Bolin Technology EX1030SHD-B-L5SNAP1 User manual

1
EX1000 SDI+IP SERIES
IR LASER PTZ CAMERA
USER MANUAL
Part One: Camera User Manual
VERSION: EXSN-B-M-10162017
© 2017 Bolin Technology

2
Contents
IMPORTANT INFORMATION........................................................................................................................................................3
OVERVIEW ..................................................................................................................................................................................5
WHAT’S IN THE BOX ........................................................................................................................................................................6
CAMERA DIAGRAMS ...................................................................................................................................................................7
INSTALLING YOUR CAMERA ........................................................................................................................................................8
POWER INPUT .....................................................................................................................................................................................9
MOUNTING THE CAMERA ....................................................................................................................................................................10
LASER ILLUMINATOR.................................................................................................................................................................11
USE SDI VIDEO OUTPUT ............................................................................................................................................................12
STARTING THE CAMERA.......................................................................................................................................................................12
CONTROLLING THE CAMERA.................................................................................................................................................................14
ADJUSTING AND SETTING WITH MENUS..................................................................................................................................................14
THE ON-SCREEN MENU CONFIGURATION...............................................................................................................................................15
VIDEO FORMAT: ............................................................................................................................................................................19
USE IP VIDEO OUTPUT ..............................................................................................................................................................23
SETTING CAMERA OVER THE LAN..........................................................................................................................................................23
ACCESSING YOUR CAMERA ..................................................................................................................................................................23
INSTALLING THE ACTIVEX.....................................................................................................................................................................24
DIMENSIONS.............................................................................................................................................................................25
SPECIFICATIONS ........................................................................................................................................................................26

3
Operating Instructions
Thank you for purchasing our product. If there are any questions, please contact the authorized dealer.
Before operating the unit, please read this manualthoroughly and retain it for futurereference.
Copyright
Copyright 2015-2016 Bolin Technology all rights reserved. No part of this manual may be copied, reproduced,
translated, or distributed in any form or by any means without prior consent in writing from our company.
Trademark Acknowledgement
and other Bolin's trademarks and logos are the property of Bolin Technology Other trademarks,
company names and product names contained in this manual are the property of their respective owners.
IMPORTANT INFORMATION
Legal Notice
Attention:
To ensure account security, please change the password after your first login. You are recommended to set a strong
password (no less than eightcharacters). Password login does not apply to some models that do not need password login.
The contents of this document are subject to change without prior notice. Updates will be added to the new version of this
manual. We will readily improve or update the products or procedures described in the manual.
Best effort has been made to verify the integrity and correctness of the contents in this document, but no statement, information,
or recommendation in this manual shall constitute formal guarantee of any kind, expressed or implied. We shall not be held
responsible for any technical or typographical errors in this manual.
The product appearance shown in this manual is for reference only and may be different from the actual appearance of your
device.
This manual is a guide for multiple product models and so it is not intended for any specific product.
In this manual, the illustrations of displayed interface, parameters displayed, drawings and value ranges may vary with models.
Please see the actual product for details.
Due to uncertainties such as physical environment, discrepancy may exist between the actual values and reference values
provided in this manual.
Use of this document and the subsequent results shall be entirely on the user’s own responsibility.
Symbols
Symbol
Description
WARNING!
Contains important safety instructions and indicates situations that may cause bodily injury.
CAUTION!
User must be careful and improper operations may cause damage or malfunction of product.
NOTE!
Indicates useful or supplemental information about the use of product.
Safety Information
WARNING!
Installation and removal of the unit and its accessories must be carried out by qualified personnel. You must read all of
the Safety Instructions supplied with your equipment before installation andoperation.

4
Warnings:
If the product does not work properly, please contact your dealer. Never attempt to disassemble the camera yourself.
(We will not assume any responsibility for problems caused by unauthorized repair or maintenance.)
This installation should be made by a qualified service person and should conform to all the local codes.
When shipping, the camera should be packed in its originalpackaging.
Make sure the power supply voltage is correct before using the camera.
Do not drop the camera or subject it to physicalshock.
Do not touch sensor modules with fingers. If cleaning is necessary, use a clean
cloth with a bit of ethanol and wipe it gently. If the camera will not be used for an
extended period of time, put on the lens cap to protect the sensor from dirt.
Do not aim the camera lens at the strong light such as sun or incandescent lamp. The strong light can cause fatal
damage to the camera.
The sensor may be burned out by a laser beam, so when any laser equipment is being used, make sure that the
surface of the sensor not be exposed to the laser beam.
Mount laser dome camera at a height of six meters (19.7 ft) from the ground. To avoid bodily injury from the laser
radiation, please make sure that no one is within the range of three meters (9ft) from the camera when the laser is
working.
Never look at operating laser while the power is on.
Caution: Use of controls or adjustments to the performance or procedures other than those specified herein may
result in hazardous laser emissions.
Maintenance Precautions:
If there is dust on the front glass surface, remove the dust gently using an oil-free brush or a rubber dust blowing
ball.
If there is grease or a dust stain on the front glass surface, clean the glass surface gently from the center outward
using anti-static gloves or an oil-free cloth. If the grease or the stain still cannot be removed, use anti-static gloves
or an oil-free cloth dipped with detergent and clean the glass surface gently until it is removed.
Do not use organic solvents, such as benzene or ethanol when cleaning the front glass surface.
Regulatory Compliance
FCC Part 15
This equipment has been tested and found to comply with the limits for digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
This product complies with Part 15 of the FCC Rules. Operation is subject to the following twoconditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired operation.
LVD/EMC Directive
This product complies with the European Low Voltage Directive 2006/95/EC and EMC Directive
2004/108/EC.
WEEE Directive–2002/96/EC
The product this manual refers to is covered by the Waste Electrical & Electronic Equipment (WEEE)
Directive and must be disposed of in a responsible manner.

