Bosch WTS86500GB User manual

1 2 3 4 5 6
Reduced temperature for deli cate fabrics ', for a longer drying time; e.g.
acrylic, polyamide, elastane or acetate silk.
ˎVV÷
Low Heat
Reduces creasing and prolongs the anti-cr easing phase after the
programme has finished; can be se lected in one of two levels.
ˎReduced Ironing
Indicators which show the programme seq uences.
Drying, Iron Dry, Cupboard Dry, End / Easy Iron.
Status indicators
Icc+cc\
Clean the fluff filter and/or air cooler unde r running water aPage 4/6.
Empty the condensation container.
Fill the water tank wit h distilled water aPage 9 .
Service indicators
4clean
.container
uwater tank
ˎMenu For selecting the set tings.
ˎ-/+ For changing all the settings in th e display panel.
Electronic start
timer
End of the programme after ... (dependi ng on the programme selected, e.g. 1:54h a2h;
you can always sel ect up to the ne xt full hour).
1 -24 hrs
3Signal There are four buzzer volume se ttings: 0 (off), 1 (quiet), 2 (normal), 3 (loud), 4 (very lo ud). 0, 1, 2, 3, 4
#Appliance lock
(depending on the
model)
Provides protection against u nintentional changes to the func tions set
(press and hold the Menu button for 5 seconds).
On-Off
9Fine adjustment
of the drying result
The drying result (e.g. Cupboard Dr y) can be adjusted over three levels (1 - max. 3) for the
Cottons,Easy-Care,/Mixed Load and Super Quick 40’ programmes apresetting = 0.
After one of these programmes has be en finely adjusted, the setting is retained f or the others.
0, 1, 2, 3
Spin speed The spin speed that was used in the washing machine;
for more precise indic ation of the projected dry ing duration only.
600-1800
²... and adapt to individual requ irements
Never operate the dryer if it is damaged.
Inform your after-sales service. Inspecting
the dryer
Sorting and loading laundry
Remove all objects from pockets.
Pay particular attention to cigarette lig hters.
The drum must be empty before filling.
If necessary, fill the water tank for
Steam Dry / Steam Refresh prog rammes aPage 8.
See programme overview on pa ge 7.
See also separate instructions for “basket for woollens”
(depending on the model)
Your new dryer
Congratulations! - You have chos en a modern, high-quality domestic
appliance from Bosch.
A distinctive feature of the condensation d ryer is its low energy
consumption.
Every dryer which leaves our factory is carefully checked to ensure
that it functions correctly and is in perfect condition.
Should you have any questions, our after-sales service will be pleased
to help.
Environmentally-responsible disposal
Dispose of packaging in an environmentally-responsible manne r.
This appliance is designated according to European directive 2002/96/EC which governs waste e lectrical and electronic
equipment (WEEE).
This directive provides the frame work for the EU-wide collection an d
reuse of used appliances.
For further information about our products , accessories, spare parts
and services, please visit: www .bosch-home.com
Intended use
Contents Page
ʋPreparation . . . . . . . . . . . . . . . . . . . . . . 2
ʋSetting the programmes . . . . . . . . . . . . . 2
ʋDrying . . . . . . . . . . . . . . . . . . . . . . . . 3/4
ʋNotes on laundry . . . . . . . . . . . . . . . . . . 5
ʋCleaning and care . . . . . . . . . . . . . . . . . . 6
ʋOverview of programmes . . . . . . . . . . . . 7
ʋShort spin / Refresh . . . . . . . . . . . . . . 8/9
ʋInstallation . . . . . . . . . . . . . . . . . . . . . . 10
ʋFrost protection / Transport . . . . . . . . . .10
ʋTechnical data . . . . . . . . . . . . . . . . . . . 11
ʋOptional accessories . . . . . . . . . . . . . . .11
ʋWhat to do if... / After-sales service . . . .12
ʋSafety instructions . . . . . . . . . . . . . . . . 13
Preparing for installation, see pa ge 8
Selecting and adjusting the programme
Additional functions
Select the drying progra mme ...
Press the Start/Stop bu tton
Only if your hands are d ry.
Only hold the plug by the plug
casing.
Connecting the
mains plug
Display panel Programme selector
All buttons are sensitive,
a light touch is enough!
3
2
1
Drying / Short spin /
Refresh
Drying Emptying condensation
Empty the container after each dry ing cycle, not during drying!
1. Remove the container, holding it level.
2. Pour out condensation.
3. Push the .container back in until i t clicks into place.
Cleaning the fluff filter
1. Open the door, remove the filte r and fold open.
2. Remove the fluff (by wiping the filter with you r hand).
3. Close the filter, insert it again and close the doo r.
4. Remove fluff from the door and th e area around it.
Very dirty or blocked filters should be rinsed under warm
water, and then dried thoroughly.
Clean the filter in the water tank if it is dirty
1. Remove the condensation tank.
2. Remove the filter.
3. Clean the filter under running water.
4. Re-insert the filter and push in the c ondensation tank until it clicks into
place.
Switching off the dryer
Turn the programme selector to Off.
Do not leave damp laundry in the dryer .
Removing the laundry
The automatic Easy Iron function moves the drum at certain intervals. The load remain s loose and soft for
an hour (or two hours if you manually sele ct the cReduced Ironing function, depending on the model.)
Information on laundry ...
Labelling of fabric s
Follow the manufacturer's care information.
(Drying at normal temperatur e.
'cDry at a low temperature aselec tcVV÷Low Heat as well.
)cDo not machine dry.
Do not tumble-dry the foll owing fabrics:
– Airtight fabrics (e.g. r ubber-coated fabrics).
– Delicate materi als (silk, curtains mad e from synthetic material) ath ey may crease.
– Oil-stained laundry.
Drying tips
– To ensure a consistent result, sort the laundry by fabric type and drying programme.
– Close zips, hooks and eyes, and do up any buttons.
Tie belts, apron strings etc. together.
– Do not overdry easy-care lau ndry arisk of creasing
Allow laundry to finish drying in the a ir.
– Do not iron laundry immediately after drying, fold items up and leave for a while
athe remaining moisture will th en be distributed evenly.
– The d rying result depends on the type of water used during washing. aFine adjustment
of the drying result aPage 1/2.
– Knitte dfab rics (e.g. T-shirts, jerseys) often shrink slightly the first time they are tumble -dried.
aDo not select the Extra Dry programme.
– Starched laundry i s not always suitab le for dryers astarch leaves behind a coating that
adversely affects the drying op eration.
– When washing laundry that is to be tumb le-dried afterwards, dose the fabric s oftener
according to the manufactu rer's instructions.
– With a small load, use the Ti med Program.
Tips for Steam Dry / Steam Refresh
– Use your dryer for unwrinkling and refreshi ng fabrics.
– Short spin cycle for reduc ing creasing.
– Refresh cycle for reducinging od ours from fabrics.
