BOND MANUFACTURING Gatewood 50436 User manual

DANGER
WARNING
WARNING
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open ame.
3. If odor continues, keep away from
the appliance and immediately call
your gas supplier or re department.
Do not store or use gasoline or other
ammable vapors and liquids in the
vicinity of this or any other appliance.
An LP-cylinder not connected for use
shall not be stored in the vicinity of
this or any other appliance.
For outdoor use only.
Owner’s Manual
Gatewood Gas Fire Table
Item# 50436
Lowe’s# 733486
SERIES
Improper installation, adjustment, alteration, service or maintenance can cause injury or
property damage. Read the owner’s manual thoroughly before installing or servicing this
equipment. If the information in this manual is not followed exactly, a re or explosion may
result causing property damage, personal injury or loss of life.
Save these instructions for future use. If
you are assembling this unit for someone
else, give this manual to him or her and
read and save for the future.

Bond Manufacturing Company | Page 2
WARNING
Before you assemble or operate this unit, please carefully read this entire manual. Failure to do so
may result in a re, explosion, injury or death.
SAFETY INFORMATION
• The installation of this unit must adhere to local codes or either the National Fuel Gas Code, ANSI
Z223. 1/NFPA54, OR CAN/CGA-B149.1, National Gas and Propane Installation Code.
• THIS UNIT IS INTENDED FOR OUTDOOR USE ONLY! This product shall be used outdoors, in a
ventilated space and shall not be used in any enclosed area.
• This unit is to be used with propane gas only! (sold separately)
• Do not attach a remote gas supply to this unit.
• Only use propane gas for this unit.
• This unit is not intended for natural gas.
• Converting this unit to natural gas is dangerous and not recommended. The conversion of this unit
will void the manufacturer warranty.
• Do not use any solid fuel or charcoal for this unit.
• When igniting this unit, stay away from the burner as the ame will light up and may cause injury.
• LP GAS WARNING: Do not use any more than 1/4in depth lava rocks/pumice stones/LavaGlass™
above the burner holes. Doing so will suffocate the ame.
• If the propane gas tank is leaking gas, you may hear, see, or smell a hiss. Do the following:
1. Disconnect the propane gas tank. 2. Do not attempt to x the problem yourself. 3. Contact your gas
supplier or re department for help.
• Applying too much propane may result in gas pooling and will not burn. Allow fresh air into the unit
so that the remaining gas may escape.
• Do not use a ame to check for gas leaks.
• The max. inlet supply pressure: max. Gas supply 11 in w.c. (2.74kPa)
• Use LP propane tanks with the following dimensions: diameter 12 in, height 18 in.
• You must use a propane tank that has a collar to protect the gas valve.
• DO NOT ll tank over 80 percent full.
• The tank system must be set up for vapor withdrawal.
• Discontinue use if any part of the propane tank is damaged. Rust and dents may be hazardous and
should be inspected by a gas supplier.
• Do not burn anything other than the provided materials for this re table.
• Keep away from the unit for the rst 20 minutes after igniting your unit for the rst time, as lava
rocks/pumice stones/LavaGlass™ could pop out and cause injury. Should any rocks pop out, discard
them.
• Always ensure that lava rocks/pumice stones/LavaGlass™are completely dry before use. Failure to
do so will cause them to crack or pop.
• Do not operate unit until all parts are fully assembled.
• Do not paint or color any part of this heating unit.
• Unit may be hot while in use, do not attempt to move it while in use.
• Never leave this heating unit unattended while in use.
• This unit is not intended for cooking.
• Keep any ammable items away and do not use any other replace cover for this unit.
• Keep a safe distance to avoid burning skin or clothing.
• Do not sit or rest hands or feet on this heating unit.
• Never place hands or ngers on upper portion of this unit while in use.
• Keep all electrical cords and fuel supply hose away from heated surfaces.

