Bosch TDS2021GB User manual

sensixx B20L
Operating instructions

2
en











  
  



 







Description
1. Water tank
2 Removable iron pad
3 Steam hose storage fixing
4 Carrying handles
5 Mains cable storage compartment
6 Mains cable
7 Steam hose
8 “Energy Saving” button *
9 “Steam ready” pilot light
10 Variable steam control *
11 “Refill water tank” pilot light
12 Illuminated main power button (0/I)
13 Housing with internal steam generator
14 Temperature control knob
15 Steam release button “Pulse steam”.
16 Steam release button “Ultimate Steam” *
17 Iron pilot light
18 Soleplate
* Model dependent

3
en
Thank you for buying the B20L professional
steam station, the new professional steam-
ironing system from Bosch. These instructions
contain valuable information about the unique
features of this iron and some hints to make
ironing easier for you.
Please visit www.bosch-home.co.uk for
more product information or to register
your product, just follow the link to the
Online guarantee registration.
Introduction
This powerful system produces continuous
steam for an ideal ironing performance. It has a
large water tank that can be refilled at any time
without switching off the system.
We hope that you enjoy ironing with this steam
station.
Important
Please read these instructions for use carefully
before using the appliance and save them for
future reference.
This appliance complies with international safety
standards.
This appliance has been designed
exclusively for domestic use and must not
be used for industrial purposes.
Warning:
The steam hose, the housing of the steam
generator and in particular the iron can get
hot when used. This is normal.
General safety instructions
• This appliance is to be connected and used in
accordance with the information stated on its
characteristics plate.
• This appliance must be connected to an
earthed socket. If it is absolutely necessary
to use an extension cable, make sure that it
is suitable for 16A and has a socket with an
earth connection.
• The iron should not be used if it has been
dropped, if there are visible signs of damage
or if it is leaking water. It must be checked by
an authorized Technical Service Centre before
it can be used again.
• If the safety fuse fitted in the appliance blows,
the appliance will be rendered inoperative. To
restore normal operation the appliance will
have to be taken to an authorised Technical
Service Centre.
• In order to avoid that, under unfavourable
mains conditions, phenomena like transient
voltage drops or lighting fluctuations can
happen, it is recommended that the iron is
connected to a power supply system with a
maximum impedance of 0.27 Ω. If necessary,
the user can ask the public power supply
company for the system impedance at the
interface point.
• This appliance is not intended to be used
by persons (including children) with reduced
physical, sensory or mental capacities, or lack
of experience and knowledge, unless they
have been given supervision or instruction
concerning the use of the appliance by a
person responsible for their safety.
• Children should be supervised to ensure that
they do not play with the appliance.
• Remove the plug from the socket before
pouring out the remaining water after use.
• The appliance must never be placed directly
under the tap to fill the water tank.
• The appliance must be used and placed on a
stable surface.
• When placed on its stand, make sure that
the surface on which the stand is placed is
stable.
• The iron must not be left unattended while it is
connected to the supply mains.
• Unplug the appliance from the mains supply
after each use, or if a fault is suspected.
• The electrical plug must not be removed from
the socket by pulling the cable.
• Never immerse the iron or steam tank in water
or any other fluid.
• Do not leave the appliance exposed to
weather conditions (rain, sun, frost, etc.).
• With the aim of avoiding dangerous situations,
any work or repair that the appliance may

4
en
need, e.g. replacing a faulty mains cable, must
only be carried out by qualified personnel from
an Authorised Technical Service Centre.
Important :
• This appliance reaches high temperatures and
produces steam during use, this could cause
scalds or burns in case of improper use.
• Never aim the steam at people or animals.
• Do not allow the power cable to come into
contact with the soleplate when it is hot.
Getting started
1. Remove any label or protective covering from
the soleplate.
2. Place the appliance horizontally on a solid,
stable surface. You may remove the iron pad
from the appliance and place the iron on it on
another solid, stable, horizontal surface.
3. Fill the water tank, making sure not to pass
the level mark.
4. Unwind the mains cable (6) fully and plug it
into an earthed socket.
5. Set the main power button (12) to the “I”
position.
6. The “Steam ready” indicator lamp (9) will light
up after several minutes, indicating that the
appliance is ready to use.
When using the steam generator for the
first time, or when using it straight after
“Calc’nclean”, the steam generator will take
slightly longer to heat up.
7. This appliance has a built-in water level
sensor. The “refill water tank” indicator (11)
will light when the water tank is empty.
  
