Bolin Technology VCC-8HD20S-2SMC User manual

1
8 Series HD PTZ Camera
USER MANUAL
VERSION: VCC-8HD-M-11142018
VCC-8HD20S-2SMC
VCC-8HD30S-2SMC
© 2018 Bolin Technology

2
Contents
IMPORTANT INFORMATION ..................................................................................................................................................... 3
WHAT’S IN THE BOX ................................................................................................................................................................. 5
OVERVIEW................................................................................................................................................................................ 6
CAMERA VERSION.............................................................................................................................................................................. 6
MODEL NUMBERS ............................................................................................................................................................................. 6
FEATURES ........................................................................................................................................................................................ 6
CAMERA DIAGRAMS................................................................................................................................................................. 7
CAMERA .......................................................................................................................................................................................... 7
REMOTE CONTROLLER ........................................................................................................................................................................ 8
3V CR2032 COIN LITHIUM BATTERY INSTALLATION:................................................................................................................................ 8
1. FIND THE BATTERY COMPARTMENT ON THE BOTTOM OF THE REMOTE CONTROLLER................................................................................ 8
2. USE A CROSS SCREWDRIVER TO UNSCREW,WITH A NEEDLE,PRESS AND SLIDE THE BATTERY TRAY OUT ........................................................ 8
3. REMOVE THE OLD BATTERY. ........................................................................................................................................................ 8
4. WITH THE POSITIVE SIDE FACING UP TOWARD YOU,PUT IN THE CR2032 BATTERY................................................................................. 8
5. SLIDE THE BATTERY BACK INTO THE CONTROLLER. ............................................................................................................................ 8
SYSTEM CONFIGURATION......................................................................................................................................................... 9
CONNECTION.................................................................................................................................................................................... 9
OBTAIN VIDEO SIGNAL ..................................................................................................................................................................... 10
CAMERA CONTROL METHODS AND SYSTEM CONFIGURATIONS ................................................................................................................. 11
BOTTOM DIP SWITCH SETTINGS ............................................................................................................................................. 15
ADJUSTING AND SETTING WITH MENUS................................................................................................................................. 17
EXPOSURE MENU ......................................................................................................................................................................... 18
WHITE BALANCE MENU................................................................................................................................................................ 18
PICTURE MENU............................................................................................................................................................................. 19
PAN TILT ZOOM MENU................................................................................................................................................................. 19
SYSTEM MENU.............................................................................................................................................................................. 19
OPERATION USING THE INFRARED REMOTE CONTROLLER ..................................................................................................... 21
PAN/TILT AND ZOOM OPERATION ...................................................................................................................................................... 21
OPERATING MULTIPLE CAMERAS WITH THE INFRARED REMOTE CONTROLLER.............................................................................................. 22
ADJUSTING THE CAMERA................................................................................................................................................................... 22
STORING THE CAMERA SETTINGS IN MEMORY —THE PRESETTINGFEATURE ............................................................................................... 23
MENU CONFIGURATION ......................................................................................................................................................... 24
DIMENSION ............................................................................................................................................................................ 25
SPECIFICATIONS...................................................................................................................................................................... 26

