Bolin Technology EX1000 Series User manual

1
Dual Output SDI+IP
FHD PTZ Camera
USER MANUAL
Part Two: IP Network Camera User Manual
(For EX1000/SD500 Series)
Version: SN-IP-M-EX/SD-02232022
© 2022 Bolin Technology

2
Contents
USER QUICK NOTICE GUIDE ...................................................................................................................................................... 3
NETWORK CONNECTION .......................................................................................................................................................... 6
LOGIN PREPARATION.......................................................................................................................................................................... 6
CHECK BEFORE LOGIN ......................................................................................................................................................................... 6
LOGGING IN TO THE WEB INTERFACE ....................................................................................................................................... 7
NOTE: FORGOT PASSWORD?.............................................................................................................................................................. 7
IP SEARCH TOOL: .............................................................................................................................................................................. 7
INTRODUCTION TO THE WEB INTERFACE.................................................................................................................................. 8
LIVE VIEW ........................................................................................................................................................................................ 8
HOME POSITION: .............................................................................................................................................................................. 9
PAN /TILT ....................................................................................................................................................................................... 9
PTZ SETTING .................................................................................................................................................................................... 9
SCANNING:..................................................................................................................................................................................... 10
FAST SETTING ................................................................................................................................................................................. 10
CONFIGURING THE CAMERA FROM THE MENU BAR............................................................................................................... 11
CAMERA-CAMERA SETTING-VIDEO ..................................................................................................................................................... 11
CAMERA-CAMERA SETTING-CODEC..................................................................................................................................................... 11
TRUE DUAL OUTPUT VIDEO FORMAT SETTING........................................................................................................................................ 12
CAMERA-CAMERA SETTING-SNAPSHOOT ............................................................................................................................................. 13
CAMERA-CAMERA SETTING-OSD....................................................................................................................................................... 13
CAMERA-CAMERA SETTING-PRIVACY MASK......................................................................................................................................... 14
CAMERA-CAMERA SETTING-PRESET CMD........................................................................................................................................... 15
AUDIO-AUDIO SETTINGS................................................................................................................................................................... 16
NETWORK-NETWORK SETTING-NETWORK............................................................................................................................................ 16
NETWORK-NETWORK SETTING-PORT .................................................................................................................................................. 16
NETWORK-NETWORK SETTING-RTMP ................................................................................................................................................ 17
NETWORK-NETWORK SETTING-SRT.................................................................................................................................................... 18
NETWORK-NETWORK SETTING-FTP.................................................................................................................................................... 19
.................................................................................................................................................................................................... 19
NETWORK-NETWORK SETTING-MULTICAST.......................................................................................................................................... 19
SYSTEM-SYSTEM SETTING-DEVICE...................................................................................................................................................... 20
SYSTEM-SYSTEM SETTING-TIME ......................................................................................................................................................... 20
SYSTEM-SYSTEM SETTINGS-MAINTENANCE .......................................................................................................................................... 21
SYSTEM-SYSTEM SETTING-USER......................................................................................................................................................... 21
SYSTEM-SYSTEM SETTING-ONLINE USER.............................................................................................................................................. 22
LOCAL-STORAGE SETTING-PLAY SETTING.............................................................................................................................................. 22
LOCAL-STORAGE SETTING-STORAGE SETTING........................................................................................................................................ 23
OPERATION LOG.............................................................................................................................................................................. 23
FIRMWARE UPGRADE............................................................................................................................................................. 24
UPGRADING MCU FIRMWARE........................................................................................................................................................... 24
UPGRADING IP ENCODER FIRMWARE................................................................................................................................................... 24