1-866-771-2663 | Page 3
• Combustible material should not be within 72 inches of the top of the unit, or within 48 inches
around the entire unit.
• Keep the appliance area clear and free from combustible material, gasoline and other ammable
vapors and liquids.
• If the ame goes out while burning, turn the gas valve off. Wait 5 minutes before repeating the initial
lighting procedure. Once you have a ame started, hold down the control knob for 1 minute.
• Do not add water into the unit.
• Do not operate unit if any part has been under water. Call a service technician to replace any
damaged parts should this occur.
• Do not disconnect any part while unit is in use.
• Do not store a spare propane tank on or near this unit.
• If the heating unit is indoors, detach the propane tank and leave outdoors.
• Do not operate on a boat or vehicle. This unit must be used on a at surface and outdoors ONLY.
• Always remove protective cover before operating (if applicable).
• Do not set the protective cover over the unit until it is turned off and completely cooled down.
• Check for leaks after not using the unit for long periods of time.
• Children should never operate this unit. Children must be supervised while near this unit.
• Keep gas tank at least 5 feet away from unit when lit. (if external tank)
• The maximum gas supply pressure is 250psi.
• All installation and repair should be done by a qualied professional. This unit should be
inspected annually and cleaned regularly.
• Inspect all elements of this heating unit before each use. If there is damage, the burner must be
replaced.
• Keep the hose out from any pathways to eliminate any accidental damage. (if external tank)
• Be aware of the hazards of high temperatures and stay away from the unit to avoid any burns or
injury.
• The gas supply tank should be constructed and marked with the specications for the LP gas tanks
of the U.S. Department of Transportation or the National Standard of Canada CAN/CSA-B339, LP gas
tanks, spheres and tubes for Transportation of Dangerous Goods; and Commission.
• The LP gas tank must have a listed overlling prevention device and a QCCI or Type I, (CGA810) LP
gas tank connection.
• This heating appliance should not be used on plastic or articial wood desks.
• Children and adults should be alerted to the hazards of high surface temperatures and should
stay away to avoid burns or clothing ignition.
• Young children should be carefully supervised when they are in the area of the appliance.
• Clothing or other ammable materials should not be hung from the appliance or placed on or
near the appliance.
• Any guard or other protective device removed for servicing the appliance shall be replaced
prior to operating the appliance.
• Installation and repair should be done by a qualied service person. The appliance should be
inspected before use and at least annually by a qualied service person. More frequent cleaning
may be required as necessary. It is imperative that the control compartment, burners and
circulating airways of the appliance are kept clean.
IF APPLICABLE:
• Allow heating item to cool completely before placing on lid.
• DO NOT use heating item while lid is installed. Always remove the lid while heating item is in use.

Bond Manufacturing Company | Page 4
SAFETY INFORMATION
Only use the regulator and hose assembly provided with this unit. Replacement parts must be supplied
directly by Bond Manufacturing Co.
Inspect the burner before use of this unit. If the burner shows any kind of damage, do not operate
the appliance. For assistance with repair or replacement of the burner or any other parts, calls Bond
Manufacturing at 1.866.771.2663.
NOTE: You must follow all steps to properly assemble this heating item. Make sure the gas
valve is turned “OFF” before assembling. Do NOT attempt to assemble without proper tools.
Combustible materials should not be within 72
inches of the top of the unit, or within 48 inches
around the entire unit.
Min. Clearance
48 in. (121.9 cm)
Min. Clearance
48 in. (121.9 cm)
Min. Clearance
48 in. (121.9 cm)
Min. Clearance
48 in. (121.9 cm)

1-866-771-2663 | Page 5
AA GGBB HHCC IIDD EE FF
Item Description Qty
AA M6 x 20 Bolt 8
BB M6 Washer 8
CC M6 x 30 Bolt 4
DD M8 x 16 Screw 4
EE M8 Washer 4
FF Propane Tank Strap 2
GG Touch Up Paint 1
HH Allen Wrench 1
II Wrench 1
HARDWARE
Before beginning assembly of this product be sure all parts are present. Compare parts with
package contents list and hardware contents list. If any part appears to be missing or damaged do
not begin assembly of this product and call customer service immediately.
Estimated assembly time: 30 minutes

Bond Manufacturing Company | Page 6
Item Description Qty
A Lid 1
B Firebowl 1
C Back Panel 1
D Table Top 1
E Left Side Panel 1
F Right Side Panel 1
G Bottom Plate 1
H Door Panel 1
I Burner (preassembled) 1
J Guard (preassembled) 1
K Control Knob (preassembled) 1
L Igniter (preassembled) 1
M Battery (AA) 1
N LavaGlass™ 2 bags
O Protective Cover 1
CONTENTS
I
A
C
D
E
F
G
H
N
K
L
B
J
M
O

