Bolin Technology EX1030BHD-L5NA User manual

1
EX1000 SERIES
IR LASER IP PTZ CAMERA
HD/4K/STARLIGHT
USER MANUAL
VERSION: EXIP-M-06112017
© 2017 Bolin Technology

2
Contents
PART ONE: PTZ CAMERA USER MANUAL ...........................................................................................................................................4
IMPORTANT INFORMATION ..............................................................................................................................................................4
OVERVIEW.........................................................................................................................................................................................7
FEATURES .................................................................................................................................................................................................7
WHAT’S IN THE BOX...............................................................................................................................................................................8
ACCESSORIES-OPTIONAL .............................................................................................................................................................................8
CAMERA DIAGRAMS..........................................................................................................................................................................9
TAIL-CABLE ......................................................................................................................................................................................10
INSTALLING YOUR CAMERA.............................................................................................................................................................12
CHECK CAMERA COMPONENTS AND INSTALLATION CONDITIONS .......................................................................................................................12
POWER INPUT..........................................................................................................................................................................................12
MOUNTING THE CAMERA...........................................................................................................................................................................14
LASER ILLUMINATOR .......................................................................................................................................................................14
STARTING THE CAMERA...................................................................................................................................................................15
SETTING CAMERA OVER THE LAN ................................................................................................................................................................15
ACCESSING YOUR CAMERA .........................................................................................................................................................................15
PART TWO: NETWORK CAMERA USER MANUAL .............................................................................................................................17
NETWORK CONNECTION .................................................................................................................................................................17
LOGIN..............................................................................................................................................................................................17
LOGGING IN TO THE WEB INTERFACE ..............................................................................................................................................19
INTRODUCTION TO THE WEB INTERFACE ........................................................................................................................................20
INITIAL CONFIGURATION ............................................................................................................................................................................20
CONFIGURING PARAMETERS...........................................................................................................................................................21
LOCAL PARAMETERS..................................................................................................................................................................................21
NETWORK CONFIGURATION............................................................................................................................................................22
TCP/IP ..................................................................................................................................................................................................22
PPPOE...................................................................................................................................................................................................23
DHCP....................................................................................................................................................................................................23
PORT .....................................................................................................................................................................................................23
IMAGE CONFIGURATION .................................................................................................................................................................25
IMAGE ADJUSTMENT.................................................................................................................................................................................25
AUDIO AND VIDEO CONFIGURATION ..............................................................................................................................................33
VIDEO CONFIGURATION.............................................................................................................................................................................33
VIDEO FORMAT........................................................................................................................................................................................34
VIDEO COMPRESSION................................................................................................................................................................................35
AUDIO CONFIGURATION ............................................................................................................................................................................35
ROI .......................................................................................................................................................................................................35
MEDIA STREAM CONFIGURATION ................................................................................................................................................................36
ALARM CONFIGURATION ................................................................................................................................................................37
CONFIGURING MOTION DETECTION ALARM ..................................................................................................................................................37
MEMORY CARD STORAGE ..........................................................................................................................................................................41
SYSTEM MAINTENANCE ..................................................................................................................................................................42
SECURITY ................................................................................................................................................................................................42

3
SETTING THE SYSTEM TIME.........................................................................................................................................................................44
SETTING SERVERS .....................................................................................................................................................................................44
SERIAL PORT MODE CONFIGURATION...........................................................................................................................................................45
MAINTENANCE................................................................................................................................................................................48
UPGRADING THE DEVICE............................................................................................................................................................................48
RESTARTING THE SYSTEM ...........................................................................................................................................................................48
IMPORTING AND EXPORTING SYSTEM CONFIGURATION FILE..............................................................................................................................48
COLLECTING DIAGNOSTIC INFORMATION.......................................................................................................................................................49
DIGITAL ZOOM &FOCUS CONFIGURATION ....................................................................................................................................................49
LIVE VIEW........................................................................................................................................................................................50
LIVE VIEW TOOLBAR .................................................................................................................................................................................51
VIEWING CERTAIN AREA OF IMAGES.............................................................................................................................................................52
USING 3D POSITIONING ............................................................................................................................................................................52
VIDEO PLAYBACK AND DOWNLOAD WITH EDGE STORAGE .............................................................................................................52
PTZ CONTROL ..................................................................................................................................................................................53
SETTING PATROL BY PRESETS ......................................................................................................................................................................54
APPENDIX A GLOSSARY ...................................................................................................................................................................58
SPECIFICATIONS........................................................................................................................................................................................59
DIMENSIONS ...................................................................................................................................................................................62
MODEL:BL-PP80 (80W POEPOWER INJECTOR)...........................................................................................................................................64

