Bolin Technology VCC-7HD20S-3SMC User manual

1
7 Series SDI/HDMI
HD PTZ Camera
USER MANUAL
VERSION: VCC-7HD-M-01072019
VCC-7HD20S-3SMC
VCC-7HD30S-3SMC
© 2018 Bolin Technology

2
Contents
IMPORTANT INFORMATION ..................................................................................................................................................... 3
WHAT’S IN THE BOX ................................................................................................................................................................. 6
OVERVIEW................................................................................................................................................................................ 7
FEATURES ................................................................................................................................................................................. 7
CAMERA DIAGRAMS................................................................................................................................................................. 8
REMOTE CONTROLLER ........................................................................................................................................................................ 9
SYSTEM CONFIGURATION....................................................................................................................................................... 10
OBTAIN VIDEO SIGNAL ..................................................................................................................................................................... 11
CAMERA CONTROL METHODS AND SYSTEM CONFIGURATIONS............................................................................................. 12
USE THE INFRARED REMOTE CONTROLLER ............................................................................................................................................ 12
USE RS-232 (VISCA)...................................................................................................................................................................... 12
USE RS-422(VISCA) /RS485 (PELCO P/D) ..................................................................................................................................... 14
RS422 (VISCA) CONNECTION ........................................................................................................................................................... 14
PELCO P/D KEYBOARD RS485 CONNECTION ...................................................................................................................................... 16
HOW TO MAKE THE CONNECTION WITH BOLIN PRODUCTS ...................................................................................................................... 18
DIP SWITCH SETTINGS ............................................................................................................................................................ 19
ADJUSTING AND SETTING WITH MENUS................................................................................................................................. 21
EXPOSURE MENU ......................................................................................................................................................................... 22
WHITE BALANCE MENU................................................................................................................................................................ 23
PICTURE1 MENU........................................................................................................................................................................... 24
PICTURE2 .................................................................................................................................................................................... 25
PAN TILT ZOOM MENU................................................................................................................................................................. 25
SYSTEM MENU.............................................................................................................................................................................. 26
UPGRADING MCU FIRMWARE........................................................................................................................................................... 27
OPERATION USING THE INFRARED REMOTE CONTROLLER ..................................................................................................... 28
PAN/TILT AND ZOOM OPERATION ...................................................................................................................................................... 28
OPERATING MULTIPLE CAMERAS WITH THE INFRARED REMOTE CONTROLLER.............................................................................................. 29
ADJUSTING THE CAMERA................................................................................................................................................................... 29
STORING THE CAMERA SETTINGS IN MEMORY —THE PRESETTINGFEATURE ............................................................................................... 30
MENU CONFIGURATION ......................................................................................................................................................... 31
DIMENSION ............................................................................................................................................................................ 32

3
Operating Instructions
Thank you for purchasing our product. If there are any questions, please contact the authorized dealer.
Before operating the unit, please read this manualthoroughly and retain it for futurereference.
Copyright
Copyright 2015-2018 Bolin Technology all rights reserved. No part of this manual may be copied, reproduced,
translated, or distributed in any form or by any means without prior consent in writing from our company.
Trademark Acknowledgement
and other Bolin's trademarks and logos are the property of Bolin Technology Other trademarks,
company names and product names contained in this manual are the property of their respective owners.
Trademarks and Registered Trademark Acknowledgement
Microsoft, Windows, ActiveX, and Internet Explorer are registered trademarks of Microsoft Corporation in the
U.S. and/or other countries.
HDMI, the HDMI logo and High-Definition Multimedia Interface are the trademarks or registered trademarks of
HDMI Licensing, LLC in the United States and other countries.
The Software may contain h.264/AVC video technology, the use of which requires the following notice from
MPEG-LA, L.L.C.:
THIS SOFTWARE IS LICENSED UNDER THE AVC PATENT PORTFOLIO LICENSE FOR THE PERSONAL AND
NON-COMMERCIAL USE OF A CONSUMER TO (I) ENCODE VIDEO IN COMPLIANCE WITH THE AVC
STANDARD ("AVC VIDEO") AND/OR (II) DECODE AVC VIDEO THAT WAS ENCODED BY A CONSUMER
ENGAGED IN A PERSONAL AND NON-COMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO
PROVIDER LICENSED TO PROVIDE AVC VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR
ANY OTHER USE. ADDITIONAL INFORMATION MAY BE OBTAINED FROM MPEG LA, L.L.C. SEE
http://www.mpegla.com.
HEVC/h.265 Covered by one or more claims of patents listed at patentlist.hevcadvance.com
HDBaseT is a trademark of the HDBaseT Alliance.
ONVIF trademarks and logos are to be used per the guidelines established in this and other ONVIF policies and
documents including the ONVIF Rules of Membership and the ONVIF Logo Guidelines1.
Other trademarks, company names and product names contained in this manual are the property of their respective
owners.
IMPORTANT INFORMATION
Legal Notice
Attention:
To ensure account security, please change the password after your first login. You are recommended to set a strong
password (no less than eight characters). Password login does not apply to some models that do not need password login.
The contents of this document are subject to change without prior notice. Updates will be added to the new version of this
manual. We will readily improve or update the products or procedures described in the manual.

