Bosch NKT 72 User manual

@BOSCH
INSTALLATION INSTRUCTION MANUAL
for
Bosch Electric Built-in Ceramic Cook-top
Models NKT 72 and NKT 92
MANUEL D'INSTALLATION
Surface de cuisson _lectrique en €_r.amique encastr_e
ModUles NKT 72 et NKT 92
BEFORE YOU BEGIN, READ THESE INSTRUCTIONS "COM-
PLETELY AND CAREFULLY.
VEUILLEZ LIRE ATTENTIVEMENT CE MANUEL AVANT DE
COMMENCER L'INSTALLATION.
rIMPORTANT: Save these instructions for the local electrical inspector's use
INSTALLER: Please leave this manual with owner for future reference.
OW_R: Please keep this manual for future reference.
IMPORTANT: Conservez ce manuel pour l'inspecteur 61ectrique local.
INSTALLATEUR: Veuillez remettre ce manuel au propri_taire de l'appareil
pour r_f_rence.
PROPRIETAIRE: Veuillez garder ce manuel et vous en servir pour r6f6rence.
800 520 00 /07.98

Table of Contents 3
Introduction
Tools You Will Need
power 'Requirements
Counter Preparation
Steps for Installation
Technical Data
Preparing the Location
for 30" Cook-Top
for 36" Cook-Top
Attaching Fastening Rails
Placing the Cook-Top
Electrical Supply
Electrical Connections
Final Check List
Schematic Wiring Diagrams
5
6
7
8
9
10
11
12
Table des mati_res Introduction
Les outils dont vous aurez besoin
Sp6cifications _lectriques requises
Preparation du comptoir
I_tapes de l'installation
Donn_es techniques
Pr6paration de l'emplacement, 30"
Pr6paration de l'emplacement, 36"
Installation des rails de fixation
Mise en place de la surface de cuisson
Alimentation en _lectricit6
Connexions _lectriques
Liste de v4rification finale
Sch4ma 61ectrique
14
15
16
17
18
19
20
21
22
23
2

Introduction
Please read these instructions COMPLETELY
AND CAREFULLY. They will save you time and
effort and help to ensure optimum cook-top
performance. Be sure to observe all WARNINGS.
These installation instructions are intended for use
by aqualified installer. In addition to these
instructions the cook-top shall be incralled:
•In the United States, in accordance with the
National Electric Code/State and Municipal codes
and/or local codes.
•In Canada, in accordance with Canadian Electric
Code C22.1-1atest edition/Provincial and Municipal
codes and/or local codes.
These shall be carefully followed at all times.
TOOLS YOU WILL NEED
The following tools are needed to install your new
cook-top:
Tape measure and straightedge or ruler
Pencil
Phillips screwdriver
Pliers
Wire cutters and wire stripper
1" hole saw
Hand or saber saw
POWER REQUIREMENTS
The cook-top must be supplied with the proper
voltage and frequency. The cook-top must be
connected to a three wire or four wire, single phase,
240 or 208 volt, 60 Hz AC only electrical supply
on a separate circuit fused on both side of the line.
A circuit breaker or time-delay fuse sized not to
exceed the circuit rating of the appliance specified
• on the serial/rating plate located on the bottom of
the cook-top is recommended.
The cook-top must be connected with copper wires
ONLY.
COUNTER PREPARATION
Counter space must be provided for installation of
your new cook-top. When choosing a location
consider the following IMPORTANT
CONSIDERATIONS:
•Cabinet storage space located above the
cook-top should be avoided, to eliminate the
risk of burns or fire caused by reaching over
heated surface units of the cook-top. If you
choose to install cabinet storage above the
cook-top, install a range hood that extends
out horizontally at least 5" (127 mm)
beyond the bottom front edge of the
cabinets.
• If you choose to install cabinet storage above
• the cook-top, do not store any item(s) that
could be of interest to children in the
• cabinets above the cook-top. Children •
climbing on the cook-top could be seriously
burned.
• If you choose to install cabinet storage above
the cook-top, cto not store heavy, hard
objects that if dropped could damage the
ceramic cooking surface in the cabinets
above the cook-top.
STEPS FOR INSTALLATION
The following pages provide a step by step guide
for installation of the cook-top arranged as
follows:
Technical Data
Preparing the Location, for 30" cook-top
Preparing the Location, for 36" cook-top
Attaching F_tening Rails
Placing the Cook-Top in its Location
Electrical Supply
Electrical Connections
Final Check List
It is recommended that you have the electrical
wiring and hook-up of your cook-top performed by
a qualified electrician. After installation is complete
have the electrician show you where the main
disconnect is and which of the circuit breakers/fuses
are for the cook-top.

