Bodyworx L700015 User manual

Home Gym
Model No:
BODYWORX
BODYWORX
1
Retain this owner’s manual for future reference
Read and follow all instructions in this owner’s manual
Version A
L700015

2
PART LIST
PART NO. DESCRIPTION QUANTITY
1 MAIN BASE 1
2 GUIDE ROD 2
3 BACK BASE 1
4 LEFT AND RIGHT BASE 2
5 SELECTOR SHAFT 1
6 TOP PLATE 1
7 WEIGHT STACK 9
9 RUBBER DOUNT 2
10 VERTICAL BEAM 1
11 SEAT SUPPORTER 1
12 TOP CROSS BEAM 1
13 STEEL PLATE 2
14 LEG EXTENSION / ARM CURL BAR 1
15 PRESS BAR 1
16 LEFT PEC DECK ARM 1
17 RIGHT PEC DECK ARM 1
18 PRESS PIN 1
19 SEAT 1
20 BACK SEAT 1
21 PULLEY BLOCK 2
22 FLOATING PULLEY BLOCK (A) 1
23 FLOATING PULLEY BLOCK (B) 1
24 CABLE 2350 mm 1
25 CABLE 3850 mm 1
26 CABLE 2760 mm 1
27 CHAIN ( LONG & SHORT ) 2
28 PEC DECK PAD 2
29 FOAM 4
30 LAT BAR 1
31 CURL BAR 1
32 PAD HOLDER 2
33 PULLEY 12
35 CHAIN HOOK 4
36 HAND GRIPS 127 mm 8
37 RUBBER BUMPER 1
38 1" ROUND PLASTIC BUSHING FOR WEIGHT STACK 1
39 PLASTIC BUSHING 6

3
PART LIST
PART NO. DESCRIPTION QUANTITY
40 1"ROUND END CAP 4
41 2"SQUARE END CAP 12
42 RUBBER END CAP 2
43 HANDLE PIPE 2
44 PIN FOR WEIGHT STACK 1
45 1-1/2"SQUARE END CAP 2
46 PRESS BAR SHAFT 1
47 QUICK PIN FOR WEIGHT STACK 1
48 HEX BOLT M10 x 45mm 9
49 HEX BOLT M12 x 80mm 1
51 NUTS M10mm 2
52 HEX BOLT M8 x 45mm 1
53 HEX BOLT M10 x 70mm 13
54 HEX BOLT M10 x 25mm 6
55 POP-PIN 1
56 HEX BOLT M10 x 65mm 3
57 HEX BOLT M8 x 65mm 4
58 WASHER OD 48MM*1D13MM 1
60 NYLONNUTS M12mm 1
61 NYLON NUTS M16mm 4
63 NYLON NUTS M10mm 27
64 NYLON NUTS M8mm 1
65 WASHER φ16 4
66 WASHER φ12 2
68 WASHER φ10 60
69 M8 WASHER 6
70 RUBBER CAP 2
71 METAL OIL BUSHING 8
72 BUSHING 50 x 45mm 1
73 RUBBER CAP 38 x 34mm 2
74 TOOL 2
75 ANKLE STRAPE 1
76 HEX BOLT M10 x 35mm 2
77 SEAT ADJUSTMENT TUBE 1

4

5
13

6
STEP 01
1. PLACE RUBBER CAP (42) INTO BOTH ENDS OF BACK BASE (03).
2. ATTACH BACK BASE (03) TO MAIN BASE (01). FASTEN TIGHTLY BY BOLT (53) AND
WASHER (68). INSERT 2 GUIDE RODS (02) TO THE RIGHT AND LEFT HOLE OF BACK
BASE (03). FASTEN TIGHTLY BY BOLT (54) AND WASHER (68).
3. ATTACH VERTICAL BEAM (10) TO MAIN BASE (01). FASTEN TIGHTLY BY BOLT (53).
WASHER (68) AND NYLON NUTS (63).

7
STEP 02
1. PUT THE RUBBER DOUNT (09) INTO THE GUIDE ROD (02).
2. SLIDE THE WEIGHT PLATE (07) AND TOP PLATE (06) THROUGH GUIDE ROD (02).
CHOOSE THE PROPER WEIGHT AND INSERT THE PIN FOR WEIGHT STACK (44)
INTO THE GROOVE OFWEIGHT STACK (07).
3. INSTALL 1" ROUND BUSHING (38) INTO THE SELECTOR SHAFT (05) WITH QUICK
PIN (47) THEN ATTACH THE SELECTOR SHAFT (05) INTO THE CENTER HOLE OF TOP
PLATE (06).
4. PLACE 2" SQUARE CAP (41) INTO THE ENDS OF MAIN BASE (01).
5. PLACE RUBBER CAP (70) INTO BOTH ENDS OF RIGHT AND LEFT BASE (04).
6. ATTACH RIGHT AND LEFT BASE (04) TO MAIN BASE (01). FASTEN TIGHTLY BY
BOLTS(53) WASHERS(68) AND NYLON NUTS(63).
53