3
Operating Instructions
Thank you for purchasing our product. If there are any questions, please contact the authorized dealer.
Before operating the unit, please read this manualthoroughly and retain it for future reference.
Copyright
Copyright 2015-2016 Bolin Technology all rights reserved. No part of this manual may be copied, reproduced,
translated, or distributed in any form or by any means without prior consent in writing from our company.
Trademark Acknowledgement
and other Bolin's trademarks and logos are the property of Bolin Technology. Other trademarks,
company names and product names contained in this manual are the property of their respective owners.
Trademarks and Registered Trademarks Acknowledgement
Microsoft, Windows, ActiveX, and Internet Explorer are registered trademarks of Microsoft Corporation in
the U.S. and/or other countries.
HDMI, the HDMI logo and High-Definition Multimedia Interface are the trademarks or registered
trademarks of HDMI Licensing, LLC in the United States and other countries.
The Software may contain h.264/AVC video technology, the use of which requires the following notice from
MPEG-LA, L.L.C.:
THIS SOFTWARE IS LICENSED UNDER THE AVC PATENT PORTFOLIO LICENSE FOR THE PERSONAL AND
NON-COMMERCIAL USE OF A CONSUMER TO (I) ENCODE VIDEO IN COMPLIANCE WITH THE AVC
STANDARD ("AVC VIDEO") AND/OR (II) DECODE AVC VIDEO THAT WAS ENCODED BY A CONSUMER
ENGAGED IN A PERSONAL AND NON-COMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO
PROVIDER LICENSED TO PROVIDE AVC VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR
ANY OTHER USE. ADDITIONAL INFORMATION MAY BE OBTAINED FROM MPEG LA, L.L.C. SEE
http://www.mpegla.com.
HEVC/h.265 Covered by one or more claims of patents listed at patentlist.hevcadvance.com
HDBaseT is a trademark of the HDBaseT Alliance.
ONVIF trademarks and logos are to be used per the guidelines established in this and other ONVIF policies
and documents including the ONVIF Rules of Membership and the ONVIF Logo Guidelines1.
Other trademarks, company names and product names contained in this manual are the property of their
respective owners.
IMPORTANT INFORMATION
Legal Notice
Attention:
To ensure account security, please change the password after your first login. You are recommended to set a strong
password (no less than eightcharacters).
The contents of this document are subject to change without prior notice. Updates will be added to the new version of this
manual. We will readily improve or update the products or procedures described in the manual.
Best effort has been made to verify the integrity and correctness of the contents in this document, but no statement, information,
or recommendation in this manual shall constitute formal guarantee of any kind, expressed or implied. We shall not be held
responsible for any technical or typographical errors in this manual.
The product appearance shown in this manual is for reference only and may be different from the actual appearance of your
device.
This manual is a guide for multiple product models and so it is not intended for any specific product.
Due to uncertainties such as physical environment, discrepancy may exist between the actual values and reference values

4
provided in this manual.
Use of this document and the subsequent results shall be entirely on the user’s own responsibility.
Safety Information
WARNING!
Installation and removal of the unit and its accessories must be carried out by qualified personnel. You must read all of
the Safety Instructions supplied with your equipment before installation andoperation.
Warnings:
If the product does not work properly, please contact your dealer. Never attempt to disassemble the camera yourself.
(We will not assume any responsibility for problems caused by unauthorized repair or maintenance.)
This installation should be made by a qualified service person and should conform to all the local codes.
When shipping, the camera should be packed in its originalpackaging.
Make sure the power supply voltage is correct before using the camera.
Do not drop the camera or subject it to physicalshock.
Do not touch sensor modules with fingers. If cleaning is necessary, use a clean cloth with a bit of ethanol and wipe it
gently. If the camera will not be used for an extended period of time, put on the lens cap to protect the sensor from dirt.
Do not aim the camera lens at the strong light such as sun or incandescent lamp. The strong light can cause fatal
damage to the camera.
Maintenance Precautions:
If there is dust on the front glass surface, remove the dust gently using an oil-free brush or a rubber dust blowing
ball.
If there is grease or a dust stain on the front glass surface, clean the glass surface gently from the center outward
using anti-static gloves or an oil-free cloth. If the grease or the stain still cannot be removed, use anti-static
gloves or an oil-free cloth dipped with detergent and clean the glass surface gently until it is removed.
Do not use organic solvents, such as benzene or ethanol when cleaning the front glass surface.
Regulatory Compliance
FCC Part 15
This equipment has been tested and found to comply with the limits for digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his ownexpense.
This product complies with Part 15 of the FCC Rules. Operation is subject to the following twoconditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired operation.
LVD/EMC Directive
This product complies with the European Low Voltage Directive 2006/95/EC and EMC Directive
2004/108/EC.
WEEE Directive–2002/96/EC
The product this manual refers to is covered by the Waste Electrical & Electronic Equipment (WEEE)
Directive and must be disposed of in a responsible manner.

5
WHAT’S IN THE BOX
Accessories (Optional)

6
Overview
Camera Version
Hardware: HV:V.0C.0bdeijkl.02.00S.07.A01
Software：SV:V0C0100S050401A02 FCB-CV7320 (20X)
SV:V0C0100S090401A02 FCB-CV7520 (30X)
Model Numbers
This user guide is suitable for the following models:
VCC-8HD20S-2SMC
VCC-8HD30S-2SMC
Features
Resolution: 1080P,720P
Zoom: Optical 20X, 30X
Video Output: HDMI, 3G-SDI, CVBS
The camera can simultaneously have SDI, HDMI and CVBS video output
Power: DC 12V, HDBaseT PoE+(Not Activated)
±350-degree continuous pan, ±120-degree continuous tilt
128 presets, Speed up to 150 degrees/sec
Standard mounting and ceiling mounting with E-Flip function
IR remote control, RS-232 control, RS-422/485 control
You can use the infrared remote controller to set the camera and also to select panning, tilting and
zooming from the setting menu.
You can store up to 6 presets of camera directionand camera parameters into thecamera. (Up to 6
presets on remote controller or 128 presets via protocol programming.)