4
Part One: PTZ Camera User Manual
Operating Instructions
Thank you for purchasing our product. If there are any questions, please contact the authorized dealer.
Before operating the unit, please read this manualthoroughly and retain it for futurereference.
Copyright
Copyright 2015-2016 Bolin Technology all rights reserved. No part of this manual may be copied, reproduced,
translated, or distributed in any form or by any means without prior consent in writing from our company.
Trademark Acknowledgement
and other Bolin's trademarks and logos are the property of Bolin Technology. Other trademarks, company
names and product names contained in this manual are the property of their respective owners.
IMPORTANT INFORMATION
Legal Notice
Attention:
To ensure account security, please change the password after your first login. You are recommended to set a strong password
(no less than eightcharacters).
The contents of this document are subject to change without prior notice. Updates will be added to the new version of this manual.
We will readily improve or update the products or procedures described in the manual.
Best effort has been made to verify the integrity and correctness of the contents in this document, but no statement, information, or
recommendation in this manual shall constitute formal guarantee of any kind, expressed or implied. We shall not be held responsible
for any technical or typographical errors in thismanual.
The product appearance shown in this manual is for reference only and may be different from the actual appearance of your device.
This manual is a guide for multiple product models and so it is not intended for any specific product.
In this manual, the illustrations of displayed interface, parameters displayed, drawings and value ranges may vary with models.
Please see the actual product for details.
Due to uncertainties such as physical environment, discrepancy may exist between the actual values and reference values provided in
this manual.
Use of this document and the subsequent results shall be entirely on the user’s own responsibility.
Disclaimer
CAUTION!
The default password is used for your first login. To ensure account security, please change the password after your
first login. You are recommended to set a strong password (no less than eight characters).
 To the maximum extent permitted by applicable law, the product described, with its hardware, software,
firmware and documents, is provided on an “as is”basis.
 Best effort has been made to verify the integrity and correctness of the contents in this manual, but no
statement, information, or recommendation in this manual shall constitute formal guarantee of any kind,
expressed or implied. We shall not be held responsible for any technical or typographical errors in this

5
manual. The contents of this manual are subject to change without prior notice. Update will be added to
the new version of this manual.
 Use of this manual and the subsequent result shall be entirely on the user’s own responsibility. In no event
shall we be liable to you for any special, consequential, incidental, or indirect damages, including, among
others, damages for loss of business profits, business interruption, or loss of data or documentation in
connection with the use of thisproduct.
 Video and audio surveillance can be regulated by laws that vary from country to country. Check the law in
your local region before using this product for surveillance purposes. We shall not be held responsible for
any consequences resulting from illegal operations of the device.
 The illustrations in this manual are for reference only and may vary depending on the version or model. The
screenshots in this manual may have been customized to meet specific requirements and user preferences.
As a result, some of the examples and functions featured may differ from those displayed on your monitor.
 This manual is a guide for multiple product models and so it is not intended for any specific product.
 Due to uncertainties such as physical environment, discrepancy may exist between the actual values and
reference values provided in this manual. The ultimate right to interpretation resides in our company.
Environmental Protection
This product has been designed to comply with the requirements on environmental protection. For the proper storage,
use and disposal of this product, national laws and regulations must be observed.
Symbols
The symbols in the following table may be found in this manual. Carefully follow the instructions indicated by the
symbols to avoid hazardous situations and use the product properly.
WARNING!: Indicates a hazardous situation which, if not avoided, could result in bodily injury or death.
CAUTION!: Indicates a situation which, if not avoided, could result in damage, data loss or malfunction to product.
NOTE: Indicates useful or supplemental information about the use of product.
Safety Information
WARNING!
Installation and removal of the unit and its accessories must be carried out by qualified personnel. You must read all
of the Safety Instructions supplied with your equipment before installation andoperation.
Warnings:
•If the product does not work properly, please contact your dealer. Never attempt to disassemble the camera yourself. (We
will not assume any responsibility for problems caused by unauthorized repair or maintenance.)
•This installation should be made by a qualified service person and should conform to all the local codes.
•When shipping, the camera should be packed in its originalpackaging.
•Make sure the power supply voltage is correct before using the camera.
•Do not drop the camera or subject it to physicalshock.
•Do not touch sensor modules with fingers. If cleaning is necessary, use a clean cloth with a bit of ethanol and wipe it gently.
If the camera will not be used for an extended period of time, put on the lens cap to protect the sensor from dirt.
•Do not aim the camera lens at the strong light such as sun or incandescent lamp. The strong light can cause fatal
damage to the camera.
•The sensor may be burned out by a laser beam, so when any laser equipment is being used, make sure that the surface
of the sensor not be exposed to the laser beam.

