Bon Pergola DM45EAF/S User manual

BON PERGOLA

STEP1
1-1 1-2

cross countersunk head self-drilling
STEP2

cross countersunk head self-drilling
hole
motor
STEP3
24”
24”
24” 24”
7/9”
7/9”

STEP4

hole
STEP5
24”24”24”
24”24”24”
7/9”
3/5”

STEP6

STEP7

STEP8

STEP9

* For reference only.
DM45EAF/S
Features
Built-in Receiver
Precise Limit Setting
Jog & Tilt
Limit Fine Adjustment
Motor Mode Switching
Switch Direction
Stall Protection
Program Button
Reset to Factory Mode
Signal Repeater Function
Electronic Limit
Preferred Stop Position
Auto Limit Setting
Sensitive Stall Detection
-1-
SAFETY NOTE
1. This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved.
2. Children shall not play with the appliance.
3. Cleaning and user maintenance shall not be made by
children without supervision.
4. If the supply cord is damaged, it must be replaced by
the manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
5. WARNING: the drive shall be disconnected from its
power source during cleaning, maintenance and when
replacing parts.
6. The instructions shall state that the A-weighted emis
sion sound pressure level of the drive is equal to or
less than 70 dB(A), e.g. by writing LpA ≤ 70 dB(A).
7. The mass and the dimension of the driven part shall be
compatible with the rated torque and rated operating
time.
8. The type of driven part the drive is intended for.
9. WARNING: Important safety instructions. It is important
for the safety of persons to follow these instructions.
Save these instructions.
10. Do not allow children to play with fixed controls. Keep
remote controls away from children.
11. Frequently examine the installation for imbalance and
signs of wear or damage to cables and springs. Do not
use if repair or adjustment is necessary.
12. Watch the moving shutter and keep people away until
the shutter is completely closed.
13. WARNING: Important safety instructions. Follow all
instructions, since incorrect installation can lead to
severe injury.
14. Before installing the drive, remove any unnecessary
cords and disable any equipment not needed for
powered operation.
Attention
Never drop, knock, drill or submerge the motor. Keep the power cable in right position as following.
Important safety instructions to be read before installation.
Incorrect installation can lead to serious injury and will void manufacturer’s liability and warranty.
Fields of Application
The motor is suitable for motorization of zip screen.
Instruction A-01
Following data for reference
Specifications
Working Temperature: -10℃~ +65℃
Rated Voltage: 230V/50Hz
Radio Frequency: 433.92MHz
Thermal Protection time: > 4 minutes
Model Rated Torque
(N.m)
Rated Speed
(rpm)
Rated Current
(A)
DM45EAF/S-10/15 10 15 0.48
DM45EAF/S-10/26 10 26 0.69
DM45EAF/S-20/15 20 15 0.69
DM45EAF/S-20/26 20 26 0.9
DM45EAF/S-30/15 30 15 0.87
DM45EAF/S-40/15 40 15 0.99
DM45EAF/S-50/12 50 12 0.99