3
Bolin FHD Dual Output PTZ camera IP web interface
User Quick Notice Guide
This Quick Guide is for Bolin FHD Dual Output PTZ camera IP web interface use. Please read it carefully before you start using
your camera and follow the instruction to properly use the camera, or check it when you are having some trouble with IP video
streaming and IP control.
Please contact Bolin technical support team at www.bolintechnology.com if you have more questions or having trouble that is not
included in this guidance.
Note:
•Supports Edge, Chrome, Firefox and Safari. Internet Explorer 11 browser.
•When using Internet Explorer 11 browser.
oIt will be required to download the Controls (VideoPlugin) for the first-time login when using Internet
Explorer, please click the download link and follow the prompts to download and install it.
oAfter the VideoPlugin has been installed, you may be prompted to update the VideoPlugin, please
uninstall the old version of Plugin before you download and install the new version of Plugin
•When using Edge, Chrome, Firefox and Safari etc, non-IE browsers,
oHTML5 is supported.
oVideo Plugin is not needed.
oSome of the features are limited, like Privacy Mask, Live View page’s Record, Capture, and other function
icons.
oLive view latency may be 1-2 seconds longer than IE browser.
In this User Guide, illustration drawings and screen captures are taken from SD500 camera’s IP Web Interface, other
applicable cameras have the same software. This User Guide can be also used for Bolin’s EX1000 series PTZ cameras.
Login
The default static IP address of the camera is
192.168.0.13, and default subnet mask is 255.255.255.0.
Please change your PC/laptop’s IP address to be located
within the same subnet as the camera.
The login procedure as following:
•Open the browser, running it as Administrator
•Enter the login page by typing: http://192.168.0.13
•By default, Username: admin, Password: admin
•The IP camera supports strong password
function, it requires to change the password for
the first-time login
NOTE: If the camera IP address has been modified, the
login page URL should be http://x.x.x.x (x.x.x.x is the
correct IP address of the camera)
Hardware Decoding
The camera supports FHD resolution on both HDMI/SDI and IP interface, it may consume more hardware performance of the
PC/laptop when using the IP interface.
Hardware decoding supports Adaptation, CPU, Intel and Nvidia mode.
•Adaptation mode (default), a better strategy for decoding based on the PC/laptop hardware configuration will be
automatically selected by system.
•CPU mode, using CPU to do decoding, it will consume a lot of CPU resources, only select it if there is no independent
graphics card or the graphics card is poor.

4
•Intel mode, using the Intel graphics
card to do decoding, select this mode if
your PC/laptop graphics card is Intel.
•Nvidia mode, using Nvidia graphics
card to do decoding, select this mode if
your PC/laptop graphics card is Nvidia.
NOTE: The Default is Adaptation mode, and the
decoding strategy is automatically selected by
the system, if is it not satisfied, please select the
actual graphics card to do decoding according to
your PC/laptop hardware configuration. Or select
the CPU mode if your PC/laptop without
independent graphics card.
For more stable usage, the PC/laptop that equipped Intel or Nvidia independent graphics card are recommended.
IP Firmware Update
The firmware update including two steps:
•The First step is to select the firmware file and upload it to the camera IP module, this step will be fast.
•The Second step is the firmware burning and updating, there will be a percentage progress bar display to indicate the
burning and updating status on the page.
•the burning and updating process takes about 3 minutes, after the update is successful, the page will prompt “Upgrade is
successful…”, please click OK button to reboot the camera.
•Please don’t power off or reboot the camera during the whole updating process, until the page prompt “Upgrade is
successful…”
Codec Setting
Video Compression supports H.264, H.265 and MJPG.
If video compression been selected MJPG mode, it will not support RTSP streaming features. For a better experience, it is
recommended to choose the H.264 or H.265 encoding.
IP Interface Reboot
The reboot action executed from IP interface will cause the camera go back to home position, but will not interrupt the HDMI/SDI
output.
Audio Input
Audio Compression supports AAC, G.711a and G.711u.
Bit Rate adjustable from 32K, 48K, 96K and 128K when in AAC mode
Sampling Rate adjustable from 32K, 44.1K and 48K when in AAC mode
NOTE:
•Bit rate is fixed as 64K and Sampling rate fixed as 8K when Audio
Compression is set to G.711a and G.711u mode
•If audio compression been changed, you have to close the browser and re-
login, otherwise, there will have noise of the audio output.

