Allen + Roth L-GZ1150PST-B User manual

2
PACKAGE CONTENTS
W1
W2
F1
Z1
H T G
U3
U4
V3
V1
V4
W3
W4
B
Z4
A4
C
A3
Z3
J K2
F2
V2
A1
E A2 Z2
D
N
L7
L6
L5
X1
Y4
Y3
M
L2
L1
R1
O
P
R2
Q
L3 L4
X2 Y1 K1 Y2
S I
U1 U2

3
PACKAGE CONTENTS
PART DESCRIPTIONQUANTITY
A1
A2
A3
A4
B
C
D
E
F1
F2
J
K1
K2
L1
L2
L3
L4
L5
L6
L7
M
N
O
Q
P
R1
R2
S
T
U1
U2
U3
U4
G
H
I
PART
Left Beam (Short Side)
Right Beam (Short Side)
Left Beam (Long Side)
Right Beam (Long Side)
Beam Connector 1
Beam Connector 2
Big Roof Top Beam
Big Roof Middle Beam
DESCRIPTIONQUANTITY
2
2
2
2
4
4
4
4
2
4
1
2
4
2
2
4
4
4
2
4
4
4
4
4
4
1
Big Top Frames 1
Big Top Frames 2
Small Roof Cover
Small Roof Panel 1
Small Roof Panel 2
Big Roof Panel 1
Big Roof Panel 2
Big Roof Panel 3
Big Roof Panel 4
Big Roof Panel 5
Big Roof Panel 6
Big Roof Panel 7
Small Roof Sheeting
Big Roof Sheeting
4
4
Post
Base
Base Cover
4
4
4
1
2
2
2
2
Left Support
Right Support
Inside Corner Cover
Hook
Big Roof Beam 1
Big Roof Beam 2
Big Roof Beam 3
Big Roof Beam 4
Small Roof Top Beam
Small Roof Connector
Corner Support

4
PACKAGE CONTENTS
V1
V2
V3
V4
W1
W2
W3
W4
X1
X2
Y4
Z1
Z2
Z3
Z4
Y1
Y2
Y3
PART
Big Roof Beam 5
Big Roof Beam 6
Big Roof Beam 7
Big Roof Beam 8
Big Roof Beam 9
Big Roof Beam 10
Big Roof Beam 11
Big Roof Beam 12
DESCRIPTIONQUANTITY
2
2
2
2
2
2
2
2
2
2
2
2
8
2
2
2
2
2
Small Roof Bottom Panel 1
Small Roof Bottom Panel 2
Big Roof Sheeting 4
Long Left Netting Tube
Long Right Netting Tube
Short Left Netting Tube
Short Right Netting Tube
Small Roof Sheeting 1
Small Roof Sheeting 2
Big Roof Sheeting 3

8
ASSEMBLY INSTRUCTIONS
•
1. Insert the posts (O) into the base covers
(Q), then attach the bases (P) to the
posts (O) using screws (AA) and flat
washers (EE). Tighten with wrench (II)
1
AA
Hardware Used
M6 x 15 mm Bolt x 16
x 16
EE M6 Flat Washer
x 1
Fig.1
Fig.7
H
Fig.11-1
Fig.11-2
Fig.5
B
Fig.6
Fig.2
A1
A2 A3 A4
Fig.3
Fig.4
Fig.8-1
Fig.8-2
Fig.9
Fig.10
C
E
G
F2
F1
Fig.12
O
P
Q
A4
A3
F1 F2
H
B
P
Q
O
G
C
E
A2
A1
1
M6 Wrench
II
AA
P
Q
O
EE

9
ASSEMBLY INSTRUCTIONS
2. 1
2
1
2
Insert left beams (short side) (A1) to the 11
right beams (short side) (A2), secure with
bolts (AA) and flat washers (EE), then
tighten with wrench (II). Repeat these
instructions
to insert left beam (long side )
(A3) into the right beams (long side) (A4).
3. Attach the connectors 2 (C) to the
assembled connected beams of step 2
using bolts (AA) and flat washers (EE),
tighten with wrench (II).
3
11
4. Attach one end of assembled right beams
(A4) to the posts (O) using bolts (CC) and
flat washers (EE). Tighten with wrench
(II). Use these same instructions to
attach the other assembled beams (A1,
A2, A3) to the posts (O).
4
11
4
CC EE
O
O
EE
A4
A1
CC
Hardware Used
x 4
x 4
EE M6 Flat Washer
AA M6 x 15 mm Bolt
x 1
Hardware Used
x 8
x 8
x 1
Hardware Used
x 16
x 16
EE M6 Flat Washer
CC M6 x 45 mm Bolt
x 1
A3
3
EE
EE
AA
AA
C
A1
A2
M6 Wrench
II
EE M6 Flat Washer
AA M6 x 15 mm Bolt
M6 Wrench
II
M6 Wrench
II
2