5
Overview
Model Numbers
This user guide is suitable for the following models:
If the model numbers that have following letter included in the end, means some extra features included:
1. B Class –Use for broadcasting, SDI video format 1080P and 1080I supported, frame rate up to 60/59.94.
2. S Class –Use for video surveillance or other applications, SDI video format 1080P and 720P supported,
frame rate up to 60.
EX1030SHD-B-L5SA1 (SDI+IP, Nitrogen)
EX1030SHD-B-L5SNAP1 (SDI+IP, Nitrogen, POE)
EX1030SHD-S-L5SA1 (SDI+ IP, Nitrogen)
EX1030SHD-S-L5SNAP1 (SDI+IP, Nitrogen, POE)
Features
Supports Various Resolutions: 1080P, 720P
Zoom: 20X,30X
Supports ONVIF Compliant
Video Compression: H.264/MJPEG
RS485/RS422 Communication, Auto compatible with PELCO-D and VISCA Protocol
Store image parameter (iris, white balance, exposure, picture setting) to a specified preset
3D Positioning
120dB true WDR
Video Output: SDI+IP, True Dual-Output SDI+IP Simultaneously
Adaptive IR laser illumination distance up to 500 Meters
Outdoor Environmental Rating: IP67, Corrosion Resistant Treatment, Nitrogen Filled Housing
Input Power: Provides AC24V and POE (Bolin PoE 80W Injector needed, optional)
Various Image Functionalities: WDR, BLC, Defog, Day/Night
Supports ±120°tilt / ±360°pan range, adaptive speed up to 90°/s
Supports Preset Time Task Activation: 8 Periods
Supports 255 Presets speed adaptive up to 80°/s, 8 Cruises
Supports Zoom Lens Position and Direction Indicator on OSD
Working temperature: -40°C to 60°C
Nitrogen Filled Housing
Resistance to wind: 60m/s
Vandal Resistant: IK10

6
WHAT’S IN THE BOX
Accessories- Optional

7
Camera Diagrams
Camera
Tail-Cable
All cables are tagged to indicate their functions separately. The cables available may vary with the product model.

8
Cable Connection
NOTE!
Use water proof / IP67 rated junction box/ connection box to protect the RJ45 and other connections. A water proof RJ45
connector is available on some models.
Installing Your Camera
The following diagrams are for your reference only. See the actual product to mount your
camera.
Check Camera Components and Installation Conditions
Before mounting your camera, check the device model number and included contents
against the packing list to ensure components are complete.
Camera Structure
1. Tail-Cable
2. Camera Body
Important
Verify the bearing capacity of the mounted position
Verify that the mounted position meets the bearing requirements. Otherwise, you are advised to reinforce the
mounted position for the device weight. For more information, see the product datasheet.
Verify lightning protection and grounding requirements
Select proper lightning protection devices for the power supply, video signal interfaces, and RS485 interfaces.
Ground the terminal properly.