Technical Data
NKT 72 series, (30", 4 element)
Dimensions, NK'F 72
a Height 4" 102 mm
b Width 30" 762 mm
c Depth 20U2" 521 mm
a •
Electrical Rating, NKT 72
Volts Hertz Amperes Watts
240 60 40 7900
208 60 28 6 000
NKT 92 series, (36", 5 element)
Dimensions, NKT 92
a Height 4" 102 mm
b Width 36" 914 mm
c Depth 201/_'' .. 521 mm a
Electrical Rating, NKT 92
Volts
240
208
Hertz
60
60
A_l_res Watts
_ 9 900
74O0

Preparing the Location
for 30", four Element Cook-Top
30"(762mm) rain
cabinet width
above cooktop
depth For minimum
cJearences
see note*
Lowercabinet depth: Openin
>25 (635 ram) for
combinationwith _- / .
downdraft fan ...._/2-1/2 (63.5mm)
>24 (610 ram) without
downdraft fan
box heightJ
rain
2-1/4"(57mm) counter
space both sides of
cutout from a combustible
surface Locate supply junction
box on wall 12"(305mm) or
more above the floor line
Work top:
The work top must have aminimum
thickness of 1". It must be level
and sealed along the wall to protect
against spilled liquid.
Cabinets:
Cabinets must resist temperatures
of up to 212"F (100"). This applies
in particular for veneers, edges, plastic
surfaces, glue and paint.
•Note: 24" rain. clearance if bottom of wood
or metal cabinet is protected by not less
than if4" flame retardant millborad
covered with not less than No. 28 MSG
sheet steel, 0.015" stainless steel, or 0.024"
aluminum or 0.020" copper.
30" rain. clearance between top of cooking
platform and bottom of unprotected wood
or metal cabinet.

Preparing the Location
for 36", five Element Cook-Top
36"(914mm) min
cabinet width
above ccoktop
35-1/4"(895mm)
width
13"(330mm)max
upper cabinet
depth For minimum
clearenoes
see note"
Lower cabinet depth:
>25"(635 mm)
for combination with
downdraft fan.
>24"(610 mm) without
downdraft fan
Burner box height
min
2-1/4"(57mm) counter
space both sides of
cutout from a combustible
surface Locatesupply junction
box on wall 12"(305mm) or
more above the floor line
Work top:.
The work top must have aminimum
thickness of 1". It must be level
and sealed along the wall to protect
against spilled liquid.
Cabinets:
Cabinets must resist temperatures
of up to 212°F (100°). This applies
in particular for veneers, edges, plastic
sufaces, glue and paint.
•Note: 24" min. clearance if bottom of wood
or metal cabinet is protected by not less
than t/4" flame retardant rfdllborad
covered with not less than No. 28 MSG
sheet steel, 0.015" stainless steel, or 0.024"
aluminum or 0.020" copper.
30'" min. clearance between top of cooking
platform and bottom of unprotected wood
or metal cabinet.

Attaching Fastening Rails
used for both NKT 72 and NKT 92 series
90*
To attach the fastening rails:
I. Mark the center as shown in drawing.
2. Align rails using notch.
3. Secure the rails tightly using screws.
Note: a. The top flange of rail must sit tightly
against the counter top.
b. If counter top is tiled, the lower
screws holes in the rails should be
used.
SPECIAL NOTE:
Use plugs or sleeves for screws or glue rails in
place, using a temperature resistant two component
adhesive which is suitable for bonding metal to
stone, when installation is in granite or marble
counter top.
Important:
•Do all counter top preparation, before
installing the cook-top. Be sure to clean area
after cutting and before installing cook-top.
Chips, and other debris from cutting of the
counter may impair the function of electrical
components.
•Seal the cut surfaces with silicone rubber,
heat resistant enamel or casting resin, to seal
the surface against moisture.

Placing the Cook-Top
1. Thread the cable through the cutout opening.
2. Gently place the cook-top into the cutout,
taking care to assure that cable does not
become pinched between the cook-top and the
counter cutout, and press in place so that
cook-top interlocks with rails.
Note: If installing on a tiled counter top, seal the
tile joints with silicone rubber.
NKT 92 series shown
SPECIAL NOTE:
Do not install the cooktop over a refrigerator,
dishwasher or washing roac!!he.

