Bon Pergola Villa Pergola User manual

1
User Instructions
Villa Pergola for motorized operation
Size:10’x10’(300x300cm)
10’x13’(300x400cm)
13’x13’(400x400cm)

2

3
Content
Tools and man force ............................................................................3
Parts List..............................................................................................4-6
Product Description..............................................................................7
Safety Instruction..................................................................................7-8
Mounting................................................................................................9-18
Dismounting...........................................................................................19
Storage...................................................................................................19
Disposal..................................................................................................20
Attention:
Read this instruction manual carefully and completely before mounting and
usage. Keep this manual for future reference.

4
Dear Customer,
Congratulations and welcome to our Villa Pergola family. To enjoy your Villa Pergola for its lifetime and for you and
other’s safety, please follow the assembly instructions.
Before you start the assembly process and using the Pergola, we suggest you are best to get familiar with this
product. Make sure all parts listed up in below packing lists are delivered and intact. If you find that there are parts
missing or damaged please do not install the pergola but contact us immediately. Do not start the assembly process
if parts are missing or defective.
Tools and man force
Recommended: 2 or 3 people
Additional tools :
1. Ladder 2. M10/13 open wrench supplied 3.Rubber mallet
4. Tape measure 5. 5mm hexagon wrench supplied 6.Pencil
7. Spirit level 8. Electric drill

5
Parts List
Please check all parts against the parts list before commencing construction of pergola.
SIZE:10’x10’ or 300X300CM PARTS LIST:

6
SIZE:10’x13’ or 300X400CM and 13’x13’ or 400X400CM PARTS LIST:
Hardware and other parts:
①M8x20 countersunk screw
②50 to 40 connector
③Base plate
④Upright cover
⑤M10 screw cap
⑥M8x20 Hexagon bolt
⑦Plastic Spacer
⑧Locking nut
⑨Motor with motor bracket
⑩M8X100 expansion bolt
⑪Gutter connector

7
Aluminum profile parts list:
ⒶBeam with slots
ⒷBeam with motor direction & slots
ⒸBeam
Post + post connector
Post + post connector
Post + post connector
ⒺGutter
ⒻGutter
ⒼCommon louver
ⒽCentre louver
ⒾDriving louver
ⒿControl rod
Product Description
Make the most of your outdoor living area with your pergola. Relax and enjoy the outdoors while being protected
from sun. The coated aluminum frame pergola is perfect for shading your garden, deck, courtyard and swimming
pool.
Important Safety Instructions
Warning: For the safety of you and other persons it is important to follow below instructions and obey
warnings.
Symbol explanation
This warning triangle calls attention to hazards that that can lead to death or to severe
injuries or which are important for the functioning of the Pergola.
This sign identifies important notes.
Safety instructions
To install this pergola technical knowledge is necessary. Do not mount this
pergola yourself but contact a professional workman for help if
you are unsure if the pergola can be mounted on the place you chose for
installation.
you do not understand the instruction manual or parts of it.
you do not have necessary tools available.
you do not have necessary technical knowledge
D1
D3
D2

8
A minimum of three healthy adults are required to move and install the pergolaas
the product is big and heavy. Do not try to install the pergola alone. If the pergola falls,
it could cause serious injuries and damages! Contact an authorized assembler for help.
Do not install the pergola when you find damage parts are that parts are missing.
Contact your dealer.
Keep children and pets out of the working area during assembly and
adjustments.
This product and its fixing parts are only suitable for installation on a plain
cement wall or stable brickwork. If the wall/brickwork shows cracks you have to
consult a professional.
Nobody is allowed to change the products’ design and structure without the
permission of manufacture or authorized deputy.
Please make sure that your hands are clean at the time of the assembly; otherwise you
may soil frame.
Nobody is allowed to climb onto the Pergola. Hanging anything on the Pergola is
forbidden.
Sheeting was used to protect the paint. This must be removed afterwards.
This structure is a non-permanent structure and the warranty does not cover damage
incurred under extreme weather conditions including heavy rain, high winds or if
exposed to high heat from heaters or BBQs.
Safety precautions should always be followed when assembling and using this product
to reduce the risk of personal injury and damage to equipment. Please read all
instructions before assembly and use. Never leave children unattended around/under
this pergola. Do not attempt to assemble or use the pergola in moderate or heavy wind
conditions. Always keep the pergola louver open and secure it during heavy winds or
extreme weather conditions to avoid damage to the pergola or personal injury.

9
Mounting and usage
Step 1
Attach base plate ③x4 to the bottom of posts ( x1, x2 ,and x1),use bolts
①x8 to attach with hex key or electric drill
posts should be installed diagonally as below
D1
D2
D3
D2

10
Step 2
Attach beamⒶX1 Ⓑx1 and Ⓒbeam x1,use bolts ⑥to fasten

11
Step 3
Attach beamⒸx1, use bolts ⑥x12 to fasten

12
Step 4
Attach upright cover ④x4,use bolts ⑥x8 to fasten

13
Step 5
1. Slide the ⑨motor into Ⓕgutter before hooking onto the beam in the direction
as shown below.
2. Attach all four gutters (Ⓔx2 andⒻx2 )by hooking inside theⒶ, Ⓑ,Ⓒbeams

14
Step 6
Fasten motor ⑨x1 with its screws as shown below.

15
Step 7
1. Fasten ⑪x4 gutter connector
2. If motor wire is running downward through the post, use ②to connect with ⑪as
shown below to not allow water drain through this post.

16
Step 8
Connect the female and male plugs for the LED lighting
(DC24V to DC24V) and motor (DC24V to DC24V) and
plug the power cable into local socket.
***Note: You can test your motor at this stage. Plug in and use its remote.

17
Step 9
Located holes in center of beams(ⒶandⒷ)
1. Place Center Louver on the slot where it is align with the hole visible.
For 10’x10’ (300x300cm):
Place Center Louver Ⓗinto 12th slot, lining up with the open holes.
For 10’x13’ (300x400cm) and 13’x13’ (400x400cm):
Place Center Louver Ⓗinto 16th slot, lining up with the holes for 10’x13’
(300x400cm) and 13’x13’ (400x400cm) size.
2. Using M10 nut ⑤X2, secure the Center Louver in place.
3. Place Driving Louver Ⓘin line with 7th slot on the beam ⒶandⒷ.
4. Place all Common Louvers ⒼX21 for 10’x10’ (300x300cm) and ⒼX30 for both
10’x13’ (300x400cm) and 13’x13’ (400x400cm) size into the remaining slots in the
beams

18
Step 10
Fix Ⓙx 2 (flat L-shaped aluminum profile).
One for each other of the slats is required.
*Use bolt⑥x46, plastic spacer⑦x46 and nut⑧x46 to tighten for 300x300 cm and
400x400cm size*.
*Use bolt⑥x64, plastic spacer⑦x64 and nut⑧x64 to tighten for 300x400 cm and
400x400cm size.
Secure the louvers at each end.
***NOTE: Do not over tighten. Over tightening will
prevent louvers from moving.

19
Step 11
Mark holes for expansion bolt ⑩x4 on each post.
Note the drill size should be 12 mm.
Insert the bolts. Use a hammer drill if necessary. Place the posts
over the bolts. Tighten the nuts.
Once installed, make sure any remaining plastic is removed and silicone is used
along all corners and gutters to be waterproof.
Tight nuts
WARNING: Make Sure louvers are open during periods of mild to strong winds to
avoid damage overtime.

20
Motor set up