9
Cable Requirements
Network cable
10/100 Mbps Ethernet CAT 5/5E UTP cables are applicable to the ANSI/EIA/TIA-568A/B and ISO/D.
Eight wires in the network cable need to be inserted in parallel into the top of the cable connector. The cable connector
needs to be crimped in position. When the cable connector is in position, ensure that the metal pieces of the cable
connector are parallel to each other and the clamp of the cable connector is intact.
SDI Signal Cable
In order to ensure the quality of the installation of the project, the HD-SDI and 3G-SDI signals have a high data
transmission rate of digital signals, it is necessary to correctly select the appropriate cable model. In the process of
installing a cable, it should be carefully and carefully, to avoid incorrect to fold, twist, bend the cable or to apply various
kinds of stress to the cable, so that the signal can be transmitted along the cable smoothly.
Different cable types have different physical characteristics, and the transmission length of the digital signal is not the
same.
Recommended cable
Transmission signal
Transmission distance
Belden 7731A
3G-SDI
120 m
128 above the double shield 75-5
HD-SDI
70 m
Power Input
Bolin PTZ camera provides 24VAC power input
Power Cable
Data listed in the below table is applicable to copper cables that use 24 VAC/24 VDC power supply. The item Core
Diameter indicates the conductor diameter.
Power Loss on the Cable for Different Lengths and Different Core Diameters
Core Diameter
(Unit: mm)
Distance
(Unit: m)
Power (Unit: VA)
0.80
1.00
1.25
2.00
10
86
137
218
551
20
42
68
109
275
30
28
45
72
183
40
21
34
54
137
50
17
27
43
110
60
14
22
36
91
70
12
19
31
78
80
10
17
27
68
90
9
15
24
61
100
8
13
21
55
110
7
12
19
49
120
7
11
17
45
130
6
10
16
42
140
6
9
15
39
150
5
9
14
36
160
5
8
13
34

10
170
4
7
12
32
180
4
7
11
30
190
4
7
11
28
200
4
6
10
27
NOTE:
Important: Power supply requirement is 24VAC 2.5 Amp to ensure proper functionality of PT motor and LED
illumination. Using power supply lower than 24VAC 2.5Amp will cause camera crashing or insatiability.
Power Connector: Phoenix Connector Description
1. The anode and the cathode are not distinguished for phoenix connectors of red and black cables.
2. GND: yellow-green color.
Note: GND is used to ground the camera. Ensure that GND is connected to a reliable grounding point.
PoE Power Injector
Other than 24VAC power input, Bolin PTZ camera provides PoE power as an optional power input.
For PoE power, you must use Bolin 80W Power PoE Injector: model BL-PP80. It provides high PoE power up to the PTZ
camera. Connect this PoE injector to a network switch and then run Ethernet cable for data transmission and power up the
PoE PTZ camera (Specific model: EX1000 & SD500 Series) for distance up to 100 meters.
NOTE!
Disconnect the power from the camera beforemounting.
Accessories such as the wall mount bracket and the pendant mount bracket may be necessary during mounting. For
their model, refer to the accessory list recommended by your dealer.
The wall bearing capacity and the bracket length must meet all onsite mounting requirements. You will need to
select a mount type based the actual environment.
Mounting the Camera
NOTE!
When mounting the camera, please install the bracket adapter to the bracket first and then mount the camera to
thebracket.
Tighten all the screws to hold the camera securely.
For waterproofing, apply sealant between the dome and the bracket, wall veneer slits, and leading-out holes of the
wall.

11
Wall Mount
1. Open the bracket cover, mount it onto the wall or pole (use pole adaptor).
2. Put on 3 screws onto the bottom of the camera, leave enough space to fit in the
screw holes on the bracket, not to screw tight.
3. Hold up the camera close under the bracket, insert the tail-cable of the camera
into the chest of the bracket.
4. Insert the 3 screws into the screw holes and turn the camera counter-clock wise
so that the camera can be held by the camera. Screw up the 3 screws but not too
tight.
5. Put on the 4th screw and screw in tightly. Screw in the rest of the screws tightly.
6. Finish the cable connection. Put all cable and connectors inside of the bracket.
7. Put the cover back to the bracket and screw in securely.
Laser Illuminator
Adaptive IR Laser Illuminator
The EX1000 PTZ series camera uses adaptive IR laser illuminator to provide up to 500 meters of long range
Illumination. IR laser uses diffused illumination that provide the long distance visibility.
Precaution & Specs:
1. This product uses Class 3B laser light product.
2. Supports Manual / Auto IR laser control
3. Uses synchronous zoom with continuously adjustable illumination angle of 68 °~ 2 °.
4. Supports intelligent light-adjustment which automatically adjust the power of infrared laser light and avoids
reflective object and close range image overexposure.
5. Mount a laser dome camera at a height of six (6) meters (19.7 ft) from the ground. To avoid bodily injury
from the laser radiation, please make sure that no one is within the range of three (3) meters (9 ft) from the
camera when the laser is working.
6. When the IR laser is operating, do not look directly into the laser beam or obstruct the pathway of the beam.
Everyone who uses a laser should be aware of the risks and take necessary caution when handling, operating and
maintaining the product.
This camera can provide SDI video output, IP video output separately and SDI + IP video outputs simultaneously.
The following sections are the instructions of how to use SDI video output and how to use IP video output.