  
Important:
• Normal tap water can be used.
To prolong the optimum steam function, mix
tap water with distilled water 1:1. If the tap
water in your district is very hard, mix tap
water with distilled water 1:2.
You can inquire about the water hardness
with your local water supplier.
• The water tank can be filled at any time while
using the appliance.
• To avoid damage and/or contamination of the
water tank and the boiler, do not put perfume,
vinegar, starch, descaling agents, additives or
any other type of chemical product into the
water tank.
Any damage caused by the use of the
aforementioned products, will make the
guarantee void.
• The iron is not designed to rest on its heal.
Please always position it horizontally on the
iron pad (2).
• The iron pad can be placed into the specially
designed recess on the appliance or
somewhere suitable alongside the ironing
area.
Never rest the iron on the appliance
without the iron pad!.
• During its first use the iron may produce
certain vapours and odours, along with white
particles on the soleplate, this is normal and it
will stop after a few minutes
• While the steam release button is pressed, the
water tank may produce a pumping sound,
this is normal, indicating that water is being
pumped to the steam tank.
* model dependent

5
Setting the temperature
1. Check the ironing instruction label on the
garment to determine the correct ironing
temperature.
2. Turn the temperature selector (14) to the
required setting:


• Synthetics
•• Silk – Wool
••• Cotton – Linen
3. The indicator lamp (17) will remain lit while the
iron is heating and go out as soon as the iron
has reached the selected temperature.
Tips:
• Sort your garments out based on their
cleaning symbol labels, always starting with
clothes that have to be ironed at the lowest
temperatures.
• If you are not sure what the garment is made
of then begin ironing at a low temperature and
decide on the correct temperature by ironing
a small section not usually seen when worn
Ironing with steam
1. Turn the temperature selector (14) to the
required setting.
2. Set the amount of steam to suit your needs,
using the variable steam control (10*).
  
  
For normal use, please choose one of the
following recommended settings:
Temperature Steam setting
•
••
•••
3. Press the steam release button (15 or 16*) to
release steam.












Attention:
When ironing on a lower temperature setting “•”.
• If the appliance has variable steam control
(10*), set the variable steam control to its
lowest position .
• If the appliance does not have variable steam
control, press the steam release button only
for a few seconds at a time when ironing at
lower temperatures.
In both cases, if you find that water is dripping
out of the soleplate, set the temperature
selector (14) to a higher position (take care
that the garment can be ironed on this heat
temperature setting).
en
* model dependent

6
en
“Pulse steam” function
This appliance has a special function for tackling
difficult creases.
When the steam release button is activated, the
steam generator will give three powerful shots of
steam so that the steam reaches even deeper
into the fabrics.
1. Set the temperature selector (14) on “• • •”
2. Press the steam release button (15) on
the bottom of the handle two times shortly
(double-click).
or (model dependent)
Shortly press the steam release button (16*)
on the top of the handle.
Remark : It is possible to stop the shots of steam
by pressing the steam button shortly again.
“Ultimate steam” function
(model dependent)
The “Ultimate steam” function helps to de-crease
more stubborn materials found in garments
like Jeans or linen tablecloth. When activating
the “Ultimate steam” button (16*) the steam
generator produces an extra amount of steam.
The function should be used during intervals of a
few seconds, to be the most effective.
1. set the temperature selector (14) on “•••”
2. press the “Ultimate steam” button (16*).
Important:
• The steam hose may get hot if you are ironing
for long periods.
• Note: Some water drops may appear when
you use the “Pulse steam” or the “Ultimate
steam” function for the first time. The water
drops will disappear after you have used the
function for some time.
Intelligent steam
(model dependent)
This system has intelligent steam control, which,
after releasing the steam release button (15),
provides a small amount of additional steam.
The additional steam can always be stopped by
briefly pressing the steam release button once
again.
Ironing without steam
1. Begin ironing but without pressing the steam
release button.
Vertical steam
1. Set the temperature control to the “•••” or
“max” position.
2. You can steam iron curtains and hanging
garments (jackets, suits, coats...) by placing
the iron in a vertical position and pressing the
steam release button.