10
ASSEMBLY INSTRUCTIONS
12-1
7
7. Connect the big top frames 1 (F1) with the
big top frames 2 (F2) using bolts (AA) and
flat washers (EE). Tighten with wrench
(II).
12-1
6
6. Attach the connectors 1 (B) to the upper
side of posts (O) using bolts (AA) and flat
washers (EE). Tighten with wrench (II).
12-1
5
5. Attach the left supports (R1) to the left
beams (long side) (A1) and the posts (O)
using bolts (AA) and flat washers (EE),
tighten with wrench (II). Use these same
instructions to attach the right supports
(R2).
11
6
A3
A2 O
B
EE
AA
11
5
O
A1
R1
A4
EE
AA
7
F2
F1
EE AA
Hardware Used
x 12
x 12
x 1
Hardware Used
x 8
x 8
x 1
Hardware Used
x 32
x 32
EE M6 Flat Washer
AA M6 x 15 mm Bolt
x 1
M6 Wrench
II
EE M6 Flat Washer
AA M6 x 15 mm Bolt
M6 Wrench
II
EE M6 Flat Washer
AA M6 x 15 mm Bolt
M6 Wrench
II

11
9. Attach the upper end of big roof middle
beams (E) to the middle of assembled big
top frames (F1 & F2) using bolts (AA) and
flat washers (EE). Tighten with wrench
(II).
9
11
8-1
8-1. Attach the upper end of big roof top
beams (D) to the assembled big top
frames (F1 & F2) using bolts (AA) and
flat washers (EE). Tighten with wrench
(II). (Note: A ladder and one
assistant is required to complete this
step.)
11
8-2
8-2. Attach the other end of big roof top
beams (D) to the connectors 1 (B) using
screws (DD), nuts (GG) and flat washers
(EE). Tighten with wrench (II).
ASSEMBLY INSTRUCTIONS
8-2
O
D
B
EE DD
8-1
D
F1
F2
EE
AA
Hardware Used
x 8
x 8
x 1
Hardware Used
x 8
x 8
x 1
Hardware Used
x 16
x 8
x 8
EE M6 Flat Washer
GG M6 Nut D HH
x 2
EE
AAC
E
9
F1
E
EE M6 Flat Washer
AA M6 x 15 mm Bolt
M6 Wrench
II
M6 Wrench
II
EE M6 Flat Washer
AA M6 x 15 mm Bolt
M6 Wrench
II
EE
GG
DD M6 x55 mm Bolt

12
ASSEMBLY INSTRUCTIONS
10. Attach the other end of big roof middle
beams (E) to the connectors 2 (C) using
bolts (DD), nuts (GG) and flat washers
(EE). Tighten with wrench (II).
11-1
11-1. Attach the upper end of small roof top
beam (G) to the small roof connector (H)
using screws (DD), nuts (GG) and flat
washers (EE). Tighten with wrench (II).
11-2. Attach the other end of small roof top
beams (G) to the assembled big top
frames (F1& F2) using bolts (AA) and
flat washers (EE). Tighten with
wrench (II).
1311-2
E EE
EE
A2
DD
GG
A1
G
EE
AA
F2
F1
H
G
EE
DD
EE
GG
Hardware Used
x 8
x 8
EE M6 Flat Washer
AA M6 x 15 mm Bolt
x 1
Hardware Used
x 16
x 8
x 8
x 2
Hardware Used
x 8
x 4
x 4
x 2
EE M6 Flat Washer
GG M6 Nut D
DD M6 x 55 mm BoltHH
II M6 Wrench
EE M6 Flat Washer
GG M6 Nut D
DD M6 x 55 mm Bolt5H
II M6 Wrench
M6 Wrench
II
C
10