6
•Mount laser dome camera at a height of six meters (19.7 ft) from the ground. To
avoid bodily injury from the laser radiation, please make sure that no one is
within the range of three meters (9ft) from the camera when the laser is working.
•Never look at operating laser while the power is on.
•Caution: Use of controls or adjustments to the performance or procedures other
than those specified herein may result in hazardous laser emissions.
Maintenance Precautions:
•If there is dust on the front glass surface, remove the dust gently using an oil-free brush or a rubber dust blowing ball.
•If there is grease or a dust stain on the front glass surface, clean the glass surface gently from the center outward using
anti-static gloves or an oil-free cloth. If the grease or the stain still cannot be removed, use anti-static gloves or an oil-
free cloth dipped with detergent and clean the glass surface gently until it is removed.
•Do not use organic solvents, such as benzene or ethanol when cleaning the front glass surface.
Regulatory Compliance
FCC Part 15
This equipment has been tested and found to comply with the limits for digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
This product complies with Part 15 of the FCC Rules. Operation is subject to the following twoconditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired operation.
LVD/EMC Directive
This product complies with the European Low Voltage Directive 2006/95/EC and EMC Directive 2004/108/EC.
WEEE Directive–2002/96/EC
The product this manual refers to is covered by the Waste Electrical & Electronic Equipment (WEEE) Directive
and must be disposed of in a responsible manner.

7
Overview
This user guide is suitable for the following models:
S TYPE:
•EX1030BHD-L5NA (IP)
•EX1030BHD-L5NAP (IP, POE)
L TYPE:
•EX1022B4K-L5NA (IP)
•EX1022B4K-L5NAP (IP, POE)
•EX1022B4K-NF-L5NA (IP, Nitrogen)
•EX1022B4K-NF-L5NAP (IP, Nitrogen, POE)
•EX1020BHD-L5NXGA (IP)
•EX1020BHD-L5NXGAP (IP, POE)
•EX1020BHD-NF-L5NXGA (IP, Nitrogen)
•EX1020BHD-NF-L5NXGAP (IP, Nitrogen, POE)
Features
•Supports Various Resolutions: 12MP,4K(8MP), 6MP,5MP,3MP, 1080P, 720P (Model Specific)
•Supports Various Zoom: 20X, 22X, 30X
•Video Output: IP
•Supports ONVIF Profile S
•Video Compression: H.264/H.265, MJPEG
•ZDP- Zero Deviation Positioning technology for high accuracy.
•Adaptive IR laser illumination distance up to 500 Meters.
•Outdoor Environmental Rating: IP67
•Corrosion Resistant treatment, wind load durability: 60m/s
•Power Input: AC 24V. PoE 80W (Bolin PoE 80W Injector needed, optional).
•Various Image Functionalities: WDR, BLC, Defog, Day/Night
•Supports ±120°tilt / ±360°pan range, adaptive speed up to 90°/s
•Support 255 presets, adaptive speed: 80°/s
•Supports 3D Positioning Feature
•Supports Motion Detection, Guard Tour Presets: 4 Zones
•Supports Preset Time Task Activation: 8 Periods
•Supports 1 alarm input/output, 1 audio input/ output, RS-485 control (Not Activated), (Tail-Cable Type A)
•Nitrogen filled Housing (Optional)

8
WHAT’S IN THE BOX
Accessories- Optional

9
Camera Diagrams
Camera
1. IR Laser illuminator (See Page)
2. Lens
BL-PP80 80w PoE Power Injector (Optional)
1. Data/Power Output (Connect to the specific PoE camera, Power Comsumption:80w, port of speed:
100/1000Mbps adaptive)
2. Data in (Connect to network switch)
3. DC 48V Power Input Port
4. Power Indicator

10
Tail-Cable
All cables are tagged to indicate their functions separately. The cables available may vary with the product model. There are
two types of Tail-Cable available for EX1000 series PTZ camera.
1. Type A-Cable: Full function cable with audio and alarm
2. Type N-Cable: Only IP video out and Power
Cable Connection

11
Type N-Cable Connection
Type A-Cable Connection
NOTE:
•Use water proof / IP67 rated junction box/ connection box to protect the RJ45 and other connections. A water proof
RJ45 connector is available on some models.

