
Seat Frame (52). ttach the Leg Lever to the Press Seat
Frame with a 5/16” x 2 1/4” Bolt (81) and a 5/16” Jam
Nut (90). Do ot overtighte the Jam Nut. The Leg
Lever must pivot easily.
ttach a 3/8” x 2 1/2” Eyebolt (83) to the Leg Lever (49)
with a 3/8” Flat Washer (17) and 3/8” Nylon Locknut (4).
13. Press a 1 3/4” Square Inner Cap (37) into each end of
the Right Butterfly rm (68). Wet the lower end of the
rm with soapy water. Slide a 10” Pad (65) onto the
lower end of the rm.
Lubricate the indicated axle on the Butterfly Top Frame
(64). Have a second person slide the Right Butterfly rm
(68) onto the axle, as shown. Refer to the i set draw-
i g. Place two 1” Retai ers (25), with the teeth dow -
ward, o top of a i verted 1” Rou d Cap (26). Usi g
a hammer, tap the 1” Rou d Cap a d the Retai ers
o to the axle to secure the Right Butterfly Arm.
Repeat this step to assemble the Left Butterfly rm (67).
Cable Assembly
90
79
49
79
4
17
83
13
26
68 67
Lubricate
65
81
52
33
32
64
25 37
12
37
14
68
39
44
4
35
67
15
15
5
71
18
Teeth
64
25
26
18
10

11
15. Wrap the Short Cable (71) over a “V” Pulley (21) as
shown. ttach the “V” Pulley and a Long Cable Trap
(14) to one side of the welded bracket on the Butterfly
Upright (62) with a 3/8” x 2 1/2” Bolt (6) and a 3/8”
Nylon Locknut (4).
Wrap the Short Cable (71) over another “V” Pulley
(21), and attach the “V” Pulley and a Long Cable Trap
(14) to the other side of the welded bracket on the
Butterfly Upright (62) in the same manner.
17. Note: It may be helpful to loose the i dicated
5/16” Nylo Lock uts (2) before begi i g this
step.
Wrap the Medium Cable (72) over a 3 1/2” Pulley (5)
as shown. ttach the Pulley and a Cable Trap (39) to
the Press Top Frame (63) with a 3/8” x 3 3/4” Bolt (7).
16. Ide tify the Medium Cable (72). It has a ball o
o e e d a d a threaded shaft o the other. Wrap
the Medium Cable over a 3 1/2” Pulley (5) as shown.
ttach the Pulley to the Press Top Frame (63) with a
3/8” x 3 1/2” Bolt (24), a 3/8” Flat Washer (17), and a
3/8” Jam Nut (18).
Make sure that the Medium Cable (72) is betwee
the 3 1/2” Pulley (5) a d the welded pi o the
Press Top Frame (63).
15
16
62 Welded
Bracket
6
621
21
14
14
4
71
17
72
17 Pin
18
63
5
24
7
72
63
5
39
2
18
36 22
5
72
18. Route the threaded shaft on the Medium Cable (72)
under one of the 3 1/2” Pulleys (5) that are already
mounted in the Double “U”-Bracket (36). Tighten the
3/8” x 1 3/4” Bolt (22).

12
20. ttach the threaded shaft on the Medium Cable (72)
to the Small “U”-Bracket (43) with a 1/4” Flat Washer
(11) and a 1/4” Nylon Locknut (16). Note: See the
i set drawi g. Do ot completely tighte the
Nylo Lock ut; it should be threaded o ly two
tur s o to the e d of the Cable.
ttach the Small “U”-Bracket (43) to the Weight Tube
(77) with a 5/16” x 1 3/4” Bolt (9) and a 5/16” Nylon
Locknut (2).
19. Wrap the Medium Cable (72) over a 4 1/2” Pulley
(34) in the direction shown. ttach the Pulley to the
Butterfly Top Frame (64) with a 3/8” x 1 3/4” Bolt (22)
and a 3/8” Nylon Locknut (4).
21. Ide tify the Lo g Cable (73). It has a ball o o e
e d a d a loop o the other. Route the end with the
loop through the slot in the cable guide on the
Butterfly Base (61).
Route the Long Cable (73) under a 3 1/2” Pulley (5)
as shown. ttach the Pulley and a Cable Trap (39) to
the indicated bracket on the Butterfly Base (61) with a
3/8” x 2” Bolt (35) and a 3/8” Nylon Locknut (4). Make
sure the Cable Trap is orie ted as show .
20
19
4
64
22
72
34
77
72
2
9
21
61
5
73
Cable
Guide
39
4
35
43
11
16 72
43
11 16

