Bon Pergola Villa Pergola 13x19 User manual

1
User Instructions
Villa Pergola motorized operation
Size: 13’x19’ Double Bay
( 400 x 600cm )

2
Content
Tools and man force ...........................................................................1-2
Parts List.............................................................................................2-5
Product Description..............................................................................6
Safety Instruction..................................................................................6-7
Mounting................................................................................................8-17
Dismounting...........................................................................................18
Storage...................................................................................................19
Disposal..................................................................................................19
Attention:
Read this instruction manual carefully and completely before mounting and usage.
Keep this manual for future reference.
Dear Customer,
Congratulations and welcome to our Villa Pergola family. To enjo y your Villa Pergola for its lifetime and for you and
other’s safety, please follow the assembly instructions.
Before you start the assembly process and using the Pergola, we suggest you are best to get familiar with this
product. Make sure all parts listed up in below packing lists are delivered and intact. If you find that there are parts
missing or damaged please do not install the pergola but contact us immediately. Do not start the assembly process
if parts are missing or defective.

3
Tools and man force
Recommended: 2 or 3 people
Additional tools :
1.Ladder 2. M10/13 open wrench supplied 3.Rubber mallet
4.Tape measure 5. 5mm hexagon wrench supplied 6.Pencil
7.Spirit level 8.Electric drill

4
Parts List
Please check all parts against the parts list before commencing construction of pergola.
SIZE
：
13’x19’ or 400X600CM (double bay) PARTS LIST

5
Aluminum profile parts list:
(A1) Beam
(A2 ) Beam
(B1) Beam
(B2) Beam
(C1) Beam
(C2) Beam
(C3) Middle Beam
(D1) Post + post connector
(D2) Post + post connector
(D3) Middle Post + post connector
(E1) Gutter
(E2) Gutter
(F1) Gutter
(F2) Gutter
(G) Common Louver
(H) Steering Louver
(I) Strenthen Louver
(J) Steering profile
Hardware and other parts:
② M8x20 countersunk screw
②50 to 40 connector
③Base plate
④Upright cover
⑤M10 screw cap
⑥M8x20 Hexagon bolt
⑦Plastic washer DAP25
⑦Locking nut
⑨Motor with motor bracket
⑩Gutter connector
⑪wall bracket
○
12 Slider
○
13 L-Bracket
○
14 Cover plate
○
15 M8X100 Internal anchor
○
16 M8X100 Anchor
○
17 Base plate caps

6
Product Description
Make the most of your outdoor living area with your pergola. Relax and enjoy the outdoors while being protected
from sun. The coated aluminum frame pergola is perfect for shading your garden, deck, courtyard and swimming
pool.
Important Safety Instructions
Warning: For the safety of you and other persons it is important to follow below instructions and obey
warnings.
Symbol explanation
This warning triangle calls attention to hazards that that can lead to death or to severe
injuries or which are important for the functioning of the Pergola.
This sign identifies important notes.
Safety instructions
To install this pergola technical knowledge is necessary. Do not mount this pergola
yourself but contact a professional workman for help if
¨ you are unsure if the pergola can be mounted on the place you chose for
installation.
¨ you do not understand the instruction manual or parts of it.
¨ you do not have necessary tools available.
¨ you do not have necessary technical knowledge
A minimum of three healthy adults are required to move and install the pergolaas
the product is big and heavy. Do not try to install the pergola alone. If the pergola falls,
it could cause serious injuries and damages! Contact an authorized assembler for help.
Do not install the pergola when you find damage parts are that parts are missing.
Contact your dealer.

7
Keep children and pets out of the working area during assembly and adjustments.
This product and its fixing parts are only suitable for installation on a plain
cement wall or stable brickwork. If the wall/brickwork shows cracks you have to
consult a professional.
Nobody is allowed to change the products’ design and structure without the
permission of manufacture or authorized deputy.
Please make sure that your hands are clean at the time of the assembly; otherwise you
may soil frame.
Nobody is allowed to climb onto the Pergola. Hanging anything on the Pergola is
forbidden.
Sheeting was used to protect the paint. This must be removed afterwards.
This structure is a non-permanent structure and the warranty does not cover damage
incurred under extreme weather conditions including heavy rain, high winds or if
exposed to high heat from heaters or BBQs.
Safety precautions should always be followed when assembling and using this product
to reduce the risk of personal injury and damage to equipment. Please read all
instructions before assembly and use. Never leave children unattended around/under
this pergola. Do not attempt to assemble or use the pergola in moderate or heavy wind
conditions. Always keep the pergola louver open and secure it during heavy winds or
extreme weather conditions to avoid damage to the pergola or personal injury.

8
Mounting and usage
Step 1
Attach base plate
③
x3 to the bottom of posts (D1 /D2/D3),use bolts ○ 1 x 12 to attach
with hex key or electric drill.
D1 ,D2, D3 posts should be installed diagonally as below.
Please make sure all posts on the same horizontal plane.

9
Step 2
According the height of ○ C2 to measure the height of○ 15 ,use anchor to fasten

10
Step3
Use bolts ○ 12 x6 to fasten beam ○ B1 & beam ○ B2 .

11
Step 4
Insert the ○ A1 / ○ C1 into ○ D1 ,then connect ○ B1 with ○ 13 ,fasten the screws.

12
Step 5
Connect ○ A2 /○ B2 with ○ 13 ,fasten the screws,and insert the middle beam ○ C3
Lock the screws

13
Step 6
Connect the ○ B1 and ○ B2 , insert ○ C1 into ○ D3 , fasten the screws.

14
Step 7
Cover the post with ○ 4x2,fasten the screws.

15
Step 8
Cover the beam on both sides with ○ 14 ,fasten the screws

16
Step 9
Placed all gutter ○ E1 ,○ E2 ,○ F1 ,○ F2 in proper position as picture

17
Step 10
Fasten motor
⑨
x2 with its screws as shown below.

18
Step
1
1. Fasten ○ 10 x2 gutter connector
2. If motor wire is running downward through the post, use② to connect with○ 10
as shown below to not allow water drain through this post.

19
Step 12
Connect the female and male plugs for the LED lighting
(DC24V to DC24V) and motor (DC24V to DC24V) and
plug the power cable into local socket.
***Note: You can test your motor at this stage. Plug in and use its remote.

20
Step 13
Place center louver
Ⓗ
into 16th slot, lining up with the holes
Using M10 nut
⑤
X2, secure the louver in place
Place Steering louvers
Ⓘ
X2 in line with 7th slot on the beam
○
A1
and
○
A2
.
Fit all common louvers
Ⓖ
X58 into the remaining slots in the beams