12
Installing Your Camera
The following diagrams are for your reference only. See the actual product to mount your camera.
Check Camera Components and Installation Conditions
Before mounting your camera, check the device model number and included contents against the packing list to ensure
components are complete.
Camera Structure
1. Tail-Cable
2. Camera Body
Important
•Verify the bearing capacity of the mounted position
•Verify that the mounted position meets the bearing requirements. Otherwise, you
are advised to reinforce the mounted position for the device weight. For more
information, see the product datasheet.
•Verify lightning protection and grounding requirements
•Select proper lightning protection devices for the power supply, audio and video
signal interfaces, and RS485 interfaces.
•Ground the terminal properly.
Cable Requirements
Network Cable
10/100 Mbps Ethernet CAT 5/5E/6 UTP cables are applicable to the ANSI/EIA/TIA-568A/B and ISO/D.
Eight wires in the network cable need to be inserted in parallel into the top of the cable connector. The cable connector needs
to be crimped in position. When the cable connector is in position, ensure that the metal pieces of the cable connector are
parallel to each other and the clamp of the cable connector is intact.
Power Input
Bolin PTZ camera provides 24VAC power input
Power Cable
Data listed in Table 2-1 is applicable to copper cables that use 24 VAC/24 VDC power supply. The item Core Diameter
indicates the conductor diameter.
Power Loss on the Cable for Different Lengths and Different Core Diameters
Core Diameter
(Unit: mm)
Distance
(Unit: m)
Power (Unit: VA)
0.80
1.00
1.25
2.00
10
86
137
218
551
20
42
68
109
275
30
28
45
72
183
40
21
34
54
137
50
17
27
43
110
60
14
22
36
91

13
70
12
19
31
78
80
10
17
27
68
90
9
15
24
61
100
8
13
21
55
110
7
12
19
49
120
7
11
17
45
130
6
10
16
42
140
6
9
15
39
150
5
9
14
36
160
5
8
13
34
170
4
7
12
32
180
4
7
11
30
190
4
7
11
28
200
4
6
10
27
NOTE:
•Important: Power supply requirement is 24VAC 2.5 Amp to ensure proper functionality of PT motor and LED
illumination. Using power supply lower than 24VAC 2.5Amp will cause camera crashing or insatiability.
Power Connector: Phoenix Connector Description
1. The anode and the cathode are not distinguished for phoenix connectors of red and black cables.
2. GND: yellow-green color.
Note: GND is used to ground the camera. Ensure that GND is connected to a reliable grounding point.
PoE Power Injector
Other than 24VAC power input, Bolin PTZ camera provides PoE power as an optional power input.
For PoE power, you must use Bolin 80W Power PoE Injector: model BL-PP80. It provides nonstandard power up to the PTZ
camera. Connect this PoE injector to a network switch and then run Ethernet cable for data transmission and power up the PoE
PTZ camera (Specific model: EX1000 & SD500 Series) for distance up to 100 meters.
NOTE:
•Disconnect the power from the camera beforemounting.
•Accessories such as the wall mount bracket and the pendant mount bracket may be necessary during mounting. For their
model, refer to the accessory list recommended by your dealer.
•The wall bearing capacity and the bracket length must meet all onsite mounting requirements. You will need to select a
mount type based the actual environment.