Do not use Steam Dry / Steam Refresh fo r the following fabrics:
– Wool, leather, fabrics with meta l, wooden or plastic parts.
– Wax and oil jackets .
– Sort the laundry by colour and put on separate sh ort Steam Dry / Steam Refresh cycles
to prevent the colours from bleeding.
– These programmes do not rem ove stains astains must be treate d and removed
beforehand.
– For best results, so that the laundry will have as few creases as possible, remove eac hi tem
immediately after the programme has finished and hang on a hanger to fin ish drying.
Pull clothes into shape i f required.
Environmental protecti on / Energy-saving tip s
– Before drying, spin the laundr y thoroughly in the washing machine athe higher the spin
speed, the shorter the drying time w ill be (consumes less energy), also spin easy- care
laundry.
– Use the maximum recommended capacity, but do not exceed it
aPage 7, “Programme overview”.
– Make sure the room is well ventilated during drying.
– Clean the fluff filter after e ach drying cycle aPage 4.
– Keep the air cooler clea n aPage 6 “Cleaning and care”.
– Keep the supply of c ool air unobstructed aDo not cove r or block the cooling grill.
Condensation container
Control panel
Air inlet
Fluff filter
Drum
Cleaning and care
Dryer housing, co ntrol panel, air coo ler, moisture sensors
– Wipe with a soft, damp cloth.
– Do not use h arsh cleaning agents and s olvents.
– Remove detergent and clean ing agent residue immediately.
– During drying, water may collec t between the door and seal. This does not affect your
dryer's functions in any way.
Clean the protective fil ter 5 - 6 times a year
or if 4flashes after the fluff filter has been cl eaned.
Air cooler / Protective filter
When cleaning, only remove the prote ctive filter.
Clean the air coo ler behind the protectiv e filter once a yea r.
– Allow the dryer to cool.
– Residu al water may leak out, so place an abso rbent towel
underneath the maintenance door.
1. Unlock the maintenanc e door.
2. Open the maintenance door fully.
3. Turn both locking leve rs towards each anoth er.
4. Pull out the protective fi lter/air cooler.
Do not damage the protective filter or a ir cooler.
Clean with warm wat er only. Do not use a ny hard or sharp- edged
objects.
5. Clean the air cooler thoroughly.
Allow to drip dry.
6. Clean the seals.
7. Re-insert the protective filter/air cooler,
with the handle facing down.
8. Turn back both locking levers.
9. Close the maintenance door until the lock c licks into place.
Moisture senso rs
The dryer is fitted w ith stainless steel moisture se nsors. The sensors
measure the level of moisture in the laundry. After a long period of
operation, a fine layer of limescale may fo rm on the sensors.
1. Open the door and clean the m oisture sensors with a damp spong e
which has a rough surface.
Do not use steel wool or abrasive material s.
Cover for steam nozzle in the drum
After lengthy operat ion, limescale and fluff may accumulat e on
the cover of the steam nozzle. Clean regularly:
1. Open the door and remove the cover with a screw driver.
Clean the cover under running wate r.
2. Push and click the protec tive cap back in place.
Cover for
steam nozzle
Air cooler
Programme end once \lights up in the display.
Interrupt programme removing or adding laundry.
The drying cycle can be interrupte d for a brief period so that laund ry may be added or removed.
The selected programme must then be c ontinued until it is finished.
Hot steam may escape during the Stea m Drying / Steam Refresh programmes.
1. Open the door. The drying cycle is paused.
2. Remove or add laundry and close the door.
3. I f required, select a new p rogramme and additional functions.
4. Press the Start/Stop button. The remaining time is updated after a few minutes.
Water tank
filling hole
with filter
Only when switched off!
Read these instructions bef ore operating the dryer.
Observe the safety instructions on page 13.
Caution - risk of scalding.
ʋFor domestic use only.
ʋOnly to be used for drying, refreshing or unwrinkling
fabrics that have been washe d with water.
Do not leave children
unsupervised near the dryer.
Keep pets away from the dryer.
The dryer can be operated by children 8 years old
and older, by persons with reduce d physical,
sensory or mental abilities and b y persons with
insufficient experience or knowledge if they are
supervised or have been instructed in its use
by a responsible adult.
7
Programme overview see also pages 5 and 8
Sort the laundry according to type of textile and fabric. Fabrics must be suitable for tumble drying. After drying...
c
iron laundry

lightly iron laundry
@c
do not iron laundry
c
mangle laundry
PROGRAMMES TEXTILE TYPE AND INFORMATIO N **Cottons max. 8 kg Hard-wearing fabric s, boil-resistant fabrics ma de of cotton or linen. **Easy-Care max. 3.5 kg Non-iron laundry made of s ynthetic fibres and blended fabric, easy-care cotton. **/Mixed Load max. 3 kg Mixed items of laundry madeofco tton and synthetics (Mix).
Iron Dry c÷@c Fabrics suitable for ironing (iron fabric s in order to avoid creasing). Cupboard Dry @Single-layer fabrics. *Extra Dry @Fabrics made of thic k, multilayered items of cloth ing.
wSteam Dry For smoothing hard-wearing and easy-care fabrics. Steam smoo ths the fabrics. Minimum Iron Daily Load max. 2.5 kg F urther information aPage 8. Minimum Iron Shirt max. 1.5 kg HSteam Refresh For freshening hard-wearing and eas y-care fabrics. Steam freshens up the fabrics. Business max. 1.5 kg Further information aPage 8. Freshen up max. 1.0 kg ZSportswear max. 1.5 kg Fabrics with membrane coati ng, water-repellent fabrics, functional clothin g, fleece fabrics (dry jackets/trousers with
removable internal lini ng separately).
Woollens Finish max. 3 kg Woollen fabrics suitable for washing machines. F abricsb ecome fluffier but not dry.
Remove fabrics once the programm e has ended and allow to dry.
ASuper Quick 40’ max. 2 kg
Laundry made of synthetic fibre s,c otton or blended fabrics (for example) that needs to bedried quickly. The va lues may
differ from the those specified depe nding on the type of fabric, mixture of laundry to be dried, re sidual moisture in the fabric and loading capac ity.
Timed Programm es warm max. 3 kg Pre-dried, multi-layered, sensitive fabrics ma de of acrylic fibres, or separate small items of laundry.
Also for subsequent drying.
*for Cottons and Easy-Care programmes only
**Dryness levels can be selected in dividually aExtra Dry, Cupboard Dry and Iron Dry (depending on the mo del).
Degree of dryness can be finely adjusted; multi-layered textiles requi re a longerd rying time than single-layered items of clothing. Recommendation: Dry separately.
9202 / 9000746180 *746180* Robert Bosch Hausgeräte GmbH
Carl-Wery-Str. 34
D-81739 Munich/Germany
WTS86500GB

8
Steam Drying - Steam Refresh
Steam programmes for un wrinkling or refreshi ng
– Your dryer has un wrinkling and refreshing programmes that can be used for reducing
odours and minimising creasing in dry fabrics. Steam smooths and fre shens up items of
clothing.