Never direct the steam jet at garments
that are being worn.
Never aim the steam at people or animals.
Energy saving “eco” button
(model dependent)
If the “Energy saving” button (8*) is switched on,
the energy consumption of the appliance will be
reduced, by means of an automatic reduction
of electricity and water consumption. A good
ironing result will still be obtained for most of
the garments.
* model dependent

7
en
Use the normal energy setting for thick and
highly wrinkled fabrics.
Note: If you work with the “Energy saving”
function, the variable steam regulation and
temperature regulation can still be used as
recommended.
Cleaning & Maintenance
Always unplug the appliance from the mains
supply before carrying out any cleaning or
maintenance operation on it.
1. After ironing, pull out the plug and allow the
appliance to cool down before cleaning.
2. Wipe the housing, handle and iron body with
a damp cotton cloth.
3. If the soleplate is soiled with dirt or scale,
clean it with a damp cotton cloth.
4. Never use abrasive products or solvents.
Storing the appliance
1. Always allow the appliance to cool down
before storing it.
2. Set the main power to the “0” position and
disconnect the mains cable.
3. Place the iron on the iron pad, standing on the
soleplate.
4. Store the mains cable in the storage
compartment (5) and the steam hose in the
storage fixing (3). Do not wrap the cords too
tight.
5. Use the carrying handles (4) on the sides
when moving the appliance.
  
Additional accessories
(model dependent)
Fabric protection soleplate cover
The fabric-protection soleplate cover is used for
steam ironing delicate garments at maximum
temperature without damaging them. Use of the
soleplate cover also does away with the need for
a cloth to prevent shine on dark materials.
It is advisable to first iron a small section on the
inside of the garment to see if it is suitable.
To attach the soleplate cover to the iron, place
the tip of the iron into the end of the soleplate
cover and pull the elastic strap over the lower
rear of the iron until it fits tightly. To release the
soleplate cover, pull the elastic strap and remove
the iron.
The fabric-protection soleplate cover may
be purchased from the customer service or
specialist shops:
Accessory code
(After-sales)
Name of accessory
(Specialist outlets)
571510 TDZ2045


















* model dependent

8
“Calc‘n clean”
Cleaning the Boiler
To extend the life of your steam generator and
to avoid any build up of scale, it is essential that
you rinse out the boiler after several hours of use
(approximately after 50 hours). If the water is
hard, increase the frequency.
Do not use descaling agents for rinsing out the
boiler, as they could damage it.
1. Check that the appliance is cold and
unplugged for more than 2 hours, and that
the water tank (1) is empty.
2. Place your appliance on the edge of your
kitchen sink, so that any residual water in the
water tank is directed into the sink.
3. Remove the plastic cover located on the
bottom of the appliance by turning it to the
position.
4. Unscrew the boiler drainage plug using a
coin.
5. Holding your steam generator in an upside
down position, and using a jug, fill the boiler
(in the base unit) with 1/4 litre of water
6. Shake the base unit for a few moments and
then empty it completely over a sink or bucket.
To obtain the best result, we recommend that
this operation is done twice.
Important: before closing, make sure no
water remains in the boiler.
7. Replace and tighten up the boiler drainage
plug with a coin.
8. Insert and close the plastic cover by turning it
to the position.









en
* model dependent

9



 
 
































Rinsing the iron steam
chamber
Caution! Risk of burns!
This procedure helps to remove scale particles
out of the steam chamber.
Carry it out approximately every 2 weeks, if the
water in your area is very hard.
a) Ensure that the iron is cooled down.
b) Set the temperature selector (14) of the iron to
the “min” position.
c) Fill the tank with tap water.
d) Plug in the mains cable and set the main
power switch (12) to the “I” position.
e) Wait until the “steam ready” indicator lamp (9)
lights up.
f) If the steam station has steam regulator (10*),
set it to the maximum position .
g) Hold the iron over the sink or a container to
collect the water.
h) Press the steam release button (15) and gently
shake the iron. Boiling water and steam will
come out, carrying scale and deposits that
might be there. This could take approximately
5 minutes.
i) Set the temperature selector (14) of the iron
to the “max” position, without pressing the
steam release button (15). The water in the
steam chamber will start evaporating. Wait
until all the water inside the steam chamber
has evaporated and steam is no longer
coming out from the soleplate.
j) To clean the soleplate, immediately rub off
any residue by running the hot iron over dry
cotton cloth.
en
* model dependent