1-866-771-2663 | Page 7
3. Attach the two panel constructions made in
the previous steps by placing a M6 x 20 bolt
(AA) through a M6 washer (BB), put the bolt and
washer through the aligned bolt slots and loosely
tighten with allen wrench (HH). (You will use four
bolts and four washers for this step.) Be sure
not to over tighten - you may need to adjust the
panels later on to ensure proper alignment.
ASSEMBLY INSTRUCTIONS
1. Align the back panel (C) to the left side panel
(E). Then attach by placing a M6 x 20 bolt (AA)
through a M6 washer (BB), put the bolt and
washer through the aligned bolt slots and loosely
tighten with allen wrench (HH). (You will use two
bolts and two washers for this step.) Be sure
not to over tighten - you may need to adjust the
panels later on to ensure proper alignment.
2. Align the door panel (H) to the right side panel
(F). Then attach by placing a M6 x 20 bolt (AA)
through a M6 washer (BB), put the bolt and
washer through the aligned bolt slots and loosely
tighten with allen wrench (HH). (You will use two
bolts and two washers for this step.) Be sure
not to over tighten - you may need to adjust the
panels later on to ensure proper alignment.
C
E
H
F

Bond Manufacturing Company | Page 8
ASSEMBLY INSTRUCTIONS
4. Attach two propane tank straps (FF) to the
bottom plate (G) in two cross corners as shown.
5. Rotate the door knob to unlock; open the door
on the door panel (H). Place the bottom plate (G)
into the front of the panel assembly as shown.
Secure the bottom plate (G) to the panels by using
four M6 x 30 bolts (CC). Tighten with wrench (II).
6. Remove the preassembled screws and washers
from the corners of the burner assembly (B). Place
the burner assembly (B) into the top of the table
top (D). Align the holes in the burner assembly
corners (B) with the holes in the top of the table
top (D) and replace the four screws and washers
removed at the beginning of this step. Be sure to
tighten completely.
G
G
FF
FF
D
B

1-866-771-2663 | Page 9
7. Attach the table top (D) to the panel
construction by aligning the holes at the bottom
of the table top (D) to the holes in the top of the
panel construction and securing with four M8 x 16
bolts (DD) and four M8 washers (EE); tighten with
wrench (II). Be sure to position the control panel to
be over the door panel (H).
Once attached, secure all bolts on the re table by
adjusting and tightening to ensure the structure is
sturdy.
9. Remove the rubber cap on the electronic igniter
(L) by unscrewing and slide battery (M) into the
battery slot. Make sure the positive side of the
battery faces outwards. Screw the electronic
ignitor cap (L) over the battery tightly.
8. Pour LavaGlass™ (N) into the rebowl (B).
L
N
J
M
D
To ensure proper function, the guard (J) on this
burner (I) should be free of LavaGlass™ at all
times.
CAUTION

Bond Manufacturing Company | Page 10
ASSEMBLY INSTRUCTIONS
10. Place a 20 lb. propane gas tank (not included)
into the round stand on bottom plate (G). Insert
one propane tank strap (F) through the handle
holes on the collar of the 20 lb. propane gas tank.
Connect with the other propane tank strap (F) by
attaching the buckles together. Tighten to secure.
CYLINDER VALVE
PRESSURE
RELIEF VALVE
BLEED-OFF
VALVE
BLACK COUPLING NUT
REGULATOR
turn clockwise to connect
turn clockwise
to reseal
11. Turn the cylinder valve on the tank
clockwise to close the propane tank.
Attach the preassembled regulator
from the table top (D) to the cylinder valve
by turning the regulator coupling nut
clockwise. Make sure it is fastened
securely and tighten connections by hand
only.
F
G