– Sorting the l aundry according to size, w eight, fabric and colour i s necessary.
– Only use Sho rt spin/Refresh for fabrics with the s ame properties.
– During steam ge neration (required), additional noises may o ccur.
– The result of refre shing and unwrinkling may vary depending on the type of fabric, size of
the load and programme sel ected.
– After unwrinkli ng or refreshing, all fabrics must be removed immediately and hung crease-
free on a hanger or a washing line for 15 minutes.
Programmes
Please observe the treatment symbols and manufacturer's instructions on the fabrics.
Do not use Short spin/Refresh for fabrics m ade of wool, leather, containing metal or
wooden parts as well as wax and oi l jackets!
Do not use any dryer cleaning sets!
ʑwSteam Dry
Minimum Iron Shirt
Suitable for easy-care fabrics, e.g. formal s hirts. Fabrics are smoothed. You can e xpect
optimum results if “non-iron” appears on the c are label. After the programme has finished,
the items must be removed immediately and hung crease-free on a hanger or washing line
for 15 minutes. The programme is for up to 5 formal shirts.
Minimum Iron Daily Load
Suitable for hard-wearing cotton fabrics, e.g. bed l inen, tablecloths or formal shirts. Fabrics
are smoothed. You can expect optimum r esults if “non-iron” appears on the care label. After
the programme has finished, the items must be removed immediately and hung crease-free
on a hanger or washing line for 15 minu tes. The programme is for up to 5 form al shirts or
1 to 2 larger items.
ʑHSteam Refresh
Business
Suitable for refreshing suits, jackets and trousers, or dry-clean items th at cannot be washed
in the washing machine asee the care label. The programme only refreshes fabrics and
does not clean them. After the end of the programme, the items must b e removed
immediately. Programme for 1 suit or 1 to 2 smalle r items.
Freshen up
Suitable for refreshing casual wear ma de of cotton or artificial fibres. Fabrics m ust be
suitable for dryers asee the care label. The programme refreshes fabrics only, and does
not clean them. After the programme has finished, the fabrics must be remo ved
immediately. Programme for 1 pullover, 2 pairs of trousers or formal shirts.
9
Steam Drying - Steam Refresh
Your water tank empties auto matically after the programme has finished.
Cleaning is therefore not required
Filling the wate r tank:
Fill the dryer's water tank with distilled water before eve ry Steam Dry - Steam Refresh cycle.
1. Move the programme selector to Steam Dry
or Steam Refresh.
The usymbol appears in the display.
2. Remove the con densation tank comple tely.
Before every Steam Dry - Steam Refresh cycle, fill the wate r tank with
distilled water only. Do not use tap water, condensation or additives.
3. Fill the water tank. Use the jug suppl ied.
If the water tank filter is dirty ac lean the filter in the water tank.
See page 4.
4. Pour the distilled wat er into the filling hole on t he water tank,
until the usymbol g oes out on the displa y panel.
If drying the recommend ed load, approximately 250 to 300 ml of d istilled
water is used in the Steam Dry - Steam Refresh programmes.
5. Insert the condensation contai ner all the way.
6. Start the Steam Dry or Steam Refresh pro gramme.
10
Installation
– Scope of delivery: dryer, installa tion and instruction manual, jug, basket for woolle ns
(depending on the model).
– Check dryer for transport d amage.
– The dryer is heavy. Do not attempt to lift it on your own.
– Be careful to avoid shar p edges.
– Do not install i na room where there is a risk of freezing. Freezing water may cause damage.
– If in doubt, have t he appliance connected by a specialist.
– Do not lift the dryer by protruding parts (e.g . the door) - risk of breakage.
Setting up the d ryer
– The appliance plug must always be accessible.
– Ensure that the appliance is installed on a clean , level
and firm surface.
– Keep the cooling grille on the fr ont of the dryer
clear.
– Keep the area around t he dryer clean.
– Level the dryer usin g the threaded feet.
Use a spirit level.
– Do not remove the threaded feet under any
circumstances.
Mains conn ection see safety information aPa ge 13.
– Connect to an AC earthed socket. If in doubt, have the socket checked by a specialist.
– The mains voltage and the voltage shown onthe rating plate (aPage 11) must be the same.
– The connected load a nd necessary fuse protection are specified on the rating p late.
Frost protection / Transport
Preparation
1. Empty the condensation container aPage 4.
2. Select any programme using the programme selector.
3. Press the Start/Stop button acondensatio n is pumped into the container.
4. Wait 5 min., and then empty th e condensation container again.
5. Turn the programme selector to Off.
The water tank mu st not contain any dis tilled water. If necessary, ru n the Steam/Refresh p rogramme.
1.
Remove all accessories
from the drum.
The drum must be empty.
Make sure that the air inlet
remains unobstructed
Clean and level
Do not install the dryer behi nd a door or sliding
door, which could prevent o r restrict opening of the
dryer door. This will prevent c hildren from locking
themselves in and putting their lives in danger.
2.
Do not operate the dryer if there
is a danger of frost.
11
Technical data
ʠDimensions (DxWxH) 60 x 60 x 85 cm (adjustable hei ght)
Weight approximately 43.5 kg
Max. capacity 8 kg
Condensation container 4.0 l
Water tank approx. 0.4 l
Connection voltage 220-240 V
Connected load max. 2800 W
Fuse protection 13 A
Ambient temperature 5 - 35 °C
Product number
Production number Inside of door
The rating plate can be found on the back of the dryer.
ʠConsumption ra tes These are guide values determined und er standard
conditions.
Spin speed in rpm
(residual moisture)
Drying time
in min.**
Energy
consumption
in kWh**
Cottons 8 kg
Cupboard Dry* 1400 (approx. 50 %) 105 3.74
1000 (approx. 60 %) 122 4.49
800 (approx. 70 %) 139 5.17
Iron Dry* 1400 (approx. 50 %) 83 2.24
1000 (approx. 60 %) 100 3.44
800 (approx. 70 %) 117 3.86
IEasy-Care 3.5 kg 1000 39 1.05
Cupboard Dry* 800 (approx. 40 %) 42 1.35
600 (approx. 50 %) 51 1.65
*Test programme to DIN EN 61 121
**The values may differ from those given, depending on overvoltage and undervoltage, the
type of fabric, composition of the laundry to be dried, the residual moisture in the fabric and
the size of the load.
ʠDrum interior ligh t (bulb E14, 25 W)
The drum is illuminated after the doo r is opened or closed, and after the programme h as
started. The light goes out automatically. To change the bulb aPage 12.
Optional accessories (order from theafter-sales s ervice using the order number)
Connecting kit for con densation outlet
The condensation is drained off immediate ly via a hose.
Washer-dryer stack connec tion set
The dryer can be stacked on top of a suitable washing machine of the same depth and width,
to save space. The dryer must be secured to the washing machine with this connection set.