-2- -3-
Functions of P1 button
1. Cycle Operation：Press P1 button once and every press the motor will run upward → stop → downward → stop circulary.
2. Pairing or Pair Additional Emitter：Press P1 button for 2S, motor jog once, release button and long beep once, motor is
ready for pairing or pair additional emitter.
3. Radio Lock: Press and hold P1 button for 6S, motor jog once, release button and beep twice, the motor enters radio lock
status, the motor won't receive any signal; press P1 button once or the motor is powered off to disable Radio Lock.
4. Switch Direction: Press and hold P1 button for 10S, motor jog once, release button and beep 3 times, the running direction
of the motor has been changed.
5. Reset to Factory Mode: Press and hold P1 button for 14S, motor jog once, release button and beep 4 times, the motor has
been reset to factory mode.
Wiring
Three wires: 230V/50Hz
Motor Installation
Drive tube
Drive tube
Step 1 Cut drive tube to required length.
Step 3 Mount correct crown & drive adapter on
the motor. Make sure drive adapter fits firmly and
crown rotates freely.
Step 4 Align the notches on the crown and drive
adapter with the drive tube, slide and fit the motor
into drive tube. Mount idler and bracket on both
ends.
Step 2 Ensure tube edge is clean and burr-free.
②Drive Adapter
①Crown
③Circlip
Bracket
Bracket
Caution
1. Do not expose motor to humid, damp or extreme temperature conditions.
2. Do not drill into motor.
3. Do not cut the antenna and keep it clear from metal objects.
4. Do not allow children to play with this device.
5. If power cable or connector is damaged, do not use.
6. Ensure correct crown and drive adaptor are used.
7. Ensure power cable and aerial is clear and protected from moving parts.
8. Cable routed through walls shall be properly isolated.
9. Motor is to be mounted in horizontal position only.
10. Before installation, remove unnecessary cords and disable equipment not needed for powered
operation.
11. Installation and programming to be performed by a qualified professional, use or modification outside
the scope of this instruction may void warranty.
1
2
3
Neutral line = Blue
Live line = Brown
Earth line = Green Yellow
Motor
Important Safety Instructions To Be Read Prior To Operation.
Please read following points of attention carefully before setting.
Setting Notice
1. Pls take the wire connnector to protect the extra free wires.
2. Operation：
①The valid interval time of the buttons is within 6S, if there is no operation within 6S, the emitter will exit
the present setting.
②The motor will jog and beep as hint, pls operate after the jog and beep.
3. Set limit position：
①After the upper/lower limit setting,and the upper/lower limit positin can’t at the same position.
②After limit setting, with power off and memory function.
③Limit delete will clear all limit memory.
④It will exit limit setting when program there is no operation for 2 minutes.
4. If the emitter lost, please setting up again with new emitter.
5. One motor can store maximum 10 channels; after fully stored, if pair new channels, only the last one will be
covered circularly.
P1 button
P1
Back
P2
M
P2
Lithium Cell
3V
P2
DD1602H 15-channel LCD emitter
UP
Display
STOP
DOWN
Channel
selection“-”
(P1-)
Channel
selection“+”
(P1+)
P2
Button Instructions
→
P1
P1
1 Pairing
2 Switch Rotating Direction (Optional)
Essential Settings
Step 1 to 3 must be completed to ensure proper operation.
+
UP DOWN
Press UP and motor runs downwards, try below to switch direction.
*The motor needs to be in the reversing operation without limit.
Press and hold UP and DOWN buttons simultaneously for 2S, motor
jog once, the direction has been switched successfully.
Press P1 button for 2S (1 jog), release button and long beep once,
or repower, within 7S, press STOP for 2S ( 2 jogs and 3 beeps), the
motor has been paired successfully.
STOP
*If no limits, this operation will be pairing; if with limits, this operation will be pairing additional emitter.