10
Trouble shooting
Problem Possible causes Solution
The steam generator
does not come on.
• There is a connection problem.
• The main power button is not
switched on.
• Check the mains cable, the plug and
the socket.
• Set the main power button (12) to the
“I” position.
The iron does not
heat up.
• The main power button is not
switched on.
• The temperature control knob is
set to the “min” position.
• Set the main power button (12) to the
“I” position.
• Set the temperature control knob (14)
to the desired position.
The iron begins to
smoke when switched
on.
• During first use: Certain
components on the appliance
have been lightly greased at the
factory and may produce a little
smoke when initially heated.
• During later use: the soleplate
may be soiled.
• This is completely normal and will stop
after a short while.
• Clean the soleplate according to the
cleaning instructions in this manual.
Water flows through
the holes on the sole
plate.
• The steam function is being
used before it has reached
temperature.
• The water is condensing inside the
pipes because steam is being used
for the first time or has not been
used for a long time.
• Reduce the steam flow when ironing
at low temperatures by adjusting the
variable steam control (10*).
• Point the iron away from the ironing
area and press the steam release
button until steam is produced.
Dirt comes out
through the sole plate.
• There is a build-up of scale or
minerals in the steam tank.
• Chemical products or additives
have been used.
• Use tap water mixed 50% with distilled
or demineralised water. If the tap water
in your district is very hard, mix tap
water with distilled water 1:2.
• Clean the sole plate with a damp cloth.
• Never add products to the boiler water.
The iron does not
produce any steam.
• The boiler is not switched on or
the water tank is empty.
• The steam regulator is set to the
minimum position.
• Set the main power button (12) to the
“I” position and/or fill the water tank.
• Increase the steam flow by turning the
steam control (10*).
The ironed garment
turns dark and/or
sticks to the soleplate.
• The selected temperature is
too high and has damaged the
garment.
• Select a suitable temperature for the
material being ironed and clean the sole
plate with a damp cloth.
The soleplate turns
brown.
• This is a regular consequence of
usage.
• Clean the soleplate regularly with a
damp cloth.
The appliance makes
a pumping sound.
• Water is being pumped into the
steam tank.
• The sound will not stop.
• This is normal.
• If the sound will not stop, do not use
the steam generator and contact an
authorised technical service centre.
en
* model dependent

11
Advice on disposal
Our goods come in optimised packaging. This
basically consists in using non-contaminating
materials which should be handed over to the
local waste disposal service as secondary raw
materials. Your local town council can give you
information about how to dispose of obsolete
appliances.
This appliance is labelled in
accordance with European
Directive 2002/96/EG concerning
used electrical and electronic
appliances (waste electrical and
electronic equipment - WEEE).
The guideline determines the framework for
the return and recycling of used appliances
as applicable throughout the EU.
Guarantee conditions
The terms of the guarantee for this appliance
are in accordance with that stated by our
representative for the country in which it is sold.
The details of these conditions can be obtained
from the retailer from whom the appliance was
purchased. The purchase receipt must be
presented when making any claims against the
terms of this guarantee.
Problem Possible causes Solution
Loss of pressure
during ironing.
Steam release button activated for
a long period of time.
Use the steam release button with
intervals. This improves the ironing result
as the textiles will be steamed and dried
properly giving a smoother result..
Waterspots appear
on the garment during
ironing.
May be caused by steam
condensed on the ironing board.
Wipe the textile cover of the ironing
board, and iron the spots without steam
to dry them.
Water spots appear
on the garment during
use of the “Ultimate
steam” function
Water spots are caused by steam
condensation in the hose when
cooling down after use.
Water drops stop coming out of the
soleplate after using the “Ultimate steam”*
function for some time.
The hose gets hot
during use.
This is normal. It is caused by the
steam passing through the hose
during steam ironing.
Ensure that the steam generator is
positioned to the side of the hand you are
using to iron, to reduce contact with the
hose as much as possible.
Water leakage from
the boiler
Drainage plug located at the
bottom of the appliance is loose.
Tighten up boiler drainage plug with a
coin
The iron does not stop
steaming after placing
it on the pad.
• “Pulse steam” function may have
been activated by the double
click.
• The steaming will not stop
• Just press the trigger once again and
the iron will stop steaming at once.
• Contact an authorized technical service
centre.
* model dependent
If the above does not solve the problem, get in touch with an authorized technical service.
en

001 TDS20..GB/04/11
Great Britain
Bosch Customer Service
Grand Union House
Old Wolverton Road
Milton Keynes
MK12 5PT