With pull-out worktop: WTZ 11300
Installation undernea th the worktop
Instead of the appliance covering plate, you must have a metal cover fitted by a special ist.
WTZ
1110
WTZ
11310
WTZ
10290
12
What to do if...
If you cannot rectify a fault yourself (e.g. switching off/on), please contact our a fter-sales
service. We will always find an appropr iate solution and will avoid unnecessary visits by
engineers. Trust the e xpertise of the manufact urer and rest assured tha t the repair will be
carried out by trained service te chnicians using original spare parts. The contact details of your
local after-sales se rvice can be found in the e nclosed after-sales service d irectory, or by
calling one of these numbers:
–GB 0844 8928979 (Calls from a BT landline will be charged at up to 3 pence per minute.
A call set-up fee of up to 6 pence may a pply.)
–IE 01450 2655
When contacting the aft er-sales service, please quot e the appliance's product num ber (E no.)
and production num ber (FD) (see the inside of the door).
Set the programme selector to Off and remove the app liance plug from the sock et.
ʠThe Start/Stop indicator light
does not come on.
Mains plug plugged in?
Programme selected?
ʠThe āsymbol and Start/Stop
indicator light are flash ing.
Empty the co ndensation container aPage 4.
Check the condensati on outlet hose, if applicabl e (kink).
ʠThe 4symbol and Start/Stop
indicator light are flash ing.
Clean the air cooler aP age 6 “Cleaning and care”. Clean the
fluff filter aPage 4.
ʠThe usymbol flashes. Is the water tank empty?
Filling with distil led water aPage 9.
The filter in the water tank may have become dirty.
If so, clean the filter in the water tank aPage 4 .
ʠThe Steam Dry - Steam Refresh
does not start.
ʠDryer does not start. Has the Start/Stop butt on been pressed? Is the door closed?
Programme set?
Ambient temperature grea ter than 5 °C?
ʠWater is leaking out. Make sure the dryer is level.
Clean the air cooler seal.
ʠThe door opens by itself. Push the door closed until you hear it click into pla ce.
ʠItems crease even though the
Steam Dry - Steam Refresh
programme has been selected.
Laundry load exceeded?
Remove articles of clothing immed iately after the end of the
programme, hang up an d pull into shape.
ʠCreasing. Laundry loa d exceeded?
Remove articles of clothing immed iately after the end of the
programme, hang up an d pull into shape.
Unsuitable programme selected aPage 7.
ʠDrying result is not satisfactory
(laundry feels too damp).
Warm laundry feels damper than it actually is.
The selected program me does not suit the load. Use another
drying programme or, in addition, select the time programm e
aPage 7.
Use fine adjustment for the drying result aPage 1/2.
Fine layer of limescale on the humidity sensors
aClean the humidity sensors aPage 6.
Programme termination, e.g. tank full, mains power supply
failure, door open or maximum drying time reached.
ʠDrying time too long. Rinse the fluff filters under running water aPage 4.
Insufficient supply of air aensure that air can circu late.
Air inlet possibly blocked aClear inl et aPage 10.
Ambient temperature higher than 35 °C aventilate the room.
ʠThe humidity in the room increases
significantly.
Make sure the room is sufficiently ventilated.
ʠOne or more programme status
indicator lamps are fla shing.
Clean the filter and air cooler unde r running water aPage 4/6.
Check the inst allation conditions aPage 10.
Switch off, allow to cool, swi tch on again and resta rt the
programme.
ʠThe interior light (depe nding on the
model) does not work.
Unplug the appliance plug, fold back the cover cap on the inside
above the door (using a Torx 20 screwdriver)
and replace the bulb. Close the cover cap.
13
Safety instructions
Emergency – Pull the appliance plug out of the socket immediately or disconnec t the fuse.
ONLY use the
dryer...
– in rooms inside the house.
– for drying or unwrinkling/ref reshing fabrics.
The dryer must
NEVER...
– be used for purposes other than those descri bed above.
– be modified in t erms of its technology or proper ties.
Hazards – The dryer must not be used by children or persons w ho have not been
instructed in its use.
– Do not leave children unsupervised near the dryer.
– Keep pets away fro m the dryer.
– Remove all objects from po ckets,
and lighters in particular arisk of exp losion.
– Do not l ean or sit on the door arisk of tipping.
– Open the door carefully. Hot steam may esc ape. The clothes and drum may
be hot arisk of burns.
Installation – Secure loose leads or hoses, oth erwise there is a risk of tripping.
– Below 0 °C th ere is a possibility o f frost damage.
Mains
connection
– Connect the drye r according to specifications to an AC earthed soc ket,
otherwise it cannot be guaranteed that the appl iance is completely safe.
– The cable cross-section must be sufficient.
– Only use earth-leakage circuit breakers with the following symbol:
– The appliance plug and so cket must be compatible.
– Do not us e multiple plugs/connectors and/or extension cables .
– Do not touch or hold the appliance plug with wet hands
arisk of electric shock.
– Never pull the appliance plu g out of the socket by its cable.
– Do not da mage the mains l ead arisk of electric shock.
Operation – Only laundry must be loaded into the drum.
Before switching on the dryer - check the contents.
– Do not use the dryer if the laundry has been i n contact with solvents, oil, wax,
grease or paint (e.g. hair setting spray , nail polish remover, stain remover,
cleaning solvent, etc.) afire/explosion ha zard.
– Hazard caused by d ust (e.g. coal dust, flour): do not use the dryer
arisk of explosion.
– Do not put l aundry containing foamed material/rubber in the dryer aelastic
material may be destroyed and the d ryer may be damaged due to possible
deformation of the foamed material.
– Switch off the dryer once the programme has ended.
– For unwrinkling/refreshing fabrics, use distilled water only. Do not use
condensation, tap water or ad ditives.
– Distilled/condensation wate r is not for drinking.
Defect – Do not use the dryer if it is defective or if you sus pect that it is.
Repairs must only be car ried out by the after-sales servic e.
– Do not use a dryer w ith a faulty mains lead. To p revent risks, a faulty mains
lead must only be replaced by the after-sales service.
– Before changing the bulb of the interior light make absolutely sure you have
pulled the appliance plug from the s ocket arisk of electric shock.
Spare parts – Only use genuine spare parts and accessori es for safety reasons.
Disposal – Dryer: unplug th e appliance plug, then cut the mains lead from the appliance.
Dispose of the dryer at an approved pu blic disposal facility.
– Packaging: keep all packaging out of reach of babies a nd children.
adanger of suffocation.
– All materials are e nvironmentally safe and recyclab le. Dispose of in an
environmentally-responsible manner.
Dryer
en Instruction man ual

1 2
Reduced temperature for delicate fabrics ', for a longer drying time; e.g.
acrylic, polyamide, elastane or acetate silk.
