Royalcraft ZURICH ZURGAZ3X3-GREY User manual

-2 -
Warning
4.. The screws/bolts to anchor to a wooden deck and concrete patio are not included.
5. DO NOT REMOVE THE PROTECTIVE FILM ON THE POLYCARBONATE ROOF PANELS
BEFORE INSTALLATION. MAKE SURE TO PUT THE UV PROTECTED SIDE FACING UP TO THE
SUN. IT IS A VERY IMPORTANT PROCEDURE; IF NOT FOLLOWED AS DESCRIBED, YOUR ROOF
WILL NOT BE COVERED BY THE GUARANTEE
Attention
1. Damages due to vandalism, abuse and incorrect use of the product are not covered by the warranty
2. Damages due to extreme weather conditions such as thunderstorm, hail and high winds are not
covered by warranty.
3. Canopy and/or Curtains will fade in the sunshine, the chemicals that make up the colours within the
polyester fabric are broken down by ultraviolet light that is present in the sunshine, this is a natural
process and is not covered by the guarantee or warranty. We do try to counteract this process by putting
a UV resistant additive to the fabric however this only protects the fabric for a certain amount of time.
Excluded
1. It is the consumer's responsibility to comply with any relevant local planning requirements.
2. Two-Four persons are required for assembly. The tools required are a screwdriver or wrench, stepladder
and other relevant safety items such as gloves. We recommend the use of protective equipment.
3. This gazebo will take at least 1-2 hours to set up. You must allow enough time to complete the assembly.
Do not leave it unattended if not fully assembled, even if bolted to the ground.
A. Make sure that all components are in the box. Read instructions carefully before starting the assembly.
B. Follow all instructions carefully to assure the strength of the gazebo.
C. In order to avoid damage to the gazebo and its components, use appropriate tools. Do not use the
structure as a support; a stepladder is recommended.
D. Check all screws on a regular basis to maintain the solidity of the structure.
E. Keep the instructions and parts list for further use.
Maintenance
1. In the event that your gazebo needs replacement parts, repairs or you require assistance with regards
to assembly; please contact our customer sales team by email [email protected]
2. For cleaning: Use a mild domestic soap or soft detergent and wash with warm water using a sponge or
microfibre fabric. Rinse with clean water.
3. To preserve the fabric (curtains) we recommend the use of a UV protector spray like Fabsil. This will
help block the harmful UV rays from damaging the fabric and will also keep the fabric protected from
discoloration.
Your gazebo has been created for all four seasons and will resist snow accumulations of up to 5kg/m².
You will need to remove any excess of snow on the roof at all times.
The mosquito netting and the curtains must be removed for winter storage.
This Gazebo with curtains should only be used as a sunshade.
Make sure the product is fixed firmly to the ground or have a suitable weighted base to hold them in
place. If not secured or weighted down they will move position in high winds.
Please be aware that this product is not a permanent structure and we recommend removing the
curtains between October and March. These are the months when the weather will cause damage to
the fabric.
Note! This gazebo is meant to be used for decorative and sunshade purposes only and is
not meant to withstand all elements of the weather. Please remove all FABRIC during
adverse weather conditions.

-3 -

- 4 -
STEP ONE:
1A. CONNECT PART 2 x PART A IN THE MIDDLE USING H2 BOLTS.
1B. CONNECT PART C UNDERNEATH YOUR TWO PART A’S USING H5 BOLTS
STEP TWO:
CONNECT PART J TO PART A USING PART L AND H6 BOLTS
(AS PER DIAGRAM BELOW)

- 5 -
STEP THREE:
CONNECT ALL PARTS A TO PARTS A1 USING H BOLTS
STEP FOUR & FIVE:
4. CONNECT PARTS B1 TO B2 WITH PART K USING H1 BOLTS (AS PER DIAGRAM)
5A. CONNECT PART G TO ALL PARTS B2
5B. CONNECT PART I TO ALL PARTS D
5C. CONNECT ALL B1 (B2) AND D TO PARTS F & E (AS PER DIAGRAM)

- 6 -
STEP SIX:
CONNECT YOUR BUILT ROOF SECTION TO THE TOP OF YOUR BUILT FRAME USING H1
BOLTS
STEP SEVEN (1&2):
7-1A. SLIDE PANEL ONE INTO YOUR FRAME FOLLOWED BY PART C1, PANEL 3 AND PART
D2 (AS PER DIAGRAM)
7-1B. SLIDE PANEL TWO INTO YOUR FRAME FOLLOWED BY PART C1, PANEL 3 AND PART
D1 (AS PER DIAGRAM) THEN SECURE ALL PARTS WITH H4 BOLT
7-2. CONNECT PART N TO EACH CORNER OF YOUR FRAME AND PART M TO EACH CENTRE
OF YOUR FRAME USING H3 BOLTS

-7 -
STEP EIGHT & NINE:
8. CONNECT PART A2 WITH PART B USING H1 BOLTS
9. LIFT YOUR BUILT TOP FRAME (USING MIN 4 PEOPLE) ONTO YOUR A2 (B) AND SECURE
THE JOIN WITH H4 BOLTS

-8 -
STEP TEN:
HOOK PARTS W ONTO PART J USING PART O (AS PER BELOW DIAGRAM) AND THEN
SECURE YOUR FRAME TO THE GROUND USING PART Y (ONLY APPLICABLE FOR GRASS)