12
Use SDI video output
Starting the Camera
After you have mounted the camera properly, connect the camera to power.
Each time the camera is powered on, it will perform a self-test to check the Pan/Tilt/Zoom (PTZ function). After self-test,
you can operate the camera.
NOTE!
The self-test process starts after the camera is powered up. Please wait patiently.
When the operating temperature is lower than zero degrees Celsius, the camera will be automatically pre-heat (the
pre-heat process takes 30 minutes at most). The self-test starts only after the temperature rises above zero degrees
Celsius.
Connect Camera to Monitor/SDI Device
To view your camera, you need to use the coaxial cable to connect your camera to monitor or SDI device.
* The monitor/device must support the signal of HD-SDI or 3G-SDI.
Connect Camera with Controller
To control and configure your camera, you need to connect with control system (or control keyboard) by RS-485.
1. Connection
To control and configure your camera, you need to connect with control system (or control keyboard) for communication
by RS-485/RS422. Set up the protocol of communication by control keyboard, the camera can auto detect VISCA and
PELCO-D.
1. Connection
1.1 RS485 (PELCO D) control connection diagram
Connect the Camera’s RS485+ and RS485 to RS485/TX+ and RS485/TX- on the control system/keyboard. The identity of
the control system or equipment may be different; the corresponding relationship is as follows:
RS-485 A
RX+
RS-485 D+
RS-485 +
RS-485 B
RX-
RS-485 D-
RS-485 -
1.2 RS422 (VISCA) control connection diagram
SONY Keyboard RS422 Connection

13
VISCA (None-Sony) Keyboard RS422 Connection
2. Setup Camera ID, Baud Rate and Control Protocol
In order for you to control a camera, the camera ID, baud rate and control protocol have to be set up in advance,
Baud rate and the camera ID setting on the camera have to be the same as baud rate and camera ID setting on the
system/control keyboard. The camera can auto detect the VISCA and PELCO-D, only need to set up the camera address
and baud rate.
Connect the camera to a monitor. There is an initial setting page displaying on the screen for 5 seconds when the camera is
powered on. On the page, it shows the factory default setting of the camera ID, baud rate and other information. Suggest
taking a picture of this default setting information for setting keyboard use. Set the keyboard or control system to match
the camera ID, baud rate setting with the camera.
1. Camera supports VISCA and PELCO-D protocols, protocol is detected automatically by the camera.
2. Factory Default Setting: For both SDI and IP video, Baud Rate: 9600, Camera ID: 001, Pelco Protocol.
3. Use RS485 Pelco-D can control up to 255 cameras, camera ID from 001 to 255 has to be set.
4. Use RS422 VISCA protocol can control up to 7 cameras, camera ID from 1 to 7 has to be set.
5. Supports baud rate of 2400bps, 4800bps, 9600bps and 38400bps.
6. How to set up the address and baud rate of the camera for SDI, please see the Page19.
7. On the keyboard side, for RS485 control, go into the camera setting menu, select the camera address/ID you want
to set up for, set the baud rate to match the same as the one has been set on camera side, select protocol Pelco D
for RS485 control. (How to set up the menu of the keyboard, please refer to the instruction of the keyboard you
are using.)
8. On the keyboard side, for VISCA control, select RS232/RS422 control
method, set the baud rate to match the same as the one has been set on
camera side. (How to set up the VISCA keyboard, please refer to the
instruction of the keyboard you are using.)
9. On IP control side, go into the camera IP web interface setting page by using
browser to login camera IP address (Default set to 192.168.0.13), go to
“SetupSystemPort&Devices” setting page, set the Baud Rate, camera
ID, Protocol to the same as the ones that have been set on the camera side.
(For detail, please refer to Part Two: Network Camera User Manual Page
25.)
10. SDI and IP video setting have to be matching with each other, if you change
any one of the settings on any sides of the SDI or IP.
NOTE!
Regarding the camera ID and Baud Rate setting, for the first communication setting, you must match the
control system (or keyboard) camera ID and Baud Rate setting to the cameras.
After communicating successfully in between the camera and the control, you can modify the ID and baud rate
of the camera using the keyboard.

14
Controlling the Camera
The operation of the control systems or devices of different makers may be different. To operate the camera, please refer
to the manual of the control system or the device.
Adjusting and Setting with Menus
About On-Screen Menus
You can change various settings, such as shooting conditions and system setup of the camera, while observing menus
displayed on a connected computer screen.
This section explains how to read the on-screen menus before starting menu operations.
The menu parameters may vary according to the different product model numbers.
For a complete configurations menu, see “Menu Configuration”.
NOTE!
You cannot perform pan/tilt operations while the menu is displayed.
How to adjusting and setting by joystick of keyboard
1. Push the joystick of the keyboard to the up or down: To select the menu that you
want.
2. Push the joystick of the keyboard to the right: To enter the menu that you want.
3. Push the joystick of the keyboard to the right: To confirm the value that you want to
set to.
Run preset 95th using keyboard to call/display the On-Screen Menu, the main menu will
display on the screen.
How to run presets of cameras, please refer to the manual of the keyboard/control system that
you are using.