Electrical Supply
Before installing the cook-top have a qualified
electrician verify that your home is provided with
adequate electrical service and that the addition of
the cook-top will not overload the branch circuit
on which it is to be installed. A separate three-wire
or four-wire single phase, 240 or 208 Volt, 60 Hz,
40 Amp. branch circuit is required.
For hook-up of the cook-top you will need to have
an approved junction box installed where it will be
easily reached through the front of the cabinet where
the cook-top wilI be located. The cook-top has 3 feet
of conduit. DO NOT shorten the flexible conduit.
ELECTRICAL SHOCK HAZARD
• The electrical power to the cook-top branch
circuit must be shut off while line
( connections are being made.
•TO avoid risk of electrical shock, DO NOT
install cook-top if cooking surface is
broken.
• Electrical ground is required on this
appliance. The free end of the green and
yellow striped wire (the ground wire) must
be connected to asuitable ground. This
wire must remain grounded to the cook-top.
• If cold water pipe is interruptedby plastic,
non-metallic gaskets, union connections or
other insulating materials, DO NOT use for
grounding.
• DO NOT ground to a gas pipe.
•Do not have a fuse in the NEUTRAL or
GROUNDING circuit. A fuse in the
NEUTRAL or GROUNDING circuit could
result in an electrical shock.
• Check with a qualified electrician if you are
in doubt as to whether the appliance is
properly grounded.
Failure to follow these instructions could result in
serious injury or death.
WIRING REQUIREMENTS
When making the wire connections, use the entire
length of the conduit provided (3 feet)• The
conduit must not be cut.
Before making connections make sure the power is
off and read and observe the following:
1. A separate three-wire or fuur-wire, single
phase, 240 or 208 Volt, 60 Hz, 40 Amp. branch
circuit is required for the cook-top•
2. The cook-top must be Eonnected with COPPER
WIRE ONLY.
3. In the United States:
Wiring must conform to the National
Electrical Code, ANSI/NFPA No. 70 latest
edition• You can obtain a copy of the
National Electrical Code by writing:
National Fire Protection Association
Batterymarch Park
Quincy, MA 02269
In Canada:
Wiring must conform to Canadian Electrical
Code C22.1-1atest edition. You can obtain
copies of the Canadian Electrical Code by
writing:
Canadian Standards Association
178 Rexdale Boulevard
Rexdale (Toronto), Ontario, Canada
M9W IR3
4t Wire size (COPPER WIRE ONLY) and connec-
tions must be suitable for the rating of the
appliance (40 amps.) per National Electricai
Code requirements. The flexible armored cable
extending from the cook-top should be connec-
ted directly to the junction box.
5. The junction box should be located so as to
allow as much slack as possible between the
junction box and the cook-top so the cook-top
can be moved if servicing is ever required.
6. A U.L. listed conduit connector must be
provided at each end of the power supply
cable.

J
t
-i Electrical Connections
This appliance is manufactured with agreen and
yellow striped GROUND wire connected to the
cook-top chassis. After making sure that the power
has been turned off connect the flexible conduit
from the cook-top to the junction box using a U.L.
listed conduit connector, see figures A and B.
Figures A and B and the instructions provided
below present the most common way of
connecting the cook-tups. Your local codes and
ordinances, of course, take precedence to these
instructions. Complete electrical connections
according to local codes and ordinances.
Grounded neutral
Red wires
Cable from
power supply
Junction box
Twist-on
connectors
3-wire branch circuit
Refer to Figure A, where local codesallow the
connection of GROUND wire to the branch circuit
NEUTRAL (grey or white wire):
• If local codes permit, connect the green and
yellow striped GROUND wire from the
cook-top to the branch circuit NEUTRAL
wire (grey or white color wire).
• Connect the red and black leads from the
cook-top to the corresponding leads in the
junction box.
White wire
FigureA
Green wire
with yellow
stripes Cable from
cook-top
Cable from
power supply
Ungrounded neutral
Red wires
U.L.Listed conduit
connector
Junction box
Twist-on.
connectors
4-wire branch circuit
Refer to Figure B:
• Connect the green and yellow striped
GROUND wire from the cook-top to the
GROUND wire in the junction box (bare or
green color wire).
•Connect the red and black leads from the
cook-top to the corresponding leads in the
junction box.
• Place a twist-on connector on the end of the
NEUTRAL (grey or white) Wire.
Rare or
green wire
FigureB
Green wire
with yellow
stripes Cable from
cook-top
U.L,Listed conduit
connector
Blackwires
10