5
IP Video Format
IP video resolution and SDI/HDMI video resolution are bounded to PAL/NTSC format.
e.g. if SDI/HDMI video is set to 1080p60 resolution, then IP video can only be selected
under the PAL format resolution, such as 1080p60, 1080p30, 720p60 and 720p30, etc.
At this moment, the IP video cannot be selected 1080p50, 1080p25 and 720p50, etc.
NOTE: According to the SDI/HDMI video resolution that has been set to, the IP
resolution will only have available resolution displayed for you to select.
Video Stream Connection
For RTSP:
Connection String: rtsp://<IP address>:<RTSP port>/PSIA/Streaming/channels/0 <0 / 1>
By default, IP address is 192.168.0.13, RTSP port is 554
Channels/0 indicates the main stream, channels/1 indicates the sub stream
To receive RTSP for main stream: rtsp://192.168.0.13:554/PSIA/Streaming/channels/0
To receive RTSP for sub stream: rtsp://192.168.0.13:554/PSIA/Streaming/channels/1
NOTE: *Do not include brackets < > in connection URL strings
For Multicast
Connection String: udp://@<multicast IP address>:<multicast port>
Multicast IP address and port can be configured on camera IP web interface>Network>Multicast page
For example, if set multicast IP address to 224.5.6.7, set multicast port to 9000
To receive multicast stream: udp://@224.5.6.7:9000
Note: *Do not include brackets < > in connection URL strings
User can configure multicast IP address and port for Main stream, Second stream and Third stream separately.
For RTMP
This camera supports RTMP protocol, can push RTMP streaming to others video streaming platform, e.g. YouTube etc.
Connection String: RTMP stream URL/key
NOTE: User needs to login to the YouTube platform, get the RTMP stream URL and key, and then configure it to the RTMP
setting page of the camera’s IP web interface.
For VMS Connection
When you use VMS (such as exacqVision) to connect the camera via ONVIF
protocol, you must to include the port 2000 for VMS connection.
For example: if the camera IP address is 192.168.0.13, you need to enter
192.168.0.13:2000 on VMS configuration menu.

6
Part Two: Network Camera User Manual
Network Connection
Before accessing a network camera (also known as IP Camera or IPC) from a PC, you need to connect the
network camera to the PC directly with a network cable or via a switch or router.
Use a Shielded Twisted Pair (STP) cable to connect the network interfaces of the network camera and the PC.
Use Shielded Twisted Pair (STP) cables to connect the network interfaces of the camera and the switch or router.
Login Preparation
After you have completed the installation in accordance with the quick guide, connect the camera to power to boot
it. After the camera is booted, you can access the camera from a PC client using or a Video Management System
(VMS).
Browser Edge, Chrome, Firefox and Safari, Internet Explorer 11 browser is supported
The following uses Internet Explorer 11 on a Microsoft Windows 10 operating system as an example.
Check before login
⚫ The camera is powered on and connected to the network switch
⚫ The camera’s IP address is located within the same subnet as the PC
⚫ The PC is connected to the network switch
⚫ The PC’s IP address is located within the same subnet as the camera
⚫ The PC is installed with Browser (Edge, Chrome, Firefox, Safari and Internet Explorer 11)
⚫ Use default video format setting or set the camera video format to 1080P30 or 1080P25 using RS485 keyboard
(Refer to camera setting menu).

7
Logging in to the Web Interface
The default static IP address of the camera is 192.168.0.13, and the default subnet mask is 255.255.255.0
The following uses Internet Explorer as an example to describe the login procedure.
1. Browse to the login page by entering correct IP address (e.g. http://192.168.0.13 ) of your camera in the Internet
Explorer address bar.
2. The default username admin and password admin
3. The camera supports strong password function, it
requires to change the password to activate the camera
for the first-time login
4. If this is your first timing login in to the camera web
interface, you have to download and install the
Control plug-in, click “Click Here To Download
Controls” link to start the download.
5. Follow system prompts and install the “VideoPlugin-
win32-4.1.0.10541”. You need to close your browser
and reopen it again to complete the installation.
6. Click Allow to enable the plugin when you re-login
after installed the “VideoPlugin-win32-4.1.0.10541”
7. When using Edge, Chrome, Firefox and Safari etc. non-IE browses;
•HTML5 is supported
•Video plugin is not needed
•The default password is used for your first login. To ensure account security, please change the password after
your first login. You are recommended to set a strong password (no less than eightcharacters).
•VideoPlugin version may different in different camera version.
•If you login with Remember Password selected, you do not need to enter the password each time when you login,
to ensure security, you are not advised to select Remember Password.
NOTE: Forgot Password?
•A message will pop up, which
reads: “Please contact the
manufacturer for disposal!”
•You can download the IPCSearch
tool from the
www.bolintechnology.com
•Unzip the file and configure your
laptop in the same subnet as
camera’s, run the IPCSearch tool
and you will get the camera
connection with your IPCSearch
tool, click this camera bar (not to
tick off the selection box) in the list,
and then click Forgot Password
button which is in the bottom right
corner, a key number will display in the pop-up window
•Please copy this key number and send it to us, you can contact us at: [e-mail]
•A BOLIN Technology Support team will provide a temporary password that is only valid for 24 hours, which can
be used to log in to the camera to create a new password. Please use the temporary password within 24 hours,
you will have to repeat the above process to get a new temporary password if it gets expired.
NOTE: Please DO NOT power off the camera until use the temporary password for login to change the password,
otherwise, the temporary password provided based on the Key number will be invalid.
IP Search Tool:
•Running the IP Finder Tool on your laptop/pc, it will automatically get the list of all cameras that located in the
same network.
•You can get the MAC address, IP address, Camera name, Camera model, Serial number etc. of the cameras.
•IP Finder Tool will help you to get the IP address when you forget the camera IP.