13
24. Wrap the Long Cable (73) around a 3 1/2” Pulley (5).
ttach the Pulley and a Cable Trap (39) to the indicat-
ed bracket on the Butterfly Base (61) with a 3/8” x 2”
Bolt (35) and a 3/8” Nylon Locknut (4).
23. Wrap the Long Cable (73) around a 3 1/2” Pulley (5)
in the direction shown. ttach the Pulley and a Cable
Trap (39) to the indicated bracket on the Butterfly
Base (61) with a 3/8” x 2” Bolt (35) and a 3/8” Nylon
Locknut (4).
22. Wrap the Long Cable (73) around a 3 1/2” Pulley (5)
in the direction shown. ttach the Pulley and a Cable
Trap (39) to the Butterfly Upright (62) with a 3/8” x
3 3/4” Bolt (7), a 3/8” Flat Washer (17), and a 3/8”
Nylon Locknut (4). Make sure that the Cable Trap is
orie ted as show .
Wrap the Long Cable (73) over a 3 1/2” Pulley (5) in
the direction shown. Re-attach the Pulley and a Cable
Trap (39) to the lower hole in the djustable Pulley
Plates (44) with a 3/8” x 2” Bolt (35) and a 3/8” Nylon
Locknut (4). Make sure that the Cable Trap is ori-
e ted as show .
24
4
35
39
73
5
61
23
5
73
35
39 61
4
Bracket
Bracket
7
4
44
39
62
17
4
5
5
35
73
39
22

14
26. Wrap the Long Cable (73) around a 3 1/2” Pulley (5)
in the direction shown. ttach the Pulley and a Cable
Trap (39) to the indicated bracket on the Press Base
(60) with a 3/8” x 2” Bolt (35) and a 3/8” Nylon
Locknut (4). Make sure that the Cable Trap is ori-
e ted as show .
27. Wrap the Long Cable (73) around the 3 1/2” Pulley
(5) in the direction shown. ttach the Pulley and a
Cable Trap (39) to the Press Frame Upright (59) with
a 3/8” x 4 3/4” Bolt (23). Ha d tighte a 3/8” Nylon
Locknut (4) two turns onto the Bolt. In step 31, anoth-
er Pulley will be attached to the Bolt.
25. Note: For clarity, this a d the followi g drawi gs
show some parts removed.
Remove the lower 3 1/2” Pulley (5) from the Double
“U”-Bracket (36). Wrap the Long Cable (73) over the
Pulley in the direction shown. ttach the Pulley to the
Double “U”-Bracket with a 3/8” x 1 3/4” Bolt (22) and
a 3/8” Nylon Locknut (4). Make sure that the Double
“U”-Bracket is orie ted as show .
28. Wrap the Long Cable (73) around a 3 1/2” Pulley (5)
in the direction shown. ttach the Pulley and a Cable
Trap (39) to the indicated hole in the Press Frame
(53) with a 3/8” x 3 1/4” Bolt (28), a 3/8” Flat Washer
(17), and a 3/8” Nylon Locknut (4). Make sure that
the Pulley is mou ted o the i side of the Press
Frame a d that the Cable Trap is orie ted as
show .
26
25
36 4
5
73
60
39
4
73
535
22
4
23
73
5
39
59
45
39
73 53 28
17
28
27

15
29. Wrap the Long Cable (73) around a “V” Pulley (21) in
the direction shown. ttach the “V” Pulley and a Long
Cable Trap (14) to the small tube on the Press Seat
Frame (52) with a 3/8” x 3 1/4” Bolt (28), a 3/8” Flat
Washer (17), and a 3/8” Nylon Locknut (4). Note: The
small tube has three adjustme t holes. Mou t the
“V” Pulley i the hole farthest from the Press
Frame Upright (59). Make sure that the Cable Trap
is orie ted as show .
30. Wrap the Long Cable (73) around a 3 1/2” Pulley (5)
in the direction shown. ttach the Pulley and a Cable
Trap (39) to the indicated hole in the Press Frame
(53) with a 3/8” x 3 1/4” Bolt (28), a 3/8” Flat Washer
(17), and a 3/8” Nylon Locknut (4). Make sure that
the Pulley is mou ted o the i side of the Press
Frame a d that the Cable Trap is orie ted as
show .
31. Route the Long Cable (73) around a 3 1/2” Pulley (5)
and back through the opening in the Press Frame
(53).
Remove the 3/8” Nylon Locknut (4) from the 3/8” x
4 3/4” Bolt (23) that was inserted in step 27. ttach
the Pulley and a Cable Trap (39) to the Bolt and
secure them with the Nylon Locknut. Make sure that
the Cable Trap is orie ted as show .
32. Note: Lift the Top Weight (78) o the weight stack
i order to create slack i the Lo g Cable (73)
before begi i g this step.
ttach the Long Cable (73) to the Leg Lever (49) by
slipping the looped end of the Cable onto the looped
end of the 3/8” x 2 1/2” Eyebolt (83).
14
17 4
28
21
5952
73
30
28
53
73 4
5
39
17
29
73
53
5
4
23
39
49
31
32
73
83