ˎVV÷
Low Heat
Reduces creasing and prolongs the anti-creasing phase after the
programme has finished; can be selected in one of two levels.
ˎReduced Ironing
Indicators which show the programme sequences.
Drying, Iron Dry, Cupboard Dry, End / Easy Iron.
Status indicators
Icc+cc\
Clean the fluff filter and/or air cooler under running water aPage 4/6.
Empty the condensation container.
Fill the water tank with distilled water aPage 9.
Service indicators
4clean
.container
uwater tank
ˎMenu For selecting the settings.
ˎ-/+ For changing all the settings in the display panel.
Electronic start
timer
End of the programme after ... (depending on the programme selected, e.g. 1:54h a
you can always select up to the next full hour).
3Signal There are four buzzer volume settings: 0 (off), 1 (quiet), 2 (normal), 3 (loud), 4 (very l
#Appliance lock
(depending on the
model)
Provides protection against unintentional changes to the functions set
(press and hold the Menu button for 5 seconds).
9Fine adjustment
of the drying result
The drying result (e.g. Cupboard Dry) can be adjusted over three levels (1 - max. 3) f
Cottons,Easy-Care,/Mixed Load and Super Quick 40’ programmes apre
After one of these programmes has been finely adjusted, the setting is retained for th
Spin speed The spin speed that was used in the washing machine;
for more precise indication of the projected drying duration only. ²... and adapt to individ
Never operate the dryer if it is damaged.
Inform your after-sales service.
Sorting and loa
Remove all objects from pockets.
Pay particular attention to cigarette lighters.
The drum must be empty before filling.
If necessary, fill the water tank for
Steam Dry / Steam Refresh programmes aPa
See programme overview on page 7.
See also separate instructions for “basket for w
(depending on the model)
Your new dryer
Congratulations! - You have chosen a modern, high-quality domestic
appliance from Bosch.
A distinctive feature of the condensation dryer is its low energy
consumption.
Every dryer which leaves our factory is carefully checked to ensure
that it functions correctly and is in perfect condition.
Should you have any questions, our after-sales service will be pleased
to help.
Environmentally-responsible disposal
Dispose of packaging in an environmentally-responsible manner.
This appliance is designated according to European directive 2002/96/EC which governs waste electrical and electronic
equipment (WEEE).
This directive provides the framework for the EU-wide collection and
reuse of used appliances.
For further information about our products, accessories, spare parts
and services, please visit: www.bosch-home.com
Intended use
Contents Page
ʋPreparation . . . . . . . . . . . . . . . . . . . . . . 2
ʋSetting the programmes . . . . . . . . . . . . . 2
ʋDrying . . . . . . . . . . . . . . . . . . . . . . . . 3/4
ʋNotes on laundry . . . . . . . . . . . . . . . . . . 5
ʋCleaning and care . . . . . . . . . . . . . . . . . . 6
ʋOverview of programmes . . . . . . . . . . . . 7
ʋShort spin / Refresh . . . . . . . . . . . . . . 8/9
ʋInstallation . . . . . . . . . . . . . . . . . . . . . . 10
ʋFrost protection / Transport. . . . . . . . . . 10
ʋTechnical data . . . . . . . . . . . . . . . . . . . 11
ʋOptional accessories . . . . . . . . . . . . . . . 11
ʋWhat to do if... / After-sales service . . . . 12
ʋSafety instructions . . . . . . . . . . . . . . . . 13
Preparing for installation, see page 8
Selecting and adjusting the
Additional functions
Select the dry
Press the Only if your hands are dry.
Only hold the plug by the plug
casing.
Conn
m
Display panel Programme selector
All buttons a
a light touch .c('cacVV÷)caaaaaaaaaaaaa4\
Read these instructions before operating the dryer.
Observe the safety instructions on page 13.
Caution - risk of scalding.
ʋFor domestic use only.
ʋOnly to be used for drying, refreshing or unwrinkling
fabrics that have been washed with water.
Do not leave children
unsupervised near the dryer.
Keep pets away from the dryer.
The dryer can be operated by children 8 years old
and older, by persons with reduced physical,
sensory or mental abilities and by persons with
insufficient experience or knowledge if they are
supervised or have been instructed in its use
by a responsible adult.
c@c c
/c÷@c @@waHaZAa

3 4
'ˎVV÷ˎIcc+cc\aa4.uˎˎa2h; 1 -24 hrs
3ry loud). 0, 1, 2, 3, 4
#On-Off
9) for the
/aresetting = 0.
the others.
0, 1, 2, 3
600-1800
²ividual requirements
Inspecting
the dryer
loading laundry
aPage 8.
r woollens”
ʋʋʋʋʋʋʋʋʋʋʋʋʋthe programme
drying programme ...
e Start/Stop button
onnecting the
mains plug
s are sensitive,
ch is enough!
3
2
1
Drying / Short spin /
Refresh
Drying Emptying condensation
Empty the container after each drying cycle, not during drying!
1. Remove the container, holding it level.
2. Pour out condensation.
3. Push the .container back in until it clicks into place.
Cleaning the fluff filter
1. Open the door, remove the filter and fold open.
2. Remove the fluff (by wiping the filter with your hand).
3. Close the filter, insert it again and close the door.
4. Remove fluff from the door and the area around it.
Very dirty or blocked filters should be rinsed under warm
water, and then dried thoroughly.
Clean the filter in the water tank if it is dirty
1. Remove the condensation tank.
2. Remove the filter.
3. Clean the filter under running water.
4. Re-insert the filter and push in the condensation tank until it clicks into
place.
Switching off the dryer
Turn the programme selector to Off.
Do not leave damp laundry in the dryer.
Removing the laundry
The automatic Easy Iron function moves the drum at certain intervals. The load remains loose and soft for
an hour (or two hours if you manually select the cReduced Ironing function, depending on the model.) ('cacVV÷)caaaaaaaaaaaaa
Condensation container
Control panel
Air inlet
Fluff filter
Drum 4
Cover for
steam nozzle
Air cooler
Programme end once \lights up in the display.
Interrupt programme removing or adding laundry.
The drying cycle can be interrupted for a brief period so that laundry may be added or removed.
The selected programme must then be continued until it is finished.
Hot steam may escape during the Steam Drying / Steam Refresh programmes.
1. Open the door. The drying cycle is paused.
2. Remove or add laundry and close the door.
3. If required, select a new programme and additional functions.
4. Press the Start/Stop button. The remaining time is updated after a few minutes.
Water tank
filling hole
with filter
ʋʋ
c@c c
/c÷@c @@waHaZAa

56
'ˎVV÷ˎIcc+cc\aa4.uˎˎa3#9/a²aʋʋʋʋʋʋʋʋʋʋʋʋʋ.cInformation on laundry ...
Labelling of fabrics
Follow the manufacturer's care information.
(Drying at normal temperature.
'cDry at a low temperature aselectcVV÷Low Heat as well.
)cDo not machine dry.