8
Introduction to the Web Interface
After login to the web interface, you will locate at Live View page, there are three functional modules, as followings:
1. Menu Bar
•Used to navigate between Live View, Fast Setting, Camera, Audio, Network, System, Local, Operation, as
well as Log Out
2. Live View Panel
•Used to select the way how the live stream is viewed
•Used to switch between Main, Sub and 3rd Stream, as well as access / playback recorded files
•Contains Record, Capture, Speaker, Mic, Enlarge, Shrink and Full Screen buttons
•Contains Preset CMD, Camera Menu setting interface, where optional features can be configured
3. Camera Control Panel
•Used for home position
•Used for camera PTZ control, presets setting and recall
•Used to create Patrol, Scanning, Power On Action etc.
Live View
This setting page is to have the camera live preview, playback the recorded video files, also supports quick access
recording, screenshot, full screen etc.
Main Stream:
The main video stream, viewed by default
on the live view panel, the main stream
parameters can be configured on
Camera>Codec page
Sub Stream:
The sub video stream, you can click Sub
Stream button to switch to watch the sub
video stream on live view panel, the stream
parameters can be configured on
Camera>Codec page
3rd Stream:
The 3rd video stream, you can click 3rd Stream button to switch to watch 3rd stream on live view panel, the 3rd stream
parameters also can be configured on Camera>Codec page.
The quick access buttons on the lower left corner of the live view panel from 1 to 7 is Record, Video Capture (take a
screenshot), Speaker, Mic, Enlarge, Shrink, Full Screen.
Record: supports insert Micro SD card to the camera, to do record and save video in the SD card;

9
Capture: to take a screenshot of the camera video image;
Speaker: to turn on / off the preview audio on live view panel;
Mic: to enable/disable the Mic which built-in the camera;
Enlarge: to enlarge the camera preview image.
Click the Enlarge button, the button color will turn yellow, then you can click the preview image to zoom in, it supports
for zooming in by 3 times;
Shrink: to shrink the camera preview image.
After the preview image has been zoomed in by 3 times, you can click the Shrink button to start zooming out. The
function will available when this button been clicked and turn to yellow color, it supports for zooming out by 3 times;
Full Screen: to get full screen view of the camera image;
NOTE: Feature icons 1-7 are not supported in non-IE browsers, and these icons will not to be displayed in the interface
Home Position:
•The first position where the camera will be in after
initializing(rebooting)
•Once presets have been set up, one of the presets can be selected as
the Home Position. (set preset 1 as the Home Position usually)
Pan / Tilt
•Use the arrow button to control the camera.
•Pan/Tilt: pan and tilt, speed can be set from 1 to 8 by drag the
Pan/Tilt Speed setting bar
•Zoom: zoom in and zoom out, zoom speed can be set from 1 to 8 by
drag the Zoom Speed setting bar.
•Focus: supports Auto and Manual mode, focus speed can be set from
1 to 8 by drag the Focus Speed setting bar
PTZ Setting
This menu contains the section where the Auto Scanning, Preset, Patrol, Scanning, Power On Action, Cruise can be
configured.
Auto Scanning:
Camera image (pan) can be set to move horizontally from left to right or from
right to left continuously.
Moving speed can be programmed, speed level from 1-8 adjustable.
Preset:
Presets are predetermined positions that the user can recall the camera to recall
quickly, supports 255 presets at maximum.
To add a new preset:
1. Select Preset in the PTZ Setting bar.
2. Click Create button, it will extend preset number and name field.
3. Select a preset number and create a preset name, or just by default name
preset 1.
4. Click Enter and the preset will be saved.
The table will populate with all of the created presets, you can select a preset and
click Go To button, camera will recall this preset position quickly.
Any preset can be deleted by select the preset and clicking the Delete button.