14
Mounting the Camera
NOTE:
•When mounting the camera, please install the bracket adapter to the bracket first and then mount the camera to the
bracket.
•Tighten all the screws to hold the camera securely.
•For waterproofing, apply sealant between the dome and the bracket, wall veneer slits, and leading-out holes of the wall.
Wall Mount
1. Open the bracket cover, mount it onto the wall or pole (use pole adaptor).
2. Put on 3 screws onto the bottom of the camera, leave enough space to fit
in the screw holes on the bracket, not to screw tight.
3. Hold up the camera close under the bracket, insert the tail-cable of the
camera into the chest of the bracket.
4. Insert the 3 screws into the screw holes and turn the camera counter-
clock wise so that the camera can be held by the camera. Screw up the 3
screws but not too tight.
5. Put on the 4th screw and screw in tightly. Screw in the rest of the screws
tightly.
6. Finish the cable connection. Put all cable and connectors inside of the
bracket.
7. Put the cover back to the bracket and screw in securely.
Laser Illuminator
Adaptive IR Laser Illuminator
The EX1000 PTZ series camera uses adaptive IR laser illuminator to provide up to 1000 ft /1500 ft of long range
illumination. IR laser uses diffused illumination that provide the long distance visibility.
Precaution & Specs:
1. This product uses Class 3B laser light product.
2. Supports Manual / Auto IR laser control
3. Uses synchronous zoom with continuously adjustable illumination angle of 68 °~ 2 °.
4. Supports intelligent light-adjustment which automatically adjust the power of infrared laser light and avoids
reflective object and close range image overexposure.
5. Mount a laser dome camera at a height of six (6) meters (19.7 ft) from the ground. To avoid bodily injury from
the laser radiation, please make sure that no one is within the range of three (3) meters (9 ft) from the camera
when the laser is working.
6. When the IR laser is operating, do not look directly into the laser beam or obstruct the pathway of the beam.
7. Everyone who uses a laser should be aware of the risks and take necessary caution when handling, operating and
maintaining the product.

15
Starting the Camera
After you have mounted the camera properly, connect the camera to power.
Each time the camera is powered on, it will perform a self-test to check the Pan/Tilt/Zoom (PTZ function). After self-test, you
can operate the camera.
NOTE:
•The self-test process starts after the camera is powered up. Please wait patiently.
•When the operating temperature is lower than zero degrees Celsius, the camera will be automatically pre-heat (the pre-
heat process takes 30 minutes at most). The self-test starts only after the temperature rises above zero degrees Celsius.
Setting Camera over the LAN
To view and configure your camera via the local area network (LAN), you need to install the VMS (Video Management
System) to access IP camera.
1. Connect your camera and your PC as shown in the figure below to ensure the routing is available.
2. Use VMS or IPC-Search-Tool to search available camerasonthenetworkautomatically.
3. Modify the camera settings if necessary, including its IP address and subnet mask.
NOTE:
•The default IP address is “192.168.0.13”. The default username is “admin”, and the default password is “admin” or
“123456”.
•To access your camera from a different subnet, set the gateway for your camera after you log in.
Accessing Your Camera
For camera models with IP output, you can manage and control through the web interface from a PC.
System Requirements for YourPC
1. Operating System: Microsoft Windows 8/Windows 7/Windows XP (32-bit or 64-bit). Microsoft Windows 7 (32-bit) is
recommended.
2. CPU: 2.0 GHz or higher, dual-core. Intel i3 CPU or higher are recommended.
3. Memory: At least 1 GB. 2 GB (or higher) is recommended.
4. Graphic Card: At least 128 MB display memory. Mainstream discrete graphics with more than 1 GB display memory are
recommended. The hardware should supportDirectX9.0c. Make sure that the latest driver is installed on graphic card.
5. Sound Card: Essential. The intercom and voice broadcast require the latest driver on sound card.
6. Network Card: Gigabit Ethernet network cards (or higher) are recommended.
Accessing Your Camera
Before you begin, please check:
1. Make sure the self-test is completed.
2. Your camera is operating properly and connected to the network.
3. The PC client you are using is installed with Internet Explorer 8.0 or higher.
4. Open Internet Explorer on your PC.
5. In the address bar, input the IP address of your camera (Default IP is 192.168.0.13) and then press Enter to open
the login page.
6. Enter the username (default is “admin”) and password (default is “admin” or “123456”) and then click Login.

16
NOTE:
•Install the ActiveX on your first login. For detailed steps, see Installing the ActiveX. When the installation of the ActiveX
is completed, open IE to log in.
Installing the ActiveX
•The following message will show in IE browser on first login. Click Download to install Active X.
•Click Run. You may also click Save to download the file to your computer first.
•Close the browser and follow the steps to complete the installation.
NOTE:
•For your first login with Windows 7, if the system does not prompt you to install ActiveX, follow these steps to turn off UAC:
Click the Start button, and then click Control Panel. In the search box, type UAC, and then click Change User Account Control
Settings. Move the slider to the Never Notify position, and then click OK. After UAC is turned off, log in again.
•If the installation fails, open Internet Option in IE before login. Click the Security tab, click Trusted sites, and then click Sites
to add the website. If you use Windows 7, you need to save the setup.exe to your PC first, and then right-click the file, select Run
as administrator, and then install it according to instructions.