Do not tumble-dry the following fabrics:
– Airtight fabrics (e.g. rubber-coated fabrics).
– Delicate materials (silk, curtains made from synthetic material) athey may crease.
– Oil-stained laundry.
Drying tips
– To ensure a consistent result, sort the laundry by fabric type and drying programme.
– Close zips, hooks and eyes, and do up any buttons.
Tie belts, apron strings etc. together.
– Do not overdry easy-care laundry arisk of creasing
Allow laundry to finish drying in the air.
– Do not iron laundry immediately after drying, fold items up and leave for a while
athe remaining moisture will then be distributed evenly.
– The drying result depends on the type of water used during washing. aFine adjustment
of the drying result aPage 1/2.
– Knitted fabrics (e.g. T-shirts, jerseys) often shrink slightly the first time they are tumble-dried.
aDo not select the Extra Dry programme.
– Starched laundry is not always suitable for dryers astarch leaves behind a coating that
adversely affects the drying operation.
– When washing laundry that is to be tumble-dried afterwards, dose the fabric softener
according to the manufacturer's instructions.
– With a small load, use the Timed Program.
Tips for Steam Dry / Steam Refresh
– Use your dryer for unwrinkling and refreshing fabrics.
– Short spin cycle for reducing creasing.
– Refresh cycle for reducinging odours from fabrics.
Do not use Steam Dry / Steam Refresh for the following fabrics:
– Wool, leather, fabrics with metal, wooden or plastic parts.
– Wax and oil jackets.
– Sort the laundry by colour and put on separate short Steam Dry / Steam Refresh cycles
to prevent the colours from bleeding.
– These programmes do not remove stains astains must be treated and removed
beforehand.
– For best results, so that the laundry will have as few creases as possible, remove each item
immediately after the programme has finished and hang on a hanger to finish drying.
Pull clothes into shape if required.
Environmental protection / Energy-saving tips
– Before drying, spin the laundry thoroughly in the washing machine athe higher the spin
speed, the shorter the drying time will be (consumes less energy), also spin easy-care
laundry.
– Use the maximum recommended capacity, but do not exceed it
aPage 7, “Programme overview”.
– Make sure the room is well ventilated during drying.
– Clean the fluff filter after each drying cycle aPage 4.
– Keep the air cooler clean aPage 6 “Cleaning and care”.
– Keep the supply of cool air unobstructed aDo not cover or block the cooling grill.
Cleaning and care
Dryer housing, control panel, air cooler, moisture sensors
– Wipe with a soft, damp cloth.
– Do not use harsh cleaning agents and solvents.
– Remove detergent and cleaning agent residue immediately.
– During drying, water may collect between the door and seal. This does not affect your
dryer's functions in any way.
Clean the protective filter 5 - 6 times a year
or if 4flashes after the fluff filter has been cleaned.
Air cooler / Protective filter
When cleaning, only remove the protective filter.
Clean the air cooler behind the protective filter once a year.
– Allow the dryer to cool.
– Residual water may leak out, so place an absorbent towel
underneath the maintenance door.
1. Unlock the maintenance door.
2. Open the maintenance door fully.
3. Turn both locking levers towards each another.
4. Pull out the protective filter/air cooler.
Do not damage the protective filter or air cooler.
Clean with warm water only. Do not use any hard or sharp-edged
objects.
5. Clean the air cooler thoroughly.
Allow to drip dry.
6. Clean the seals.
7. Re-insert the protective filter/air cooler,
with the handle facing down.
8. Turn back both locking levers.
9. Close the maintenance door until the lock clicks into place.
Moisture sensors
The dryer is fitted with stainless steel moisture sensors. The sensors
measure the level of moisture in the laundry. After a long period of
operation, a fine layer of limescale may form on the sensors.
1. Open the door and clean the moisture sensors with a damp sponge
which has a rough surface.
Do not use steel wool or abrasive materials.
Cover for steam nozzle in the drum
After lengthy operation, limescale and fluff may accumulate on
the cover of the steam nozzle. Clean regularly:
1. Open the door and remove the cover with a screw driver.
Clean the cover under running water.
2. Push and click the protective cap back in place.
\Only when switched off!
ʋʋ
c@c c
/c÷@c @@waHaZAa

'ˎVV÷ˎIcc+cc\aa4.uˎˎa3#9/a²aʋʋʋʋʋʋʋʋʋʋʋʋʋ.c('cacVV÷)caaaaaaaaaaaaa4\ʋʋ
7
Programme overview see also pages 5 and 8
Sort the laundry according to type of textile and fabric. Fabrics must be suitable for tumble drying. After drying...
c
iron laundry

lightly iron laundry
@c
do not iron laundry
c
mangle laundry
PROGRAMMES TEXTILE TYPE AND INFORMATION **Cottons max. 8 kg Hard-wearing fabrics, boil-resistant fabrics made of cotton or linen.
**Easy-Care max. 3.5 kg Non-iron laundry made of synthetic fibres and blended fabric, easy-care cotton. **/Mixed Load max. 3 kg Mixed items of laundry madeof cotton and synthetics (Mix).
Iron Dry c÷@c Fabrics suitable for ironing (iron fabrics in order to avoid creasing). Cupboard Dry @Single-layer fabrics.
*Extra Dry @Fabrics made of thick, multilayered items of clothing.
wSteam Dry For smoothing hard-wearing and easy-care fabrics. Steam smooths the fabrics. Minimum Iron Daily Load max. 2.5 kg Further information aPage 8. Minimum Iron Shirt max. 1.5 kg HSteam Refresh For freshening hard-wearing and easy-care fabrics. Steam freshens up the fabrics. Business max. 1.5 kg Further information aPage 8. Freshen up max. 1.0 kg ZSportswear max. 1.5 kg Fabrics with membrane coating, water-repellent fabrics, functional clothing, fleece fabrics (dry jackets/trousers with
removable internal lining separately).
Woollens Finish max. 3 kg Woollen fabrics suitable for washing machines. Fabrics become fluffier but not dry.
Remove fabrics once the programme has ended and allow to dry.
ASuper Quick 40’ max. 2 kg
Laundry made of synthetic fibres, cotton or blended fabrics (for example) that needs to be dried quickly. The values may
differ from the those specified depending on the type of fabric, mixture of laundry to be dried, residual moisture in the fabric and loading capacity.
Timed Programmes warm max. 3 kg Pre-dried, multi-layered, sensitive fabrics made of acrylic fibres, or separate small items of laundry.
Also for subsequent drying.
*for Cottons and Easy-Care programmes only
**Dryness levels can be selected individually aExtra Dry, Cupboard Dry and Iron Dry (depending on the model).
Degree of dryness can be finely adjusted; multi-layered textiles require a longer drying time than single-layered items of clothing. Recommendation: Dry separately.