10
Trace:
A Trace is a series of presets, recalled in a given order. This causes the camera to
iterate through the series, moving to each preset in the selected order, support create
8 traces at maximum.
To create a new trace:
1. Select Trace in the PTZ Setting bar
2. Click Create button, it will extend trace number and name field.
3. Select a number and create a name, or just by default name trace 1
4. Then click Start button
Scanning:
Left limit and right limit can be programmed, then camera image (pan) can be set to
move horizontally from left limit to right limit or from right limit to left limit
continuously.
Moving speed can be programmed, speed level from 1-8 adjustable.
Power On Action:
To set actions that the camera will take after the camera is powered on.
You can select the action as preset, patrol, scanning and cruise.
Cruise:
To record a series of camera movements that are pulled by an operator, this series of
movements is called Cruise. You can recall the cruise that has been made, the camera
will re-act all the movements within the cruise.
Fast Setting
Fast setting page can quickly navigate to Device, Network,
Video, Codec and User pages, to set corresponding parameters.
Device: The basic product information of the camera, you can
get the model number, serial number as well as the IP firmware
version information. The IP firmware version may be required
when you submit a camera issue.
Network: The network tab is where the user is able to
configure the camera IP network setting, DHCP or static IP,
including IP address, mask, gateway and DNS server.
Codec: This interface allows user to configure the Main, Sub,
Third video stream parameters, such as the resolution, bitrate
and video compression.
User: This page allows the administrator to create/manage user
accounts and passwords

11
Configuring the camera from the Menu Bar
Camera Setting page can be accessed by clicking the Camera listed in the Menu Bar
Menu Bar is divided into tabs. Under each tab is a collection of settings and parameters that the
user can configure. Please refer to the list of tabs below
Camera-Camera Setting-Video
This setting page is to watch the camera live view image, Pan/Tilt control the camera.
Pan/Tilt Control: Use the arrow buttons to move the camera image position
Camera-Camera Setting-Codec
This setting page is to configure the Main, Sub, Third video stream parameters.
•Main Stream –The main stream,
viewed by default on the Live screen
oVideo Compression:
▪H.264
▪H.265
▪MJPEG
oResolution:
▪1080p60
▪1080p50
▪1080p30
▪1080p25
▪720p60
▪720p50
oBP Frame: Simple P frame
oFrame Rate(fps):Rate at
which image frames are
captured

12
▪1~60 fps adjustable
oBit Rate: The amount of data transmitted per second. Measured in Kilobits Per Second (Kbps). 1000
kbps = 1Mbps
▪128~16384kb/s adjustable
oBitrate Type:
▪CBR –Constant Bit Rate
▪VBR –Variable Bit Rate
oI Frame Interval:
▪5~250 adjustable
oSmoothing:
▪1~9 lever selectable
•Sub Stream –The sub video stream produced by the camera, this can be disabled by unchecking the box next to
the title.
oVideo Compression:
▪H.264
▪H.265
▪MJPEG
oResolution:
▪D1
▪CIF
oBP Frame: Simple P frame
oFrame Rate: Rate at which image frames are captured
▪1~60 fps adjustable
oBit Rate: The amount of data transmitted per second. Measured in Kilobits Per Second (Kbps). 1000
kbps = 1Mbps
▪128~16384kb/s adjustable
oBitrate Type:
▪CBR –Constant Bit Rate
▪VBR –Variable Bit Rate
oI Frame Interval:
▪5~250 adjustable
oSmoothing:
▪1~9 lever selectable
True Dual Output video format setting
This camera supports Bolin True Dual Output functionality, means that you can have relevant IP streaming when
SDI/HDMI video is set to any format you want to set to. It takes SDI/HDMI video format setting as priority.
The following table chart shows the relationship between SDI/HDMI video format and IP video format.
NOTE:
After you have set up the SDI video format to the camera,
the IP format will be determined accordingly.
Within the Video Codec Resolution selection drop down
menu, it will only have relevant IP video formats
displayed for you to select from.