7
Camera Diagrams
Camera
1. 12V DC Power Port
Connect the supplied DC power adaptor and cord.
2. CVBS Video Output
3. Audio Input(Not Activated)
4. Audio Output(Not Activated)
5. RS232 Control Port
RJ45 to RS232 extension cable is provided.
6. RS-422 Control Port
RJ45 to RS422 extension cable is provided.
7. RJ45 Port for HDBaseT signal output(Not Activated)
8. IP Network RJ45 Port(Not Activated)
9. HDMI Port
HDMI 1.4
10. SDI Port
3G-SDI
11. Power LED Indicator
Turns green when the camera is connected to power outlet. When the power is turned on, it takes about 15 to 30
seconds to display the image after LED turns on.
12. Built-in Mic
13. IR Remote Controller Sensors
These are sensors to receive commands from infrared remote controller
14. Lens
This is a 20X/30X magnification optical zoomlens.
15. Communication LED Indicator
Flashes blue when the camera receives commands from the infrared remote controller.
16. Fix mounting holes
For original wall/ceiling mount bracket
17. Tripod mounting holes
18. Bottom DIP Switch

8
Remote Controller
1. Power
2. Camera ID (Total 3) Selector
3. Preset Position (Total 6) Calling and Setting
4. PAN-TILT
Pan and Tilt direction control
HOME: Home position, Resolution reset
5. L/R Direction Set
Left and right orientation setting
6. ZOOM/FOCUS
Far
Near
7. Auto/Manual Focus
8. Back Light
9. Video Format Switching
You can change the video format by keep
pressing the button.
10. MENU
On screen menu display ON/OFF
11. Audio Switch
You can turn the Mic built in the camera Off/ON by
pressing the button once.
12. Fast/Slow Zoom Switching
13. White Balance
Change the White Balance setting by pressing
the button.
14. De-Flicker
When you find the video flicking, press the button
once to eliminate the flickers.
Notes
3V CR2032 Coin lithium Battery is not included with remote controller, you should purchase it at your local market.
3V CR2032 Coin lithium batteries are not interchangeable.
3V CR2032 Coin lithium battery Installation:
1. Find the battery compartment on the bottom of the remote controller
2. Use a cross screwdriver to unscrew, with a needle, press and slide the battery tray out
3. Remove the old battery.
4. With the positive side facing up toward you, put in the CR2032 battery.
5. Slide the battery back into the controller.

9
System Configuration
Connection
In this connection configuration, HDMI cable, SDI video cable, CVBS video cable, Control cable is required. To obtain
these third party components or accessories, consult the dealer where you bought your camera.
Notes
Use only the AC power adaptor (JEITA type4) supplied with the unit. Do not use any other
AC power adaptor.
Polarity of the plug
You have to set the video format of the signal to output from the camera. For detailed informationon how to set
the video format, see “SYSTEM SELECT switch” on page 19 or 20.

10
Obtain Video Signal
The camera can simultaneously have HDMI, SDI and CVBS video output.
On this model, IP video and HDBaseT video are not activated.
HDMI HD Video signal
1. Connect the camera to a HD monitor/TV using HDMI cable.
2. Turn on the camera, video will display on the monitor after running initializing.
3. Information of the camera initial setting status will display for 5 seconds.
4. You can set the video format of the camera to the one you want to display. (How to set video format, see page
20)
SDI Video Signal
1. Connect SDI cable in between the camera your SDI Device/display.
2. You now have SDI video output.
CVBS Video Signal
1. Connect CVBS cable in between the camera and your CVBS Device/display.
2. You now have CVBS video output.
Camera Initial setting status Information
Information of the camera initial setting status will display for 5 seconds.
1. Camera PELCO ID for RS485 control
2. Camera ID for IR Remote Controller
3. IR remote control signal receive current setting
4. Baud Rate current setting
5. Control COMM Port current setting
6. Video format current setting
7. HDMI current setting
8. Model number
9. Firmware version