9202 / 9000746180 *746180* Robert Bosch Hausgeräte GmbH
Carl-Wery-Str. 34
D-81739 Munich/Germany
WTS86500GB

8
Steam Drying - Steam Refresh
Steam programmes for unwrinkling or refreshing
– Your dryer has unwrinkling and refreshing programmes that can be used for reducing
odours and minimising creasing in dry fabrics. Steam smooths and freshens up items of
clothing.
– Sorting the laundry according to size, weight, fabric and colour is necessary.
– Only use Short spin/Refresh for fabrics with the same properties.
– During steam generation (required), additional noises may occur.
– The result of refreshing and unwrinkling may vary depending on the type of fabric, size of
the load and programme selected.
– After unwrinkling or refreshing, all fabrics must be removed immediately and hung crease-
free on a hanger or a washing line for 15 minutes.
Programmes
Please observe the treatment symbols and manufacturer's instructions on the fabrics.
Do not use Short spin/Refresh for fabrics made of wool, leather, containing metal or
wooden parts as well as wax and oil jackets!
Do not use any dryer cleaning sets!
ʑwSteam Dry
Minimum Iron Shirt
Suitable for easy-care fabrics, e.g. formal shirts. Fabrics are smoothed. You can expect
optimum results if “non-iron” appears on the care label. After the programme has finished,
the items must be removed immediately and hung crease-free on a hanger or washing line
for 15 minutes. The programme is for up to 5 formal shirts.
Minimum Iron Daily Load
Suitable for hard-wearing cotton fabrics, e.g. bed linen, tablecloths or formal shirts. Fabrics
are smoothed. You can expect optimum results if “non-iron” appears on the care label. After
the programme has finished, the items must be removed immediately and hung crease-free
on a hanger or washing line for 15 minutes. The programme is for up to 5 formal shirts or
1 to 2 larger items.
ʑHSteam Refresh
Business
Suitable for refreshing suits, jackets and trousers, or dry-clean items that cannot be washed
in the washing machine asee the care label. The programme only refreshes fabrics and
does not clean them. After the end of the programme, the items must be removed
immediately. Programme for 1 suit or 1 to 2 smaller items.
Freshen up
Suitable for refreshing casual wear made of cotton or artificial fibres. Fabrics must be
suitable for dryers asee the care label. The programme refreshes fabrics only, and does
not clean them. After the programme has finished, the fabrics must be removed
immediately. Programme for 1 pullover, 2 pairs of trousers or formal shirts.
9
Steam Drying - Steam Refresh
Your water tank empties automatically after the programme has finished.
Cleaning is therefore not required
Filling the water tank:
Fill the dryer's water tank with distilled water before every Steam Dry - Steam Refresh cycle.
1. Move the programme selector to Steam Dry
or Steam Refresh.
The usymbol appears in the display.
2. Remove the condensation tank completely.
Before every Steam Dry - Steam Refresh cycle, fill the water tank with
distilled water only. Do not use tap water, condensation or additives.
3. Fill the water tank. Use the jug supplied.
If the water tank filter is dirty aclean the filter in the water tank.
See page 4.
4. Pour the distilled water into the filling hole on the water tank,
until the usymbol goes out on the display panel.
If drying the recommended load, approximately 250 to 300 ml of distilled
water is used in the Steam Dry - Steam Refresh programmes.
5. Insert the condensation container all the way.
6. Start the Steam Dry or Steam Refresh programme.
aaaa
ʠʠIʠaʠʠāaʠ4aaʠuaaʠʠʠʠʠʠaʠaaaaʠaaaaaʠʠaaʠaaaaaaaaaa

ʑwʑHaauau
10
Installation
– Scope of delivery: dryer, installation and instruction manual, jug, basket for woollens
(depending on the model).
– Check dryer for transport damage.
– The dryer is heavy. Do not attempt to lift it on your own.
– Be careful to avoid sharp edges.
– Do not install in a room where there is a risk of freezing. Freezing water may cause damage.
– If in doubt, have the appliance connected by a specialist.
– Do not lift the dryer by protruding parts (e.g. the door) - risk of breakage.
Setting up the dryer
– The appliance plug must always be accessible.
– Ensure that the appliance is installed on a clean, level
and firm surface.
– Keep the cooling grille on the front of the dryer
clear.
– Keep the area around the dryer clean.
– Level the dryer using the threaded feet.
Use a spirit level.
– Do not remove the threaded feet under any
circumstances.
Mains connection see safety information aPage 13.
– Connect to an AC earthed socket. If in doubt, have the socket checked by a specialist.
– The mains voltage and the voltage shown on the rating plate (aPage 11) must be the same.
– The connected load and necessary fuse protection are specified on the rating plate.
Frost protection / Transport
Preparation
1. Empty the condensation container aPage 4.
2. Select any programme using the programme selector.
3. Press the Start/Stop button acondensation is pumped into the container.
4. Wait 5 min., and then empty the condensation container again.
5. Turn the programme selector to Off.
The water tank must not contain any distilled water. If necessary, run the Steam/Refresh programme.
1.
Remove all accessories
from the drum.
The drum must be empty.
Make sure that the air inlet
remains unobstructed
Clean and level
Do not install the dryer behind a door or sliding
door, which could prevent or restrict opening of the
dryer door. This will prevent children from locking
themselves in and putting their lives in danger.
2.
Do not operate the dryer if there
is a danger of frost.
11
Technical data
ʠDimensions (DxWxH) 60 x 60 x 85 cm (adjustable height)
Weight approximately 43.5 kg
Max. capacity 8 kg
Condensation container 4.0 l
Water tank approx. 0.4 l
Connection voltage 220-240 V
Connected load max. 2800 W
Fuse protection 13 A
Ambient temperature 5 - 35 °C
Product number
Production number Inside of door
The rating plate can be found on the back of the dryer.
ʠConsumption rates These are guide values determined under standard
conditions.
Spin speed in rpm
(residual moisture)
Drying time
in min.**
Energy
consumption
in kWh**
Cottons 8 kg
Cupboard Dry* 1400 (approx. 50 %) 105 3.74
1000 (approx. 60 %) 122 4.49
800 (approx. 70 %) 139 5.17
Iron Dry* 1400 (approx. 50 %) 83 2.24
1000 (approx. 60 %) 100 3.44
800 (approx. 70 %) 117 3.86
IEasy-Care 3.5 kg 1000 39 1.05
Cupboard Dry* 800 (approx. 40 %) 42 1.35
600 (approx. 50 %) 51 1.65
*Test programme to DIN EN 61121
**The values may differ from those given, depending on overvoltage and undervoltage, the
type of fabric, composition of the laundry to be dried, the residual moisture in the fabric and
the size of the load.
ʠDrum interior light (bulb E14, 25 W)
The drum is illuminated after the door is opened or closed, and after the programme has
started. The light goes out automatically. To change the bulb aPage 12.
Optional accessories (order from the after-sales service using the order number)
Connecting kit for condensation outlet
The condensation is drained off immediately via a hose.
