Bosch VIP-X1600-XFM4A User manual

VIP X1600 XFM4
VIP-X1600-XFM4A/VIP-X1600-XFM4B
en Quick Installation Guide
All manuals and user guides at all-guides.com
all-guides.com

VIP X1600 XFM4 General Information | en 2
Bosch Security Systems Quick Installation Guide F.01U.088.580 | V4.0 | 2009.03
1 General Information
These instructions "Quick Installation Guide" refer to encoder
modules VIP X1600 XFM4A and VIP X1600 XFM4B. The encoder
modules are intended for installation in the following devices:
– VIP X1600 XF base
– VIP X1600 B base
The VIP X1600 base is not supported.
You can find further detailed information in the extensive online
help for the device in question.
Additional language versions of these instructions "Quick
Installation Guide", the Installation and Operating Manuals for
the VIP X1600 XFM4 encoder module and the base being used,
as well as the 4.0 firmware are available on
www.boschsecurity.com.
!
CAUTION!
You should always make yourself familiar with the required
safety measures in the relevant chapters of the Installation and
Operating Manuals for the VIP X1600 XFM4 encoder module
and the base being used (see product CD in the scope of
delivery for the base being used). The manuals on the product
CD contain important information on the installation and
operation of the devices.
These instructions "Quick Installation Guide" only show the
basic installation of a VIP X1600 XFM4A or VIP X1600 XFM4B
encoder module, they are no substitute for the complete user's
manual.
All manuals and user guides at all-guides.com

3en | Scope of Delivery VIP X1600 XFM4
F.01U.088.580 | V4.0 | 2009.03 Quick Installation Guide Bosch Security Systems
2 Scope of Delivery
– VIP X1600 XFM4A or VIP X1600 XFM4B encoder module
– Two terminal blocks
– Four screws for installation in the base
– Quick Installation Guide
All manuals and user guides at all-guides.com

VIP X1600 XFM4 Unpacking | en 4
Bosch Security Systems Quick Installation Guide F.01U.088.580 | V4.0 | 2009.03
3 Unpacking
– Please check the delivery for completeness and integrity.
– Have your device checked by Bosch Security Systems if
you detect any damage!
All manuals and user guides at all-guides.com

5en | Installing and Connecting VIP X1600 XFM4
F.01U.088.580 | V4.0 | 2009.03 Quick Installation Guide Bosch Security Systems
4 Installing and Connecting
4.1 Installing Modules
– Insert the module into the guide rails of the first slot and
carefully push as far as it will go. If the first slot is already
equipped you can equip one of the other unused slots.
– First, remove the respective cover plate by unscrewing the
screw and bending the cover plate upwards.
– Insert the four screws provided in the bores on the module
and tighten.
– After a module has been removed, you must reseal the
empty slot with a cover to ensure correct air circulation.
All manuals and user guides at all-guides.com

VIP X1600 XFM4 Installing and Connecting | en 6
Bosch Security Systems Quick Installation Guide F.01U.088.580 | V4.0 | 2009.03
4.2 Connecting Cameras
– Connect one camera to each, the Video In 1 socket to the
Video In 4 socket.
All manuals and user guides at all-guides.com
all-guides.com

7en | Installing and Connecting VIP X1600 XFM4
F.01U.088.580 | V4.0 | 2009.03 Quick Installation Guide Bosch Security Systems
4.3 Alarm and Switch Connections
– Connect the alarm lines to terminals lN1 to IN4 and GND
on the 8-pin terminal block.
– Connect the relay lines to the two R1 terminals on the 8-
pin terminal block.
– Secure the terminal block onto the left-hand part of the
male multipoint connector.
!
CAUTION!
A maximum load of 30 V and 500 mA may be applied to the relay
contact.
All manuals and user guides at all-guides.com

VIP X1600 XFM4 Installing and Connecting | en 8
Bosch Security Systems Quick Installation Guide F.01U.088.580 | V4.0 | 2009.03
4.4 Serial Interface
– Connect the serial-connection lines to the corresponding
terminals on the 6-pin terminal block as required.
– Secure the terminal block onto the right-hand part of the
male multipoint connector.
All manuals and user guides at all-guides.com

9en | Installing and Connecting VIP X1600 XFM4
F.01U.088.580 | V4.0 | 2009.03 Quick Installation Guide Bosch Security Systems
4.5 Audio Connections
– Use the Audio In and Audio Out sockets for the audio line
connections.
Line In Input voltage 5.5 Vp-p max.,
impedance 9 kOhm typ.
Line Out Output voltage 3 Vp-p at 10 kOhm /
1.7 Vp-p at 16 Ohm typ.
All manuals and user guides at all-guides.com

VIP X1600 XFM4 Configuration | en 10
Bosch Security Systems Quick Installation Guide F.01U.088.580 | V4.0 | 2009.03
5 Configuration
5.1 Assigning an IP Address
– If you have not already done so, install the
Configuration Manager program from the product CD. The
product CD is included in the scope of delivery for the
base.
– Start Configuration Manager when the installation is
completed. The network is scanned for compatible devices
automatically.
– If the module is displayed in the list, right-click the entry
and then click Unit network settings... in the popup menu.
– Enter the desired IP address (e.g. 192.168.0.116) in the
Unit IP address field and click OK. The module is rebooted
and the IP address is valid.
Note:
The module must be assigned a valid IP address and a matching
subnet mask to operate on your network.
All manuals and user guides at all-guides.com