Bontrager Flare R User manual

Welcome.
BT16_MANUAL_FlareR_USEN_FINALv5.indd 1 3/4/16 4:46 PM

Parts
BT16_MANUAL_FlareR_USEN_FINALv5.indd 2 3/4/16 4:46 PM

Flare R
Quick Connect Bracket
Micro USB Cable
Parts
Bikeurope BV / Trek Benelux
Ceintuurbaan 2-20C
3847 LG Harderwijk
The Netherlands
Tel.: [phone] (BLX)
US Address: 801 West Madison Street, Waterloo, WI USA
US Phone: [phone]
BT16_MANUAL_FlareR_USEN_FINALv5.indd 3 3/4/16 4:46 PM

Charging and Charge Status
Although the Flare R is fully charged at the factory, it is
recommended to charge it before first use. Complete
charging takes approximately 2 hours from empty.
Flashing red: Actively charging.
As the battery progresses from zero charge (red) to full
charge (green), the flashes will get progressively longer
in duration. Green: Charging has completed
Charging LED progression
Charging
While charging via the USB port, the light will
remain off but the status LED will flash to show
the charging status.
Green
Red
IMPORTANT: Use a quality CE or UL approved USB
charger rated for 500 mA or greater.
Status LED
BT16_MANUAL_FlareR_USEN_FINALv5.indd 4 3/4/16 4:46 PM

Operation
Powering On
Press and release the power button one time to turn on
the light. The power button LED will show battery status.
Changing the mode
Each quick-press of the power button will change to the
next mode.
Locking the mode
Select the desired mode, then press and hold the power
button 8 seconds. The light will turn off and the main
LED will flash once.
Unlocking the mode
Press and hold the power button 8 seconds. The light
will turn off and the main LED will flash once.
Powering off
Press and hold
the power button
until the light
turns off.
IMPORTANT
Ensure USB cover is latched before riding in the rain or
in wet conditions. If USB cover is not closed, damage to
the light may occur.
Charging and Charge Status
Although the Flare R is fully charged at the factory, it is
recommended to charge it before first use. Complete
charging takes approximately 2 hours from empty.
Flashing red: Actively charging.
As the battery progresses from zero charge (red) to full
charge (green), the flashes will get progressively longer
in duration. Green: Charging has completed
Charging LED progression
Charging
While charging via the USB port, the light will
remain off but the status LED will flash to show
the charging status.
IMPORTANT: Use a quality CE or UL approved USB
charger rated for 500 mA or greater.
Main LED
Power Button
USB
Cover
BT16_MANUAL_FlareR_USEN_FINALv5.indd 5 3/4/16 4:46 PM

Mode Descriptions
Day Flash 65*
65-lumen random bursts for 5.75 hours
Day Flash 65 offers daytime visibility up to 2Km with all
super bright random pulses.
All-Day Flash 35*
35-lumen random bursts for 10 hours
All-Day Flash 35 offers daytime visibility up to 1Km with all
super bright random pulses and the side lights turned off
for an exceptionally long run time.
Night Flash 65*
Always on with the side lights turned off, 65-lumen short
duration bursts for 23 hours
Night Flash 65 is constantly on with short bright pulses
for optimized visibility in the night. It is designed to get
attention without dazzling approaching vehicles or cyclists.
Day Steady 25
25 lumens for 4.25 hours
This is a bright, non-flashing light for daytime
“to be seen” visibility.
Night Steady 5
5 lumens for 21 hours
This is a non-flashing light that is less bright for use
at night when ambient light is low. It is also great for
group rides.
*IMPORTANT: Check your local lighting laws. Flashing
lights are not allowed in all locations. Flare R does not
conform to the German road traffic regulation StVZO.
BT16_MANUAL_FlareR_USEN_FINALv5.indd 6 3/4/16 4:46 PM

Run Time Table
Mode Run time
(hours)
Low battery
strobe** (hours)
Day flash 5.75 +2
All-Day flash 10 +2
Night flash 23 +2
Day steady 4.25 +2
Night steady 21 +2
**Low Battery Strobe:
When the battery gets to 5% remaining charge,
the light will automatically switch to a 5-lumen
strobe mode and the status LED will begin blinking.
This will provide up to 2 hours of runtime. If the light
enters lower battery strobe, charge the light immediately
for 2 hours for full charge.
BT16_MANUAL_FlareR_USEN_FINALv5.indd 7 3/4/16 4:46 PM

Battery Level Indicator (Run time):
When the Flare R is switched on, the status LED in the
power button indicates the battery power remaining.
A bicycle without correct lights and reflectors might
be difficult for other people to see, and you might not
be able to see. If you can not see, or other people
can not see you, you could have an accident. Make
sure your lights operate correctly and that batteries
are charged.
WARNING
BT16_MANUAL_FlareR_USEN_FINALv5.indd 8 3/4/16 4:46 PM

Battery Level Status
Battery Level Indicator (Run time):
When the Flare R is switched on, the status LED in the
power button indicates the battery power remaining.
Button light color Power remaining
Green More than 25%
Red Between 5% and 25%
Blinking red** Less than 5%
Status LED
Main LED
WARNING
**Low Battery Strobe:
When the battery gets to 5% remaining charge,
the light will automatically switch to a 5-lumen
strobe mode and the status LED will begin blinking.
This will provide up to 2 hours of runtime. If the light
enters lower battery strobe, charge the light immediately
for 2 hours for full charge.
BT16_MANUAL_FlareR_USEN_FINALv5.indd 9 3/4/16 4:46 PM

Mounting
IMPORTANT: Ensure the light’s lens is oriented
perpendicular to the ground to optimize visibility.
BT16_MANUAL_FlareR_USEN_FINALv5.indd 10 3/4/16 4:46 PM

22.2
25.4
31.8
1
3
2
Accessories
This light is compatible with these optional mounting
systems. Please see your Bontrager retailer for details.
Bontrager helmet mount
(PN 428462)
Bontrager seat pack clip
(PN W528503)
Bontrager seat-stay
bracket (PN 418932)
Bontrager seat post
clamp (PN 418932)
Bontrager Sync bracket
(PN 418921)
BT16_MANUAL_FlareR_USEN_FINALv5.indd 11 3/4/16 4:46 PM

About this Manual
This is the manual for your Flare R.
Check for updates at bontrager.com.
BT16_FLARE_R_V3
BT16_MANUAL_FlareR_USEN_FINALv5.indd 12 3/4/16 4:46 PM