Washer-dryer stack connection set
The dryer can be stacked on top of a suitable washing machine of the same depth and width,
to save space. The dryer must be secured to the washing machine with this connection set.
With pull-out worktop: WTZ 11300
Installation underneath the worktop
Instead of the appliance covering plate, you must have a metal cover fitted by a specialist.
WTZ
1110
WTZ
11310
WTZ
10290
ʠʠāaʠ4aaʠuaaʠʠʠʠʠʠaʠaaaaʠaaaaaʠʠaaʠ
aaaaaaaaaa

ʑwʑHaauauaaaaʠʠIʠa
12
What to do if...
If you cannot rectify a fault yourself (e.g. switching off/on), please contact our after-sales
service. We will always find an appropriate solution and will avoid unnecessary visits by
engineers. Trust the expertise of the manufacturer and rest assured that the repair will be
carried out by trained service technicians using original spare parts. The contact details of your
local after-sales service can be found in the enclosed after-sales service directory, or by
calling one of these numbers:
–GB 0844 8928979 (Calls from a BT landline will be charged at up to 3 pence per minute.
A call set-up fee of up to 6 pence may apply.)
–IE 01450 2655
When contacting the after-sales service, please quote the appliance's product number (E no.)
and production number (FD) (see the inside of the door).
Set the programme selector to Off and remove the appliance plug from the socket.
ʠThe Start/Stop indicator light
does not come on.
Mains plug plugged in?
Programme selected?
ʠThe āsymbol and Start/Stop
indicator light are flashing.
Empty the condensation container aPage 4.
Check the condensation outlet hose, if applicable (kink).
ʠThe 4symbol and Start/Stop
indicator light are flashing.
Clean the air cooler aPage 6 “Cleaning and care”. Clean the
fluff filter aPage 4.
ʠThe usymbol flashes. Is the water tank empty?
Filling with distilled water aPage 9.
The filter in the water tank may have become dirty.
If so, clean the filter in the water tank aPage 4.
ʠThe Steam Dry - Steam Refresh
does not start.
ʠDryer does not start. Has the Start/Stop button been pressed? Is the door closed?
Programme set?
Ambient temperature greater than 5 °C?
ʠWater is leaking out. Make sure the dryer is level.
Clean the air cooler seal.
ʠThe door opens by itself. Push the door closed until you hear it click into place.
ʠItems crease even though the
Steam Dry - Steam Refresh
programme has been selected.
Laundry load exceeded?
Remove articles of clothing immediately after the end of the
programme, hang up and pull into shape.
ʠCreasing. Laundry load exceeded?
Remove articles of clothing immediately after the end of the
programme, hang up and pull into shape.
Unsuitable programme selected aPage 7.
ʠDrying result is not satisfactory
(laundry feels too damp).
Warm laundry feels damper than it actually is.
The selected programme does not suit the load. Use another
drying programme or, in addition, select the time programme
aPage 7.
Use fine adjustment for the drying result aPage 1/2.
Fine layer of limescale on the humidity sensors
aClean the humidity sensors aPage 6.
Programme termination, e.g. tank full, mains power supply
failure, door open or maximum drying time reached.
ʠDrying time too long. Rinse the fluff filters under running water aPage 4.
Insufficient supply of air aensure that air can circulate.
Air inlet possibly blocked aClear inlet aPage 10.
Ambient temperature higher than 35 °C aventilate the room.
ʠThe humidity in the room increases
significantly.
Make sure the room is sufficiently ventilated.
ʠOne or more programme status
indicator lamps are flashing.
Clean the filter and air cooler under running water aPage 4/6.
Check the installation conditions aPage 10.
Switch off, allow to cool, switch on again and restart the
programme.
ʠThe interior light (depending on the
model) does not work.
Unplug the appliance plug, fold back the cover cap on the inside
above the door (using a Torx 20 screwdriver)
and replace the bulb. Close the cover cap.
13
Safety instructions
Emergency – Pull the appliance plug out of the socket immediately or disconnect the fuse.
ONLY use the
dryer...
– in rooms inside the house.
– for drying or unwrinkling/refreshing fabrics.
The dryer must
NEVER...
– be used for purposes other than those described above.
– be modified in terms of its technology or properties.
Hazards – The dryer must not be used by children or persons who have not been
instructed in its use.
– Do not leave children unsupervised near the dryer.
– Keep pets away from the dryer.
– Remove all objects from pockets,
and lighters in particular arisk of explosion.
– Do not lean or sit on the door arisk of tipping.
– Open the door carefully. Hot steam may escape. The clothes and drum may
be hot arisk of burns.
Installation – Secure loose leads or hoses, otherwise there is a risk of tripping.
– Below 0 °C there is a possibility of frost damage.
Mains
connection
– Connect the dryer according to specifications to an AC earthed socket,
otherwise it cannot be guaranteed that the appliance is completely safe.
– The cable cross-section must be sufficient.
– Only use earth-leakage circuit breakers with the following symbol:
– The appliance plug and socket must be compatible.
– Do not use multiple plugs/connectors and/or extension cables.
– Do not touch or hold the appliance plug with wet hands
arisk of electric shock.
– Never pull the appliance plug out of the socket by its cable.
– Do not damage the mains lead arisk of electric shock.
Operation – Only laundry must be loaded into the drum.
Before switching on the dryer - check the contents.
– Do not use the dryer if the laundry has been in contact with solvents, oil, wax,
grease or paint (e.g. hair setting spray, nail polish remover, stain remover,
cleaning solvent, etc.) afire/explosion hazard.
– Hazard caused by dust (e.g. coal dust, flour): do not use the dryer
arisk of explosion.
– Do not put laundry containing foamed material/rubber in the dryer aelastic
material may be destroyed and the dryer may be damaged due to possible
deformation of the foamed material.
– Switch off the dryer once the programme has ended.
– For unwrinkling/refreshing fabrics, use distilled water only. Do not use
condensation, tap water or additives.
– Distilled/condensation water is not for drinking.
Defect – Do not use the dryer if it is defective or if you suspect that it is.
Repairs must only be carried out by the after-sales service.
– Do not use a dryer with a faulty mains lead. To prevent risks, a faulty mains
lead must only be replaced by the after-sales service.
– Before changing the bulb of the interior light make absolutely sure you have
pulled the appliance plug from the socket arisk of electric shock.
Spare parts – Only use genuine spare parts and accessories for safety reasons.
Disposal – Dryer: unplug the appliance plug, then cut the mains lead from the appliance.
Dispose of the dryer at an approved public disposal facility.
– Packaging: keep all packaging out of reach of babies and children.
adanger of suffocation.
– All materials are environmentally safe and recyclable. Dispose of in an
environmentally-responsible manner.

ʑwʑHaauauaaaaʠʠIʠaʠʠāaʠ4aaʠuaaʠʠʠʠʠʠaʠaaaaʠaaaaaʠʠaaʠaaaaaaaaaa
Dryer
en Instruction manual