17
Part Two: Network Camera User Manual
Network Connection
Before accessing a network camera (also known as IP Camera or IPC) from a PC, you need to connect the network
camera to the PC directly with a network cable or via a switch or router.
Use a Shielded Twisted Pair (STP) cable to connect the network interfaces of the network camera and the PC.
Use Shielded Twisted Pair (STP) cables to connect the network interfaces of the camera and the switch or router.
Login
Preparation
After you have completed the installation in accordance with the quick guide, connect the camera to power to start it.
After the camera is started, you can access the camera from a PC client installed with a web browser or the video
management software. Internet Explorer (IE) is a recommended web browser. Please contact your dealer to get the
video management software. Please refer to the user manual of video management software for detailed information.
The following takes IE on a Microsoft Windows 7.0 operating system as an example.
Check before login
 The camera is operating correctly.
 The network connection between the PC and the camera is normal.
 The PC is installed with Internet Explorer 8.0 or higher.
 (Optional) The resolution is set to 1440 x 900.

18
Add the IP address as a trusted site
Follow the illustrations bellow:
NOTE:
NOTE:
•The IP address 192.168.0.13 in this example is the default IP address. Please replace it with the actual address of
your camera if it has been changed.
Modify user access control settings(Optional)
Before you access the camera, follow the steps to set User Account Control Settings to Never notify.
2
4
http://192.168.
0.13
Clear the check
box

19
Logging In to the Web Interface
The default static IP address of the camera is 192.168.0.13, and the default subnet mask is 255.255.255.0. DHCP is
turned on by default. If a DHCP server is used in the network, the IP address of your camera may be assigned
dynamically, and you need to use the correct IP address to log in. Use the video management software to view the
dynamic IP address of your camera.
The following takes IE as an example to describe the login procedure.
1. Browse to the login page by entering the correct IP address of your camera in the address bar.
2. If you log in for the first time, follow system prompts and install the ActiveX. You need to close your browser to
complete theinstallation.
3. Click Allow to proceed the login process.
NOTE:
•To manually load the ActiveX, type http://IP address/ActiveX/Setup.exe in the address bar and press
•Enter.
•The default password is used for your first login. To ensure account security, please change the password after your
first login. You are recommended to set a strong password (no less than eightcharacters).
•The camera protects itself from illegal access by limiting the number of failed login attempts. If login fails six times
consecutively, the camera locks automatically for tenminutes.
4. Enter the username and password, and then click Login. For the first login, use the default username
admin and password 123456 or admin.
 If you log in with Live View selected, live video will be displayed
when you are logged in. Otherwise, you need to start live video
manually in the live view window.
 If you log in with Save Password selected, you do not need to
enter the password each time when you log in. To ensure
security, you are not advised to select SavePassword.
 To clear the Username and Password text boxes and the Save
Password check box, clickReset.
NOTE:
•Important: Be sure to keep the new password written down and put in a safe place. If the password is forgotten,
camera will require hardware resetting. Additional charges may apply for reset services.
•Forgot Password? If you forget the password, email the device Product Bar Code and camera’s current time
mm/dd/yy to [e-mail] for a temporary password. You will be able to change the password
after login.

20
Introduction to the Web Interface
By default, the live view window is displayed when you are logged in to the Web interface. The following shows an
example.
Initial Configuration
After you log in to the device, please perform the following initial configuration.
1. Set the TCP/IP address for the device: Reconfigure the device IP and network parameters based on the actual
networking.
2. Log out and log in again to the Web using the new IP address.
3. Set the system time for actual situation.
4. (Optional) Setting the management server based on the actual networking.
5. Set OSD, set the information displayed on the screen as needed.
6. (Optional) Manage users. Change the default password and add common users as needed.
You can watch the live video after finishing the initial configuration. Please configure other parameters as needed.
1. Model Number
2. Menu
3. PTZ control area. This area is available for PTZ dome cameras and PTZ cameras.
4. Live view window
5. Live view toolbar
NOTE:
•The displayed live view interface, parameters displayed and value ranges may vary with models. Please see the
actual Web interface for details.
•The parameters that are grayed out cannot be modified. For the actual settings, see the Web interface.
•It is recommended that you change the password when you are logged in the first time. For details about
•How to change a password, see Security.
1
5
4
3
2