15
The On-Screen Menu Configuration
95 Preset EXPOSURE AE MODE FULL AUTO
IRIS PRI CLOSE, F14, F11, F9.6, F8.0, F6.8, F5.6, F4.8, F4.0, F3.4, F2.8, F2.4, F2.0, F1.6
SHUTTER
1/1, 1/2, 1/3, 1/6, 1/12, 1/25, 1/50, 1/75, 1/100, 1/120, 1/150, 1/215, 1/300, 1/425,
1/600, 1/1000, 1/1250, 1/1750, 1/2500, 1/3500, 1/6000, 1/10000 s
BRIGHT 0-23
MANUAL GAIN -3, 0, 3, 9, 15, 18 dB
SPEED
1/1, 1/2, 1/3, 1/6, 1/12, 1/25, 1/50, 1/75, 1/100, 1/120, 1/150, 1/215, 1/300, 1/425,
1/600, 1/1000, 1/1250, 1/1750, 1/2500, 1/3500, 1/6000, 1/10000 s
IRIS CLOSE, F14, F11, F9.6, F8.0, F6.8, F5.6, F4.8, F4.0, F3.4, F2.8, F2.4, F2.0, F1.6
BACKLIGHT MODE 0~23
WIDE-D OFF , ON
DEFOG OFF , ON
AUTO SLOW SHUTTER OFF , ON
EX-COMP OFF , ON
ON LEVEL –10.5, –9, –7.5, –6, –4.5, –3, –1.5, 0, +1.5, +3, +4.5, +6, +7.5, +9, +10.5
EXIT
WHITE BALANCE AWB MODE AUTO
INDOOR
OUTDOOR
OPW
ATW
USER R GAIN 0-255
B GAIN 0-255
EXIT
PICTURE APERTURE 0-15
EFFECT OFF , B&W, NEG
EXIT
LENS PARAMETERS DIGITAL ZOOM OFF, ON
JOYSTICK RECOVER NONE , AF-AI, A/I, A/F
A/F RECOVER 0-255
A/I RECOVER 0-255
FOCUS NEAR LIMIT 1cm, 10cm, 20cm, 30m
DAY/NITE MODE AUTO , DAY, NITE
AUTO ICR THRESHOLD 0-28
GAMMA AUTO, NORMAL, 1-5
ZOOM SPEED 1~8
PRESET SPEED 0~255
EXIT
SYSTEM SETUP FACTORY DEFAULT
DISPLAY CONFIGURATION ZOOM LENS POSITION OFF , ON
DIRECTION INDICATOR OFF , ON
INTERFACE SET CAMERA ID 001-255
BAUD RATE 2400, 4800, 9600, 19200
EXIT
FLIP OFF, ON
SDI VIDEO 1080p:60/59.94/50/30/29.97/25 ; 1080i:50/60/59.94 ; 720p:60/59.94/50/30/25
IP VIDEO 720P,1080P
PROPORTIONAL PT OFF, ON
SET NORTH MOVE TO NORTH DIR, CALL PRESET 1 TO END
INTERFACE SET CAMERA ID 001-255
BAUD RATE 2400, 4800, 9600, 19200
SYSTEM RESET
EXIT