13
Camera-Camera Setting-Snapshoot
This setting page is used to set the camera to
capture the snapshot of the live view, and the
snapshot can be uploaded to FTP server, this
setting is work with FTP upload function together.
Channel 1: Main stream
Level: Quality level of screenshots, supports
Lower, Middle and High selectable
Interval: snapshot frequency, 1000ms by default
Channel 2: Sub stream
Level: Quality level of screenshots, supports
Lower, Middle and High selectable
Interval: snapshot frequency, 1000ms by default
Camera-Camera Setting-OSD
This setting page has the camera live preview, set up title and time display/overlay with the video stream, as well as Logo
upload function.
Title can be configured on Main, Sub and
3rd Stream at the same time, here take the 1-
Title setting for example:
•Input the content that you want to
be displayed as a Title on the video
stream
•It can support 32 characters at
maximum, for example, input
content as Camera 1
•Check the 1-Title option checkbox,
and now the Camera 1 will display
on the IP video

14
•You can click Adjust button (the button will switch to displaying Stop), and then set the Title position by the
right-side Position adjustment module.
•It supports two ways to adjust the Title position, by region or by step
•Adjust by region, you can select from top left, top center, top right, center right, bottom right, bottom center,
bottom left and center left
•Adjust by step, you can configure a step in the rang from 1 to 100, select the direction, and then click set button
to apply it.
•After done, please click Stop button to close the 1-Title adjustment
A logo file can be uploaded and overlay onto the IP
video.
1. logo file must be in bmp format;
2. logo file bit depth must be 24;
3. logo file with dimensions 490x480;
4. User can adjust the logo display position by click
the “adjust” button which beside the logo update,
and then use position adjustment module to
adjust the Logo position, the operation is same as
above Title position adjustment.
5. User can adjust the transparency of the logo
display, support 1~100 adjustable percentage;
NOTE: 1 means fully transparent, 100 means
completely opaque.
Camera-Camera Setting- Privacy Mask
The Privacy Mask setting is for adding a Mask of the image pixels that you want to be covered, then the image portion
that has been covered by a mask will not be seen by the viewer.
Only one mask can be added at a time, a total of 24
convex quadrilateral regions are supported.
NOTE: This feature only works with IP stream, will
not affect the SDI, HDMI or other outputs.
You can set up a privacy mask by performing the
followings
1. Click Start Draw button which under the image
window
2. Move your mouse to the camera image window,
select a point and left click mouse to start
3. Then move to a next point and left click mouse,
do in this way multiple times until you can draw
an area that you desire to have.
4. After finish the area drawing, click Add Mask button, it will be done.

15
This area will be covered in black color by default on
the video, you can change the color by click
PVMKBackground, there have 7 colors selectable.
Any Privacy Mask can be deleted by clicking the Delete
button or Clear All button.
NOTE: Privacy Mask function is not supported in non-IE browsers, and it will not to display this page in web interface
Camera-Camera Setting- Preset CMD
The presets that shown on this page are the pre-programmed commands can be used directly by recalling the relevant
preset numbers.
For example: When you want to turn on the camera Night Mode, just recall Preset No.64, if you want to turn on the
camera day Mode, just set Preset No.64. As create a preset. (select number 64 and press PRESET button for 3 seconds)