13
ASSEMBLY INSTRUCTIONS
12. Screw the hook (T) to the small roof
connector (H). 1512
T
H

14
ASSEMBLY INSTRUCTIONS
13. Attach the small roof bottom panels 1
(X1) to the end of small roof top beams
(G) using bolts (AA) and flat washers
(EE). Tighten with wrench (II). Use the
same instructions to attach the small roof
bottom panels 2 (X2).
13
EE
AA
X1
G
Fig.13
Fig.15
Fig.14
Fig.16
Fig.17
Fig.20
Fig.19
Fig.21
Fig.18
Fig.22
Fig.23
Fig.24
U3 U4
U2
U1
V1
V2 V3 V4
Z4
Z3
Z2
Z1
W1
W2
W3 W4
E
D
Y2
Y1
J
M
K2
K1
M
E
D
J
Z3
W4
Z1
Z2 Z4 V4
V3
V2
V2
U1
Y1 K1 K2
Y2
U2 U3 U4
W3
W1
W2
x 8
x 8
EE M6 Flat Washer
AA M6 x 15 mm Bolt
x 1
M6 Wrench
II
Hardware Used

15
ASSEMBLY INSTRUCTIONS
16. Attach the small roof sheeting (M) to the
small roof top beams (G) using bolts (BB)
and flat washers (EE). Tighten with
wrench (II). Top with plastic caps (FF).
18
11
16
EE
FF
K2
K1
M
Hardware Used
x 8
x 1
II M6 Wrench
EE M6 Flat Washer BB
BB I M6 x 40 mm Bolt
BB
FF Plastic Cap x 8
14.Attach the small roof panels 1 & 2 (K1&
K2) to the small roof top beams (G) using
screws (AA) and flat washers (EE).
Tighten with wrench (II).
Hardware Used
x 8
x 8
x 1
AA M6 x 15 mm Bolt
EE M6 Flat Washer
II M6 Wrench
14
EE
K2
K1
AA
15.Attach the small roof panels 2 (K2) and the
small roof sheeting 2 (Y2) to the small top
bottom panels 1 (X1) using screws (AA)
and flat washers (EE). Tighten with wrench
(II). Use the same instructions to attach the
small roof panels 1 (K1) and the small roof
sheeting 1 (Y1) to the small top bottom
panels 2 (X2). Top with plastic caps (FF).
AA
Hardware Used
M6 x 15 mm Bolt x 8
x 8
EE M6 Flat Washer
x 1
II M6 Wrench
15
EE
AA
FF
K2
X1
x 8
FF Plastic Cap x 8
Y2

A1
EE
AA D
I
16
ASSEMBLY INSTRUCTIONS
11
17
19.
Attach the inside corner covers (S) to left
& right beams (A2 & A3) using bolts (AA)
and flat washers (EE). Tighten with
wrench (II). Repeat these instructions for
the left & right beams (A1 & A4).
18. Attach the corner supports (I) to the left &
right beams (A1 & A4) using bolts (AA)
and flat washers (EE). Tighten with
wrench (II). Repeat these instructions for
the left & right beams (A2 & A3).
EE
AA
EE
D
O
SI
A3
A2
Hardware Used
x 8
x 8
x 1
Hardware Used
Hardware Used
x 2
EE M6 Flat Washer
x 1
18
17.
Attach the small roof cover (J) to the small
roof connector (H) using bolt (CC) and flat
washer (EE). Tighten with wrench (II). Top
with plastic caps (FF).
19
II M6 Wrench
I M6 x 45 mm Bolt
CC
AA M6 x 15 mm Bolt
EE M6 Flat Washer
M6 Wrench
II
x 8
x 8
x 1
AA M6 x 15 mm Bolt
EE M6 Flat Washer
M6 Wrench
II
FF
CC
FF Plastic Cap x 2
x 2
J
A4