-4- -5-
*The automatic setting of the limit function must be performed in mode 1; It's freely to set the upper limit or lower limit
firstly; If there is no limits, the motor will be jog running, or press UP or DOWN button 2S, then the motor will be
continuous running; After the limits have been set, the motor will be continuously running.
1 Manually set upper limit
Press UP for 2S, operate the motor to desired
upper position, press and hold UP and STOP
buttons simultaneously for 2S (2 jogs and 3 beeps),
upper limit is set.
Press UP for 2S,the motor will run upward and
stop after detecting obstacle, the stop position is
the upper limit; then the motor will run downward
automatically and stop after detecting the obstacle,
the curtain is pulled in reverse according to the
weight of the bottom beam, after the tension is
applied, the motor stops here and is the lower limit.
→
UP UP STOP
+
2 Manually set lower limit
Press DOWN for 2S,operate the motor to desired
lower position, press and hold DOWN and STOP
buttons simultaneously for 2S (2 jogs and 3 beeps),
lower limit is set.
STOP
→
DOWN DOWN
+
3 Setting Upper and Lower Limits
4 Automatically set upper limit, manually set lower limit3 Automatic limits setting
UP
Press UP for 2S,the motor will run upward and stop
after detecting the obstacle, the stop position is the
upper limit; then the motor will run downward
automatically to the desired lower position, press and
hold DOWN and STOP buttons simultaneously for 2S
(2 jogs and 3 beeps), the lower limits has been set
→
UP DOWN STOP
+
4 Add A Preferred Position
1 Set preferred position
P2
→ →
P2
STOP STOP
Check both upper and lower limits are set. Operate
the product to desired preferred position. Press P2
(1 jog and 1 beep), press STOP(1 jog and 1 beep),
STOP again (2 jogs and 3 beeps), the preferred
position is set.
2 Remove preferred position
P2
→ →
P2
STOP STOP
Press P2 (1 jog and 1 beep), press STOP(1 jog and
1 beep), STOP again (1 jog and long beep once), the
preferred position is deleted.
*Press STOP for 2S,the motor moves to preferred position automatically; In the automatic return function state, at the
return limit position of the lower limit position, want to press STOP to run to preferred position,the motor will first run
to the lower limit position, this action is to release ofthe curtain, and then run to preferred position.
*This must be done in mode 1; after entering the limit fine adjusting status 2MIN, if no new limits are set , then the
motor will exit the limit fine adjusting status and remain the old limits.
5 Adjust Limits
1 Adjusting the upper limit position
2 Adjusting the lower limit position
→ → →
STOPUP DOWNUP
or
+
STOPUP
+
The new upper
limit position
Press and hold UP and STOP buttons simultaneously for 5S (1 jog and long beep once), operate the
product to desired new upper limit position, press and hold UP and STOP buttons simultaneously for 2S
(2 jogs and 3 beeps), the new upper limit is programmed successfully.
Press and hold DOWN and STOP buttons simultaneously for 5S (1 jog and long beep once), operate the
product to desired new lower limit position, press and hold DOWN and STOP buttons simultaneously for 2S
(2 jogs and 3 beeps), the new lower limit is programmed successfully.
DOWN STOP
+
DOWN STOP
+
DOWNUP
or
→ → →
The new lower
limit position
6 Activate / Deactivate Jog / Tilt Mode
*It must be done after setting the upper limit and the lower limit.
DOWN
→
STOPUP
+Press and hold UP and DOWN buttons simultaneously for 5S (1 jog),
press STOP (1 jog and long beep once), Jog / tilt mode is activated.
If motor jogs twice and beeps 3 times, Jog / tilt mode is deactivate.
• Repeat same procedure will unpair additional emitter.
*(a) as existing emitter, (b) as new emitter to pair/unpair.
7 Pair / Unpair Additional Emitter
P2 P2
→ →
P2
P2(a) P2(a) P2(b)
Press P2 (1 jog and 1 beep) and P2 (1 jog and 1 beep) on existing
emitter, press P2 on new emitter to add (2 jogs and 3 beeps), new
emitter is paired to the motor.
Method one
Press P2 (1 jog and 1 beep) and P2 (1 jog and 1 beep) on existing
emitter, press STOP on new emitter for 2S to add (2 jogs and 3 beeps),
new emitter is paired to the motor.
Method two
P2 P2
→ →
P2(a) P2(a) STOP(b)
Press P1 button for 2S (1 jog), release button and long beep once,
press STOP on new emitter for 2S to add (2 jogs and 3 beeps), new
emitter is paired to the motor.
Method three
STOP(b)
→
P1
P1
→ →
8 Remove All Emitters
P2
P2
P2
P2
STOP
→ →
P2
P2
P2
P2
DOWN
9 Deleting All Limits
*After deleting all emitters, keep the original limit information.
*This operation is deleted along with the preferred position.
Press P2 (1 jog and 1 beep), STOP (1 jog and 1 beep), and P2 (2 jogs
and 3 beeps), all emitters are deleted.
Press P2 (1 jog and 1 beep), DOWN (1 jog and 1 beep), and P2 (2 jogs
and 3 beeps), all limits are removed.
→ →
10 Motor Mode Switching
P2
P2
*Factory default mode 1 motor;
Mode 1 motor is applied to the zib screen motor with no self-locking structure, can automatically set the limit and
automatically adjust the limit 50 times, without the automatic return function of the lower limit;
Mode 2 motor is equipped with zib screen motor with self-locking structure, and automatic return function for lower
limit (automatic locking and unlocking).
Press P2 (1 jog and 1 beep), UP(1 jog and 1 beep), UP again (1 jog
and long beep once), switch to mode 1 motor. If motor jogs twice and
beeps 3 times, switch to mode 2 motor.
UP UP
STOP
11 Motor Lower Limit Return Function
DOWN
→ →
P2
P2
Press P2 (1 jog and 1 beep), STOP(1 jog and 1 beep), and DOWN
(1 jog and long beep once), motor turns on automatic debugging and
return function. If motor jogs twice and beeps 3 times, motor turns on
manual debugging and return function.
*It can only be done when the motor is under mode 2; The factory default motor turns on automatic debugging and
return function.