16
Audio-Audio Settings
This setting page is to select the audio compression parameters for the Audio input (microphone)
•Audio Compression Options:
oG.711A –Pulse Code Modulation (PCM),
often used to decode voice frequencies
with regard to Telephony
oG.711U –Standard for speech
compression and decompression within
digital transmission systems
oAAC –Advanced Audio Coding
•Bit Rate
oBit rate supports 32K, 48K, 96K and
128K
•Sampling Rate
oSampling rate supports 32K, 44.1K and
48K
•Input Volume
o0 to 100 adjustable by drag the input
volume bar, default is 80
NOTE:
•Bit rate is fixed as 64K and Sampling rate fixed as 8K
when Audio Compression is set to G.711a and G.711u mode
Network-Network Setting-Network
The network tab is where the user is able to configure the following:
•DHCP options
oDHCP –An IP address will be
dynamically assigned to the camera from
the gateway (router)
oStatic IP –The user will enter / define the
IP address
•IP Address
oDefault IP address is 192.168.0.13
•Subnet Mask
oDefault mask is 255.255.255.0
•Default Gateway
oDefault gateway is 192.168.0.1
•Preferred DNS
•Alternate DNS
•MAC Address
oFixed, can’t be modified.
Network-Network Setting-Port
This setting page is to specify which ports the camera will use to communicate with the following protocols:
oTCP Port:
o1 to 65535 adjustable
oUDP Port:
o1 to 65535 adjustable
oRTSP: Default 554
oRTSP is the protocol used to pull real-time
video over the network (using VLC Player
or other network video-compatible
software)
oChanging this port number will change the
way the RTSP video can be viewed. Most
RTSP streaming software uses port 554 by

17
default, therefore it is not recommended that this port number be changed.
oURL for receive RTSP streaming is: rtsp://IP address:554/PSIA/Streaming/channels/0
oVISCA Port (Visca over IP)
oDefault is 52381, it is match with Bolin Keyboard Controller
oUser can change the port number to others to match with third part keyboard controller
oHTTP: Default 80
oHTTP is the protocol used to access the web interface.
oChanging this port number will require the user to specify the port number when entering the IP address
to the web browser.
oFor example, if it is changed to 85, the IP address will need to be entered as follows in order to access
the web interface: http://192.168.0.13:85
NOTE:
VMS Connection
If you use VMS (such as exacqVision) to connect the
camera via ONVIF protocol, you must to include the port
2000 for VMS connection.
For example: If the camera IP address is 192.168.0.13,
you need to enter 192.168.0.13:2000 on VMS
configuration menu.
Network-Network Setting-RTMP
This camera supports RTMP protocol, it can push streaming to other CDN or cloud platform.
oCheck the RTMP
Enable checkbox
oCopy and paste the
stream URL from the
online platform
oCopy and paste the
Stream Key (Also
known as the Stream
ID) from the online
platform.
Example below shows where to
copy the information from YouTube
URL+ Key is not meaning we have to
put the plus sign “+”, just put
“/ “and then put the key after the URL
oClick Apply on camera RTMP page
oAllow a few minutes for the stream to connect. The status on your
streaming platform (Such as YouTube) will change to Live. When this happens, the camera is streaming video
Live to
NOTE: Similar steps can be followed to stream to any platform that supports RTMP, such as YouTube, Facebook,
Twitter, Twitch, etc.)

18
Network-Network Setting-SRT
To establish the communication flow, SRT employs a handshake mechanism in which each device is identified as a caller
or listener. In some cases, two devices can negotiate an SRT session in rendezvous mode at the same time.
SRT Mode
What it can do?
Caller
Set the source or destination device as the initiator of the SRT streaming session
The Caller device must know the IP address and port number of the Listener device
Listener
Set the device to wait for request to start an SRT streaming session
The Listener device just needs to know that it should listen to the SRT streaming on a specific port
Rendezvous
Allows two devices to use the same port to start an SRT session
Both source and destination must be in Rendezvous mode
Camera SRT is set to Off by default, click the drop-down
menu of the Mode option to select a SRT mode.
Mode: User can select from Caller, Listener, Rendezvous
mode, set to Off to disable SRT setting menu.
Caller: SRT Caller mode, the page will expand the caller
mode settings menu, enable Main Stream or Sub Stream as
you want, and configure the corresponding parameters.
•IP Address: The IP address configured on the
Listener device (if you running a software on the
PC as a Listener device, here to enter the PC’s IP
address);
•Port: Configure a port for SRT session, it must
match the SRT port number of the Listener device
(the range is 1~65535);
•Stream ID: SRT streaming ID, you can set one or
keep it as default (please configure the same
Stream ID on Listener device);
•Latency: Delay between the Caller device and
Listener device, can be set from 20~5000ms;
NOTE: When camera set to Caller mode, then the camera can only send SRT stream to one receiver (configured in
Listener mode).
Listener: SRT Listener mode, the page will expand the listener mode settings menu, enable Main Stream or Sub Stream
as you want, and configure the corresponding parameters.
•Port: Configure a port for SRT session, it must
match the SRT port number of the Caller device
(the range is 1~65535);
•Stream ID: SRT streaming ID, you can set one or
keep it as default (please configure the same
Stream ID on Caller device);
•Latency: Delay between the Caller device and
Listener device, can be set from 20~5000ms;
NOTE: When the camera set to Listener mode, multiple
receives (configured in Caller mode) can be allowed to
receive this SRT streaming.