16
When the camera runs with Pelco-D protocol, Call preset 95 to enter the On-Screen Menu by using control keyboard, the
main menu will display on the screen.
When the camera runs with VISCA protocol, press [menu] button on VISCA control keyboard to enter the OSD Menu.
EXPOSURE Menu
The EXPOSURE menu is used to set the items related to exposure.
AE MODE (Exposure Mode)
FULL AUTO: The exposure is adjusted automatically using the sensitivity, electronic shutter speed, and iris.
BRIGHT: Adjust the brightness level (LEVEL) manually.
SHUTTER: Shutter mode. The exposure is adjusted automatically using the sensitivity and iris. Adjust the electronic
shutter speed (SPEED) manually.
IRIS PRI: Iris Priority mode. The exposure is adjusted automatically using the sensitivity and electronic shutter speed.
Adjust the iris (IRIS) manually.
MANUAL: Adjust the sensitivity (GAIN), electronic shutter speed (SPEED) and iris (IRIS) manually.
When you select one from various exposure modes, some of the following setting items that are required for the selected
mode appear.
GAIN: Select the gain from the following: -3, 0, 3, 9, 15, 18 dB
SPEED: Select the electronic shutter speed from the following: 1/1, 1/2,
1/3, 1/6, 1/12, 1/25, 1/50, 1/75, 1/100, 1/120, 1/150, 1/215, 1/300, 1/425,
1/600, 1/1000, 1/1250, 1/1750, 1/2500, 1/3500, 1/6000, 1/10000 sec.
IRIS: Select the iris the following: CLOSE, F14, F11, F9.6, F8.0, F6.8,
F5.6, F4.8, F4.0, F3.4, F2.8, F2.4, F2.0, F1.6
LEVEL: Select the brightness level from 0 to 23.
BACKLIGHT MODE:
When the background of the subject is too bright, or when the subject is too dark due to shooting in the AE mode, back
light compensation will make the subject appear clearer.
This is set to ON, OFF.
FUNCTION SETTING PRESET SETUP PRESET NUMBER 001-256
SET NEW PRESET
DELETE PRESET
EXIT
TOUR SETUP SEQUENCE NUMBER 1-4
DEFAULT DWELL 003-255
EDIT SEQUENCE
RUN CONTIONOUSLY
EXIT
PATTERN SETUP PATTERN NUMBER 1-4
RECORD NEW PATTERN 003-255
RUN CONTIONOUSLY
EXIT
SCAN SETUP PANNING NUMBER 1-4
SET LEFT LIMIT
SET RIGHT LIMIT
DEFAULT SPEED 003-255
RUN CONTIONOUSLY
EXIT
IDLE TIMER 0-255
IDLE ACTION OFF, PRE1-220, SCAN1-4, TOUR1-4, PATT1-4
P/Z SPEED 0~5
PRESET SPEED 0~5
EXIT
EXIT
〉EXPOSURE
WHITE BALANCE
PICTURE
LENS PARAMETERS
SYSTEM SETUP
FUNCTION SETTING
SAVE AND EXIT
EXIT
AE MODE: FULL ATUO
IRIS: N/A
GAIN: N/A
SHUTTER: N/A
BRIGHT: N/A
WIDE-D: OFF
DEFOG: OFF
AUTO SLOW SHUTTER: OFF
EX-COMP MODE: ON
EX-COMP LEVEL: 0dB
EXIT

17
WIDE-D (Wide dynamic range mode):
Wide Dynamic: ON, OFF. The camera distinguishes light and dark areas within the same scene, adjusts the brightness for
dark areas, and also controls the blown out highlights.
You can select the wide dynamic range mode between ON and OFF.
DEFOG:
Defog: ON, OFF. If the shooting scene has fog, you can open the defog function to improve the penetration of the image.
AUTO SLOW SHUTTER:
Auto slow shutter: ON, OFF. When AUTO SLOW SHUTTER is set to on, it can auto adjust the electronic shutter speed.
EX-COMP (Exposure Compensation):
When MODE is set to one of FULL AUTO, SHUTTER PRI or IRIS PRI, set this item to ON to enable exposure
compensation. When you set EX-COMP to ON, LEVEL appear and you can select the exposure compensation level from
the following:
-10.5, -9, -7.5, -6, -4.5, -3, -1.5, 0, +1.5, +3, +4.5, +6, +7.5, +9, +10.5
If you set the level to 0, exposure compensation will be disabled. Level +10.5 is the brightest and –10.5 is the darkest
compensation value.
When EX-COMP is set to OFF, exposure compensation does not function.
EXIT: Push the joystick to the right to exit this level menu.
WHITE BALANCE Menu
The WHITE BALANCE menu is used to select the white balance mode.
MODE (white balance mode):
Select the white balance mode from the following: AUTO, IN DOOR, OUT DOOR, OPW (One Push White Balance),
ATW (Auto Tracing White Balance), USER.
When you select USER, R. GAIN (red gain) and B. GAIN (blue gain) appear. You can select each item in the range from
0 to 255.
EXIT
Push the joystick to the right to exit this level menu.
PICTURE Menu
The PICTURE menu is used to set the items related to the picture.
APERTURE: The aperture is used to adjust the picture edge sharpness.
The value of the aperture is high, the edge of the picture more clearly, the value is
low, more blurred. Select the aperture from the following: 0 - 15.
EFFECT: (Picture Effect)
It consists of the following functions:
Neg. Art: Negative/Positive Reversal
Black & White: Monochrome Image
Image effect from Off, B&W, NEG.ART
EXIT: Push the joystick to the right to exit this level menu.
LENS PARAMETERS Menu
The LENS PARAMETERS menu is used to set the items related to the lens.
DIGITAL ZOOM:
Digital zoom: ON, OFF. When DIGITAL ZOOM is set to on, it can use the digital
zoom.
JOYSTICK RECOVER:
EXPOSURE
〉WHITE BALANCE
PICTURE
LENS PARAMETERS
SYSTEM SETUP
FUNCTION SETTING
EXIT
MODE: AUTO
USER DEFINED R: 203
USER DEFINED B: 213
EXIT
EXPOSURE
WHITE BALANCE
〉PICTURE
LENS PARAMETERS
SYSTEM SETUP
FUNCTION SETTING
EXIT
APERTURE：8
EFFECT ：OFF
EXIT
EXPOSURE
WHITE BALANCE
PICTURE
〉LENS PARAMETERS
SYSTEM SETUP
FUNCTION SETTING
EXIT