8
STEP 03
1. PUT 2” SQUARE END CAP(41) INTO BOTH SIDES OF TOP CROSS BEAM(12).
2. ATTACH TOP CROSS BEAM (12) ONTO THE VERTICAL BEAM (10) AND FIX TIGHTLY
BY BOLTS(53) WASHER(68) AND NYLON NUTS(63). INSERT THE TOP SIDE OF GUIDE
RODS (02) INTO THE HOLE OF TOP CROSS BEAM(12). FASTEN TIGHTLY BY BOLTS
(54) AND WASHERS (68).
3. SCREW THE RUBBER BUMPER (37) TO THE VERTICAL BEAM (10).
4. ATTACH 2 PULLEY BLOCK (21) TO THE BOTH SIDES OF THE VERTICAL BEAM (10).
AND FIX TIGHTLY BY BOLTS (56) WASHERS(68) AND NYLON NUTS (63).
5. INSTALL PRESS PIN TO THE VERTICAL BEAM (10). FIX TIGHTLY BY BOLTS (52)
WASHER (69) AND NYLON NUTS (64).

9
STEP 04
1. PUT 2” SQUARE END CAP(41) INTO BOTH SIDES OF LEG EXTENSIONS / ARM CURL
BAR(14) AND SEAT ADJUSTMENT TUBE (77). ATTACH BOTH SIDE OF SEAT
SUPPORTER(11) TO THE VERTICAL BEAM(10) AND LEG EXTENSION/ARM CURL
BAR(14) RESPECTIVELY. FASTEN TIGHTLY BY BOLTS(53)/WASHER(68)/NYLON
NUTS(63) AND BOLTS(49)/WASHER(66)/NYLON NUTS(60).
2. INSERT THE VERTICAL TUBE OF SEAT ADJUSTMENT TUBE(77) INTO THE
VERTICAL TUBE(77) OF SEAT SUPPORTER(11) SELECT THE PROPER HEIGHT
POSITION AND FIX TIGHTLY BY POP-PIN(55).
3. ATTACH BACK SEAT(20) TO VERTICAL BEAM(10) AND ATTACH SEAT(19) TO SEAT
ADJUSTMENT TUBE(77) FIX TIGHTLY BY BOLTS(57), WASHER(69) RESPECTIVELY.
4. SLIDE ONE PAD HOLDER(32) THROUGH THE HOLE OF LEG EXTENSION/ARM CURL
BAR(14) AND THE OTHER ONE PAD HOLDER(32) THROUGH THE HOLE OF SEAT
ADJUSTMNET TUBE (77).
5. ATTACH FOAM(29) ONTO BOTH SIDES OF THE PAD HOLDER(32).
6. PUT 1” ROUND END CAP(40) INTO BOTH SIDES OF THE PAD HOLDER(32).
7. SCREWING RUBBER BUMPER(37) TO SEAT SUPPORTER (11) TIGHTLY.

10
STEP 05
1. PUT 2” SQUARE END CAP (41) INTO PRESS BAR (15).
2. ATTACH METAL OIL BUSHING (71) TO THE UPPER AND LOWER HOLES OF THE
PRESS BAR(15) RESPECTIVELY.
STEP 06
1. ATTACH PRESS BAR (15) TO TOP CROSS BEAM(12) WITH PRESS BAR SHAFT(46) AND
METAL OIL BUSHING(71), WASHER(65) AND NYLON NUTS(61).
2. INSTALL RIGHT AND LEFT PEC DECK ARM (17&16) TO PRESS BAR(15). FIX TIGHTLY
BY WASHER(65) AND NYLON NUTS(61).
3. SLIDE PEC DECK PADS(28) ONTO RIGHT AND LEFT PEC DECK ARM (17&16).
4. ATTACH HANDLE PIPE(43) AND HAND GRIP(36) TO RIGHT AND LEFT PEC DECK
ARM(17&16) RESPECTIVELY. FIX TIGHTLY BY BOLTS(54) AND WASHER(68).
5. PUT RUBBER CAP(73) AND HAND GRIPS (36) INTO THE LOWER PART OF RIGHT AND
LEFT PEC DECK ARM (17&16).

11
STEP 07
INSTALL CABLE (24) (25) (26) AND PULLEY (33)
PLEASE PUT THE CABLE, BOLT, WASHER, NUT STEP BY STEP AS FOLLOWING PICTURE SHOWED.
CABLE 24 : FROM (24-1) TO (24-5)
CABLE 25 : FROM (25-1) TO (25-6)
CABLE 26 : FROM (26-1) TO (26-5)
24-1 24-2
24-3
25-5
24-4
24-5
25-3
25-2
25-1
25-4 25-6

12
STEP 08
1. SLIDE THE HAND GRIP (36) INTO THE LAT BAR (30) ON BOTH SIDE,
THEN CONNECT THE LAT BAR (30) AND CABLE (26) WITH HOOK (35).
2. SLIDE THE HAND GRIP 127mm (36) INTO THE CURL BAR (31) ON BOTH SIDE,
THEN CONNECT THE CURL BAR (31) AND CHAIN (SHORT) (27) TO THE CABLE
(25) WITH HOOK (35).
26-5 26-1 26-2
26-326-4

13
24-1
24-2
24-3
24-4
25-5
24-5
25-1
25-2
25-3
25-4
25-6
26-1
26-3
26-2
26-5
26-4

BODYWORX
BODYWORX