1-866-771-2663 | Page 11
To Light
To Extinguish
Before performing a leak test, be sure that no sparks can occur and you are in a spacious outdoor
area. Connect the propane gas tank to the regulator and turn the valve on the unit to the “off”
position. Brush a soap and water mixture on all connections. Turn the gas supply on; if bubbles
occur on any connection there may be a leak. If you smell gas or a leak is discovered turn the
gas valve off, disconnect propane gas tank and do not use the appliance until the leak is
repaired.
Do not use the heating unit without inspecting the gas hose. If there are signs of wear or abrasion
you must replace the hose (if applicable). Pumice stones/lava rocks/LavaGlass™could pop up and
strike somebody’s face during the process of lighting this unit; stand away from the unit for the rst
20 minutes after igniting. Flame height should be a yellow/blue color between 2 - 10 inches in height.
Wait 5 minutes after extinguishing ame prior to placing a lid (if applicable) or protective cover on
heating item.
1. Make sure the control knob (K) is in the “off” position.
2. Open the door on the door panel (H) and slowly open the valve on the propane gas tank by
turning the knob counterclockwise.
3. Push in the control knob (K) and turn counterclockwise to the “LOW” position. Keep holding
down the control knob (K) to allow gas to ow for 15 seconds prior to lighting.
4. While holding down the control knob (K) press down the igniter (L) to spark a ame and light
the re table. While pressing the igniter (L) you should hear a clicking sound. If needed keep the
control knob (K) and igniter (L) pressed down until the re table lights.
5. If ignition doesn’t occur within a few seconds release the control knob (K) and rotate to the “OFF”
position. Wait for 5 minutes for gas to clear and then repeat the above lighting instructions.
6. Once the re product is lit, the ame intensity may be controlled by turning the control knob (K)
between the “LOW” and “HIGH” positions.
7. Close the door on the door panel (H) on the body.
1. Turn control knob (K) to the “HIGH” position; let the knob pop up and continue turning the control
knob (K) to the “OFF” position.
2. Close the cylinder valve on the propane gas tank if you don’t intend to use it for a long time.
OPERATION

Bond Manufacturing Company | Page 12
MAINTENANCE
•Before performing any maintenance always disconnect propane gas tank.
•Keep the heating item free and clear from combustible materials.
•Visually inspect burner for obstructions and keep tank enclosure free and clear from debris.
•Use a soft brush to get rid of the mild stains, loose dirt and soil after the burner and pumice stones/
lava rocks/LavaGlass™ are completely cooled down. Wipe down with a soft cloth.
•Harsh weather conditions may cause stubborn stains, discoloration and possibly rust pitting.
•Permanent damage may occur if powder or solvent comes in contact with painted or plastic
components on this heating unit.
•Keep the heating unit stored away from direct sunlight.
•If storing this unit inside, disconnect the propane gas tank from the gas valve.
•Not using manufacturer approved or supplied parts/accessories may result in a defective condition
and void the warranty of this heating unit.
•Always place lid (if applicable) or protective cover on heating item when not in use.

1-866-771-2663 | Page 13
TROUBLESHOOTING
Problem Cause Solution
Igniter pin and burner are wet Dry off with a soft cloth
Igniter battery is incorrectly inserted Check which direction the battery is
inserted
Igniter pin is broken Contact Bond Manufacturing for a
replacement part
Electrode wire is loose or disconnected Reconnect wire to the igniter box located
inside the table behind the igniter box
Electrode wire is shorting between valve
and igniter pin
Contact Bond Manufacturing for a
replacement part
No gas flow Check that the gas tank isn’t empty
Regulator isn’t connected securely to the
tank
Tighten regulator connection to the gas
tank
Gas flow is obstructed Check all hoses for kinks and bends
Burner ports are clogged Turn all gas flow connections off. Insert
an opened paperclip (or similar item) into
each of the burner ports to clear them
out.
Flame is obstructed at burner ports Check that all burner ports are free of
any small lava rocks/pumice stones/
LavaGlass™ pieces
Regulator hose is kinked Straighten hose of all bends or kinks
No gas flow Check that the gas tank isn’t empty
Excess flow safety valve has been
activated
Turn the control knob to the ‘off’ position.
Close the tank valve and disconnect
propane gas tank. Turn the control
knob to ‘high’; wait 1 minute. Turn the
control knob back to the ‘off’ position.
Reconnect propane gas tank. Light the
fire unit as indicated in the ‘To Light’
section of this manual.
High or gusting winds Increase flame to ‘high’
No gas flow Check that the gas tank isn’t empty
Excess flow safety valve has been
activated
See ‘sudden drop in gas flow’ above
Heating unit won’t light
Burner won’t light
while using a match
Heating unit emits a lot
of black smoke
Sudden drop in gas
flow
Flame blows out easily

Bond Manufacturing Company | Page 14
WARRANTY
If you have any questions or concerns, please contact Bond Manufacturing Company at the below
resources:
CONTACT
Toll Free Phone [phone]-BOND (2663) | Monday - Friday, 8am - 4:30pm PST
Email customer[email protected]
Online www.bondmfg.com
The manufacturer warranty will be voided by, and manufacturer disclaims any responsibility for, the
following actions:
•Modication of the unit and/or components including the gas valve assembly.
•Use of any component part not manufactured or approved by Bond Manufacturing.
•Use and installation other than what is listed in this manual.
Please contact the manufacturer for replacement parts.