18
NONE: No effect.
A/F: After operating the camera, the mode of focus be changed to auto form
manual.
A/I: After operate the camera, the mode of IRIS be changed to auto form
manual.
AF-AI: After operate the camera, the mode of focus be changed to auto form
manual, and, the mode of IRIS be changed to auto form manual.
A/F RECOVER TIME:
When the camera is not in operation, if in the manual focus mode, after the A/F
RECOVER TIME, it will automatically transfer to the automatic focus.
If the time is 0, then the function is closed.
A/I RECOVER TIME:
When the camera is not in operation, if in the manual Iris mode, after the A/I RECOVER TIME, it will automatically
transfer to the automatic Iris.
If the time is 0, then the function is closed.
FOCUS NEAR LIMIT:
The near limit from the following: 1cm, 11cm, 30cm, 0.8m, 1.2m, 1.4m, 1.65m, 2.0m, 2.5m, 3.1m, 4.2m, 6.0m, 10m, 20m.
DAY/NITE MODE:
You can select the mode from AUTO, DAY and NIGHT.
When the camera is set to AUTO mode, the camera will automatically turn from Day mode (Color) to Night mode
(Black & White) when the lighting condition is low enough, the camera illuminator will be turned on automatically
at Night mode.
When the camera is set to Day mode, the camera will stay in Day mode (Color) no matter how low the lighting
condition is, the camera illuminator will not be turned on at Night. The image may be too dark to be seen in a low
light condition.
When the camera is set to Night mode, the camera will stay in Night mode (Black & White) no matter how bright
the lighting condition is, the camera illuminator will be turned on all the time. The image will be stay in Black &
White.
AUTO ICR THRESHOLD:
Set AUTO ICR THRESHOLD value to from 0 to 15 (The sensitivity from low to high).
GAMMA:
The gamma can be set to Auto, Manual, and value from 0 to 4.
ZOOMING SPEED:
The gamma can be set to value from 1 to 8.
PRESET SPEED:
The gamma can be set to value from 1 to 255.
EXIT: Push the joystick to the right to exit this level menu.
SYSTEM SETUP Menu
The SYSTEM SETUP menu is used to set the items related to the camera system.
FACTORY DEFAULT:
The menu is used to restore the factory settings.
DISPLAY CONFIGURATION:
Entered the menu of DISPLAY CONFIGURATION, it will be shown the below
items: ZOOM LENSPOSITION:
Select ON to display the zoom lens position on the screen.
DIRECTION INDICATOR:
Select ON to display the direction indicator on the screen.
DIGITAL ZOOM: OFF
JOYSTICK RECOVER：NONE
A/F RECOVER TIME: 000
A/I PECOVER TIME: 000
FOCUS NEAR IMIT: 30CM
DAY/NITE MODE: NITE
AUTO ICR HRESHOLD: 28
GAMMA: NORMAL
ZOOMING SPEED: 8
PRESET SPEED: 255
EXIT
EXPOSURE
WHITE BALANCE
PICTURE
LENS PARAMETERS
〉SYSTEM SETUP
FUNCTION SETTING
EXIT
FACTORY DEFAULT
DISPLAY CONFIGURATION
〉INTERFACE SET
FLIP: OFF
SDI VIDEO: 1080P30
IP VIDEO : 1080P
PROPORTIONAL PT: ON
SET NORTH
SYSTEM INFO
SYSTEM RESET
EXIT