16
Seat Assembly
34. Press four 3/4” Round Inner Caps (40) into the ends
of the Pad Tubes (48).
Insert the Pad Tubes (48) into the indicated holes in
the Leg Lever (49) and the Press Seat Frame (52).
Slide Foam Pads (47) onto the ends of both Pad
Tubes.
35. Insert a 1/4” x 2 1/2” Carriage Bolt (12) into the center
hole in a Seat Plate (42). ttach the Seat Plate to the
Press Backrest (89) with two 1/4” x 3/4” Screws (13).
Insert the 1/4” x 2 1/2” Carriage Bolt (12) into the indi-
cated hole in the Press Frame Upright (59) and
secure it with a 1/4” Flat Washer (11) and a 1/4”
Nylon Locknut (16).
Secure the other end of the Press Backrest (89) with a
1/4” x 2 1/2” Screw (10) and a 1/4” Flat Washer (11).
33. Locate a d ope the parts bag labelled “SEAT
ASSEMBLY.”
Insert a 1/4” x 2” Carriage Bolt (85) into the center
hole in a Seat Plate (42). ttach the Seat Plate to a
Seat (51) with two 1/4” x 3/4” Screws (13).
Insert the 1/4” x 2” Carriage Bolt (85) into the indicat-
ed hole in the Press Seat Frame (52) and secure it
with a 1/4” Flat Washer (11) and a 1/4” Nylon Locknut
(16). Secure the other end of the Seat (51) with a 1/4”
x 2” Bolt (86) and a 1/4” Flat Washer.
51
52
11
11
16
86 13
42
85
35 10
11
11
16 59
13 42
12
89
33
34
40
49
52 47
47
40
48

17
36. Insert a 1/4” x 1 1/2” Carriage Bolt (82) into the center
hole in a Seat Plate (42). ttach the Seat Plate to a
Seat (51) with two 1/4” x 3/4” Screws (13).
Insert the 1/4” x 1 1/2” Carriage Bolt (82) into the indi-
cated hole in the Seat Bar (74) and secure it with a
1/4” Flat Washer (11) and a 1/4” Nylon Locknut (16).
Secure the other end of the Seat (51) with a 1/4” x
1 1/2” Screw (88) and a 1/4” Flat Washer.
37. ttach the Backrest (66) to the Butterfly Upright (62)
with two 1/4” x 2 1/2” Screws (10) and two 1/4” Flat
Washers (11).
38. ttach the Curl Pad (69) to the Curl Post (70) with two
1/4” x 3/4” Screws (13).
Insert the Curl Post (70) into the Seat Brace (75) and
secure the Curl Post at the desired height with the
djustment Knob (45).
37
66 62
10
11
11
38
70
69
45
75
13
36 51
1188
16
82 42 74
13

18
39. pply the WEIDER PRO 9930 decal in the location
shown.
40. Make sure that all parts have been properly tightened. The use of the remaining parts will be explained in
DJUSTMENT, beginning on page 21 of this manual.
Before using the weight system, pull each cable a few times to make sure that the cables move smoothly
over the pulleys. If one of the cables does not move smoothly, find and correct the problem. IMPORTANT: If
the cables are ot properly i stalled, they may be damaged whe heavy weight is used. See the
CABLE DIAGRAMS o pages 19 a d 20 of this ma ual for proper cable routi g. If there is a y slack
i the cables, you will eed to remove the slack by tighte i g the cables. See TROUBLE-SHOOTING
AND MAINTENANCE o page 22.
39
WEIDER
PRO 9930

19
CABLE DIAGRAMS
The cable diagrams below and on the next page show the proper routing of the Short Cable (71), the Medium
Cable (72), and the Long Cable (73). The numbers show the correct route for each Cable. Make sure that the
Cables are routed correctly, that the Pulleys move smoothly, a d that the Cable Traps do ot touch or
bi d the Cables. I correct cable routi g ca damage the weight system.
Cable ID Chart
(73) 7.6m (24 ft. 11 in.)
(72) 3.5m (11 ft. 6 in.)
(71) 1.9m (6 ft. 3 in.)
Short Cable (71)
3
4
5
1
2
1
3
4
5
2
Medium Cable (72)

20
Lo g Cable (73)
12
3
4
5
6
7
8
9
13
11
12
10