19
Rendezvous: SRT Rendezvous mode, the page will
expand the rendezvous mode settings menu, enable Main
Stream or Sun Stream as you want, and configure the
corresponding parameters.
•IP Address: The IP address of the other end SRT device
(configured in Rendezvous mode)
•Port: Configure a port for SRT session, it must match
the SRT port of the other end SRT device (configured in
Rendezvous mode)
•Stream ID: SRT streaming ID, you can set one or keep it
as default (please configure the same Stream ID on the
other end SRT device)
•Latency: Delay between the two SRT device (configured
in Rendezvous mode)
NOTE: When camera set to Rendezvous mode, then the
camera can only send SRT stream to one receiver
(configured in Listener mode).
Network-Network Setting-FTP
1. Check the Enable option
2. Input the FTP server IP address into the Server IP
option bar
3. Input the FTP port number into the Server Port option
bar, the port must be same as configured on FTP
server, it should be port 21 usually.
4. Input FTP server name and password into the Server
username and Server password option bar, it must be
same as configured on the FTP server
5. Select the Path Type and Path that you want the
snapshot be saved on FTP server
NOTE: FTP function is work with snapshot function
together, please make sure already enabledsnapshot and
configured the properly interval of uploaded time.
Network-Network Setting-Multicast
This setting page is used to configure multicast for Main,
Second and Third stream, for save bandwidth purpose in
live streaming application. Here takes Main Stream for
example:
oFollowing the Multicast address rang to configure
a multicast IP address for Main Stream;
oFollowing the Multicast Port rang to configure a
multicast port for Main Stream;
oClick the Apply button and restart camera once to
make the settings take effect;
oAfter camera power cycle, click copy button to
copy the multicast URL address
User can use VLC Media Player to receive the camera
multicast stream, operation as below:
oRunning VLC Media Player
oClick Media menu which on the upper left corner,
and select Open Network Stream…

20
oInput the copied multicast URL address into the Network URL bar;
oClick Play button and now you can get the multicast of Main Stream
System-System Setting- Device
This setting page is to get the basic product information of the camera.
•Device Name
oYou can set a name to this camera
•Model Number
oThe specific model of this camera
•Product Serial Number
oThe serial number of this camera, each
serial number is unique and fixed, can’t be
modified.
•Encoder Version
oThe current encoder version running on
this camera
•MCU Version
oThe current MCU version running on this
camera
•Web Plugins Version
oThe current web interface plugin version
running on this camera
You may be asked to provide above information by Bolin
technical team for any possible technical support cases.
System-System Setting-Time
This interface allows user to configure the date / time settings of the camera
•System Time
oYou can check the Sync with Computer
Time option and synchronize the camera
operation time with your PC time system.
•Date Format
oTwo formats selectable
oY-M-D or D/M/Y
•Time Format
oTwo formats selectable
o24H or 12H standard
•Time Zone
oWEST 12 to EAST 12 selectable
oPlease select the correct time zone for your
location
•Network Time Sync
oCheck the Enable option
oInput the time sync server address, port
number
oSelect refresh time option, it has 10 Min,
30Min, 1 Hour, 1 Day selectable.
After done the configuration, please remember to click Apply button to make the setting activated. You also can click
Default Setting to restore settings to default if you want to.