19
INTERFACE SET:
This menu is used to set the following parameters:
CAMERA ID:
Factory Default Setting: 001
Use RS485 Pelco-D can control up to 255 cameras, camera ID from 001 to
255 has to be set.
Use RS422 VISCA protocol can control up to 7 cameras, camera ID from 1
to 7 has to be set.
BAUD RATE:
Factory Default Setting: 9600,
Select the baud rate from the following: 2400, 4800, 9600, 38400bps.
NOTE!
After the camera ID and Baud rate is set, to activate the new set camera ID and Baud rate, the camera has
to be rebooted by powering the camera OFF and ON.
For Dual-Output camera, the camera ID and Baud rate on IP web interface has to be set to the same ID as
the camera’s for IP control. (See user manual Part Two)
You may need to reboot the keyboard after you change the camera ID and Baud rate.
Once modified and saved the camera ID and baud rate, please modify the corresponding parameters on both
the keyboard and IP web interface setting, otherwise the camera and keyboard and IP control will be unable to
communicate.
FLIP:
Select ON to flip the image if you need to lift the camera.
VIDEO FORMAT:
SDI + IP True Dual Output: You can have parallel SDI and IP video output. Either SDI or IP video format can be set up
independently for having dual output simultaneously.
SDI output: Select the SDI video output format from the following:
B Class models: 1080P: 60/59.94/50/30/29.97/25; 1080I:60/59.94/50; 720P: 60/50/30/25.
S Class models: 1080P: 60/50/30/25; 720P: 60/50/30/25.
IP output: Select the IP video output format from the following:
1080P:30/25, 720P:30/25
Follow the steps to change the video format:
1. Set SDI video resolution in SYSTEM SETUP.
2. Select the SDI VIDEO format you want to have from 1080P: 60/59.94/50/30/29.97/25; 1080I:60/59.94/50; 720P:
60/50/30/25.
3. Waiting for a while for camera new set video format being taken. It is normal that you cannot take the control of
the interface while the video format is being changed. You can reboot the camera by powering OFF and ON to
active the new set video format if it takes too long to complete the format changing by itself.
4. Go to IP camera Web Interface (Refer to PART TWO-Network Cameras User Manual), you can set IP video
resolution to following: 1080P30, 1080P25, 720P30, 720P25.
PROPORTIONAL PT:
Proportional pan automatically reduces or increases the pan and tilt speeds in proportion to the amount of zoom. At
telephoto zoom settings, the pan and tilt speeds will be slower for a given amount of joystick deflection than at wide zoom
settings. This keeps the image from moving too fast on the monitor when there is a large amount of zoom.
Select ON: The bigger the camera lens is zoomed in, the slower the speed of Pan and Tilt would be. The smaller the
camera lens is zoomed out, the faster the speed of Pan and Tilt would be.
Select OFF: No matter how the lens ratio changes, the speed of Pan and Tilt is set to the fastest.
SET NORTH:
Select ON to open this function.
CAMERA ID: 001
BAUD RATE: 9600
EXIT

20
Turn the camera to the north, and then save it by call preset 1.
SYSTEM INFO:
CAMERA ID: Modify in the menu of “INTERFACE SET”.
BAUD RATE: Modify in the menu of “INTERFACE SET”.
SDI VIDEO: Modify in the menu of “INTERFACE SET”.
IP VIDEO: Modify in the menu of “INTERFACE SET”
VERSION: The version of the software.
SYSTEM RESET:
To save the changes have been made and make the changes activated.
EXIT: Push the joystick to the right to exit this level menu.
FUNCTION SETTING Menu
The FUNCTION SETTING menu is used to set the items related to the camera functionalities.
Note: The number of available presets may be limited by the head-ins, controllers, and DVRs that are connected to your
dome system.
PRESETS SETUP:
Preset is to store the PTZ information (such as: Pan and Tilt positions, focal length
etc.) under the specific condition, and call the camera PTZ quickly to shoot to the
specified location that you want the camera to move to.
Note: Presets not only save desired image positions, various picture settings such as
brightness, exposure values and other variables are also saved and stored.
The menu is used to manage the presets. Total of 220 presets can be managed.
PRESETS NUMBER:
The current preset number that you are managing.
SET NEW PRESET:
To set up the preset of the above preset number.
1. Push the joystick to the right to enter this setting menu, you will see “call preset 1 to end”.
2. Adjust the camera to the position that you want the camera to be, and then
call the preset 1 using the keyboard to save the position to be the current
preset.
3. Finished.
DELETE PRESET:
Delete the above preset.
1. Push the joystick to the right to delete this preset.
2. Finished.
EXIT: Push the joystick to the right to exit this level menu.
In order to use the special functions of the camera, the following presets are predefined for specific functions (You can
find the default predefined preset at Web interface, Setup -> PTZ -> Advanced Settings):
Preset number
Set / call
Function description
54
Set
Lens Reset
55
Call
Open back light
Set
Close back light
56
Call
Open auto shutter
Set
Close auto shutter
57
Call
Open screen display
Set
Close screen display
58
Call
Open Digital Zoom
Set
Close Digital Zoom
59
Call
Disable WDR
Set
Enable WDR
60
Call
Auto Iris
Set
Manual Iris
61
Call
Auto white balance
CAMERA ID ：001
BAUD RATE ：9600
SDI VIDEO ：1080P/30
IP VIDEO ：1080P
SVS0I0200S010801B09
EXPOSURE
WHITE BALANCE
PICTURE
LENS PARAMETERS
SYSTEM SETUP
〉FUNCTION SETTING
EXIT
PRESETS SETUP
TOUR SETUP
PATTERN SETUP
SCAN SETUP
IDLE TIMER ：003
IDLE ACTION ：OFF
EXIT