Sunjoy L-GZ212PCO-B1 User manual

Instruction Manual
Item #: L-GZ212PCO-B1

1. Keep all children and pets away from assembly area. Children and pets should be
supervised when they are in the area of gazebo construction.
IMPORTANT:
2. The area for assembly should not be less than 6 feet from any obstruction such as fence,
garage, house, overhanging branches, laundry line or electrical wires.
3. This unit is heavy. Do not assemble this item alone. Six people are recommended for safe
assembly.
4. Some parts may contain sharp edges. Wear protective gloves if necessary during assembly.
5. When assembling and using this product, basic safety precautions should always be
followed to reduce the risk of personal injury and damage to equipment. Please read all
instructions before assembly and use.
6. For outdoor use only. Install on level ground. Stakes are provided to secure the gazebo in
grass ground. If you wish to secure the gazebo to a wood deck or concrete surface, you will
need to purchase fasteners appropriate for these surfaces. These are readily available at your
local hardware store or home center.
7. Check all bolts for tightness before and during usage.
8. While this gazebo is manufactured to withstand gale force winds utilizing only the supplied
ground stakes, in areas subject to frequent severe weather, securing the gazebo to a deck,
concrete patio or footings should be considered.
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with
package contents list. If any part is missing or damaged, do not attempt to assemble the
product.

Finial A 1
Small top connector B1 1
Hook B2 1
Small top arch beam C 4
Upper screen corner
connector 1 D1 2
Upper screen corner
connector 2 D2 2
Upper screen long connector E 2
Upper screen short
connector F 2
Arch beam G1 4
Long side middle beam G2 2
Short side middle beam G3 2
Arch beam connector 1 H1 2
Arch beam connector 2 H2 2
Middle beam connector I 4
Short decorative slot 1 J1 2
Short decorative slot 2 J2 2
Long decorative slot 1 K1 2
Long decorative slot 2 K2 2
Short mosquito netting pipe L1 4
Long mosquito netting pipe L2 4
Post 1 M1 4
Post 2 M2 4
Parts List

Post connector 1 N1 4
Post connector 2 N2 4
Long side arch support beam O1 6
Short side arch support
beam 1 O2 2
Short side arch support
beam 2 O3 2
Small canopy P 1
Large canopy Q 1
Mosquito netting R 1
Parts List
AA M6X15 Bolt 36 PCS
BB M6 Flat washer 52 PCS
CC M6X15 Screw 16 PCS
W M6 Wrench 1 PCS
Hardware Pack 1

Fig.1:
Insert short
decorative slot 1 (J1) into
(J2), then secure middle
beam connector (I) to (J1)
& (J2) by bolt (AA) and
washer (BB). Install long
decorative slot (K1) and
(K2) in the same way.
Fig.2:
Insert short
decorative slot 2 (J2) into
long decorative slot 1 (K1).
Secure A
rch beam
connector 1 (H1) and Post
connector 1 (N1) to (J2) &
(K1) by bolt (AA) and
washer (BB). Install H2 in
the same way.
Fig.3:
Attach post
connector 2 (N2) to
long decorative slot
(K1) & (K2) bolt (AA)
and washer (BB).
Fig.4:
Attach mosquito
netting pipe (L1) and (L2)
to decorative slot (J1) &
(J2) & (K1) & (K2) by
screw (CC) and washer
(BB).
Fig.5: Insert upper
screen connector (E)
and (F) into upper
screen corner connector
(D1) & (D2).
Fig.6:
Insert middle
beam (G2) & (G3) into
upper screen connector
(E) & (F).
Fig.7:
Insert middle
beam (G2) and (G3) into
middle beam connector
(I).
Fig.8: Insert arch beam
(G1) into
upper screen
corner connector (D1) &
(D2).
F

Fig.9: Insert arch
beam (G1) into arch
beam connector (H1)
or (H2).
Fig.10: Insert small top
arch beam (C) into small
top connector (B1), and
attach hook (B2) to (B1).
Fig.12: Put the large canopy
(Q) onto the top, then insert
small top arch beam (C) into
(D1) & (D2). Spread (Q) and
fix it to the frame by the hook
on the canopy.
Fig.11: Put the small
canopy (P) onto the
small top, then attach
finial (A) to small top
connector (B1).
AA M6X15 Bolt 46 PCS
BB M6 Flat washer 46 PCS
Hardware Pack 2
Fig.13:
Lift the
assembled frame, insert
post 1 (M1) into post
connector (N1), fully
tighten by bolt (AA) and
washer (BB).
Fig.14: Insert post (M2)
into post connector
(N2), fully tighten by bolt
(AA) and washer (BB).
Fig.16: Attach long
side arch support
beam (O1) to post
(M1) or (M2) by bolt
(AA) and washer
(BB).
Fig.15: Attach long side
arch support beam (O1)
to long decorative slot
(K1) & (K2) by bolt (AA)
and washer (BB).

Fig.17&17-1: Attach short side arch
support beam (O2/O3) to post (M1) &
decorative slot (J1) & (J2) by bolt (AA)
and washer (BB).
EE Plastic ring 60PCS
FF Φ6X180MM Stake 24PCS
Hardware Pack 3
Fig.18: Attach the mosquito netting (R)
to mosquito netting pipe (L2) & (L1). Fig.19: Fix the assembled gazebo to the ground by stake (FF).

Limited Warranty:
This limited warranty is extended to the original purchaser and applies to defects in materials
and workmanship of your item provided the item is maintained with care and used only for
personal, residential purposes. The item is warranted to be free from defects in material or
workmanship for a period of one (1) year. We don't reimburse for transportation or
delivery costs, or compensate the individual or any outside party for assembling or
disassembling the product.
Exclusions:
Items used for commercial, contract, or other non-residential purposes, or items damaged due
to acts of nature, vandalism, misuse, or improper assembly are not covered. Corrosion or
rusting of hardware is not covered. Proof of purchase (dated register receipt) is required for
warranty claims. Warranty is to the original purchaser and is non-transferable. Any
replacement of warranted items will be in the original style and color, or a similar style and
color if the original is unavailable or has been discontinued. As some states do not allow
exclusions or limitations on an implied warranty, the above exclusions and limitations may not
apply. This warranty gives you specific rights, and you may also have other rights, which vary
from state to state.
Maintenance:
Our iron/steel components for garden accessories and patio items are coated with rust
inhibiting paint that protects it from rusting. However, due to the nature of iron, surface
oxidation (rusting) will occur once these protective coatings are scratched.
This is a natural
process and is not a defect! To minimize this condition, we recommend care when assembling
& handling the product to prevent scratching the paint. Should any scratching or damage occur,
we recommend immediate touch-up with rust inhibiting paint. Surface rust can also be easily
removed with a very light application of common cooking oil. If surface oxidation (rusting)
occurs and if no measure is taken to prevent this, the oxidation may start dripping on to deck or
patio and cause damaging stains, which may be difficult to remove. This can be prevented if
measure is taken to keep the product from oxidizing.
Important: Please do not return this product to the store. For technical assistance on
assembly or replacement parts. Please call Sunjoy Industries at 1-866-578-6569 from 8:00 am
EST to 8:00 pm PST or fax the replacement part form which is in the box to 1-740-283-3549 or
Email [e-mail] for assistance.
Made in China
2016-2