4
Best effort has been made to verify the integrity and correctness of the contents in this document, but no statement, information,
or recommendation in this manual shall constitute formal guarantee of any kind, expressed or implied. We shall not be held
responsible for any technical or typographical errors in this manual.
The product appearance shown in this manual is for reference only and may be different from the actual appearance of your
device.
This manual is a guide for multiple product models and so it is not intended for any specific product.
In this manual, the illustrations of displayed interface, parameters displayed, drawings and value ranges may vary with models.
Please see the actual product for details.
Due to uncertainties such as physical environment, discrepancy may exist between the actual values and reference values
provided in this manual.
Use of this document and the subsequent results shall be entirely on the user’s own responsibility.
Symbols
Symbol
Description
WARNING!
Contains important safety instructions and indicates situations that may cause bodily injury.
CAUTION!
User must be careful and improper operations may cause damage or malfunction of product.
NOTE!
Indicates useful or supplemental informationabout the use of product.
Safety Information
WARNING!
Installation and removal of the unit and its accessories must be carried out by qualified personnel. You must read all of
the Safety Instructions supplied with your equipment before installation andoperation.
Warnings:
If the product does not work properly, please contact your dealer. Never attempt to disassemble the camera yourself.
(We will not assume any responsibility for problems caused by unauthorized repair or maintenance.)
This installation should be made by a qualified service person and should conform to all the local codes.
When shipping, the camera should be packed in its originalpackaging.
Make sure the power supply voltage is correct before using the camera.
Do not drop the camera or subject it to physicalshock.
Do not touch sensor modules with fingers. If cleaning is necessary, use a clean cloth with a bit of ethanol and wipe it
gently. If the camera will not be used for an extended period of time, put on the lens cap to protect the sensor from dirt.
Do not aim the camera lens at the strong light such as sun or incandescent lamp. The strong light can cause fatal
damage to the camera.
Maintenance Precautions:
If there is dust on the front glass surface, remove the dust gently using an oil-free brush or a rubber dust blowing
ball.
If there is grease or a dust stain on the front glass surface, clean the glass surface gently from the center outward

5
using anti-static gloves or an oil-free cloth. If the grease or the stain still cannot be removed, use anti-static
gloves or an oil-free cloth dipped with detergent and clean the glass surface gently until it is removed.
Do not use organic solvents, such as benzene or ethanol when cleaning the front glass surface.
Regulatory Compliance
FCC Part 15
This equipment has been tested and found to comply with the limits for digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
This product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired operation.
LVD/EMC Directive
This product complies with the European Low Voltage Directive 2006/95/EC and EMC Directive
2004/108/EC.
WEEE Directive–2002/96/EC
The product this manual refers to is covered by the Waste Electrical & Electronic Equipment (WEEE)
Directive and must be disposed of in a responsible manner.

