Bogen Quantum wbs810qip User manual

Speaker Layout

HALLWAY - Wall baffle speakers work well with rooms and

hallways that are 20’ to 60’ wide. Layout starts at one

end of the hallway or room. The first speaker should be

installed 10’ from the end of the hallway or room. The next

speaker on that wall should be installed 20’ from the first

speaker. Each additional speaker should be installed 20’

apart from the previous one.

The first speaker on the opposing wall should be installed

20’ from the end of the hallway or room, thereby

staggering the speakers. Each additional speaker should

be installed 20’ apart from the previous one

(see Figure 1)

CLASSROOM -

In most cases, a classroom environment

requires only a single wall baffle speaker to service the

entire room. The final placement of the speaker within the

classroom can vary, but common area locations such as

at the head of the class or near the room entrance are

typically chosen

(see Figure 2).

Based on the speaker position that has been selected, and

using the supplied hardware, the installer can choose

between several mounting options

(see Figures 3-6).

The layout of the speakers should be planned prior to installation. Because wall baffle speakers are designed to

project forward, it is best to aim them in the same direction, as this provides for both greater coverage and clarity.

You can use the building’s roof pillars or other available supports for mounting the wall baffles.

In some cases, it may be necessary to mount the wall baffles on opposing walls. In these cases, the speakers will

project sound in opposing directions.

VoIP Wall Baffle Speaker

Model WBS810QIP

Specifications subject to change without notice.

740-00001A 1704

www.bogenedu.com

20’ to 60’

10’

20’

WALL

START

Figure 1

Figure 2

Installation Manual

HALLWAY

)))))

)))))CLASSROOM

SPEAKER

Speaker Installation

SIDE

VIEW

Figure 3 Figure 4

2x2 Wall Mount Box Mount

SIDE

VIEW

Figure 5 Figure 6

Tilted Mount

Corner Mount

STEP 1 -Select the mounting option from

Figures 3 – 6

and use the supplied hardware for ganged box

mount or wall mount with anchors.

NOTE:

Wall baffle speakers should be installed between 8 and 16 feet from the floor depending upon need.

Speaker Assembly

When the WBS810QIP is used with a CA15 Call

Switch, make the connection to the Quantum VoIP

Module CALL SWITCH connector as shown in

Figure 10; the RED wire connects to the “T” pin

and the BLACK wire to the “R” pin using the included

3-Pin Dinkle wire terminal connector.

NOTE:

LINE OUT Connector -This function is reserved

for future use.

Figure 8

Figure 7

Figure 9

SIDE

VIEW

3/4 REAR

VIEW

FRONT

TOP

BOTTOM

Speaker Connection

Additional Accessories

NOTE:

Please refer to the Quantum Multicom IP

“VoIP Speakers Configuration and Operations

Manual” for detailed instructions on how to con-

figure these speakers in the system.

STEP 2 -Using shielded Category 5 or higher Ethernet cable

is recommended. If it is not available, add the clamp-on

ferrite bead that is located in the installation kit to the

Ethernet cable and secure it with the wire tie to the

speaker cage (Figure 7).

The power is supplied by PoE using an 802.3af com-

pliant network switch or PoE injector.

STEP 3 -To assemble the Wall Baffle Speaker (Figure 8),

first align the two “notches” (A) located at the

top of the speaker baffle with the “notches” (B)

at the top of the rear housing. Then, rotate the

speaker baffle downward (Figure 9) until the

two bottom sections (C & D) snap together.

PRESS

TO CALL

CA15

PRESS TO CALL

VoIP MODULE

3-Pin

Dinkle

Figure 10

Wire

Tie

RJ45

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part

15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful interference; in which case,

the user will be required to correct the interference at his own expense.

www.bogen.com

The WBS810QIP is warranted to be free from defects in material or workmanship for three (3) years from the date of sale to the original purchaser.

Any part of the product covered by this warranty that, with normal installation and use, becomes defective will be repaired or replaced by Bogen, at our

option, provided the product is shipped insured and prepaid to: Bogen Factory Service Department: 4570 Shelby Air Drive, Suite 11, Memphis, TN 38118,

USA. The product(s) will be returned to you freight prepaid. This warranty does not extend to any of our products that have been subjected to abuse, mis-

use, improper storage, neglect, accident, improper installation or have been modified or repaired or altered in any manner whatsoever, or where the

serial number or date code has been removed or defaced.

THE FOREGOING LIMITED WARRANTY IS BOGEN'S SOLE AND EXCLUSIVE WARRANTY AND THE PURCHASER'S SOLE AND EXCLUSIVE

REMEDY. BOGEN MAKES NO OTHER WARRANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED, AND ALL IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED AND EXCLUDED TO THE MAXIMUM EXTENT

ALLOWABLE BY LAW. Bogen's liability arising out of the manufacture, sale or supplying of products or their use or disposition, whether based upon

warranty, contract, tort or otherwise, shall be limited to the price of the product. IN NO EVENT SHALL BOGEN BE LIABLE FOR SPECIAL, INCIDENTAL

OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, LOSS OF PROFITS, LOSS OF DATA OR LOSS OF USE DAMAGES)

ARISING OUT OF THE MANUFACTURE, SALE OR SUPPLYING OF PRODUCTS, EVEN IF BOGEN HAS BEEN ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES OR LOSSES. Some States do not allow the exclusion of limitation of incidental or consequential damages, so the above limitation

or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from State to State.

Products that are out of warranty will also be repaired by the Bogen Factory Service Department -- same address as above or call 201-934-8500. The parts

and labor involved in these repairs are warranted for 90 days when repaired by the Bogen Factory Service Department. All shipping charges in addition to