AA
D
U4
EE
17
ASSEMBLY INSTRUCTIONS
20. Attach the big roof beams 4 (U4) to the 20
big roof top beams (D) using bolts
(AA) and flat washers (EE). Tighten with
wrench (II).
Hardware Used
21. Attach the other end of big roof beams 4
(U4) to the big roof middle beams (E)
using bolts (AA) and flat washers (EE).
Tighten with wrench (II). Use the same
instructions to attach the rest of big roof
beams (U1 & U2 & U3 & V1 & V2 & V3
& V4).
21
U4
E
Hardware Used
22
EE
D
Z2
22. Attach the one end of right netting tubes
(long side) (Z2) to the big roof top beams
(D) using bolts (AA) and flat washers
(EE), and the other end to the big roof
middle beams (E) using the same bolts
(AA) and flat washers (EE). Tighten with
wrench (II). Use the same instructions to
attach the rest of the netting tubes (Z1,
Z3 & Z4).
Hardware Used
x 4
x 4
x 1
AA M6 x 15 mm Bolt
EE M6 Flat Washer
M6 Wrench
II
x 28
x 28
x 1
AA M6 x 15 mm Bolt
EE M6 Flat Washer
M6 Wrench
II
x 16
x 16
x 1
AA M6 x 15 mm Bolt
EE M6 Flat Washer
M6 Wrench
II
EE AA
AA

18
ASSEMBLY INSTRUCTIONS
EE
W4
D
23
24. Attach the other end of big roof beams
24
12 (W4) to the big roof middle beams (E)
using bolts (AA) and flat washers
(EE). Tighten with wrench (II). Use the
same instructions to attach the remaining
beams (W1 & W2 & W3).
Hardware Used EE
W4
AA
E
23.
Attach one end of the big roof beams 12
(W4) to the big roof top beams (D) using
bolts (AA) and flat washers (EE). Tighten
with wrench (II).
Hardware Used
x 4
x 4
x 1
AA M6 x 15 mm Bolt
EE M6 Flat Washer
M6 Wrench
II
x 12
x 12
x 1
AA M6 x 15 mm Bolt
EE M6 Flat Washer
M6 Wrench
II
AA

L6,Attach the big roof panels (L1, L2, L3, L5, 26
L6, L7) to the big roof top beams (D)
using bolts (AA), flat washers (EE) and
plates (FF). Tighten with wrench (II).
19
ASSEMBLY INSTRUCTIONS
26.
L2
L
L7
L6
L5
Hardware Used
25
25. Press big roof panels 2 (L2) to big roof
panels 1 (L1). Repeat this step for all
other roof panels (L3, L4, L5, L6) in order
from left to right as shown.
L2
L1
L3
L4 L5 L6
Fig.25
L2
L7
Fig.26
Fig.27
Fig.28
Fig.29
J
K2
K1
M
M
J
K1 K2
L1
L2
L6
L3
L4 L5 L6 L7
L1
x 24
x 24
x 1
AA M6 x 15 mm Bolt
EE M6 Flat Washer
M6 Wrench
II
26
L1
L3
AA
EE JJ
x 12
JJ Plate
L1
L2L3
L5
L7

ASSEMBLY INSTRUCTIONS
29. Attach the big roof sheeting 3 (Y3) to the
big roof beams 12 (W4) using bolts (AA)
and flat washers (EE). Tighten with
wrench (II). Top with plastic caps (FF).
EE
AA
L5 L6
Y3
L7
Hardware Used
20
28. Attach the big roof sheeting 4 (Y4) to the
big roof beams 11 & 12 (W3 & W4) using
bolts (AA) and flat washers (EE). Tighten
with wrench (II). Top with plastic caps (FF).
27. Attach the big roof sheeting (N) to the
big roof top beams (D) using bolts
(BB) and flat washers (EE). Tighten
with wrench (II). Top with plastic caps
(FF).
27
L4
II
BB
II
BB
N
Hardware Used
Hardware Used
x 8
EE M6 Flat Washer
x 1
II M6 Wrench
BB M6 x 40 mm Bolt
x 4
x 4
x 1
AA M6 x 15 mm Bolt
EE M6 Flat Washer
M6 Wrench
II
x 24
x 24
x 1
AA M6 x 15 mm Bolt
EE M6 Flat Washer
M6 Wrench
II
29
FF
FF
FF
Y4
28
AA
EE
FF Plastic Cap
FF Plastic Cap
FF Plastic Cap
x 8
x 8
x 4
x 24
FF
W3
W4