6
WHAT’S IN THE BOX
Accessories (Optional)

7
Overview
This user guide is suitable for the following models:
VCC-7HD20S-3SMC
VCC-7HD30S-3SMC
Features
Resolution: Up to 1080P60, 1080i59.94
IP Resolution: Up to 1080P60, 1080P30
Zoom: Optical 20X, 30X
Image stabilizer(30X) and true WDR 130dB
Video Output: HDMI, 3G-SDI, CVBS simultaneously
±350-degree continuous pan, ±120-degree continuous tilt
128 presets, Speed up to 150 degrees/sec
Standard mounting and ceiling mounting with E-Flip function
Control supports RS-232 control, RS-422/485 control, VISCA, Pelco D protocol, IR Remote
Controller.
Presets store camera directions and image parameters. (Up to 6 presets on remote controller or
128 presets via protocol programming.)
Image parameter setting restore with presets and quick access operation
Power: DC 12V
Firmware upgrade via USB2.0 or IP

8
Camera Diagrams
1. 12V DC Power Port
Connect the supplied DC power adaptor and cord.
2. USB2.0 Port
For firmware upgrade only
3. RS232 Control Port (RJ45)
RJ45 to RS232 convertor cable is provided.
4. Video Format Selector
For video format selection
5. RS-422 Control Port (RJ45)
RJ45 to RS422 convertor cable is provided.
6. IR Remote ID Selector
Camera ID for IR remote controller
7. HDMI Port (HDMI 1.4)
8. CVBS Video Output
9. 3G-SDI Video Output
10. IR Remote Controller Sensors
These are sensors to receive commands from infrared remote controller.
11. Lens
This is a 20X/30X magnification optical zoom lens
12. Power LED Indicator
Turns green when the camera is connected to power outlet. When the power is turned on, it takes about 15 to 30
seconds to display the image after LED turns on.
13. Fix Mounting Holes
For original wall/ceiling mount bracket
14. Tripod mounting holes
15. Bottom DIP Switch

9
Remote Controller
1. Power
Power ON the camera to turn the camera in operation
status.
Power OFF the camera to turn the camera in
standby status.
When the camera is powered OFF, the camera turns to
the back and would be on standby mode.
When the camera is powered ON, the camera turns to
the front.
Powering the camera ON/OFF would not restart the
camera.
2. Camera ID (Total 3) Selector
3. Preset Position (Total 6) Calling and Setting
4. PAN-TILT
Pan and Tilt direction control
HOME: Home position, Resolution reset
5. L/R Direction Set
Left and right orientation setting
6. ZOOM/FOCUS
Far
Near
7. Auto/Manual Focus
8. Back Light
9. Video Format Switching
You can change the video format by keep pressing
the button. (When video format is changed, the
camera would restart and the screen turns black
for few seconds.)
10. MENU
On screen menu display ON/OFF
11. Audio Switch
You can turn the Mic built in the camera Off/ON by pressing the button once.
12. Fast/Slow Zooming Speed Switching
13. White Balance
Change the White Balance setting by pressing the button.
14. De-Flicker
When you find the video flicking, press the button once to eliminate the flickers.
Notes
3V CR2032 Coin lithium Battery is not included with the remote controller.
3V CR2032 Coin lithium batteries arenot re-changeable.

10
System Configuration
Connection
In this connection configuration, HDMI cable, SDI video cable, data cable, Network cable is required. To obtain these third-
party components or accessories,
Power
Use only the DC power adaptor (JEITA type4) supplied with the unit. Do not use any
otherDC power adaptor.
Cable Requirements
SDI Cable: For broadcast use,
Belden1694A/5CFB is a suitable cable to
transmit broadcast-quality video:

11
Conductor:
AWG
Stranding
Material
Nominal Diameter
18
Solid
Bare Copper
0.04 in.
Shield Material
Nom. Capacitance
Conductor to shield
Nom. Inductance
Nom. Char. Impedance
16.2 pF/ft
0.106 µH/ft
75 Ohm
Obtain Video Signal
The camera can simultaneously have SDI video output and HDMI video output and IP video output.
HDMI HD Video signal
1. Connect the camera to a HD monitor/TV using HDMI cable.
2. Turn on the camera, video will display on the monitor after running initializing.
3. Information of the camera initial setting status will display for 5 seconds.
4. You can set the video format of the camera to the one you want to display.
SDI Video Signal
The camera can simultaneously stream SDI video output with HDMI video output.
1. Connect SDI cable in between the camera your SDI Device/display.
2. You now have SDI video output.
3. SDI video only supports 1080P.
CVBS Video Signal
1. Connect CVBS cable in between the camera and your CVBS Device/display.
2. You now have CVBS video output.
Camera Initial setting status Information
Information of the camera initial setting status will display for 5 seconds.
1. Camera PELCO ID for RS-485 control
2. Camera ID for IR Remote Controller
3. IR remote control signal receive current setting
4. Baud Rate current setting
5. Control COMM Port current setting
6. Video format current setting
7. HDMI current setting
8. Model number
9. Firmware version
Type
Layer
Material
Coverage
Tape
1
Aluminum / Polyester / Aluminum
100%
Braid
2
Tinned Copper
95%
PELCO ID 001
IR ID 01
IR-RECEIVE ON
BAUD RATE 9600
COMM TYPE 422
FORMAT 1080P29.97
HDMI OUT YUV
MODEL TYPE ----
SV: V0B1100S36040AD04
Camera Status Info Display

12
Camera Control Methods and System Configurations
This unit has multiple ways of controlling the camera and various system configuration capabilities using optional
products. This section describes the ways of controlling and typical system examples with the required components and
usage of each system.
1. Use the Infrared Remote Controller
2. Use RS-232 (VISCA)
3. Use RS-422/485 (VISCA/PELCO P/D)
Use the Infrared Remote Controller
To operate the camera from a short distance.
For IR remote control details, refer to Operation Using the Infrared Remote Controller.
Use RS-232 (VISCA)
You can use RS-232 port to connect to optional controllers, such as joystick control keyboard, control PC station, to
operate the camera.
To perform pan/tilt and zoom operations using the joystick of the control keyboard, and to perform the Preset operation
using the control buttons.
An application software that supports this unit is needed if you use PC station.
RS232 Connection
1. Set RS232 control method on Bottom Dip Switch.
2. Set Baud Rate on Bottom Dip Switch to the same as Baud Rate setting on the keyboard you are using.
3. Set specific camera address that you want to control the camera for on Bottom Dip Switch.
4. If you want to have the camera address to be automatically assigned by VISCA controller, set camera Dip Switch address to
0.
5. Reboot the camera by turning it Off/On after the Bottom Dip Switch has been set up correctly.
6. Camera supports Daisy Chain connection up to 7 cameras.
7. Use the RJ45 to RS232 (VISCA) control cable. The controller must be VISCA compatible.

13
8. You can make RS232 connection cable if you have the following applications:
9. Use extension cables included RJ45 to RS232 8 pin Mini Din adaptor to make RS232 connection for your control device.
10. Use extension cables included RJ45 to RS422/232 Phoenix terminal contact adaptor to make RS232 connection for your
control device.
11. Or you can use CAT5/6 network cable to make RS232 connection by following the
pin definition below:

14
12. How to make RS232 Daisy Chain multiple camera connection with standard RS232 serial port controller as
below:
Use RS-422(VISCA) / RS485 (PELCO P/D)
You can use RS-422/485 port connect to optional controllers, such as joystick control keyboard, control PC station, to
operate the camera.
To perform pan/tilt and zoom operations using the joystick of the control keyboard, and to perform the Preset operation
using the control buttons.
An application software that supports this unit is needed if you use PC station.
RS422 (VISCA) connection
1. Set RS422 control method on Bottom Dip Switch.
2. Set Baud Rate on Bottom Dip Switch to the same as Baud Rate setting on the keyboard you are using.
3. Set specific camera address that you want to control the camera for on Bottom Dip Switch.
4. If you want to have the camera address to be automatically assigned by VISCA controller, set camera Dip Switch address to
0.
5. Reboot the camera by turning it Off/On after the Bottom Dip Switch has been set up correctly.
6. Use the RJ45 to RS422 control cable. The controller must be VISCA compatible.
7. Camera supports Daisy Chain connection up to 7 cameras.
8. The connection of SONY keyboard is different than other VISCA (Non-Sony) keyboard.
9. How to make RS422 connection and RS422 Daisy Chain multiple cameras connection with SONY controller as below