-7--6-
If there is a limit, the motor is in the upward direction, it will be repelled and protected. After rebounding for a
certain distance, it will continue to run upwards. If it encounters resistance at the same position twice, it will
stop after the second resistance rebound. If there is no limit, the motor will run upward and stop after
detecting obstacle.
If there is a limit, the motor is down, it will be repelled and protected. After rebounding for a certain distance,
it will continue to run downward. If it encounters resistance at the same position twice, it will stop after the
second encounter with the rebound. Light resistance does not work; the protection function does not work
during the rebound.
15 50 Times Running Self-calibration Function
It can only be done when the motor is under mode 1; After the upper and lower limit is automatically set,
the motor runs to the lower limit and then runs to the upper limit to run once. When it runs to 50 times, it
automatically corrects the lower limit (resets the lower limit automatically), and stops if fine adjustment or
changes the original limit. Automatically correct the count.
13 Enable / Disable Sensitive Stall Detection Function
DOWN
→ →
P2
P2 DOWN
Press P2 (1 jog and 1 beep ), DOWN(1 jog and 1 beep ), DOWN again
(1 jog and long beep once), sensitive stall detection function is disabled.
If motor jogs twice and beeps 3 times, sensitive stall detection function
is enabled.
*The factory default mode is ON.
14 Resisting / Sensitive Stall Detection Fallback Function
12 Signal Repeater Function
Press P2 button once(1 jog and 1 beep), press and hold P2 button 5S
(2 jogs and 3 beeps ), the signal repeater function has been activated.
If motor(1 jog and long beep once), the signal repeater function has been
deactivated.
P2
P2
*The factory default mode is OFF. Signal repeater function off is the factory default mode and only the motor has the
limits, the signal repeater function can be activated. The motor doesn't repeat the signal from the paired address.
Troubleshooting
Issues Possible causes Solution
The motor has no response
Power Failure Or Incorrect Connection
emitter battery is low capacity Replace battery
Radio interference / shielding
Out of radio control range Try control within closer range
The emitter cann't control
single motor
Multiple motors are paired to the
same channel.
Always reserve an individual correctly (refer to motor functions)
Try to use multi-channel emitters to control multi-motor
projects, ensure each channel to control one single motor
The motor doesn't run or starts
too slowly or make loud noise
The motor stops during the going
up or going down.
Connections are incorrect. Check connections
Incorrect installation or overload
The motor has reached the lower limit
Running time exceeds 4 min
Adjust the new lower limit
Consult the sales for more information
Check installation or overload
Check antenna on motor is intact and exposed. Check for
possible source of radio interference.
Double check power and cable connections, follow wiring
instructions.
Quick Index
Settings Steps
Pairing
Switch Rotating Direction
Upper and Lower Limits Setting
Adjust Limits
P1 (hold down 2s) → Stop (hold down 2s)
Up + Down (hold down 2s)
Manually set upper limit Up (hold down 2s) → Up + Stop (hold down 2s)
Manually set lower limit Down (hold down 2s) → Down + Stop (hold down 2s)
Automatic limits setting Up (hold down 2s)
Automatically set upper limit,
manually set lower limit Up (hold down 2s) → Down + Stop (hold down 2s)
Adjusting the upper limit Up + Stop (hold down 5s) → Up or Down →
Up + Stop (hold down 2s)
Adjusting the lower limit Down + Stop (hold down 5s) → Up or Down →
Down + Stop (hold down 2s)
5
Add / Remove Preferred Position
4
3
2
1
Activate / Deactivate Jog / Tilt Mode
Pair / Unpair Additional Emitter
Remove All Emitters
Deleting All Limits
Up + Down (hold down 5s) → Stop
P2(a) → P2 (a) → P2(b)
P2 → Stop → P2
P2 → Down → P2
6
7
8
9
Motor Mode Switching
Motor Lower Limit Return Function
P2 → Up → Up
P2 → Stop → Down
10
Signal Repeater Function P2 (hold down 5s)12
11
Enable / Disable Sensitive Stall
Detection Function P2 → Down → Down13
P2(a) → P2 (a) → Stop (b) (hold down 2s)
P1 (hold down 2s) → Stop (b) (hold down 2s)
P2 → Stop → Stop