15
SONY Keyboard RS422 Connection
10. How to make RS422 connection and RS422 Daisy Chain multiple cameras connection with Non-Sony controller as below:
VISCA (Non-Sony) Keyboard RS422 Connection
11. Use extension cables RJ45 to RS422 Phoenix connecter adaptor included to make RS422 connection for your control device.
12. Or you can use CAT5/6 T-568B Standard Ethernet cable direct connect between the camera and the controller to make
RS422 connection by following the pin definition below:

16
13. How to make RS422 Daisy Chain multiple camera connection with RS422 standard serial port controller:
PELCO P/D Keyboard RS485 Connection
Set RS422 control method on Bottom Dip Switch.
Set Baud Rate on Bottom Dip Switch to the same as Baud Rate setting on the keyboard you are using.
Set the camera ID on OSD menu by remote controller
Reboot the camera by turning it Off/On after the Bottom Dip Switch has been set up correctly.
Use PELCO P/D compatible keyboard.
Use preset 95# on the keyboard to bring up/exit camera OSD menu.
Use joystick and Button “OPEN” or “CLOSE” to navigate OSD menu.
To operate keyboard, please refer to the user manual of the keyboard you are using.
PELCO RS485 Connection

17
Use extension cables included RJ45 to RS422 Phoenix connecter adaptor to make RS485 connection for your control device.
Or you can use CAT5/6 T-568B Standard Ethernet cable direct connect between the camera and the controller to make
RS485 connection by following the pin definition below:
How to make RS485 multiple cameras connection with RS485 standard serial port controller:

18
Note
For RS-232 VISCA control, this unit supports daisy chain connection for using multiple cameras.
For control details, refer to Operating Instructions of control keyboard/station software.
You need to match the communication speed (Baud Rate) between the camera and the joystick controller.
You cannot use the RS-232 connections while you are using the RS422/485 connection.
Operating Multiple Cameras Using RS-232,422/485
Using RS-232 (VISCA), you can connect to 7 cameras.
Using RS-422 (VISCA), you can connect to 7 cameras.
Using RS-485 (PELCO), you can connect to 255 cameras.
Using RS-485 (PELCO), all camera addresses must be set up before the connection. You can set the camera
address by operating OSD menu, or by setting the Dip Switch on the bottom of the camera. In this case, you can
use multiple control keyboards.
How to make the connection with BOLIN products
Please see the User Guide “BOLIN Camera and Keyboard Controller Connection”
that you can download it at www.bolintechnology.com product pages.

19
DIP SWITCH SETTINGS
The Dip switches are for setting the camera configuration for following items:
1. Camera ID Address for RS-485 PELCO protocol
2. Video output / Video color space
3. RS-232 / RS-422/485 selection
4. RS-232 / RS-422/485 baud rate
5. Video resolutions selection
6. IR remote controller ID
Setting of the BOTTOM DIPSwitches
Turnoffpowertothecamerabeforechanging the DIP switch settings.
Power on the camera to have the new Dip Switch setting activated.
From the above list, No.1 Camera ID address and NO.2 Video resolution settings can be set in camera OSD menu as
well. The camera takes either the way of OSD menu setting or the way of bottom DIP switch setting. They override each
other. After the camera is turned on, the camera takes the last setting before it is turned on, either set through the OSD or
bottom DIP switch.
The Bottom DIP Switch Settings
Bit 1~3: Camera Address setting for VISCA protocol
Bit 4: Video Output/Video Color Space
Bit 5: Reserve
Bit 6: RS-232/RS-422
Bit 7~8: RS-232/RS-422 Baud Rate

20
Setting of the back panel Rotate DIPSwitches
The Rotate Dip Switch is for setting video format.
Use small screw driver to turn the switch, the arrow points to the Numbers or the Letters. The video format that the
Number or Letter stands for refer to the video format as the chart following:
IR Remote Controller ID Setting
Set the IR SELECT switch on the back panel of the camera to 1, 2 or 3, which is the camera ID number that you want to
operate on the Remote Controller.
Numbers & Letters
Video Resolution
0
1080i59.94
1
1080P29.97
2
720P59.94
3
1080P59.94
4
1080P50
5
1080I60
6
1080P30
7
1080P60
8
1080I50
9
1080P25
A
720P50
B
1080P50
C
720P25
D
720P30
E
720P60
F
-